La0.6Sr1.4MnO4 layered perovskite anode material for intermediate temperature solid oxide fuel cells

La_0.6Sr_1.4MnO₄ (LSMO₄) layered perovskite with K₂NiF₄ structure was prepared and evaluated as anode material for La_0.8Sr_0.2Ga_0.83Mg_0.17O_3 − δ (LSGM) electrolyte supported intermediate temperature solid oxide fuel cells (IT-SOFCs). X-ray diffraction results show that LSMO₄ is redox stability. Thermal expansion coefficient of LSMO₄ is close to that of LSGM electrolyte. By adopting LSMO₄ as anode and La_0.6Sr_0.4Co_0.8Fe_0.2O₃ (LSCF) as cathode, maxium power densities of 146.6, 110.9 mW cm^− 2 with H₂ fuel at 850, 800 °C and 47.3 mW cm^− 2 with CH₄ fuel at 800 °C were obtained, respectively. Further, the cell demonstrated a reasonably stable performance under 180 mA cm^− 2 for over 40 h with H₂ fuel at 800 °C.     

Hexaferrites and phase relations in the iron-rich part of the system Sr-La-Co-Fe-O

The iron rich part of the system was examined in the temperature range of 1200-1380 °C in air, with focus on the solid solutions of M-type hexaferrites. Samples of suitable compositions were studied by electronprobe microanalysis (EPMA). Substituted Sr-hexaferrites in the system Sr-La-Co-Fe-O do not follow the 1:1 substitution mechanism of La/Co in M-type ferrites. Due to the presence and limited Co²⁺-incorporation Fe³⁺-ions are reduced to Fe²⁺ within the crystal lattice to obtain charge balance. In all examined M-type ferrites divalent iron is formed, even at 1200 °C. The substitution principle Sr²⁺+Fe³⁺↔La³⁺+(Fe²⁺, Co²⁺) yields to the general substitution formula for the M-type hexaferrite Sr²⁺_1-xLa³⁺_xFe²⁺_x-yCo²⁺_yFe³⁺_12-xO¹⁹ (0≤x≤1 and 0≤y≤x). In addition Sr/La-perovskite_SS (_SS=solid solution), Co/Fe-spinel_SS, hematite and magnetite are formed. Sr-hexaferrite exhibits at 1200 °C a limited solid solution with small amounts of Fe²⁺ (SrFe₁₂O₁₉↔Sr_0.3La_0.7Co_0.5Fe²⁺_0.2Fe_11.3O₁₉). At 1300 and 1380 °C a continuous solid solution series of the M-type hexaferrite is stable. SrFe₁₂O₁₉ and LaCo_0.4Fe²⁺_0.6Fe₁₁O₁₉ are the end members at 1300 °C. The maximum Fe²⁺O content is about 13 mol% in the M-type ferrite at 1380 °C (LaCo_0.1Fe²⁺_0.9Fe₁₁O₁₉).     

Phase equilibria and crystal structure of the complex oxides in the Sr-Fe-Co-O system

Phase relations in the Sr-Fe-Co-O system have been investigated at 1100 °C in air by X-ray powder diffraction on quenched samples. Solid solutions of the form SrFe_1−xCo_xO_3−δ (0?x?0.7), Sr₃Fe_2−yCo_yO_7−δ (0?y?0.4) and Sr₄Fe_6−zCo_zO_13±δ (0?z?1.6) were prepared by solid-state reaction and by the sol-gel method. The structural parameters of single-phase samples were refined by the Rietveld profile method. The variation of the lattice parameters with composition has been determined for each solid solution and a cross-section of the phase diagram at 1100 °C in air for the entire Sr-Fe-Co-O system has been constructed.     

