Preparation and characterization of periodic mesoporous organosilica terminally functionalized with fluorocarbon groups by a direct synthesis

Fluorocarbon groups were used to modify the pore channels of ethane-bridged periodic mesoporous organosilica by the co-condensation of 1,2-Bis(triethoxysilyl)ethane (BTESE) and trifluoropropyltrimethoxysilane (TFPTMS) in the presence of Poly(ethylene glycol)-B-Poly(propylene glycol)-B-Poly(ethylene glycol) (P123) surfactants under acidic conditions. The functionalized materials were investigated in detail by means of XRD, TEM, FT-IR, solid-state NMR, and N₂ adsorption. The effect of fluorocarbon groups concentration on the mesoscopic order and pore structure of the functionalized materials was also studied. The results show that bridging groups in the framework do not cleave and fluorocarbon groups are attached covalently to the pore wall of periodic mesoporous organosilica after functionalization. The samples functionalized with 20% TFPTMS remain desired mesoporous architecture, with a narrow pore size distribution centered at 4.1 nm, a large surface of 834 m²/g and a pore volume of 0.91 cm³g⁻¹, without pronounced change compared to the pure periodic mesoporous organosilica. Unfortunately the functionalized materials become structurally disordered with increasing amount of fluorocarbon groups.     

Periodic mesoporous organosilicas with co-existence of diurea and sulfanilamide as an effective drug delivery carrier

In this article we report the synthesis of new periodic mesoporous organosilicas (PMOs) with the co-existence of diurea and sulfanilamide-bridged organosilica that are potentially useful for controlled drug release system. The materials possess hexagonal pores with a high degree of uniformity and show long-range order as confirmed by the measurements of small-angle X-ray scattering (SAXS), N₂ adsorption isotherms, and transmission electron microscopy(TEM). FT-IR and solid state ²⁹Si MAS and ¹³C CP MAS NMR spectroscopic analyses proved that the bridging groups in the framework are not cleaved and covalently attached in the walls of the PMOs. It was found that the organic functionality could be introduced in a maximum of 10 mol% with respect to the total silicon content and be thermally stable up to 230 °C. The synthesized materials were shown to be particularly suitable for adsorption and desorption of hydrophilic/hydrophobic drugs from a phosphate buffer solution at pH 7.4.     

Platinum-Imidazolyl Schiff Base Complexes Immobilized in Periodic Mesoporous Organosilica Frameworks as Catalysts for Hydrosilylation

An imidazolyl Schiff base-containing periodic mesoporous organosilica (PMO) was synthesized via co-condensation reactions between a newly prepared bis (imidazolyl)imine-bridged bis silane and tetraethyl orthosilicate in the presence of cetyltrimethyl ammonium bromide as a soft template. The resultant as-synthesized PMO was then employed as a solid support for platinum catalysts. This complex was fully characterized via various techniques including FTIR, solid-state¹³C NMR, and ²⁹Si-NMR spectroscopy, as well as N₂ adsorption/desorption analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) methods. In addition, the catalyst was proven to efficiently mediate hydrosilylation reactions between olefins and hydrosilanes, and it can be reused for at least five cycles without significant loss of activity.     

Green synthesis of 4,6-bisarylpyrimidin-2(1H)-ones and azo-linked 4-arylpyrimidin-2(1H)-ones using NiFe2O4@SiO2nPr@glucose amine as a mild nano catalyst

The clean, environmentally benign and effective synthesis of novel azo-linked 4-arylpyrimidin-2(1H)-one derivatives and 4,6-bisarylpyrimidin-2(1H)-ones via three-component reaction of various aldehydes or synthetized azo-linked aldehydes, urea, and acetophenone promoted by NiFe₂O₄@SiO₂ⁿPr@glucose amine at room temperature (25 °C) was reported. NiFe₂O₄@SiO₂ⁿPr@glucose amine were synthesized and characterized by transmission electron microscope (TEM), fourier transform infrared spectroscopy (FT-IR), vibrating sample magnetometry (VSM), X-ray powder diffraction (XRD) and X-ray spectroscopy (EDX). These compounds were obtained in high yields and short reaction times. The catalyst could be easily recovered and reused for six cycles with almost consistent activity. The structures of the synthesized 4,6-bisarylpyrimidin-2(1H)-one compounds were confirmed by ¹H NMR, ¹³C NMR and FTIR spectral data and elemental analyses.     

