Annealing effects on the structure, photoluminescence, and magnetic properties of GaN/Mn3O4 core-shell nanowires

Nanowires consisting of GaN/Mn₃O₄ were prepared using a two-step approach that involved dipping the as-synthesized GaN nanowires into an aqueous manganese acetate solution. To examine the effects of annealing, GaN/Mn₃O₄ core-shell nanowires were heated thermally to 700 °C in N₂ ambient. Transmission electron microscopy showed that the continuous Mn₃O₄ shell layer had agglomerated to expose a bare GaN core surface after thermal annealing. The magnetic measurements showed that the ferromagnetic behavior of the GaN nanowires had been suppressed by coating with the Mn₃O₄ shell, without significant change by the subsequent thermal annealing. The GaN/Mn₃O₄ core-shell nanowires exhibited blue, green, and red photoluminescence (PL) emission. The red emission was enhanced by thermal annealing. This paper discusses the associated mechanism for the variations in PL and magnetic properties of GaN/Mn₃O₄ core-shell nanowires.     

Structure and phase composition of nanocrystalline Ce1−xLuxO2−y

The microstructure and phase stability of nanocrystalline mixed oxide Lu_xCe_1−xO_2−y (x=0-1) are described. Nano-sized (3-4 nm) oxide particles were prepared by the reverse microemulsion method. Morphological and structural changes upon heat treatment in an oxidizing atmosphere were studied by transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman and Yb³⁺ emission spectroscopy, the latter ion being present as an impurity in the Lu₂O₃ starting material. Up to 950 °C, the samples were single phase, with structure changing smoothly with Lu content from fluorite type (F) to bixbyite type (C). For the samples heated at 1100 °C phase separation into coexisting F- and C-type structures was observed for 0.35<x<0.7. It was also found that addition of Lu strongly hinders the crystallite growth of ceria during heat treatment at 800 and 950 °C.     

The solid state reaction between lanthanum oxide and strontium carbonate

The reaction between lanthanum oxide and strontium carbonate was studied non-isothermally between 350 and 1150 °C at different heating rates, intermediates and the final solid product were characterized by X-ray diffractometry (XRD). The reaction proceeds through formation of lanthanum oxycarbonate La₂O(CO₃)₂, lanthanum dioxycarbonate La₂O₂CO₃, and non-stoichiometric strontium lanthanum oxide La₂SrO_x (x = 4 + δ). La₄SrO₇ was found to be the final product which begins to form at ∼700 °C. Li⁺ doping enhances the formation of the final product as well as commencement of the reactions at lower temperatures.     

Sol-Gel Preparation of Fast Proton-Conducting P2O5-SiO2 Glasses

We have investigated the proton conductivities of the sol-gel-derived P₂O₅-SiO₂ glass at –50 to 120°C. The obtained glass is porous, where the surface area, pore volume and pore diameter are 740 m²/g, 0.5 cm³/g and <5 nm, respectively. The freezing temperature of water molecules adsorbed in the pores was –20°C, which is much lower than that of free liquid water due to the quantum size effect of the water confined in the pores. The electrical conductivities followed the Arrhenius equation in the temperatures between –20 and 120°C. Below –20°C, the adsorbed-water molecules were frozen, resulting in a rapid decrease of the proton conductivity. Considering the high conductivity, chemical and thermal stability, this oxide glass membranes have potential for the fuel cell membrane.     

GaN taper rods: Solid-phase synthesis, crystal defects, and optical properties

Wurtzite GaN taper rods assembled from highly oriented nanoparticles were synthesized using NaNH₂ and the as-synthesized GaOOH prismatic rods as reactants at 600 °C for 5 h. The lengths of the GaN taper rods are in the range of 4–6 μm and the diameters are about 0.5–1.5 μm. It was found that a slow heating rate (1 °C min⁻¹) was beneficial to keeping the one-dimensional (1D) skeleton of GaN, otherwise only GaN nanoparticles were obtained with a quick heating rate (10 °C min⁻¹). Selected area electron diffraction (SAED) patterns and high-resolution transmission electron microscopy (HRTEM) observations revealed that the GaN taper rods assembled from highly oriented nanoparticles and there were crystal defects in the GaN structure. The GaN taper rods displayed luminescence emission in the blue-violet region, which may be related to crystal defects.     

