乙醇胺功能化石墨烯的制备与表征

乙醇胺在温和条件下与氧化石墨烯反应, 然后经水合肼还原得到功能化的石墨烯. 干燥的功能化石墨烯经超声处理后, 可稳定分散于水、乙醇、丙酮和N,N二甲基甲酰胺(DMF)等溶剂中. 原子力显微镜(AFM)、透射电镜(TEM)分析表明功能化石墨烯平均厚度为3～4 nm. 傅里叶变换红外光谱(FTIR)、X射线光电子能谱(XPS)、X射线衍射(XRD)对功能化石墨烯的结构分析表明: 乙醇胺与氧化石墨烯发生了化学反应, 并通过共价键连接到石墨烯的六元环上. TG结果表明功能化石墨烯的热稳定性比氧化石墨烯有所提高, 但低于还原氧化石墨烯.     

甲基丙烯酸缩水甘油酯功能化石墨烯的制备与表征

利用改进的Hummers法对天然鳞片石墨进行氧化处理制备氧化石墨烯,将其与甲基丙烯酸缩水甘油酯(GMA)在温和条件下反应,再经水合肼还原得到功能化石墨烯.分散性测试结果表明,超声后的功能化石墨烯可以稳定分散于丙酮、乙醇和N,N-二甲基甲酰胺等有机溶剂中.采用傅里叶变换红外光谱、X射线衍射分析及X射线光电子能谱对样品的结构进行了表征.结果表明,GMA上的环氧基与氧化石墨烯上的羟基发生了化学反应,键合在氧化石墨烯表面;经水合肼还原后,层间距较功能化氧化石墨烯缩小,无序度增加.扫描电子显微镜(SEM)测试结果表明,功能化石墨烯含大量褶皱和卷曲;原子力显微镜(AFM)测试结果表明,功能化石墨烯的厚度为2~3 nm.热重分析结果表明,还原氧化石墨烯的热稳定性最高,功能化石墨烯次之,氧化石墨烯的热稳定性最低.     

微波固相法快速制备氮掺杂石墨烯

以鳞片石墨为原料,首先通过Hummers法制备氧化石墨,再将洗涤至中性的氧化石墨分散液与乙二胺反应得到功能化石墨烯。干燥后的功能化石墨烯在微波辐照下能瞬间产生高热,促使接枝的乙二胺分子分解并实现对石墨烯原位掺杂制备出氮掺杂石墨烯。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶变换红外光谱(FTIR)、X射线光电子能谱(XPS)、X射线衍射(XRD)、X射线能谱(EDS)对样品的形貌、结构和组成进行了表征。结果表明:该合成途径能成功实现对氧化石墨烯的还原和掺杂,所合成的氮掺杂石墨烯呈现透明绢丝状结构。     

微波固相法快速制备氮掺杂石墨烯

以鳞片石墨为原料, 首先通过Hummers法制备氧化石墨, 再将洗涤至中性的氧化石墨分散液与乙二胺反应得到功能化石墨烯。干燥后的功能化石墨烯在微波辐照下能瞬间产生高热, 促使接枝的乙二胺分子分解并实现对石墨烯原位掺杂制备出氮掺杂石墨烯。利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶变换红外光谱(FTIR)、X射线光电子能谱(XPS)、X射线衍射(XRD)、X射线能谱(EDS)对样品的形貌、结构和组成进行了表征。结果表明:该合成途径能成功实现对氧化石墨烯的还原和掺杂, 所合成的氮掺杂石墨烯呈现透明绢丝状结构。     