Synthesis, Crystal and Magnetic Structures of the Sodium Ferrate (IV) Na4FeO4 Studied by Neutron Diffraction and Mössbauer Techniques

The alkali sodium ferrate (IV) Na₄FeO₄ has been prepared by solid-state reaction of sodium peroxide Na₂O₂ and wustite Fe_1−xO, in a molar ratio Na/Fe=4, at 400°C under vacuum. Powder X-ray and neutron diffraction studies indicate that Na₄FeO₄ crystallizes in the triclinic system P−1 with the cell parameters= a=8.4810(2) Å, b=5.7688(1) Å, c=6.5622(1) Å, α=124.662(2)°, β=98.848(2)°, γ=101.761(2)° and Z=2. Na₄FeO₄ is isotypic with the other known phases Na₄MO₄ (M=Ti, Cr, Mn, Co and Ge, Sn, Pb). The solid solution Na₄Fe_xCo_1−xO₄ exists for x=0-1 and we have followed the evolution of the cell parameters with x to determine the lattice parameters of the triclinic cell of Na₄FeO₄. A three-dimensional network of isolated FeO₄ tetrahedra connected by Na atoms characterizes the structure. This compound is antiferromagnetic below T_N=16 K. At 2 K the magnetic cell is twice the nuclear cell and the magnetic structure is collinear (μ_Fe=3.36(12) μ_B at 2 K). This black compound is highly hygroscopic. In water or on contact with the atmospheric moisture it is disproportionated in Fe³⁺ and Fe⁶⁺. The Mössbauer spectra of Na₄FeO₄ are fitted with one doublet (δ=− 0.22 mm/s, Δ=0.41 mm/s at 295 K) in the paramagnetic state and with a sextet at 8K. These parameters characterize Fe⁴⁺ high-spin in tetrahedral FeO₄ coordination.     

Co3−δO4 paracrystal: 3D assembly of nanosize defect clusters in spinel lattice

Paracrystalline array of defect clusters ca. five times the lattice spacing of the average Co_3−δO₄ spinel structure occurred more or less in a relaxed manner when the sintered Co_1−xO polycrystals were air-quenched below the Co_1−xO/Co_3−δO₄ transition temperature to activate oxy-precipitation of cube-like Co_3−δO₄ at dislocations. The same paracrystalline spacing was obtained for Co_3−δO₄ when formed via oxidizing/sintering the Co_1−xO powders at 800°C in air, suggesting a nearly constant δ value for Co_3−δO₄ in the T-P_O2 conditions encountered. The extra cobalt vacancies and Co³⁺ interstitials, as a result of δ value, may form additional 4:1-derived defect clusters for further paracrystalline distribution in the spinel lattice. The nanosize defect clusters self-assembled by columbic interactions and lattice relaxation in ionic crystal may have potential applications as step-wise sensor of oxygen partial pressure at high temperatures.     

A new 2212-type stair like structure: Bi14Sr21Fe12O61, m=5 member of the generic [Bi2Sr3Fe2O9]m[Bi4Sr6Fe2O16] family

A new oxide, Bi₁₄Sr₂₁Fe₁₂O_61, with a layered structure derived from the 2212 modulated type structure Bi₂Sr₃Fe₂O₉, was isolated. It crystallizes in the I2 space group, with the following parameters: a=16.58(3) Å, b=5.496(1) Å, c=35.27(2) Å and β=90.62°. The single crystal X-ray structure determination, coupled with electron microscopy, shows that this ferrite is the m=5 member of the [Bi₂Sr₃Fe₂O₉]_m[Bi₄Sr₆Fe₂O₁₆] collapsed family. This new collapsed structure can be described as slices of 2212 structure of five bismuth polyhedra thick along , shifted with respect to each other and interconnected by means of [Bi₄Sr₆Fe₂O₁₆] slices. The latter are the place of numerous defects like iron or strontium for bismuth substitution; they can be correlated to intergrowth defects with other members of the family.     

Structural properties of LaxSr2−xFeO4±δ at high temperature and under reducing conditions

A series of materials, La_xSr_2−xFeO_4±δ (x=0.6-1.0), have been investigated structurally using neutron and X-ray diffraction techniques as well as Mössbauer spectroscopy as a function of temperature and composition. These materials adopt the I4/mmm K₂NiF₄-type structure over a wide range of temperatures (25-1200°C) and oxygen stoichiometries. In particular, it was observed that at a critical composition of x>0.8 there was a significant shift in the lattice parameters. This was attributed to changes in the Fe³⁺ content and the resultant effect of this on the d_z² orbitals giving a lengthening of the Fe-O bonds. On heating, completely linear behavior in both the a and c cell constants was observed, masking underlying bond length changes.     