The formation and physicochemical characterization of Al2O3-doped manganese ferrites

Mn/Fe mixed oxide solids doped with Al₂O₃ (0.32-1.27 wt.%) were prepared by impregnation of manganese nitrate with finely powdered ferric oxide, then treated with different amounts of aluminum nitrate. The obtained samples were calcined in air at 700-1000 °C for 6 h. The specific surface area (S_BET) and the catalytic activity of pure and doped precalcined at 700-1000 °C have been measured by using N₂ adsorption isotherms and CO oxidation by O₂. The structure and the phase changes were characterized by DTA and XRD techniques. The obtained results revealed that Mn₂O₃ interacted readily with Fe₂O₃ to produce well-crystallized manganese ferrite (MnFe₂O₄) at temperatures of 800 °C and above. The degree of propagation of this reaction increased by Al₂O₃-doping and also by increasing the heating temperature. The treatment with 1.27 wt.% Al₂O₃ followed by heating at 1000 °C resulted in complete conversion of Mn/Fe oxides into the corresponding ferrite phase. The catalytic activity and S_BET of pure and doped solids were found to decrease, by increasing both the calcination temperature and the amount of Al₂O₃ added, due to the enhanced formation of MnFe₂O₄ phase which is less reactive than the free oxides (Mn₂O₃ and Fe₂O₃). The activation energy of formation (ΔE) of MnFe₂O₄ was determined for pure and doped solids. The promotion effect of aluminum in formation of MnFe₂O₄ was attributed to an effective increase in the mobility of reacting cations.     

Solid-solid interactions in pure and Li2O-doped manganese and magnesium mixed oxides system

The solid-solid interactions between manganese and magnesium oxides in absence and in presence of small amounts of Li₂O have been investigated. The molar ratios between manganese and magnesium oxides in the form of Mn₂O₃ and MgO were varied between 0.05:1 to 0.5:1. The mixed solids were calcined in air at 400-1000°C. The techniques employed were DTA, XRD and H₂O₂ decomposition at 20-40°C.The results obtained revealed that solid-solid interactions took place between the reacting solids at 600-1000°C yielding magnesium manganates (Mg₂MnO₄, Mg₆MnO₈, MgMnO₄ besides unreacted portions of MgO, Mn₂O₃ and Mn₃O₄). Li₂O-doping (0.75-6 mol%) of the investigated system followed by calcination at 600 and 800°C decreased progressively the intensity of the diffraction lines of Mn₂O₃ (Bixbyite) with subsequent increase in the lattice parameter 'a' of MgO to an extent proportional to the amount of Li₂O added. This finding might suggest that the doping process enhanced the dissolution of Mn₂O₃ in MgO forming solid solution. This treatment led also to the formation of Li₂MnO₃. Furthermore, the doping with 3 and 6 mol% Li₂O conducted at 800°C resulted in the conversion of Mn₂O₃ into Mn₃O₄, a process that took place at 1000°C in absence of Li₂O. The produced Li₂MnO₃ phase remained stable by heating at up to 1000°C. Furthermore, Li₂O doping of the investigated system at 400-1000°C resulted in a progressive measurable increase in the particle size of MgO.The catalytic activity measurements showed that the increase in the molar ratio of Mn₂O₃ in the samples precalcined at 400-800°C was accompanied by a significant increase in the catalytic activity of the treated solids. The maximum increase in the catalytic activity expressed as reaction rate constant measured at 20°C (k _20°C) attained 3.14, 2.67 and 3.25-fold for the solids precalcined at 400, 600 and 800°C, respectively. Li₂O-doping of the samples having the formula 0.1 Mn₂O₃/MgO conducted at 400-600°C brought a progressive significant increase in its catalytic activity. The maximum increase in the value of k _20°C due to Li₂O attained 1.93 and 2.75-fold for the samples preheated at 400 and 600°C, respectively and opposite effect was found for the doped samples preheated at 800°C.This revised version was published online in November 2005 with corrections to the Cover Date.     