水溶液体系中氧化石墨烯的γ射线辐射还原

石墨烯是一种碳原子以二维蜂窝状晶格结构构成的单片层材料,由于其具有优异的电传导性、力学性能和热传导性近年来受到广泛关注.本文采用γ射线辐射技术分别处理水溶液和对苯二胺(PPD)水溶液中的氧化石墨烯(GO),得到辐照还原氧化石墨烯(RGO)和胺基化修饰的还原氧化石墨烯(RGON).通过傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)、拉曼(Raman)光谱、X射线衍射(XRD)和热失重分析(TGA)等表征分析产物的化学结构和元素组成;通过四探针测试仪和接触角测量仪研究产物的导电性能和亲水性.实验结果表明,在水溶液及PPD水溶液中γ射线辐射均可高效还原GO,还原后得到的RGO和RGON电导率均显著增大.PPD的胺基在辐射还原过程中还可以修饰到石墨烯的表面,因此RGON的亲水性比RGO好,但胺基的存在会干扰石墨烯表面π电子的传导,导致其电导率下降.     

KH-570功能化石墨烯的制备与表征

采用Hummers法对天然石墨进行氧化处理制备了氧化石墨烯,通过γ-甲基丙烯酰氧丙基三甲氧基硅烷与氧化石墨烯反应得到功能化氧化石墨烯,然后在水合肼的作用下制备了功能化石墨烯。未烘干的功能化石墨烯在超声处理下,能稳定分散在体积比为9∶1(V/V)的乙醇/水、丙酮/水或N,N-二甲基甲酰胺/水的混合溶剂中。用傅立叶变换红外光谱、原子力显微镜、X射线光电子能谱及X射线衍射对样品结构、形貌进行了分析。结果表明,KH-570上的硅氧烷与氧化石墨烯上的羟基发生了反应,经水合肼还原后,功能化石墨烯的无序度增加,层间距也比功能化氧化石墨烯的缩小了。功能化石墨烯在DMF/水中呈高度剥离状态,片层厚度为1.1～2.3 nm。     

氮掺杂石墨烯的制备及氧还原电催化性能

采用两步热解法, 用尿素掺杂氧化石墨烯(GO)得到N掺杂的还原氧化石墨烯(N-RGO), 通过控制反应温度, 制备了具有不同电催化活性的N掺杂的还原氧化石墨烯. 透射电子显微镜(TEM)和扫描电子显微镜(SEM)结果显示, 制得的氮掺杂石墨烯(nG)表面褶皱和重叠增加. X射线光电子能谱(XPS)证明, 氮元素以吡啶N、 吡咯N和石墨化的N 3种形式掺杂在石墨烯中, 最高摩尔分数为6.6%. 通过循环伏安(CV)和旋转圆盘电极(RDE)测试了nG的电化学性能, 结果表明, 在酸性电解质中对氧还原(ORR)有较高的催化活性, 起始电位在0.1 V左右, 电催化还原氧气时主要为四电子反应, 且相对商用的Pt/C催化剂有更好的电化学稳定性, 其中第一步热解温度为200℃制得的nG催化性能最好.     

改进的石墨烯基材料用作菜籽油转酯化反应制生物柴油的有效催化剂（英文）

本文研究了不同石墨烯基材料用作转酯化反应制备生物柴油催化剂的性能.将磺酸基或磷酸盐基嫁接到热还原的氧化石墨烯表面,制备了固体酸石墨烯基样品.并采用扫描电镜、X射线衍射、热重分析、X射线光电子能谱、N_2吸附-脱附法、电位滴定法、元素分析以及红外光谱法对所制样品进行了全面表征.将所制样品用于130℃带压力的条件下菜籽油与甲醇转酯化反应中,并将其催化活性与商用的多相酸催化剂Amberlyst-15的进行了比较.结果表明,所有改进的样品在转酯化反应中均表现出催化活性,但各样品上生物柴油产率差别较大.其中以苯二氮磺酸基功能化的热还原氧化石墨烯样品上脂肪酸甲酯产率最高,反应6 h后达70%,也明显高于商用催化剂Amberlyst-15.该样品也表现出良好的重复使用性能.     

