Extraction and separation of cationic surfactants from river sediments: application to a spectrophotometric determination of cationic surfactant in an aquatic environment using membrane filters.

The quantitative extraction of cationic surfactant (CS+) in river sediments was studied. Further, the developed method was applied to the spectrophotometric determination of CS+ in urban river sediment samples by solid-phase extraction with membranes. A mixture of methanol and hydrochloric acid was proposed as an eluent. Dried sediment was digested in the eluent under ultrasonic irradiation. After elution, the eluent was evaporated to almost dryness. The residue was dissolved in a small volume of methanol and diluted to a certain volume with water. The pH of the solution was adjusted to 4-5 to separate iron and some other metals as precipitates of hydroxides. The solution was passed through two-piled membranes: first glass-fiber and then polytetrafluoroethylene (PTFE) membranes. A small volume of methanol was passed through the membranes to elute any CS+ retaining on the membranes. After passing the methanol solution through a cationic exchange resin column, the retained CS+ was eluted with methanol containing a high concentration of sodium chloride. Water, Bromophenol Blue (BPB) and hydrochloric acid were added to the solution. The solution was passed through a mixed cellulose ester membrane filter to retain an ion associate of CS+.BPB-. The retained ion associate was dissolved in a small volume of N,N-dimethylformamide together with the membrane filter, followed by the addition of triethanolamine to make the solution alkaline. The absorbance due to BPB2- was measured at 603 nm against a reagent blank. This method was applied to the determination of CS+ in river water and sediment. A cationic surfactant in sediments at 10(-5) mol kg-1 levels was detected with satisfactory precision. It was found that CS+ was about 500-fold enriched in the sediment from water at the place where domestic wastewater was discharged.     

Purification method for recombinant proteins based on a fusion between the target protein and the C-terminus of calmodulin

Calmodulin (CaM) was used as an affinity tail to facilitate the purification of the green fluorescent protein (GFP), which was used as a model target protein. The protein GFP was fused to the C-terminus of CaM, and a factor Xa cleavage site was introduced between the two proteins. A CaM-GFP fusion protein was expressed in E. coli and purified on a phenothiazine-derivatized silica column. CaM binds to the phenothiazine on the column in a Ca(2+)-dependent fashion and it was, therefore, used as an affinity tail for the purification of GFP. The fusion protein bound to the affinity column was then subjected to a proteolytic digestion with factor Xa. Pure GFP was eluted with a Ca(2+)-containing buffer, while CaM was eluted later with a buffer containing the Ca(2+)-chelating agent EGTA. The purity of the isolated GFP was verified by SDS-PAGE, and the fluorescence properties of the purified GFP were characterized.     

A procedure for calibration transfer between near-infrared instruments--a worked example using a transmittance single tablet assay for piroxicam in intact tablets

A procedure was developed for different modes of calibration transfer in near-infrared (NIR) spectroscopy, which included a method for the selection of a subset of samples appropriate for transfer. As a worked example, these guidelines were applied to the transfer of a multivariate calibration model, representing a validated NIR single tablet assay for the active within an intact pharmaceutical product, between three equivalent dispersive NIR transmission instruments. Transfer was first evaluated between two instruments, representing the situation where both were available during calibration development. A spectral correction method alone, applied to the transfer instrument, was not sufficient to facilitate transfer, with further optimisation of the calibration model using a novel wavelength selection algorithm necessary to remove regions of the spectral range that resulted in skewed predictions on the second instrument. Through this approach, a single calibration model was found to be equally accurate and precise on the two instruments. A procedure, using the Kennard-Stone algorithm, is described for determining a reduced number of samples as a transfer set using only the spectral information from the original instrument. The purpose of the subset was to permit transfer to a new instrument where that instrument was not available until after calibration development or where it was undesirable to re-measure the full sample set (i.e. due to excessive reference chemistry). Utilising the transfer set, transfer to a third instrument was evaluated. The calibration model, optimised between the first two instruments, was not directly applicable for the third instrument, with further wavelength selection required to remove a small region of spectral data. On completion, using a full statistical evaluation, a single calibration model was found to be equally accurate and precise on all three instruments.     

