环糊精聚合物与苯醌的分子包合作用及其在酶电极中的应用

研究了水溶性环糊精预聚合物的存在对苯醌/氢醌体系在铂电极上氧化还原行为的影响, 根据伏安曲线讨论了该预聚合物与苯醌的分子包合作用。环糊精预聚合物与戊二醛缩聚反应而形成的不溶性聚合物膜用于葡萄糖氧化酶的固定化, 以制得新型的第二代葡萄糖电极。由于分子包合作用, 作为电子受体的苯醌在含酶的环糊精聚合物膜中具有较高的浓度, 从而加速了固定化酶的电子传递。测定了酶电极上BQ反应的动力学参数。     

孔蛋白-磷脂仿生膜的葡萄糖氧化酶电化学

采用孔蛋白（MspA）和双肉豆蔻磷脂酰胆碱（DMPC）在玻碳（GC）基底表面成功构建有仿生特性的纳米通道膜,同时将葡萄糖氧化酶（GOD）修饰于膜上. 使用循环伏安法研究GOD/MspA-DMPC/GC电极的GOD直接电化学过程以及其对氧气和葡萄糖的响应. 研究发现,MspA与DMPC形成的仿生纳米通道膜内,GOD在接近生物体系FAD/FADH标准电位处实现了自身两质子、两电子表面控制的电化学反应. MspA与DMPC的仿生纳米通道膜体系为GOD提供了理想活性环境.     

FeFe]-hydrogenase-catalyzed H2 production in a photoelectrochemical biofuel cell

The Clostridium acetobutylicum [FeFe]-hydrogenase HydA has been investigated as a hydrogen production catalyst in a photoelectrochemical biofuel cell. Hydrogenase was adsorbed to pyrolytic graphite edge and carbon felt electrodes. Cyclic voltammograms of the immobilized hydrogenase films reveal cathodic proton reduction and anodic hydrogen oxidation, with a catalytic bias toward hydrogen evolution. When corrected for the electrochemically active surface area, the cathodic current densities are similar for both carbon electrodes, and approximately 40% of those obtained with a platinum electrode. The high surface area carbon felt/hydrogenase electrode was subsequently used as the cathode in a photoelectrochemical biofuel cell. Under illumination, this device is able to oxidize a biofuel substrate and reduce protons to hydrogen. Similar photocurrents and hydrogen production rates were observed in the photoelectrochemical biofuel cell using either hydrogenase or platinum cathodes.     

Direct electrochemistry of glucose oxidase immobilized on a hexagonal mesoporous silica-MCM-41 matrix

The direct electrochemistry of glucose oxidase (GOD) immobilized on a hexagonal mesoporous silica modified glassy carbon electrode was investigated. The adsorbed GOD displayed a pair of redox peaks with a formal potential of -417 mV in 0.1 M pH 6.1 phosphate buffer solution (PBS). The response showed a diffusion-controlled electrode process with a two-electron transfer coupled with a two-proton transfer reaction process. GOD immobilized on a hexagonal mesoporous silica retained its bioactivity and stability. In addition, the immobilized GOD could electrocatalyze the oxidation of glucose to gluconlactone by taking ferrocene monocarboxylic acid (FMCA) as a mediator in N(2) saturated solutions, indicating that the electrode may have the potential application in biosensors to analyze glucose. The sensor could exclude the interference of commonly coexisted uric acid, p-acetaminophenol and ascorbic acid and diagnose diabetes very fast and sensitively. This work demonstrated that the mesoporous silica provided a novel matrix for protein immobilization and the construction of biosensors.     

介孔碳修饰玻碳电极上葡萄糖氧化酶的直接电化学

使用简单的方法将葡萄糖氧化酶(GOD)固定在介孔碳(Mesoporous Carbon)修饰的玻碳电极(GCE)表面.循环伏安测试表明:修饰电极上的GOD在0.1mol/L磷酸缓冲溶液(PBS)(pH=7.1)中发生了准可逆的氧化还原反应,其克式量电位为-0.4294 V,并且该电化学反应包含有两电子两质子的传递.在氮气饱和的情况下,以羧基二茂铁作为电子传递中介体,GOD能将葡萄糖彻底催化氧化,可见介孔碳修饰电极上的GOD保持了其生物学活性.     

Application of polymaleimidostyrene as a convenient immobilization reagent of enzyme in biosensor

Sulfhydryl groups of glucose oxidase (GOD) were reacted with maleimide groups of polymaleimidostyrene (PMS) which was coated onto the porous carbon sheet, and the carbon sheet immobilized by GOD was combined with an oxygen electrode to fabricate a glucose sensor. The activity of thiolated GOD immobilized to PMS is much larger than that of native GOD immobilized to PMS. The good linear relationship of glucose and oxygen current response was obtained in a concentration range from 0.1 to 2 mM and upper limit of linear range was found to be 3.0 mM. The immobilized GOD activity is highly dependent on pH at immobilization and the maximum activity was obtained at pH 5.5, probably because the SH groups of GOD that are indispensable for generation of enzyme activity is not exposed at this pH. It was found that PMS is very effective reagent to immobilize enzyme strongly via covalent bond, because high density of maleimide groups of PMS can catch not only exposed SH groups but also buried SH groups.     