正丁基氯化镁还原氧化石墨烯的表征

采用元素分析、红外光谱(FTIR)、X射线光电子能谱(XPS)、拉曼光谱、X射线衍射(XRD)、固体¹³C核磁共振波谱(¹³C MAS NMR)、热失重分析(TGA)、导电率测试以及原子力显微镜(AFM)等手段对正丁基氯化镁还原的氧化石墨烯进行了系统的表征. 结果表明, 正丁基氯化镁可以有效还原氧化石墨烯, 随着其用量的增加, 氧化石墨烯还原程度增加, 碳/氧摩尔比升高, 片层间距减小, 热稳定性增强, 导电率增大(可达3.6×10² S/m). 还原后部分氧化石墨烯片层发生聚集.     

高活性、可循环的Pt-Cu@3D石墨烯复合催化剂的制备和催化性能（英文）

以氧化石墨烯为前驱体,通过氧化还原法制备了具有三维大孔稳定结构的Pt-Cu@3D石墨烯催化剂。作为载体,三维石墨烯的宏观大孔结构具有大比表面积,可以更好地促进催化反应中的传质过程。以对硝基苯酚的还原为模型反应,通过实验确定Pt与Cu的最佳质量比为3:5,利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、X射线衍射(XRD)和能量色散X射线光谱(EDX)等方法对最优催化剂的结构进行了表征。催化测试表明复合催化剂在对硝基苯酚还原反应中具有高效稳定、低成本、可循环的良好性能。     

氮掺杂还原氧化石墨烯负载铂催化剂的制备及甲醇电氧化性能

采用高温热解聚苯胺修饰的氧化石墨烯（PANI-GO）,得到了氮掺杂的还原氧化石墨烯碳材料（N-RGO）,以其负载Pt 制备了Pt/N-RGO纳米结构电催化剂. 采用透射电镜（TEM）、X射线光电子能谱（XPS）、X 射线衍射（XRD）谱及拉曼光谱等技术对N-RGO和Pt/N-RGO的形貌及结构进行了表征,用循环伏安、计时电流等电化学技术研究了Pt/N-RGO电极催化剂对CO溶出反应和甲醇电氧化反应的催化性能. 结果表明：高温热解PANIGO可同时实现GO的还原及其氮掺杂的过程,氮掺杂引起还原氧化石墨烯碳材料表面缺陷结构和导电性的增加;与相应的未掺杂氮样品Pt/RGO相比较,Pt/N-RGO样品上Pt 颗粒的分散更均匀,显示出更强的抗CO毒化能力和更高的甲醇电氧化催化活性及稳定性.     

氮掺杂还原氧化石墨烯负载铂催化剂的制备及甲醇电氧化性能

采用高温热解聚苯胺修饰的氧化石墨烯(PANI-GO),得到了氮掺杂的还原氧化石墨烯碳材料(N-RGO),以其负载Pt制备了Pt/N-RGO纳米结构电催化剂.采用透射电镜(TEM)、X射线光电子能谱(XPS)、X射线衍射(XRD)谱及拉曼光谱等技术对N-RGO和Pt/N-RGO的形貌及结构进行了表征,用循环伏安、计时电流等电化学技术研究了Pt/N-RGO电极催化剂对CO溶出反应和甲醇电氧化反应的催化性能.结果表明:高温热解PANIGO可同时实现GO的还原及其氮掺杂的过程,氮掺杂引起还原氧化石墨烯碳材料表面缺陷结构和导电性的增加;与相应的未掺杂氮样品Pt/RGO相比较,Pt/N-RGO样品上Pt颗粒的分散更均匀,显示出更强的抗CO毒化能力和更高的甲醇电氧化催化活性及稳定性.     

PtPd-nanoparticles supported by new carbon materials

Nanocomposites based on PtPd nanoparticles with chemical ordering like disordered solid solution on surface of multilayer graphene have been prepared through thermal shock of mechanically obtained mixture of double complex salt [Pd(NH₃)₄][PtCl₆] and different carbon materials–exfoliated graphite, graphite oxide and graphite fluoride. An effect of original carbon precursors on formation of PtPd bimetallic nanoparticles was studied using X-ray absorption spectroscopy (XAFS), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). It was shown that the distribution of bimetallic nanoparticles over the multilayer graphene surface as well as the particles size distribution is controlled by the graphene precursors. For all nanocomposites, the surface of the nanoparticles was found to be Pd-enriched. In case when the thermal exfoliated graphite and graphite oxide were used as the graphene precursors a thin graphitized layer covered the nanoparticles surface. Such a graphitized layer was not observed in the nanocomposite, which used the fluorinated graphite as the precursor.     

