High efficiency direct methanol fuel cell based on poly(styrenesulfonic) acid (PSSA)-poly(vinylidene fluoride) (PVDF) composite membranes

semi-Interpenetrating polymer network (sIPN) composite membranes consisting of poly(styrenesuflonic) acid (PSSA) and poly(vinylidene fluoride) (PVDF) have been prepared and evaluated as proton exchange membrane electrolytes in direct methanol fuel cells (DMFCs). The membranes fabricated were evaluated in terms of their proton conductivity, methanol permeability, and their performance characteristics in direct methanol fuel cells (DMFCs). PSSA-PVDF membranes demonstrated decreased methanol crossover during operation of direct methanol fuel cells compared to state-of-art Nafion^®-H membranes, yielding improved efficiency. PSSA-PVDF membranes have been demonstrated to operate efficiently in 1 in. × 1 in. and 2 in. × 2 in. direct methanol fuel cells. Fuel cells operating with PSSA-PVDF membranes were observed to have dramatically lower crossover rates compared to Nafion^® 117 systems. Greater than 95% reduction in crossover was observed in some cases. These properties of PSSA-PVDF membranes resulted in improved fuel performance and fuel cell efficiencies for direct methanol fuel cells. It was also observed that the PSSA-PVDF membranes behave quite differently compared with Nafion^®-based systems in terms water management characteristics at the cathode. The best performance with the new membranes was observed with very low oxygen or air flow rates at the cathode which is in contrast to Nafion^®-based systems, which generally require higher flow rates due to excessive water accumulation at the cathode, resulting in flooding.     

Polymer electrolyte membranes for the direct methanol fuel cell: A review

The direct methanol fuel cell (DMFC) has the potential to replace lithium‐ion rechargeable batteries in portable electronic devices, but currently experiences significant power density and efficiency losses due to high methanol crossover through polymer electrolyte membranes (PEMs). Numerous publications document the synthesis and characterization of new PEMs for the DMFC. This article reviews this research, transport phenomena in PEMs, and experimental techniques used to evaluate new PEMs for the DMFC. Although many PEMs do not show significant improvements over Nafion®, the benchmark PEM in DMFCs, experimental results show that several new PEMs exhibit lower methanol crossover at similar proton conductivities and/or higher DMFC power densities. These results and recommendations for future research are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Parts B: Polym Phys 44: 2201–2225, 2006     

Natural and synthetic solid polymer hybrid dual network membranes as electrolytes for direct methanol fuel cells

Hybrid dual-network membranes comprising chitosan (CS)–polyvinyl alcohol (PVA) networks crosslinked with sulfosuccinic acid (SSA) and glutaraldehyde (GA) and modified with stabilized silicotungstic acid (SWA) are reported for their application in direct methanol fuel cells (DMFCs). Physico-chemical properties of these membranes are evaluated using thermo-gravimetric analysis and scanning electron microscopy in conjunction with their mechanical properties. Based on water sorption and proton conductivity measurements for the membranes, the optimum content of 10 wt.% SWA in the membrane is established. The methanol crossover for these membranes are studied by measuring the mass balance of methanol using density meter and are found to be lower compared to Nafion-117 membrane. The membrane–electrode assembly with 10 wt.% stabilized SWA–CS–PVA hybrid membrane with SSA and GA as crosslinking agent delivers a peak power density of 156 mW cm⁻² at a load current density of 400 mA cm⁻² and 88 mW cm⁻² at a load current density of 300 mA cm⁻², respectively, in DMFC at 70 °C.     

Inorganic-organic Composite Membranes with Novel Microstructure for High Temperature Proton Exchange Membrane Fuel Cells

Nowadays,more and more fossil fuels are consumed and air pollurion has become a threat to the survival of people.Therefore,we need some other power sources to provide energy without damaging the environment.Proton exchange membrane fuel cells(PEMFCs)have received wide attention due to their advantages Such as high energy density and zero emission[1].Particularly, direct methanol fuel cells (DMFCs)were considered as the most suitable energy sources for electric vehicles(EVs)and portable electronics.     