Flash microwave synthesis of trevorite nanoparticles

Nickel ferrite nanoparticles have several possible applications as cathode materials for rechargeable batteries, named “lithium-ion” batteries. In this study, NiFe₂O₄ was prepared by microwave induced thermohydrolysis. The obtained nanoparticles were characterized by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), BET method, transmission electron microscopy (TEM) and small angle X-ray scattering (SAXS). All the results show that the microwave one-step flash synthesis leads in a very short time to NiFe₂O₄ nanoparticles with elementary particles size close to 4-5 nm, and high specific surfaces (close to 240 m²/g). Thus, microwave heating appears as an efficient source of energy to produce quickly nanoparticles with complex composition as ferrite.     

Cu(II) immobilized on mesoporous organosilica as an efficient and reusable nanocatalyst for one‐pot Biginelli reaction under solvent‐free conditions

Cu(II) immobilized on mesoporous organosilica nanoparticles (Cu²⁺@MSNs‐(CO₂^?)₂) has been synthesized, as a inorganic–organic nanohybrid catalyst, through a post‐grafting approach. Its characterization is carried out by Fourier transform infrared spectroscopy (FT‐IR), X‐ray diffraction (XRD), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Energy dispersive X‐ray (EDX), Thermogravimetric/differential thermal analyses (TGA‐DTA), and Nitrogen adsorption–desorption analysis. Cu²⁺@MSNs‐(CO₂^?)₂ exhibits high catalytic activity in the Biginelli reaction for the synthesis of a diverse range of 3, 4‐dihydropyrimidin‐2(1H)‐ones, under mild conditions. The anchored Cu(II) could not leach out from the surface of the mesoporous catalyst during the reaction and it has been reused several times without appreciable loss in its catalytic activity.     

Preparation of porous TiO2/silica composites without any surfactants

TiO₂-SiO₂ composites, with high specific surface area (up to 308 m²/g), large pore volume, and narrow distribution with average pore sizes of 3.2 nm, have been synthesized from wollastonite and titanium sulfate in the absence of any surfactants. Calcium sulfate, a microsolubility salt, plays an important role in the formation of pores in this porous TiO₂/silica composite. The microstructure and chemical composition of composite were characterized by X-ray diffractometry (XRD), transmission electron microscopy (TEM) equipped with energy-dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectrometer (XPS) and N₂ adsorption and desorption analysis. The as-prepared porous titanium dioxide-silicon dioxide composites with high specific surface area and well-crystallized anatase contents were used as an efficient photocatalyst.     

Preparation and characterization of NiO nanoparticles from thermal decomposition of the [Ni(en)3](NO3)2 complex: A facile and low-temperature route

NiO nanoparticles with an average size of 15 nm were easily prepared via the thermal decomposition of the tris(ethylenediamine)Ni(II) nitrate complex [Ni(en)₃](NO₃)₂ as a new precursor at low temperature, and the nanoparticles were characterized by thermal analysis (TGA/DTA), X-ray diffraction (XRD), Fourier-transformed infrared spectroscopy (FT-IR), UV-Vis spectroscopy, BET specific surface area measurement, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM) and magnetic measurements. The magnetic measurements confirm that the product shows a ferromagnetic behavior at room temperature, which may be ascribed to a size confinement effect. The NiO nanoparticles prepared by this method could be an appropriate photocatalytic material due to a strong absorption band at 325 nm. This method is simple, fast, safe, low-cost and also suitable for industrial production of high purity NiO nanoparticles for applied purposes.     