Flow injection analysis of DPPH radical based on electron spin resonance

In order to construct a rapid and selective determination system of free radicals, we developed an FIA system using an electron spin resonance (ESR) spectrophotometer (flow injection spin analysis) equipped with a flow-through flat cell. In the present investigation, 1,1-diphenyl-2-picrylhydrazyl (DPPH) was used as a model free radical. Using a single line flow system, 0.5 mM DPPH was repetitively injected. When the magnetic field was fixed at 335.3 mT, the largest change in the ESR signal was observed and obtained peak height was proportional to the concentration of DPPH radical. A double line flow system was constructed in which a carrier stream containing 0.15 mM DPPH was fed into the flat cell after confluence with a sample stream. When ascorbic acid was injected as a typical DPPH radical scavenger, a negative peak appeared in proportional to the concentration. Lower detection limit of ascorbic acid was 0.01 mM (S/N=4), sampling frequency was 13 samples per h, and a satisfactory reproducibility (CV=3.2%, 0.1 mM, n=5) was obtained. The present system was also applied to estimate the DPPH radical-scavenging activity of other substances and food samples.     

Studies on Surface Properties and Cell Adhesion Properties of BSA Modified DBM Scaffold

As a scaffold material for bone tissue engineering, demineralized bone matrix(DBM) has such a limited ability to load cells and growth factors that the surface of the DBM scaffold was modified with bovine serum albumin(BSA) with different concentrations to improve the protein stmcture and physicochemical properties of the scaffold surface so as to enhance the adhesion of the cells. And the appropriate BSA concentration was explored. Compared with DBM, the scaffold with BSA coating had a smaller pore size and a lower porosity, also, the degradation rate was accelerated and the hydrophilic property was improved. Cells adhesion was observed inside the DBM seaffold before and after it had been modified, and the BSA modified scaffold had a good cell compatibility. Wlien the concentration of BSA was 20 mg/mL, the adhesion ability of the cells to modified scaffold was significantly increased, and the cell proliferation was facilitated.     

Biological component microanalysis by laser photoacoustic imaging immunoassay

Computerized laser photoacoustic microscopy was developed and applied to the immuno-selective imaging of the microdistribution of a biological component. Human lambda-type light-chain was chosen as a model target protein and its peroxidase conjugated antibody was used for selective binding to the target protein and its staining. Using a microscopic calibration curve which was obtained from the images of homogeneously dispersed standard samples, the total quantities of randomly dispersed artificial standard samples were estimated to evaluate the reliability of this method. Finally, the method was applied to a tissue section sample, a human fetal pancreas section, to get the local and total quantitative images of the lambda-type light-chain.     

Spectroelectrochemistry study on the electrochemical reduction of ethidium bromide.

The electrochemical reduction mechanism of ethidium bromide was first studied by spectroelectrochemistry. This reduction was proved to be a two-step process by cyclic voltammetry, differential pulse voltammetry and spectroelectrochemistry, in which each step was proved to be a one-electron transfer process by a spectropotentiostatic fluorescence technique. Hydroethidine was confirmed to be the final product by comparing the spectrum of the product of the electrochemical reduction to that of the product of the chemical reduction of ethidium bromide, and a carbon-centered radical was concluded to be a reasonable intermediate product during the electrochemical reduction of ethidium bromide.     

Xylan enriched viscose fibers

In this study, a new xylan enriched viscose fiber was developed. A high molecular weight xylan with a degree of polymerization of 150–200 was added during a late stage of the viscose production process. The xylan deriving from a cold caustic extraction (CCE) of an eucalypt paper pulp was introduced to the process after xanthation and thus neither objected to any degradation conditions during alkalization nor to the xanthation step. About 90 % of the added xylan was transferred to the final fiber. A xylan content of up to 7.5 % was achieved. Fiber properties like strength showed a comparable level to the reference fibers while the water retention value was clearly raised due to the higher content of hemicelluloses. The hemicellulose distribution over the fiber cross section was investigated by enzymatic peeling. Even though a segregation of the different polysaccharides was observed, the goal of a good blending of CCE-xylan into cellulosic fibers with new interesting features was achieved.     