Temperature-dependent structural study of microporous CsAlSi5O12

CsAlSi₅O₁₂ crystals were synthesized at high temperature by slow cooling of a vanadium oxide flux. Single-crystal X-ray diffraction structure analysis and electron microprobe analyses yielded the microporous CAS zeolite framework structure of Cs_0.85Al_0.85Si_5.15O₁₂ composition. High-temperature single-crystal and powder X-ray diffraction studies were utilized to analyze anisotropic thermal expansion. Rietveld refined cell constants from powder diffraction data, measured in steps of 25 °C up to 700 °C, show a significant decrease in expansion above 500 °C. At 500 °C, a displacive, static disorder-dynamic disorder-type phase transition from the acentric low-temperature space group Ama2 to centrosymmetric Amam (Cmcm in standard setting) was found. Thermal expansion below the phase transition is governed by rigid-body TO₄ rotations accompanied by stretching of T-O-T angles. Above the phase transition at 500 °C all atoms, except one oxygen (O6), are fixed on mirror planes. Temperature-dependent polarized Raman single-crystal spectra between −270 and 300 °C and unpolarized spectra between room temperature and 1000 °C become increasingly less resolved with rising temperature confirming the disordered static-disordered dynamic type of the phase transition.     

Application of Alumina Aerogels as Catalysts

Al₂O₃ gels prepared by hydrolysis of Al-alkoxide were applied as catalysts for NO reduction by hydrocarbon. Xerogels were obtained by drying at 90°C, for 24 h, in air. Aerogels were prepared by supercritical drying of the wet gels in ethanol, using an autoclave. The catalyst activity of the gels for NO reduction with C₃H₆ as determined at 200–600°C in a fixed bed flow reactor. NO conversion to N₂ was about 60% at 550°C with both catalysts, and at 600°C it was better with the aerogel than with the xerogel. The specific surface area of the xerogel, which was larger than that of the aerogel as-dried, decreased to 1/3 by annealing at >500°C. However, the surface area of the aerogel hardly changed by annealing at temperatures up to 700°C. The bimodal pore size distribution of the aerogel hardly changed by annealing, too. The microstructure of the aerogels is stable at high temperatures, and they are better catalysts at high temperatures.     

Preparation of La0.75Sr0.25MnO3 Nano-Phase Powders and Films from Alkoxide Precursors

The first purely alkoxide-based sol-gel route to nano-phase powders and thin films of perovskite La_0.75Sr_0.25MnO₃ is described. The phase and microstructure evolution on heat treatment of free gel films to form the target nano-phase oxide were investigated by TGA, IR spectroscopy, powder XRD, SEM and TEM-EDS. The xerogel consisted of a hydrated oxo-carbonate, without remaining alkoxo groups or solvent. Heating at 5°C·min^–1 decomposed the carbonate groups and yielded the pure perovskite La_0.75Sr_0.25MnO₃ at 760°C. The cell dimensions were virtually unchanged from the first observation of perovskite at 680°C, to 1000°C, 4 h. The monoclinic cell of La_0.75Sr_0.25MnO₃ obtained at 1000°C, 4 h, had the dimensions a = 5.475(1), b = 5.504(2), c = 7.771(1) Å, = 90.50(2), fitting the literature data quite well. Crack-free, homogenous, 150 nm thick La_0.75Sr_0.25MnO₃ films were prepared by spin-coating Si/SiO₂/TiO₂/Pt and polycrystalline -Al₂O₃ substrates with a 0.6 M alkoxide solution, followed by heating at 5°C·min^–1 to 800°C, 30 min.     

Mesoporous Nb2O5 Films: Influence of Degree of Crystallinity on Properties

Nanocrystalline Nb₂O₅ films were prepared by an extended sol-gel method. The synthesis is based on the hydrolysis of a modified Nb-alkoxide precursor. Reaction of the modified precursor (Nb(OEt)₅ + 2 2,4-pentanedione) with water in ethanol leads to a homogeneous hydrolyzed solution, which is stable against precipitation of niobium oxide after evaporation of the ethanol and in the whole pH-range investigated (1–10). Autoclaving leads to amorphous gels, from which homogeneous nanocrystalline niobium oxide films of up to 15 m can be made. During annealing crystalline phases are first observed above 500°C with fully crystalline films of orthorhombic T-phase Nb₂O₅ attained at 600°C. The microstructural, crystallographic, optical and photoelectrical properties of the films were characterized by means of SEM, XRD, UV-VIS spectroscopy and surface photovoltage spectroscopy, respectively.     