Platinum–polytyramine composite material with improved performances for methanol oxidation

Polytyramine (PTy) is shown to be a possible alternative to other conducting polymers as a support material for fuel cell electrocatalysts such as platinum. In this work, a Pt–PTy composite was prepared via potentiodynamic deposition of polytyramine on graphite substrate, followed by the electrochemical deposition of Pt nanoparticles. The material obtained by this straightforward method exhibited, for platinum loadings as low as ca. 0.12 mg cm⁻², a specific electrochemically active surface area of the electrocatalyst of ca. 54 m² g⁻¹, together with a good electrocatalytic activity for methanol oxidation in acidic media, thus ensuring better efficiency of Pt utilization. The system Pt–PTy appears to be worthy of development for methanol fuel cell applications also because the results suggested that, when deposited as small particles in a PTy matrix, platinum is less sensitive to fouling during CH₃OH oxidation.     

Lattice imaging in melt crystallized polypropylene thin films

 Melt crystallized isotactic polypropylene thin films of thickness between 30 and 100 nm have been investigated by high-resolution transmission electron microscopy at room temperature. The c-axis projection of the 2^*3₁ helices and their packing in the lattice were clearly visible in flat-on lamellae of the α-phase following reconstruction from the components of the image Fourier transform corresponding to the (1 1 0) and (0 4 0) lattice planes, and the image power spectra also indicated contributions from (1 3 0) and (0 6 0) relfections, corresponding to a line resolution of about 0.35 nm. These results are discussed in terms of Bloch wave calculations based on the generally accepted structure for the α-phase. Attempts to obtain lattice images of the β-phase in isotactic polypropylene and melt crystallized syndiotactic polypropylene under similar operating conditions are also briefly discussed, although these provided relatively little structural information. Received: 27 June 1997 Accepted: 15 August 1997     

Preliminary evaluation of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid composite membranes for direct methanol fuel cell applications

A series of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid (SPEEK/MEA/AA) composite membranes are prepared and investigated to assess their possibility as proton exchange membranes in direct methanol fuel cells (DMFCs). A preliminary evaluation shows that introducing MEA and AA into SPEEK matrix decreases the thermal stability of membrane. However, the degradation temperatures are still above 260 °C, satisfying the requirement for fuel cell operation. Compared with the pure SPEEK membrane, the composite membranes exhibit not only lower water uptake and swelling ratios but also better mechanical property and oxidative stability. Noticeably, the methanol diffusion coefficient of the composite membranes decrease significantly from 3.15 × 10^?6 to 0.76 × 10^?6 cm²/s with increasing MEA and AA content, accompanied by only a small sacrifice in proton conductivity. Although both the methanol diffusion coefficient and the proton conductivity of composite membranes are lower than those of pure SPEEK and Nafion® 117 membranes, their selectivity (conductivity/methanol diffusion coefficient) are higher. In addition, the composite membranes show excellent stability in aqueous methanol solution. The good thermal and chemical stability, low swelling ratio, excellent mechanical property, low methanol diffusion coefficient, and high selectivity make the use of these composite membranes in DMFCs quite attractive. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2871–2879, 2007     

In situ UV-Vis and ex situ IR spectroelectrochemical investigations of amorphous and crystalline electrochromic Nb2O5 films in charged/discharged states

Niobium oxide (Nb₂O₅) films and powders have been obtained via the sol-gel route from an NbCl₅ precursor. XRD spectra revealed that films with pseudohexagonal (TT-phase) and orthorhombic (T-phase) structure were formed at 500  °C and 800  °C, respectively, while at 300  °C films were amorphous. Infrared (IR) and Raman spectra of powders and films of Nb₂O₅ in different polymorphic forms were detected, and vibrational band assignments were made. Electrochromic properties of amorphous films and films with the TT-phase were established from in situ ultraviolet visible (UV-Vis) spectroelectrochemical measurements and correlated with ex situ IR transmission spectra of charged films. Ex situ IR spectra revealed that charging of amorphous films is accompanied by variations of the Nb-O stretching mode intensity, while, for films with the TT- and T-phase, splitting of the Nb₃-O stretching modes and the appearance of polaron absorption were noted with Li⁺ ion insertion. Ex situ X-ray diffraction (XRD) spectra of charged films with the TT-phase showed changes of the unit cell dimensions with charging. The influence of the polaron absorption on the ex situ near-grazing incidence angle (NGIA) IR reflection-absorption spectra of charged/discharged films is discussed in detail. Received: 21 August 1997 / Accepted: 9 October 1997     