Thermodynamic studies on SrFe12O19(s), SrFe2O4(s), Sr2Fe2O5(s) and Sr3Fe2O6(s)

The citrate-nitrate gel combustion route was used to prepare SrFe₂O₄(s), Sr₂Fe₂O₅(s) and Sr₃Fe₂O₆(s) powders and the compounds were characterized by X-ray diffraction analysis. Different solid-state electrochemical cells were used for the measurement of emf as a function of temperature from 970 to 1151 K. The standard molar Gibbs energies of formation of these ternary oxides were calculated as a function of temperature from the emf data and are represented as (SrFe₂O₄, s, T)/kJ mol⁻¹ (±1.7)=−1494.8+0.3754 (T/K) (970?T/K?1151). (Sr₂Fe₂O₅, s, T)/kJ mol⁻¹ (±3.0)=−2119.3+0.4461 (T/K) (970?T/K?1149). (Sr₃Fe₂O₆, s, T)/kJ mol⁻¹ (±7.3)=−2719.8+0.4974 (T/K) (969?T/K?1150).Standard molar heat capacities of these ternary oxides were determined from 310 to 820 K using a heat flux type differential scanning calorimeter (DSC). Based on second law analysis and using the thermodynamic database FactSage software, thermodynamic functions such as Δ_fH°(298.15 K), S°(298.15 K) S°(T), C_p°(T), H°(T), {H°(T)-H°(298.15 K)}, G°(T), free energy function (fef), Δ_fH°(T) and Δ_fG°(T) for these ternary oxides were also calculated from 298 to 1000 K.     

Influence of electrospraying parameters on the microstructure of La0.6Sr0.4Co0.2F0.8O3−δ films for SOFCs

Ceramics can play a remarkable role in the engineering of intermediate temperature solid oxide fuel cells (IT-SOFCs) capable of meeting the ambitious targets of reduced cost and improved lifetime. While mixed ionic-electronic conductors such as La_xSr_1−xCo_yFe_1−yO_3−δ are being used as volumic cathodes to increase the catalytic performance of these components, adequate microstructures are also an important requirement for optimal performance, particularly at lower operating temperatures. This work is devoted to the fabrication of La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ films on Ce_0.9Gd_0.1O_2−δ substrates by electrostatic spray deposition (ESD) and to the characterization of the microstructural dependence on the deposition conditions. A wide variety of microstructures ranging from dense to porous, with particular features such as reticulation and micro-porosity, were obtained by varying the ESD deposition parameters: nozzle-to-substrate distance (15, 30, 43, 45, and 58 mm), solution flow rate (0.34 and 1.5 mL/h), and substrate temperature (300, 350, 400 and 450 °C). The correlation between deposition parameters and resulting microstructures was systematically studied and put into evidence.     

Investigation of the quasi-ternary system LaMnO3-LaCoO3-“LaCuO3”—I: the series La(Mn0.5Co0.5)1−xCuxO3−δ

The La(Mn_0.5Co_0.5)_1−xCu_xO_3−δ series with x=0, 0.05, 0.1, 0.2, 0.4, 0.6, 0.8 and 1 was synthesized by the Pechini method to obtain insight into the phase formation in the quasi-ternary LaMnO₃-LaCoO₃-“LaCuO₃” system caused by the instability of LaCuO₃ under ambient conditions. After sintering at 1100°C some remarkable results were obtained: LaMn_0.3Co_0.3Cu_0.4O_3−δ crystallized as a single phase in the orthorhombic perovskite structure typical of LaCuO₃. Among the synthesized compositions this compound showed the highest electrical conductivity in air at 800°C (155 S cm⁻¹) and also the highest thermal expansion coefficient (α_30−800°C=15.4×10⁻⁶ K⁻¹). The LaCuO_3−δ composition also crystallized as a single phase but in a monoclinic structure although previous investigations have shown that other phases are preferably formed after sintering at 1100°C. The electrical conductivity and thermal expansion coefficient were the lowest within the series of compositions, i.e. 9.4 S cm⁻¹ and 11.9×10⁻⁶ K⁻¹, respectively.     