Problems on the Evaluation of the Critical Wavelength of Sunscreens for “Broad Spectrum” Approval Brought on by Viscous Fingering During Sunscreen Application

When a viscous liquid is applied to a solid substrate, a patterned liquid layer is usually formed by the phenomenon called viscous fingering, since the moving liquid surface is in far‐from‐equilibrium conditions to let the morphological fluctuation to grow. Pseudosunscreen solutions were prepared and applied on a flat quartz plate. A spatially periodic stripe pattern was formed on the pseudosunscreen layer when a block applicator was used, whereas a flat surface layer was formed when a four‐sided applicator was used. UV absorbance of the patterned layer was lower than that of the flat layer having the same average thickness. In addition, a larger decrease in the UV absorbance by the pattern formation was observed at wavelengths at which the UV absorbance of the flat layer was large, which was consistent with theoretical simulations. In 2011, US FDA introduced a new rule using the term “Broad Spectrum” for labeling the sunscreens. The different decrease in the UV absorbance at each wavelength was found to change the critical wavelength, which is a criterion for sunscreens to be labeled as “Broad Spectrum” protection. The result of this study makes the problem on the evaluation of the critical wavelength come to the surface.     

Reflective thermal lens detection device

A reflective thermal lens detection device was developed for realizing a portable and sensitive detector for a microsystem. An aluminum mirror was formed on the main plate of a microchip, and a reflected probe beam was detected with a single pick-up unit. The background signal due to light absorption of the aluminum mirror was 60 times reduced when the microchannel and the mirror were separated with an interval of 600 microm. The tilt angle of the microchip significantly affected the precision of the measurement. Then a quadrant photodiode was used to detect the center of gravity of the reflected probe beam to regulate the tilt angle within +/-0.05 degrees , and this value was enough to achieve 1% CV (coefficient of variance) precision in the measurements. The limit of detection (LOD) was 60 nM for xylene cyanol solution, and the absorbance was 9.4 x 10(-6) AU. About 40 times higher sensitivity was obtained in comparison with a spectrophotometer.     

Chip-based capillary electrophoresis with an electrodeless nanospray interface

A sheathless and electrodeless nanospray interface has been used to interface a polycarbonate capillary electrophoresis (CE) chip to a mass spectrometer (MS). The chip was made of two flat polycarbonate plates which were bolted together. Channels were imprinted in one of the plates with metal wires, using a hydraulic press. A short tapered capillary connected to the chip was used as the nanospray emitter. The advantage of this electrodeless interface is that it was not necessary to apply a electrospray voltage to the chip or the nanospray emitter. Instead, the CE voltage already applied to the buffer compartment on the chip, to drive the electrophoresis, was used to generate the spray also. A low conductivity buffer of 1.25 mmol/L ammonium acetate in 80% methanol was used to obtain a large electric field across the buffer channel. The performance of the device was evaluated by analyzing a mixture of three beta-agonists Relative standard deviation (RSD) values obtained were between 4.8 and 5.0%. A sample concentration of 40 nmol/L resulted in a signal-to-noise ratio of 2 to 5 for the different components. Compared to a conventional CE analysis in a fused silica capillary with UV detection, only a minor loss of resolution was observed, which can be attributed to the design of the chip.     

Permeation of complexed metal ions through a hydrophobic membrane

Selective concentration of a heavy metal complex with acetylacetone (acac) through a hydrophobic polystyrene membrane was carried out under a pressure gradient. A chelate forming heavy metal was selectively concentrated about 2 fold by this method. When using a coating membrane with a high water flux, the permeabilities increased with increasing complex fraction in the aqueous solution, while using a membrane with a low water flux, a bulky complex was not highly concentrated because of steric hindrance. The complex partitioned on the membrane surface was transported and concentrated under a pressure gradient and a linear relationship was found to exist between permeabilities and partition coefficients. It will be possible to concentrate hydrophobic organic solutes by this method, for acac was concentrated when the Cu—acac complex was formed. As the permeabilities increased with decreasing pressure and membrane compaction was strong for a coating membrane, it seems effective to permeate at a low pressure.     