直接甲醇燃料电池纳米结构电催化材料及多孔电极研究

直接甲醇燃料电池(DMFC)因其燃料能量密度高,工作温度低,低污染排放等优点被认为是用作移动设备电源的最佳选择之一,至今已有美国的Oorja Protonics公司和丹麦的IRD公司等新能源相关企业相继发布了多款用于手机、电脑、通信基站、叉式装卸机或房车的商业产品.然而, DMFC内部的复杂情况造成的多种不同的电压损失仍旧使得其实际电压效率远低于理论值.其中从阳极渗透到阴极的甲醇造成的混合电位导致的电压损失尤为明显.目前,众多研究人员都致力于开发高稳定性、高耐久性、高性能且低成本的催化材料体系,以克服传统Pt催化剂存在的各种问题.除了催化剂本身之外, DMFC的问题还与其中膜电极的微结构和电化学特性息息相关.膜电极是化学能通过电催化氧化还原反应转化为电能的反应场所,通常由阳极扩散层、阳极催化层、质子交换膜、阴极催化层和阴极扩散层依序组合而成.通过对MEA中的各层进行优化,如传质管理和甲醇渗透等问题都能得到有效解决.
　　近年来,纳米技术常被用于改进DMFC性能的研究.具备纳米结构的金属-碳/金属氧化物载体类催化材料得到了广泛研究.这些电催化材料在制备方法、结构和组分上都有较大区别.结构方面,许多研究都证明制备纳米级多孔网络结构或者有序阵列结构的催化层有助于提高催化性能和Pt的利用率.组分方面,许多研究人员都开展了引入Pt以外金属成分或金属氧化物来改变Pt催化剂的表面电子状态的研究.引入这些组分导致的配位体效应可以通过弱化Pt与H+, OH-或COads等的相互作用来起到抗催化毒化和提高催化效率的作用.尽管对于DMFC领域的认知逐渐完善,但是仍有许多问题有待解决.因此,本文介绍了目前用于DMFC的纳米结构电催化材料和多孔电极的研究进展.重点介绍了纳米结构催化剂和载体材料的合成及表征.
　　通过对比不同催化材料的特性可以发现,在本文涉及到的催化材料中, In0.1SnO2-Pt和(MoO3)0.2SnO2-Pt/C表现出了最高的催化活性,但是它们高效催化甲醇电氧化所需的碱性环境与现在占绝对主流地位的Nafion质子交换膜所必须的酸性环境相冲突,所以其实际应用价值在碱性阴离子交换膜研究取得突破前都难以有效发挥.而另一类表现较好的采用溶致液晶模板法合成的纳米树枝状和纳米星形Pt催化剂则存在制备工艺难以商业规模化的问题.总的来说,采用溶剂热合成法制备的Pt-NRCeO2/GNs和Pt/Ti0.9Sn0.1O2-C等纳米结构金属氧化物、碳材料复合载体和Pt基贵金属催化剂组成的催化材料体系不仅催化性能相对于商业化Pt纳米颗粒有很大提高,而且制备方法易于商业规模化,值得进一步关注.此外,本文还介绍了如内部传质过程的理论建模计算和膜电极中功能结构的制备等优化DMFC中多孔电极内传质过程的方法.通过计算机模拟得到优化DMFC内部传质过程所需的扩散层、催化层的传质特性相关参数,再通过改进MEA制备工艺,有效控制各层的结构参数向模拟的优化值靠拢,能够实现DMFC性能的有效提升.综合模拟、实验研究及工艺研究结果,根据实际需要,设计和制备包含新功能层的MEA的相关研究也更进一步提高了DMFC的性能和实用性.就目前的研究情况而言,如果在性能提升的基础上,使用寿命再取得突破, DMFC一定会有很好的商业应用前景.     