Synthesis and characterization of crystalline nanosized MgF2 powder via microemulsion route

Nanosized MgF₂ was synthesized by precipitation in microemulsions of water in cyclohexane stabilized by polyethylene glycol tert-octylphenyl ether. The synthesized MgF₂ powder was characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), BET specific surface area, attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and X-ray diffraction (XRD). The results showed that the synthesized powder was a MgF₂ powder with a crystallite size in the range of 9-11 nm and a specific surface area of 190 m²/g.     

Fluorine-doped nanocrystalline SnO2 powders prepared via a single molecular precursor method as anode materials for Li-ion batteries

Fluorine-doped nanocrystalline tin dioxide materials (F:SnO₂) have been successfully prepared by the sol-gel process from a single molecular precursor followed by a thermal treatment at 450-650 °C. The resulting materials were characterized by FTIR spectroscopy, powder X-ray diffraction, nitrogen adsorption porosimetry (BET) and transmission electron microscopy (TEM). The mean particle size increased from 5 to 20 nm and the specific surface area decreased from 123 to 37 m²/g as the temperature of heat treatment was risen from 450 to 650 °C. Fluorine-doped nanocrystalline SnO₂ exhibited capacity of 560, 502, and 702 mA h/g with 48%, 50%, and 40% capacity retention after 25 cycles between 1.2 V and 50 mV at the rate of 25 mA/g, respectively. In comparison, commercial SnO₂ showed an initial capacity of 388 mA h/g, with only 23% capacity retention after 25 cycles.     

Exfoliation of smectite clays by branched polyamines consisting of multiple ionic sites

Exfoliation through an ionic exchange reaction of layered silicate clays, including synthetic fluorinated mica (Mica) and natural montmorillonite (MMT), were achieved by using polyvalent amine salts as the intercalating agents. The requisite polyamine was synthesized from the epoxy/amine coupling reaction, involving a trifunctional poly(oxypropylene)-triamine (ca. 440 g/mol M_w) and diglycidyl ether of bisphenol-A. The polyamine was a mixture of oligomeric adducts consisting of multiple amine functionalities and a branched backbone. Partial acidification by HCl addition generated a series of amine salts that affected the intercalation and the expansion of the silicate interlayer in the range of 15.2-60.0 Å XRD d spacing. At the specific acidified ratio (H⁺/amine = 1/3 equiv ratio), the polyamine salts rendered the clay’s layered structure into randomization. The result was confirmed by using XRD and transmission electronic microscopy (TEM). The hybrids of polyamines and Mica or MMT were blended into epoxy resins and cured into nanocomposites, which exhibited the improvements of thermal stability and hardness.     

Simple and low-temperature synthesis of NiO nanoparticles through solid-state thermal decomposition of the hexa(ammine)Ni(II) nitrate, [Ni(NH3)6](NO3)2, complex

NiO nanoparticles with an average size of about 12 nm were easily prepared via the thermal decomposition of hexa(ammine)Ni(II) nitrate complex, [Ni(NH₃)₆](NO₃)₂, at low temperature of 250 °C. The product was characterized by thermal analysis (TGA/DTA), X-ray diffraction (XRD), Fourier-transformed infrared spectroscopy (FT-IR), UV-Vis spectroscopy, BET specific surface area measurement, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), and magnetic measurement. The magnetic measurement revealed a small hysteresis loop at room temperature, confirming a superparamagnetic (weak ferromagnetic) nature of the synthesized NiO nanoparticles. Indeed, the NiO nanoparticles prepared by this method could be an appropriate semiconductor material due to the optical band gap of 3.35 eV which shows a red shift in comparison with the previous reports. This method is simple, fast, safe, low-cost and also suitable for industrial production of high purity NiO nanoparticles for applied purposes.     