LaxSr2−xFeyRu1−yO4±δ: a new family of K2NiF4 type oxides

The phases La_xSr_2−xFe_yRu_1−yO_4±δ (x=0.2-0.8; y=0.6-0.9) have been synthesized by solid-state techniques and yield tetragonal structures with I4/mmm symmetry. The oxygen stoichiometry and high-temperature structures have been examined using diffraction techniques and in situ Mössbauer spectroscopy at temperatures up to ∼600°C. Furthermore, new reduced phases that adopt structures with Immm symmetry have been discovered. Unusual coordination numbers have been determined for the most highly reduced samples with square planar coordination evident for the B site cations. The reduced orthorhombic Immm phases were found to readily reoxidize in air to the tetragonal I4/mmm structure at relatively low temperatures of only ∼500°C.     

Phase segregation in the Gd1−xSrxFeO3−δ series

Gd_1−xSr_xFeO_3−δ ferrites have been studied by means of X-ray powder diffraction in the whole composition range. Single-phase solid solution is found for x<0.09 and for x>0.63. At intermediate Sr content, phase segregation takes place. Compounds with x?0.05 crystallize in the orthorhombic structure, space group Pbnm. Oxygen-deficient Gd_1−xSr_xFeO_3−δ with x?2/3 are cubic or nearly cubic. The oxygen vacancies stabilize the cubic phase for x=2/3 whereas highly oxidized samples show an orthorhombic distortion, which has not been observed earlier. Magnetic and electrical properties have been measured for the single-phase solid solutions. Gd_1−xSr_xFeO_3−δ compounds with x?2/3 order antiferromagnetically below ∼100 K. In the paramagnetic region, their susceptibility follows the Curie-Weiss law in all but SrFeO_2.96 compound. These ferrites show semiconducting behavior in the electrical transport likely related to atomic disorder. We find that the conductivity activation energy becomes larger by increasing either the Gd content or the oxygen vacancies.     

Ion–electron transport in strontium ferrites: relationships with structural features and stability

The total electrical conductivity of strontium ferrites, including intergrowth Sr₄Fe₆O_13+δ, Sr₃Fe₂O_6+δ with a Ruddlesden–Popper structure, and SrFeO_2.5+δ where the cubic perovskite lattice transforms into vacancy-ordered brownmillerite at p(O₂)<10 Pa and T<850 °C, was measured at 650–1000 °C in the oxygen partial pressure range 10⁻¹⁵ Pa to 50 kPa. The data were used in order to determine partial ion, p- and n-type electron contributions in the vicinity of electron–hole equilibrium point. The ferrites with brownmillerite and Ruddlesden–Popper structures exhibit substantial ion transport due to thermally-activated disordering of oxygen vacancies and oxygen ions in the perovskite structural slabs, whereas the ion conductivity of Sr₄Fe₆O_13+δ remains below 0.01 S cm⁻¹ in the studied conditions. The bonding energy of oxygen ions, evaluated from the formation enthalpy of n-type charge carriers, increases in the sequence Sr₄Fe₆O_13+δ<SrFeO_3+δ<Sr₃Fe₂O_6+δ. These values correlate with thermodynamic stability of strontium ferrites at low p(O₂). The transition of SrFeO_2.5+δ brownmillerite into disordered cubic phase above 850 °C leads to higher stability in reducing atmospheres. The level of p-type conductivity is mainly governed by the concentration of electron holes, which was calculated from the oxygen content determined by coulometric titration technique. The hole mobility, which is quite similar for all strontium ferrites and has a temperature-activated character, varies in the range 0.005–0.05 cm² V⁻¹ s⁻¹ indicative of small-polaron conduction mechanism.     

The formation and physicochemical characterization of Al2O3-doped manganese ferrites