Photoluminescent BaMoO4 nanopowders prepared by complex polymerization method (CPM)

The BaMoO₄ nanopowders were prepared by the Complex Polymerization Method (CPM). The structure properties of the BaMoO₄ powders were characterized by FTIR transmittance spectra, X-ray diffraction (XRD), Raman spectra, photoluminescence spectra (PL) and high-resolution scanning electron microscopy (HR-SEM). The XRD, FTIR and Raman data showed that BaMoO₄ at 300 °C was disordered. At 400 °C and higher temperature, BaMoO₄ crystalline scheelite-type phases could be identified, without the presence of additional phases, according to the XRD, FTIR and Raman data. The calculated average crystallite sizes, calculated by XRD, around 40 nm, showed the tendency to increase with the temperature. The crystallite sizes, obtained by HR-SEM, were around of 40-50 nm. The sample that presented the highest intensity of the red emission band was the one heat treated at 400 °C for 2 h, and the sample that displayed the highest intensity of the green emission band was the one heat treated at 700 °C for 2 h. The CPM was shown to be a low cost route for the production of BaMoO₄ nanopowders, with the advantages of lower temperature, smaller time and reduced cost. The optical properties observed for BaMoO₄ nanopowders suggested that this material is a highly promising candidate for photoluminescent applications.     

Influence of the crystallinity on the Li+ intercalation process in Nb2O5 films

Nb₂O₅ thin films were prepared by the Pechini method. The effect of the film crystallinity on the electrochemical and electrochromic properties was investigated. A relationship between the crystalline structure and the Li⁺ intercalation/extraction process, stability and kinetics was observed. A significant decrease in the electrochemical response was observed as a function of the number of cycles for films treated at 400 and 450 °C. However, as the calcination temperature increases this effect disappears. XRD studies shown that at 400 °C, the material is amorphous, evolving to orthorhombic phase. The transmittance variation as well as the coloration efficiency increases as the temperature is increased. In the initial cycles the intercalation charge is higher for the amorphous oxide than for the orthorhombic phase. However, the variation in the optical density is small. On the other hand, the charge of the orthorhombic phase oxide does not change. These results suggest that there are two different processes associated with Li⁺ intercalation, but only one of them leads to the coloration process.     

Hydrogen production from water decomposition by redox of Fe2O3 modified with single- or double-metal additives

Iron oxide modified with single- or double-metal additives (Cr, Ni, Zr, Ag, Mo, Mo-Cr, Mo-Ni, Mo-Zr and Mo-Ag), which can store and supply pure hydrogen by reduction of iron oxide with hydrogen and subsequent oxidation of reduced iron oxide with steam (Fe₃O₄ (initial Fe₂O₃)+4H₂↔3Fe+4H₂O), were prepared by impregnation. Effects of various metal additives in the samples on hydrogen production were investigated by the above-repeated redox. All the samples with Mo additive exhibited a better redox performance than those without Mo, and the Mo-Zr additive in iron oxide was the best effective one enhancing hydrogen production from water decomposition. For Fe₂O₃-Mo-Zr, the average H₂ production temperature could be significantly decreased to 276 °C, the average H₂ formation rate could be increased to 360.9-461.1 μmol min⁻¹ Fe-g⁻¹ at operating temperature of 300 °C and the average storage capacity was up to 4.73 wt% in four cycles, an amount close to the IEA target.     

Preparation and Characterization of SiO2-MxOy(M = V, Sn, Sb) Thin Films from Silicic Acid and Metal Chlorides

The preparation of SiO₂-M _x O _y (M = V, Sn, Sb) binary oxide thin films by sol-gel method was investigated. The reaction of silicic acid with metal chloride (M = Sn and Sb) or oxychloride (M = V) formed homogeneous solutions. The dip-coating of slide glass and silicon wafer followed by heat treatment gave oxide films having Si—O—M bond. The changes of FT-IR spectra as a function of heat treatment temperature and molar composition confirmed the Si—O—M bonds. The sheet resistance of films increased with an increase on heat treatment temperature and decrease in the content of metal oxide M _x O _y . X-ray diffraction peaks were observed for the SiO₂-V₂O₅ films with high V₂O₅ contents and heat-treated above 250°C, while the others were amorphous. Oxide films heat treated at 500°C had a thickness between 340–470 nm.     

Optical Properties of Mg x Zn1−x O Polycrystalline Thin Films Prepared by Sol-Gel Deposition Method

The Mg _x Zn_1–x O alloy thin films were synthesized on Si and quartz substrates by the sol-gel deposition method. The transmittance and cathodoluminescence spectra of the Mg_0.05Zn_0.95O and Mg_0.15Zn_0.85O nanoparticle films were obtained at room temperature. It was found that the bandgap of Mg_0.05Zn_0.95O and Mg_0.15Zn_0.85O films is as large as 3.72 eV and 3.79 eV, respectively. The ultraviolet emission peaks are located at 376 nm and 370 nm, respectively, for the samples annealed at 600°C. When the annealing temperature is elevated to 1000°C, the band-gap decreases to 3.42 eV and an emission line related to the deep-level defect appears at 500 nm. The mechanism behind these phenomena is discussed.     