Preparation of chloro-functionalized reduced graphene oxide by silver-catalyzed radical reaction

It is well-known that chemical functionalization of graphene has the great significance.We report the development of a new synthesis method of chloro-functionalized reduced graphene oxide(rGOCl).The rGOCl was prepared by radical reaction,and treatment of carboxyl graphene oxide(GOCOOH) with N-chlorosuccinimide(NCS) at 90℃ for 10 h under an atmosphere of nitrogen,using silver nitrate as catalyst.The morphologies and structures of the prepared materials were investigated by field-emission scanning electron microscopy(FESEM),X-ray diffraction(XRD),Fourier transform infrared spectroscopy(FTIR),Raman spectroscopy and the thermal gravimetric.Results indicated that the rGOCl can be readily obtained from graphene oxide(GO) in three steps.     

One‐Pot Synthesis,Characterization, and Enhanced Photocatalytic Activity of a BiOBr–Graphene Composite

Herein, a chemically bonded BiOBr–graphene composite (BiOBr–RG) was prepared through a facile in situ solvothermal method in the presence of graphene oxide. Graphene oxide could be easily reduced to graphene under solvothermal conditions, and simultaneously BiOBr nanoplates with pure tetragonal phase were grown uniformly on the graphene surface. The structure and photoelectrochemical properties of the resulting materials were characterized by transmission electron microscopy (TEM), X‐ray diffraction (XRD), Fourier‐transform infrared (FTIR) spectroscopy, Raman spectroscopy, X‐ray photoelectron spectroscopy (XPS), and impedance and photocurrent action measurements. The combination of BiOBr and graphene introduces some properties of graphene into the photocatalysis reaction, such as excellent conductivity, adsorptivity, and controllability. A remarkable threefold enhancement in the degradation of rhodamine B (RhB) was observed with as‐prepared BiOBr–RG as compared with pure BiOBr under visible light (λ>420 nm). The enhanced photocatalytic activity could be attributed to the great adsorptivity of dyes, the extended photoresponse range, the negative shift in the Fermi level of BiOBr–RG, and the high migration efficiency of photoinduced electrons, which may effectively suppress the charge recombination.     

Noble metal doped graphene nanocomposites and its study of photocatalytic hydrogen evolution

This work reports the deposition of platinum (Pt) nanoparticles on the surface of graphene nanosheet by a simple approach, using a microwave-assisted method. The photocatalytic activity has been investigated for hydrogen evolution. The hydrogen evolutions were attributed to graphene, due to its high photoelectron transport properties, and the Pt nanoparticles attached on the surface of graphene sheet, which act as reaction centers for H₂ evolution. The “as-prepared” composites were characterized by Brunauer Emmett Teller (BET) surface area measurement, X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV–vis diffuse reflectance spectra (DRS). This work highlights the potential application of graphene-based materials in the field of energy conversion.     

一步法制备还原态氧化石墨烯载铂纳米粒子及其对甲醇氧化的电催化性能

以天然石墨为原料,采用改进的Hummers法制备氧化石墨.然后采用简单的一步化学还原法在乙二醇(EG)中同时还原氧化石墨烯(GO)和H₂PtCl₆制备高分散的铂/还原态氧化石墨烯(Pt/RGO)催化剂.采用傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)和透射电子显微镜(TEM)对催化剂的微结构、组成和形貌进行表征.结果表明, GO已被还原成RGO, Pt纳米粒子均匀分散在RGO表面,粒径约为2.3 nm.采用循环伏安法和计时电流法评价催化剂对甲醇氧化的电催化性能,测试结果表明, Pt/RGO催化剂对甲醇氧化的电催化活性和稳定性与Pt/C和Pt/CNT相比有了很大提高.另外其对甲醇电催化氧化的循环伏安图中正扫峰电流密度(I_f)和反扫峰电流密度(I_b)的比值高达1.3,分别是Pt/C和Pt/CNT催化剂的2.2和1.9倍,表明Pt/RGO催化剂具有高的抗甲醇氧化中间体CO_ad的中毒能力.     