Enhanced recovery of chlorophenols from surface waters using polymer based extraction cartridges

 The effectiveness of a new polymer based solid phase extraction cartridge (SDB 1) to recover phenolic compounds from aqueous samples has been evaluated by comparison of performance against conventional silica based cartridges. The polymer based material is found to be much more retentive, requiring a larger volume of solvent to achieve maximum recovery. Recovery efficiency is enhanced if the recovery solvent (methanol) is acidified to 0.1% with trifluoroacetic acid. The optimised extraction procedure has been applied to surface water samples and yields quantitative recovery at the 10 ng ml^-1 level of all nine phenols studied. Received: 26 November 1996/Revised: 21 March 1997/Accepted: 30 March 1997     

On-line mass spectrometry of the electro-oxidation of methanol in acidic media on tungsten carbide

The electro-oxidation of methanol at supported tungsten carbide (WC) nanoparticles in sulfuric acid solution was studied using cyclic voltammetry, potentiostatic measurements, and differential electrochemical mass spectroscopy (DEMS). The catalyst was prepared by a sonochemical method and characterized by X-ray diffraction. Over the WC catalyst, the oxidation of methanol (1 M in a sulfuric acid electrolyte) begins at a potential below 0.5 V/RHE during the anodic sweep. During potentiostatic measurements, a maximum current of 0.8 mA mg⁻¹ was obtained at 0.4 V. Measurements of DEMS showed that the methanol oxidation reaction over tungsten carbide produces CO₂ (m/z = 44); no methylformate (m/z = 60) was detected. These results are discussed in the context of the continued search for alternative materials for the anode catalyst of direct methanol fuel cells. In memoriam     

Solution combustion synthesis of YCoO3 and investigation of its catalytic properties by cyclic voltammetery

In this paper, the synthesis of YCoO₃ by solution combustion method and investigation of its catalytic activity using cyclic voltammetry is presented. The perovskite phase was obtained by thermal initializing of the solutions of the metal nitrates and the fuel (urea). The obtained solid precursor was further heated yielding the perovskite phase. The obtained perovskite compound has orthorhombic unit cell, within the space group Pnma, with unit cell parameters a = 5.4223 ?, b = 7.3657 ?, and c = 5.1385 ?. The catalytic activity of the prepared perovskite was investigated by cyclic voltammetry using YCoO₃-modified paraffin impregnated graphite electrode, in several electrolytes. It was found that the YCoO₃ perovskite has a distinct catalytic activity towards the oxidation of chloride anions in which Co³⁺ ions being the active centers. Also, this material enhances the oxidation of methanol in KOH.     

Contribution of nanoclays to the barrier properties of a model proton exchange membrane for fuel cell application

Direct methanol fuel cells (DMFCs) that use a proton exchange membrane (PEM) as electrolyte, is a promising alternative source of energy for the future. However, methanol crossover from the anodic side to the cathodic one is a major problem in DMFC. Proper dispersion of layered silicates within the fuel cell membrane has been proposed as a strategy for improving the barrier properties of the membrane. The validity of this approach has been tested in case of a model membrane consisting of phosphotungstic acid doped poly(vinyl alcohol). A solvent casting technique has been used, which allows the nanofiller to be delaminated by an ultrasonic pre-treatment, as confirmed by TEM and XRD analysis. The layered silicates have a favourable impact on the methanol permeability, whose the decrease overcompensates some loss in ionic conductivity.     

Physical and morphological characteristics and electrochemical behaviour in PEM fuel cells of PtRu /C catalysts

Platinum-ruthenium catalysts supported on carbon (PtRu/C) have been characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), specific surface area analysis (BET), X-ray photoelectron spectroscopy (XPS) and in proton exchange membrane (PEM) fuel cell tests. The results indicate the presence of strong metal-carbon interactions, which hinder the formation of a single-phase face-centered cubic (fcc) PtRu alloy. The particle size of the PtRu/C catalysts was smaller than both carbon-supported platinum (Pt/C) and ruthenium (Ru/C) catalysts. In the bimetallic electrocatalysts the intercrystallite distance decreased with respect to pure Pt and Ru metals. PEM fuel cell tests in H₂/air operation mode revealed a decrease of performance with increasing carbon content of the catalyst, at a fixed Pt loading. In H₂ + 100 ppm CO/air operation mode the maximum performance of the PEM fuel cell was attained at 0.63 atomic fraction Ru. Received: 2 December 1999 / Accepted: 27 January 2000     