Chemical synthesis of mesoporous CuO from a single precursor: Structural, optical and electrical properties

We report a simple method for growing photoluminescent mesoporous CuO nanoparticles by a chemical route, using the single precursor technique. The final products were characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), N₂ adsorption-desorption isotherm, UV-vis absorption spectroscopy, photoluminescence (PL) spectroscopy, Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy and Hall measurements. Structural analysis reveals that the average pore diameter of the as-prepared CuO is about 38.8 Å and it comes with an average surface area of 66.63 m²/g. N₂-sorption analysis shows that the resulting isotherm as type IV; which is the characteristic of mesoporous materials. The average crystal diameter, as derived from the XRD data analysis is found to be about 20 nm. FESEM measurement reveals that the material is composed of cubic nanoparticles. The UV-vis spectrum of the material shows significant amount of blue-shift in the band gap energy (E_g), due to the quantum confinement effect exerted by the nanocrystals. The Raman study of the CuO nanostructures also indicates the high crystalline nature of the material. From the positive sign of Hall coefficient, the p-type conduction nature of the deposited film is established. The film was found to show high magnetoresistance, which is in the order of 10⁵ Ω.     

Synthesis of Mn3O4 nanoparticles by thermal decomposition of a [bis(salicylidiminato)manganese(II)] complex

The present investigation reports on the novel synthesis of Mn₃O₄ nanoparticles using thermal decomposition and their physicochemical characterization. The Mn₃O₄ nanoparticle powder has been prepared using [bis(salicylidiminato)manganese(II)] as a precursor. The effect of oleyl amine and triphenylphosphine on the particle morphology has been investigated. Transmission electron microscopy (TEM) analysis demonstrated Mn₃O₄ nanoparticles with an average diameter of about 25 nm. The structural study by X-ray diffraction (XRD) indicates that these nanoparticles have a pure tetragonal phase. The phase pure samples were characterized using X-ray photoelectron spectroscopy (XPS) for both Mn 2p and Mn 3s levels. The values of binding energies are consistent with related values reported in the literature.     

Decoration of carbon nanotubes with iron oxide

A magnetic composite of multiwalls carbon nanotubes (MWNTs) decorated with iron oxide nanoparticles was synthesized successfully by a simple and effective chemistry precipitation method. The composite was characterized by X-ray diffraction analysis (XRD), Mössbauer spectrum (MS), transmission electron microscopy (TEM), and Fourier transform spectroscopy (FTIR) techniques. The patterns of XRD and MS indicated that MWNTs, γ-Fe₂O₃, and Fe₃O₄ coexisted in the composite. The TEM observation indicated that the nanoparticles of iron oxide were attached on the surface of the MWNTs, and the sizes of the particles ranged from 25 to 80 nm. FTIR spectra showed that SO₄⁻ functional groups existed on the surface of MWNTs after modification by sodium dodecylbenzene sulfonic acid (SDBS), which could immobilize Fe³⁺ ions onto the MWNTs. The hysteresis loops of the MWNTs and decorated MWNTs were measured by vibrating sample magnetometer (VSM), and the results showed that the composite was ferromagnetism with the saturated magnetization of 20.07 emu/g, and the coercive of 163.44 Oe.     

A novel chelating acid-assisted thermolysis procedure for preparation of tin oxide nanoparticles

Pure tin dioxide (SnO₂) nanoparticles were synthesized via thermolysis of tin phthalate and tin oxalate in the presence of oleic acid (OA) as solvent. Oleic acid (OA) was employed as an organic solvent, which can be applied to control particle growth and to stabilize the particles. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL) spectroscopy. The orthorhombic phase SnO₂ nanoparticles with average size about 12 nm were synthesized through thermolysis of tin phthalate in the presence of oleic acid.     