采用流变学方法研究聚酰胺酸6FDA-TFDB溶液的降解行为

合成了一种聚酰胺酸6FDA-TFDB溶液,利用流变仪研究其在不同影响因素(如:温度、升温速率、溶剂含水量等)下的流变行为,发现聚酰胺酸溶液的降解在高温区和低温区存在不同的行为.通过Andrade公式获得不同条件下聚酰胺酸溶液的黏流活化能,并比较其差异,同时对溶剂水含量在不同温度区域下对聚酰胺酸降解速率的影响也进行了深入的分析,从而建立一种半定量比较不同条件下聚酰胺酸溶液降解速率的方法.     

Immobilization of ultra-thin layer of monoclonal antibody on glass surface

When preparing an affinity column and a biosensor, it is desirable to immobilize a unimolecular layer of pure protein on a matrix. In this work, we tried to immobilize a monoclonal antibody on a surface of a glass test-tube as a model, to confirm the stability of this ultra-thin layer by an enzyme immunoassay, and to estimate the thickness of the layer on a slide glass by Fourier transform infrared reflection spectrometry. A new test-tube was washed and dried. The tube was filled with 5% 3-aminopropyltriethoxysilane. The 3-aminopropylsilylated surface was treated with glutaraldehyde and 5.6.10(-2) mg/ml solution of a normal mouse monoclonal antibody. The Schiff base between glutaraldehyde and the antibody was further reduced with 7.9.10(-3)% NaBH4. The tube was washed with 0.05% Tween 20 to block non-specific binding. The antibody immobilized on the surface was measured by an enzyme immunoassay based on a reaction of anti-mouse immunoglobulin G labelled with alkaline phosphatase, with which p-nitrophenol was produced from p-nitrophenylphosphate as a substrate. Meanwhile, various amounts of the antibody were immobilized on slide glasses in the same manner. The antibody on each surface was measured by Fourier transform infrared reflection spectrometry. The antibody immobilized under the final conditions was detectable by the enzyme immunoassay, and stable at 4 degrees C for ten days. The antibody on the slide glass was a unimolecular layer, as judged from the Fourier transform infrared spectra referred to -CONH- band semiquantitatively. Thus, we found the optimal conditions for immobilizing an ultra-thin layer of the monoclonal antibody on the glass surface.(ABSTRACT TRUNCATED AT 250 WORDS)     

Molecularly imprinted polymers for the clean-up of a basic drug from environmental and biological samples

A molecularly imprinted polymer (MIP) was synthesized and evaluated to selectively extract an alpha-blocker, i.e. alfuzosin, from human plasma. The synthesis of the MIP was performed in dichloromethane with methacrylic acid as monomer and the target drug as template. A first series of experiments was carried out in dichloromethane to estimate the potential of the MIP in its specific recognition medium, i.e. dichloromethane, by developing a selective procedure and by measuring the capacity of the sorbent. An optimized procedure was developed for the selective extraction of alfuzosin with a recovery close to 100% in this medium and a specific capacity of 1.3 micromol g(-1) of MIP was measured. A study in aqueous media was also carried out by a comprehensive approach of the retention mechanism in order to build a selective procedure of extraction. The effects of the amount and of the charge of cations were studied and an optimal pH value was defined to limit matrix effects. Then, the alfuzosin MIP was then directly used to selectively extract the target drug from human plasma with an extraction recovery of 60%. Lastly, a soil was extracted by a pressurized solvent and the resulting extract was cleaned up on the MIP, showing the possibility to use this selective sorbent for the sample treatment of various complex matrices.     

Exploratory Analysis of Micrographic Teflon Images

 Some analytical techniques are able to produce images, making if possible to obtain a large amount of information. Working with images, the pixels can be treated like objects in a data matrix. In this way, a multi-way PCA of micrograph images was applied to the internal surface of a Teflon coil used for microwave sample digestion. This Teflon coil was used for 120 h and had been attacked with different acids. It was cut into 3 pieces (namely: initial, medium and central portions) in order to obtain 7 micrographs (2 for initial, 2 for medium and 3 for the central part). A micrograph of a piece from a new Teflon coil was used for comparison. With these 8 micrographs, it was possible to establish a three-dimensional arrangement. After multi-way PCA was applied to the Teflon surface images, was possible to group a great amount of information and to characterise different parts of this coil. Received March 3, 2000. Revision July 28, 2000.     