Hydrothermal synthesis of cobalt carbonates using different counter ions: An efficient precursor to nano-sized cobalt oxide (Co3O4)

Synthesis of submicrometer crystalline particles of cobalt carbonate was achieved hydrothermally using different cobalt salts and urea with a molar ratio from 1:3 to 1:20 (cobalt salt:urea) in aqueous solutions at 160 °C for 24-36 h, in the presence of cetyltrimethylammonium bromide (CTAB) as a surfactant. Nanoparticles of Co₃O₄, with an average size from 30 to 39 nm, were obtained by thermal decomposition of CoCO₃ samples at 500 °C for 3 h in an electrical furnace. The as-synthesized products were characterized by powder X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), UV-Vis spectra and thermal analysis. Studying the optical properties of the as-prepared cobalt oxide nanoparticles showed the presence of two band gaps, the values of which confirmed the semiconducting properties of the prepared Co₃O₄.     

Nano Fe3O4 as magnetically recyclable catalyst for the synthesis of α-aminophosphonates in solvent-free conditions

The three component, one-pot synthesis of α-aminophosphonates has been achieved using super magnetic nano iron oxide at 50 °C under solvent-free conditions in excellent yields. The major advantages of the present method are high yields, short reaction times, magnetically recyclable catalyst, and solvent-free reaction conditions.     

Insights into photoluminescence property and photocatalytic activity of cubic and rhombohedral ZnIn2S4

Cubic and rhombohedral ZnIn₂S₄ were synthesized by thermal sulfidation of Zn-In mixed oxide precursor in H₂S atmosphere at different temperatures. Cubic ZnIn₂S₄ was obtained when Zn-In mixed oxide precursor was sulfurized at 400 °C. With sulfidation temperature increasing from 400 to 800 °C, the crystal phase of ZnIn₂S₄ gradually turned from cubic to rhombohedral, which was demonstrated by different analysis techniques such as XRD, Raman, SEM, etc. UV-vis absorption spectra indicated that cubic ZnIn₂S₄ displayed better light absorption property than rhombohedral ZnIn₂S₄, with band gaps calculated to be 2.0 and 2.5 eV, respectively. However, under visible light irradiation, rhombohedral ZnIn₂S₄ photocatalyzed H₂ evolution from aqueous sodium sulfite/sulfide solution efficiently, whereas cubic ZnIn₂S₄ was not active for this reaction. The photoluminescence property revealed the different dynamics of photogenerated carriers, which made a predominant contribution to the increasing photocatalytic performances of ZnIn₂S₄ with crystal phase turning from cubic to rhombohedral.     

Time-Dependent Degradation Due to the Gradual Phase Change in BICUVOX and BICOVOX Oxide-Ion Conductors at Temperatures below about 500°C

This paper describes a cause of the time-dependent degradation of conductivity observed in the representative BIMEVOX phases Bi₂Cu_0.1V_0.9O_5.35 (BICUVOX.10) and Bi₂Co_0.1V_0.9O_5.35 (BICOVOX.10). In both phases, to date, the following facts were reported: the high-temperature stable γ-type phase transformed reversibly to the low-temperature stable γ′-type phase at 450-500°C through the order-disorder transition without changing to the β-type or α-type phase. In addition, the degradation of conductivity was observed in γ′-BICUVOX.10 at about 420°C. In the present study, it has turned out that a prolonged annealing at 450°C for several hundred hours causes both γ′ phases to change to a new phase with α-Bi₄V₂O₁₁-related structure. This α-related phase changes promptly to the γ phase on heating (at about 535°C for BICOVOX.10 and at about 485°C for BICUVOX.10); by contrast, the γ′ phase reverts sluggishly to the α-related phase. Since the α-related phase shows far lower conductivity (10^−4.8S cm⁻¹ at 430°C for BICUVOX.10), this gradual γ′-to-α transition explains well the time-dependent degradation of conductivity in the γ′ phase reported so far. Namely, the γ′ phase is metastably quenched to room temperature and reverts gradually to the α-related phase upon heat treatment below the α-to-γ transition temperature.