Mn/Fe mixed oxide solids doped with Al₂O₃ (0.32-1.27 wt.%) were prepared by impregnation of manganese nitrate with finely powdered ferric oxide, then treated with different amounts of aluminum nitrate. The obtained samples were calcined in air at 700-1000 °C for 6 h. The specific surface area (S_BET) and the catalytic activity of pure and doped precalcined at 700-1000 °C have been measured by using N₂ adsorption isotherms and CO oxidation by O₂. The structure and the phase changes were characterized by DTA and XRD techniques. The obtained results revealed that Mn₂O₃ interacted readily with Fe₂O₃ to produce well-crystallized manganese ferrite (MnFe₂O₄) at temperatures of 800 °C and above. The degree of propagation of this reaction increased by Al₂O₃-doping and also by increasing the heating temperature. The treatment with 1.27 wt.% Al₂O₃ followed by heating at 1000 °C resulted in complete conversion of Mn/Fe oxides into the corresponding ferrite phase. The catalytic activity and S_BET of pure and doped solids were found to decrease, by increasing both the calcination temperature and the amount of Al₂O₃ added, due to the enhanced formation of MnFe₂O₄ phase which is less reactive than the free oxides (Mn₂O₃ and Fe₂O₃). The activation energy of formation (ΔE) of MnFe₂O₄ was determined for pure and doped solids. The promotion effect of aluminum in formation of MnFe₂O₄ was attributed to an effective increase in the mobility of reacting cations.     

Transport properties and stability of Ni-containing mixed conductors with perovskite- and K2NiF4-type structure

The total conductivity and Seebeck coefficient of a series of Ni-containing phases, including La₂Ni_1−xM_xO_4+δ (M=Co, Cu; x=0.1-0.2) with K₂NiF₄-type structure and perovskite-like La_0.90Sr_0.10Ga_0.65Mg_0.15Ni_0.20O_3−δ and La_0.50Pr_0.50Ga_0.65Mg_0.15Ni_0.20O_3−δ, were studied in the oxygen partial pressure range from 10⁻¹⁸ Pa to 50 kPa at 973-1223 K. Within the phase stability domain, the conductivity of layered nickelates is predominantly p-type electronic and occurs via small-polaron mechanism, indicated by temperature-activated hole mobility and p(O₂) dependencies of electrical properties. In oxidizing conditions similar behavior is characteristic of Ni-containing perovskites, which exhibit, however, significant ionic contribution to the transport processes. The role of ionic conduction increases with decreasing p(O₂) and becomes dominant in reducing atmospheres. All nickelate-based phases decompose at oxygen pressures considerably lower with respect to Ni/NiO boundary. The partial substitution of nickel in La₂Ni(M)O_4+δ has minor effect on the stability limits, which are similar to that of La_0.90Sr_0.10Ga_0.65Mg_0.15Ni_0.20O_3−δ. On the contrary, praseodymium doping enhances the stability of La_0.50Pr_0.50Ga_0.65Mg_0.15Ni_0.20O_3−δ down to p(O₂) values as low as 10⁻¹⁷-10⁻¹⁰ Pa at 1023-1223 K.     

Thermochemistry of La0.7Sr0.3Mn1−xFexO3 solid solutions (0<x<1)

The structure, the energetics and the internal redox reactions of La_0.7Sr_0.3Fe_xMn_1−xO₃ have been studied in the complete solid solution range 0.0<x<1.0. High temperature oxide melt drop solution calorimetry was performed to determine the enthalpies of formation from binary oxides and the enthalpy of mixing. There is a noticeable change in the energetics of the solid solution near x=0.7, which is due to the growing concentration of Fe⁴⁺ at higher Fe/(Fe+Mn) ratio. The balance between different valences of the transition metals, Mn and Fe, is the main factor in determining the energetics of the La_0.70Sr_0.30Fe_xMn_1−xO₃ solid solution.     

A novel germanate, Cu2Fe2Ge4O13, with a four tetrahedra oligomer

The structure of Cu₂Fe₂Ge₄O₁₃, previously thought to be CuFeGe₂O₆, has been determined from single-crystal X-ray diffraction data to be monoclinic, P2₁/m, a=12.1050(6), b=8.5073(4), c=4.8736(2) Å, β=96.145(1)°, Z=2, with R1=0.0231 and wR2=0.0605. The unique structure has an oligomer of four germanate tetrahedra, cross-linked laterally by square-planar copper ions, joined end-to-end by a zigzag chain of edge-sharing iron oxide octahedra. Running along the a-direction the metal oxide chain consists of alternating Cu-Cu and Fe-Fe dimers. A hypothetical series of homologous structures (Cu_n−2Fe₂Ge_nO_3n+1 with n=3,4,…,∞) with different length germanate oligomers is proposed, where as n increases, the infinite chain of the CuGeO₃ is approached. In this context, Cu₂Fe₂Ge₄O₁₃ is viewed as being built from blocks of CuGeO₃ and the Fe oxide chains. This material has significance to the study of low-dimensional mixed-spin systems.     