Lamp‐based wavelength‐resolved fluorescence detection for protein capillary electrophoresis: Setup and detector performance

A lamp‐based fluorescence detection (Flu) system for CE was extended with a wavelength‐resolved (WR) detector to allow recording of full protein emission spectra. WRFlu was achieved using a fluorescence cell that employs optical fibres to lead excitation light from a Xe‐Hg lamp to the capillary window and protein fluorescence emission to a spectrograph equipped with a CCD. A 280 nm band pass filter etc. together with a 300 nm short pass cut‐off filter was used for excitation. A capillary cartridge was modified to hold the detection cell in a commercial CE instrument enabling WRFlu in routine CE. The performance of the WRFlu detection was evaluated and optimised using lysozyme as model protein. Based on reference spectral data, a signal‐intensity adjustment was introduced to correct for transmission losses in the detector optics that occurred for lower protein emission wavelengths. CE‐WRFlu of lysozyme was performed using BGEs of 50 mM sodium phosphate (pH 6.5 or 3.0) and a charged‐polymer coated capillary. Using the 3‐D data set, signal averaging over time and emission‐wavelength intervals was carried out to improve the S/N of emission spectra and electropherograms. The detection limit for lysozyme was 21 nM, providing sufficient sensitivity to obtain spectral information on protein impurities.     

Circulation microchannel for liquid–liquid microextraction

A new method has been developed for liquid–liquid microextraction utilizing a circulation microchannel. A glass microchemical chip having a circular shallow microchannel in contact with a surrounding deeper microchannel was fabricated by a two-step photolithographic wet-etching technique. Surface modification reagent was selectively introduced to the shallow channel by utilizing capillary force, and the surface of the shallow channel was selectively made hydrophobic. With the aid of the hydrophobic/hydrophilic surface patterning, it was possible to keep organic solvent in the circular channel while the aqueous sample solution was continuously flowing in the deep channel. As a result, concentration extraction from sample solution to stationary extractant with a nanoliter scale volume became possible. Concentration extraction has been difficult in a multiphase continuous flow. Function of the newly developed microextraction system was verified with methyl red as a test sample, and concentration extraction to reach equilibrium was successfully carried out. A novel surface modification method utilizing frozen liquid as a masking material was also developed as a reverse process to make the shallow channel hydrophilic and the deep channel hydrophobic. Visualization of circulation motion inside the circular shallow channel induced by flow in the deep channel was observed with a particle tracing method.     

High-throughput photometric titrimetry based on a feedback-based and subsequent fixed triangular wave-controlled flow ratiometry.

The principle of flow ratiometry for high-throughput titration, which we recently proposed for potentiometric titration, was extended to photometric titration. The flow rate (FB) of a base solution containing an acid-base indicator was linearly varied in response to a control voltage (Vc) generated from a computer. With the total (acid + base) flow rate (FT) being kept constant, the base solution was merged with an acid solution, which was aspirated to the confluence point at a flow rate of FT - FB. Downstream, the relative transmittance of the mixed solution was measured at the maximum absorption wavelength of the base form of the indicator. Initially, a feedback-based control was applied, where the scan direction of Vc was reversed from upward to downward, and vice versa, whenever the transition of the indicator at the equivalence point (EP) was sensed. Next, the scan range of V. was further limited to the range just around EP by using fixed triangular waves. These processes avoided scanning in a range of no interest. Thus, an unprecedentedly high throughput rate (maximally 34 titrations per minute, corresponding to 1.76 s per titration) was realized with reasonable precision (RSD < 0.5%).     

A reductive cyclization approach to attenol A

A reductive cyclization strategy was applied to the synthesis of attenol A. This nontraditional approach to the spiroacetal structure illustrated several advantages of the reductive cyclization methodology. The attenol A core was formed in a carbon-carbon bond coupling that gave rise to a previously inaccessible spiroacetal epimer, a new method to synthesize thioketene acetals from a phenyl sulfone was realized, and the configurational stability of a nonanomeric spiroacetal was evaluated. A minor byproduct in the reductive cyclization reaction was identified that for the first time allowed direct evaluation of the stereoselectivity in a reductive cyclization of a dialkyloxy alkyllithium reagent.