Photocatalytic activity of ZrO2 nanoparticles prepared by electrical arc discharge method in water

ZrO₂ nanoparticles were synthesized through arc discharge of zirconium electrodes in deionized (DI) water. X-ray diffraction (XRD) analysis of the as prepared nanoparticles indicates formation a mixture of nanocrystalline ZrO₂ monoclinic and tetragonal phase structures. Transmission electron microscopy (TEM) images illustrate spherical ZrO₂ nanoparticles with 7–30 nm diameter range, which were formed during the discharge process with 10 A arc current. The average particle size was found to increase with the increasing arc current. X-ray photoelectron spectroscopy (XPS) analysis confirms formation of ZrO₂ at the surface of the nanoparticles. Surface area of the sample prepared at 10 A arc current, measured by BET analysis, was 44 m²/g. Photodegradation of Rhodamine B (Rh. B) shows that the prepared samples at lower currents have a higher photocatalytic activity due to larger surface area and smaller particle size.     

Synthesis and characterizations of anion exchange organic-inorganic hybrid materials based on poly(2,6-dimethyl-1,4-phenylene oxide) (PPO)

A series of poly(2,6-dimethyl-1,4-phenylene oxide) (PPO)-based organic-inorganic hybrid materials for anion exchange were prepared through sol-gel process of polymer precursors PPO-Si(OCH₃)₃. PPO-Si(OCH₃)₃ were obtained from the reaction of bromomethylated PPO with 3-aminopropyl-trimethoxysilane (A1110). These polymer precursors then underwent hydrolysis and condensation with additional A1110 to generate hybrid materials. The reaction to produce polymer precursors was identified by FTIR; while FTIR, TGA, XRD, SEM, as well as conventional ion exchange capacity (IEC) measurements were conducted for the structures and properties of the prepared hybrids. TGA results show that this series of hybrid materials possess high thermal stability; XRD and SEM indicate that the prepared hybrid materials are amorphous and the inorganic and organic contents show good compatibility if the ratio between them is proper. The IEC values of the hybrid materials due to the amine groups range from 1.13 mmol/gBPPO (material i) to 4.80 mmol/gBPPO (material iv).     

Alpha-particle-induced luminescence of rare-earth-doped Y2O3 nanophosphors

The feasibility of utilizing Y₂O₃:Tb³⁺ and Y₂O₃:Eu³⁺ as radioluminescent nanophosphors under alpha-particle excitation is investigated. Materials synthesized by the urea homogeneous precipitation method were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The XRD analysis of as-produced precipitates and nanophosphors fired at temperatures ranging from 950 to 1100 °C indicated the presence of highly crystalline cubic Y₂O₃ with crystallite sizes of ∼40 nm. SEM and TEM analysis revealed that particles with average diameters of ∼200 nm and comprised of ∼40 nm grains were obtained. High-resolution radioluminescence and photoluminescence spectra were used to investigate the unwanted radioluminescence saturation effects associated with the high ionization rate of alpha-particles. Additionally, the radioluminescence intensity as a function of rare-earth ion dopant concentration is investigated for these materials under alpha-particle excitation. The prospect for utilizing these materials as intermediate absorbers in indirect-conversion radioisotope batteries is discussed.     

Synthesis of maghemite sub-microspheres by simple solvothermal reduction method

Maghemite sub-micrometer-sized spheres were successfully prepared by a simple solvothermal reduction route at relatively low temperature. The as-obtained sample was characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), electron diffraction (ED), X-ray photoelectron spectroscopy (XPS) and superconducting quantum interference device (SQUID) measurements. XRD and XPS analyses indicate the formation of γ-Fe₂O₃ phase. TEM results reveal that the γ-Fe₂O₃ particles are spherical with the diameter of 200-400 nm. Magnetic measurements show that the Curie temperature of γ-Fe₂O₃ sub-microspheres is over 400 K and the sample exhibits ferromagnetic behavior at room temperature. It is found that the sub-microspheres possess high saturation magnetization of 81 emu/g at 300 K.