Time-resolved near-infrared and two-dimensional near-infrared correlation spectroscopic studies on polymerization of the silane coupling agent perfluorooctyltrimethoxysilane

 The polymerization behavior of perfluorooctyltrimethoxysilane (PFOS) in ethanol, which is acid-catalyzed by 0.25 M HCl, has been examined using time-resolved near-IR and 2D near-IR correlation spectra. In the time-resolved near-IR spectra, the bands at 5164 and 4825 cm⁻¹ have been assigned to the combination bands of water and ethanol OH groups, respectively. It has been found that the absorbance variation of the two near-IR bands occurs in a two-step process. The absorbance of the 5164 cm⁻¹ band rapidly decreases in the initial step but increases exponentially in the second step, while that of the 4825 cm⁻¹ band rapidly increases both in the initial step and, exponentially, in the second step. These results indicate that the time-dependent absorbance variation of the two near-IR bands reflects the polymerization process of PFOS, in which consumption and release of water molecules and release of methanol in the two-step process occur as a consequence of the acid-catalyzed hydrolysis of methoxy groups and the formation of silanols (SiOH) to form a siloxane bond. It has also been found that this polymerization process is distinctly reflected in the 2D near-IR correlation spectra. Received: 23 November 1999/Received in Revised form: 23 February 2000/Accepted 4 March 2000     

Novel sulphonated poly (vinyl chloride)/poly (2-acrylamido-2-methylpropane sulphonic acid) blends-based polyelectrolyte membranes for direct methanol fuel cells

Proton-conducting and methanol barrier properties of the proton exchange membrane (PEM), as well as the high cost of direct methanol fuel cell (DMFC) components, are the key determinants of the performance and commercialization of DMFCs. Therefore, this study aimed to develop cost- and performance-effective membranes based on sulphonated poly (vinyl chloride) (SPVC)/poly (2-acrylamido-2-methyl-1-propane sulphonic acid) (PAMPS) blends. Such membranes have been simply prepared by blending SPVC and PAMPS solutions, followed by solvent evaporation via casting. Interaction of SPVC with PAMPS was confirmed by different characterization techniques such as Fourier Transform Infra-red (FTIR) and Raman scattering spectroscopy in which the two characteristic absorption bands of sulfonic groups appeared at 1093 and 1219 cm⁻¹ additionally, strong peaks at around 1656 cm⁻¹ attributed to vibration of amide groups of PAMPS portion in the polymer blend. Furthermore, the interaction of SPVC with PAMPS improves the thermal properties along with ion exchange capacity in turn decreasing the methanol permeability through the membrane in comparison with the SPVC membrane. The IEC of PVC and Nafion 117 membranes were 1.25, 0.91 meq/g; respectively. And the maximum water uptake of PVC and Nafion 117 membranes were 75 and 65.44%; respectively. Methanol permeability value of 7.7 × 10⁻⁷ cm²/s which was noticeably lower than the corresponding value recorded for Nafion® (3.39 × 10⁻⁶ cm²/s). Therefore, these fabricated membranes can be considered a low-cost efficient candidate for use in DMFC, especially for its capability to resolve the methanol cross-over issue.     

Recent development of methanol electrooxidation catalysts for direct methanol fuel cell

Direct methanol fuel cells(DMFCs) are very promising power source for stationary and portable miniature electric appliances due to its high efficiency and low emissions of pollutants. As the key material, catalysts for both cathode and anode face several problems which hinder the commercialization of DMFCs.In this review, we mainly focus on anode catalysts of DMFCs. The process and mechanism of methanol electrooxidation on Pt and Pt-based catalysts in acidic medium have been introduced. The influences of size effect and morphology on electrocatalytic activity are discussed though whether there is a size effect in MOR catalyst is under debate. Besides, the non Pt catalysts are also listed to emphasize though Pt is still deemed as the indispensable element in anode catalyst of DMFCs in acidic medium. Different catalyst systems are compared to illustrate the level of research at present. Some debates need to be verified with experimental evidences.     