CdS/石墨烯复合材料的制备及其可见光催化分解水产氢性能

以氧化石墨烯和CdS为原料, 在乙醇水溶液中采用CdS光催化还原法制备了CdS/石墨烯复合光催化材料, 并用透射电子显微镜(TEM)、X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、X射线光电子能谱(XPS)和瞬态光电流等技术对复合材料的结构和光电性能进行了表征. 可见光照射下(λ≥420 nm), 研究了该复合材料光催化分解水产氢的性能. 结果表明, 可见光照射下CdS的光生电子可有效地还原氧化石墨烯, 得到CdS与石墨烯之间具有强相互作用力的CdS/石墨烯复合材料. 与CdS相比, 复合材料中石墨烯作为良好的电子受体和传递介质, 可明显加快CdS光生电子的迁移速率, 提高光生载流子的分离效率, 从而增强复合材料的光电性能和光催化分解水产氢的活性.     

Preparation and characterization of palladium/polypyrrole-reduced graphene oxide/foamed nickel composite electrode and its electrochemical dechlorination of triclosan

In this study, a new composite electrode of palladium (Pd) nanoparticles dispersed on polypyrrole-reduced graphene oxide (PPy-rGO) loaded on foam-nickel was achieved by galvanostatic method. Characterization of structures, morphology and crystallinity of the synthesized materials were investigated by scanning electron microscopes (SEM), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Raman spectroscopy and electrochemical impedance spectroscopy (EIS). The results of XPS and XRD demonstrated Pd showed primarily as Pd0. From SEM and TEM results, we had seen that Pd nanoparticles were dispersible well on the composite electrode. Raman spectroscopy was used to show the state of graphene oxide and further demonstrated that PPy and rGO had existed of on the foam Ni matrix. The data of EIS also suggested the charge transfer of the new composite electrode decreased compared to Pd/PPy/foam-Ni and PPy/foam-Ni composite electrodes. The effect of the electropolymerization potential on Pd/PPy-rGO/foam-Ni electrode for removing triclosan (TCS) was examined. It was found that the removal efficiency of TCS on the composite electrode could reach 100% at electropolymerization potential of 0.7 V and reaction time of 100 min.     

Influence of parent graphite particle size on the electrochemistry of thermally reduced graphene oxide

Electrochemical applications of graphene are of very high importance. For electrochemistry, bulk quantities of materials are needed. The most common preparation of bulk quantities of graphene materials is based on oxidation of graphite to graphite oxide and subsequent thermal exfoliation of graphite oxide to thermally reduced graphene oxide (TR-GO). It is important to investigate to which extent a reaction condition, that is, composition of the oxidation mixture and size of graphite materials, influences the properties of the resulting materials. We characterised six graphite materials with a range of particle sizes (0.05, 11, 20, 32, 35 and 41 μm) and the TR-GO products prepared from them by use of scanning electron microscopy, Raman spectroscopy and X-ray photoelectron spectroscopy. Cyclic voltammetric performance of the TR-GO samples was compared using ferro/ferricyanide and ascorbic acid. We observed no correlation between size of initial graphite and properties of the resultant TR-GO such as density of surface defects, amount of oxygen-containing groups, or rate of heterogeneous electron transfer (HET). A positive correspondence between HET rate and high defect density as well as low amounts of oxygen functionalities was noted. Our findings will have profound influence upon practical fabrication of graphene for applications in sensing and energy storage devices.