High-pressure transitions in MgAl2O4 and a new high-pressure phase of Mg2Al2O5

Phase transitions in MgAl₂O₄ were examined at 21-27 GPa and 1400-2500 °C using a multianvil apparatus. A mixture of MgO and Al₂O₃ corundum that are high-pressure dissociation products of MgAl₂O₄ spinel combines into calcium-ferrite type MgAl₂O₄ at 26-27 GPa and 1400-2000 °C. At temperature above 2000 °C at pressure below 25.5 GPa, a mixture of Al₂O₃ corundum and a new phase with Mg₂Al₂O₅ composition is stable. The transition boundary between the two fields has a strongly negative pressure-temperature slope. Structure analysis and Rietveld refinement on the basis of the powder X-ray diffraction profile of the Mg₂Al₂O₅ phase indicated that the phase represented a new structure type with orthorhombic symmetry (Pbam), and the lattice parameters were determined as a=9.3710(6) Å, b=12.1952(6) Å, c=2.7916(2) Å, V=319.03(3) Å³, Z=4. The structure consists of edge-sharing and corner-sharing (Mg, Al)O₆ octahedra, and contains chains of edge-sharing octahedra running along the c-axis. A part of Mg atoms are accommodated in six-coordinated trigonal prism sites in tunnels surrounded by the chains of edge-sharing (Mg, Al)O₆ octahedra. The structure is related with that of ludwigite (Mg, Fe²⁺)₂(Fe³⁺, Al)(BO₃)O₂. The molar volume of the Mg₂Al₂O₅ phase is smaller by 0.18% than sum of molar volumes of 2MgO and Al₂O₃ corundum. High-pressure dissociation to the mixture of corundum-type phase and the phase with ludwigite-related structure has been found only in MgAl₂O₄ among various A²⁺B³⁺₂O₄ compounds.     

Structure and conductivity of strontium-doped cerium orthovanadates Ce1−xSrxVO4 (0≤x≤0.175)

A-site substituted cerium orthovanadates, Ce_1−xSr_xVO₄, were synthesised by solid-state reactions. It was found that the solid solution limit in Ce_1−xSr_xVO₄ is at x=0.175. The crystal structure was analysed by X-ray diffraction and it exhibits a tetragonal zircon structure of space group I4₁/amd (1 4 1) with a=7.3670 (3) and c=6.4894 (1) Å for Ce_0.825Sr_0.175VO₄. The UV-vis absorption spectra indicated that the compounds have band gaps at room temperature in the range 4.5-4.6 eV. Conductivity measurements were performed for the first time up to the strontium solid solution limit in air and in dry 5% H₂/Ar with conductivity values at 600 °C ranging from 0.3 to 30 mS cm⁻¹ in air to 30-45 mS cm⁻¹ in reduced atmosphere. Sample Ce_0.825Sr_0.175VO₄ is redox stable at a temperature below 600 °C although the conductivity is not high enough to be used as an electrode for solid oxide fuel cells.     

Defect clusters and precipitation/oxidation of MgO-Co1−xO solid solution

MgO and Co_1−xO powders in 9:1 and 1:9 molar ratio (denoted as M₉C₁ and M₁C₉, respectively) were sintered and homogenized at 1600°C followed by annealing at 850°C and 800°C, respectively to form defect clusters and precipitates. Analytical electron microscopic observations indicated the protoxide remained as rock salt structure with complicated planar diffraction contrast for M₉C₁ sample, however with spinel paracrystal precipitated from the M₁C₉ sample due to the assembly of charge- and volume-compensating defects of the 4:1 type, i.e., four octahedral vacant sites surrounding one Co³⁺-filled tetrahedral interstitial site. The spacing of such defect clusters is 4.5 times the lattice spacing of the average spinel structure of Mg-doped Co_3−δO₄, indicating a higher defect cluster concentration than undoped Co_3−δO₄. The {111} faulting of Mg-doped Co_3−δO₄/Co_1−xO in the annealed M₁C₉ sample implies the possible presence of zinc blend-type defect clusters with cation vacancies assembled along oxygen close packed (111) plane.