Electrodeposition of Platinum Nanoparticles on Multi-Walled Carbon Nanotubes for Electrocatalytic Oxidation of Methanol

Platinum (Pt) nanoparticles were deposited at the surface of well-aligned multi-walled carbon nanotubes (MWNTs) by potential cycling between +0.50 and −0.70 V at a scanning rate of 50 mV · s⁻¹ in 5 mM Na₂PtCl₆ solution containing 0.1 M NaCl. The electrocatalytic oxidation of methanol at the nanocomposites of Pt nanoparticles/nanotubes (Pt_nano/MWNTs) has been investigated using 0.2 M H₂SO₄ as supporting electrolyte. The effects of various parameters, such as Pt loading, concentration of methanol, medium temperature as well as the stability of Pt_nano/MWNTs electrode, have been studied. Compared to glassy carbon electrode, carbon nanotube electrode significantly enhances the catalytic efficiency of Pt nanoparticles for methanol oxidation. This improvement in performance is due not only to the high surface area and the fast electron transfer rate of nanotubes but also to the highly dispersed Pt nanoparticles as electrocatalysts at the tips and the sidewalls of nanotubes.     

Rapid determination of alcohols in human saliva by gas chromatography differential mobility spectrometry following selective membrane extraction

A fast quantitative assay for the selective and sensitive measurement of methanol and ethanol in human saliva has been developed. A hyphenated thermal desorption (TD) – gas chromatography (GC) – differential mobility spectrometry (DMS) technique was developed to characterise methanol in human saliva at concentrations between 25 mg dm⁻³ and 1000 mg dm⁻³, in the presence of elevated ethanol concentrations. A temperature-controlled polydimethylsilicone capillary membrane was used in the sampling procedure to extract methanol in the presence of elevated ethanol concentrations. A flow of nitrogen through the central channel of the membrane swept the volatile analytes into an adsorbent trap. TD-GC-DMS was used to isolate, detect and identify each compound with an analysis time of less than 3 min. The method was optimised using a 2 factor (temperature and dispersion field strength), 2 centroid point, central composite design, to enhance the resolution and sensitivity of DMS responses to methanol and ethanol. The optimum DMS cell temperature was found to be 80 °C with an optimum dispersion field strength of 24 kV cm⁻¹. A linear response was obtained for methanol over the range 25 to 500 mg dm⁻³ (R² = 0.998) The development of this method to provide point-of-care testing for ethanol and methanol exposure is discussed.     

Activation of methanol-tolerant carbon-supported RuSe<Subscript>x</Subscript> electrocatalytic nanoparticles towards more efficient oxygen reduction

An electrocatalytic system that utilizes tungsten oxide modified carbon-supported RuSe_x nanoparticles is developed and characterized here using transmission electron microscopy and such electrochemical diagnostic techniques as cyclic voltammetry and rotating ring-disk voltammetry, as well as upon its introduction (as cathode) to the low-temperature hydrogen–oxygen fuel cell. After the modification of RuSe_x catalytic centers with ultra-thin films of WO₃, the potential of oxygen reduction in 0.5 mol dm⁻³ H₂SO₄ (in the absence and presence of methanol) is shifted ca. 70 mV (under rotating disk voltammetric conditions) towards more positive values, and the percent formation (at ring) of the undesirable hydrogen peroxide has decreased approximately twice when compared to the WO₃-free system. Relative to bare electrocatalyst, an increase of power density from 75 to 100 mW cm⁻² (at 300 mA cm⁻²) has been observed upon utilization of WO₃-modified RuSe_x in polymer electrolyte membrane fuel cell at 80 °C. In comparison to Vulcan-supported Pt nanoparticles, the overall electrocatalytic performance of tungsten oxide modified carbon-supported RuSe_x nanoparticles is lower, but the latter system is practically insensitive to the presence of methanol even at 0.5 mol dm⁻³ level. Dedicated to Professor Dr. Algirdas Vaskelis on the occassion of his 70th birthday.