Reagentless Glucose Biosensor Based on the Direct Electrochemistry of Glucose Oxidase on Carbon Nanotube‐Modified Electrodes

The direct electrochemistry of glucose oxidase (GOD) was revealed at a carbon nanotube (CNT)‐modified glassy carbon electrode, where the enzyme was immobilized with a chitosan film containing gold nanoparticles. The immobilized GOD displays a pair of redox peaks in pH 7.4 phosphate buffer solutions (PBS) with the formal potential of about ?455 mV (vs. Ag/AgCl) and shows a surface‐controlled electrode process. Bioactivity remains good, along with effective catalysis of the reduction of oxygen. In the presence of dissolved oxygen, the reduction peak current decreased gradually with the addition of glucose, which could be used for reagentless detection of glucose with a linear range from 0.04 to 1.0 mM. The proposed glucose biosensor exhibited high sensitivity, good stability and reproducibility, and was also insensitive to common interferences such as ascorbic and uric acid. The excellent performance of the reagentless biosensor is attributed to the effective enhancement of electron transfer between enzyme and electrode surface by CNTs, and the biocompatible environment that the chitosan film containing gold nanoparticles provides for immobilized GOD.     

Poly(acrylic acid)-silicon Hybrids Prepared via a RAFT-mediated Process and Covalent Immobilization of Glucose Oxidase

A surface modification technique was proposed for the modification of silicon surface with glucose oxidase (GOD). The silicon surface was first graft copolymerized with acrylic acid (AAc) via surface-initiated reversible addition-fragmentation chain-transfer (RAFT)-mediated process. With the aid of a water-soluble carbodiimide, GOD was then covalently immobilized on the silicon surface through the amide linkage between the amino group of GOD and the carboxyl group of the grafted AAc polymer. The changes in the surface composition after polymer grafting and enzyme immobilization on the silicon surface were investigated using X-ray photoelectron spectroscopy (XPS). The amount of GOD immobilized could be varied by changing the thickness of the polymer layer and the immobilization time. The GOD-functionalized silicon hybrids are potential useful in the application of the silicon-based biosensors.     

Glucose oxidase/colloidal gold nanoparticles immobilized in Nafion film on glassy carbon electrode: Direct electron transfer and electrocatalysis

The direct electron transfer of glucose oxidase (GOD) was achieved based on the immobilization of GOD/colloidal gold nanoparticles on a glassy carbon electrode by a Nafion film. The immobilized GOD displayed a pair of well-defined and nearly reversible redox peaks with a formal potential (Eo ') of -0.434 V in 0.1 M pH 7.0 phosphate buffer solution and the response showed a surface-controlled electrode process. The dependence of Eo ' on solution pH indicated that the direct electron transfer reaction of GOD was a two-electron-transfer coupled with a two-proton-transfer reaction process. The experimental results also demonstrated that the immobilized GOD retained its electrocatalytic activity for the oxidation of glucose. So the resulting modified electrode can be used as a biosensor for detecting glucose.     

Direct electron transfer with glucose oxidase immobilized in an electropolymerized poly( N-methylpyrrole) film on a gold microelectrode

Direct electron transfer between active glucose oxidase (GOD) and a gold electrode was obtained when GOD was immobilized in poly(N-methylpyrrole) electrochemically prepared on the gold electrode. When electropolymerization was accomplished at 50 °C, after glucose addition, the cyclic voltammograms showed an increased oxidation peak at ca. ?0.45 V vs. Ag/AgCl. This potential corresponds to the oxidation potential for FADH₂. Although the GOD becomes much less selective, a glucose-dependent current response is obtained.     

Low‐Potential Detection of Glucose with a Biosensor Based on the Immobilization of Glucose Oxidase on Polymer/Manganese Oxide Layered Nanocomposite

A nanocomposite with poly(diallyldimethylammonium), PDDA, intercalated between manganese oxide layers is constructed on a graphite electrode surface through one‐step electrodeposition and used to adsorb glucose oxidase (GOD). The immobilized GOD displays a pair of stable and quasireversible redox peaks with a formal potential of ?468 mV in pH 7.0 buffer solutions and exhibits excellent electrocatalysis to the reduction of oxygen. In the presence of dissolved oxygen, the reduction peak current decreased gradually with the addition of glucose, indicating that the immobilized GOD kept its bioactivity. Thus a reagentless biosensor for glucose at a low detection potential was established. The linear concentration range is from 0.02 to 2.78 mM with a detection limit of 9.8 μM. The proposed glucose biosensor was insensitive to common interferences such as ascorbic and uric acids etc.     

Facile Fabrication of a Graphene‐based Electrochemical Biosensor for Glucose Detection

A simple and effective glucose biosensor based on immobilization of glucose oxidase (GOD) in graphene (GR)/Nafion film was constructed. The results indicated that the immobilized GOD can maintain its native structure and bioactivity, and the GR/Nafion film provides a favorable microenvironment for GOD immobilization and promotes the direct electron transfer between the electrode substrate and the redox center of GOD. The electrode reaction of the immobilized GOD shows a reversible and surface‐controlled process with the large electron transfer rate constant (k_s) of 3.42±0.08 s^?1. Based on the oxygen consumption during the oxidation process of glucose catalyzed by the immobilized GOD, the as‐prepared GOD/GR/Nafion/GCE electrode exhibits a linear range from 0.5 to 14 mmol·L^?1 with a detection limit of 0.03 mmol·L^?1. Moreover, it displays a good reproducibility and long‐term stability.     

Synthesis and dilute aqueous solution properties of ester functionalized cationic gemini surfactants having different ethylene oxide units as spacer

New series of ester functionalized quaternary ammonium gemini surfactants having different ethylene oxide units as spacer have been synthesized and investigated for their aggregation behavior and thermodynamic properties of micellization by surface tension, conductivity, and fluorescence methods. The critical micelle concentration (cmc) of these gemini surfactants increases with the increase in the length of polar hydrophilic ethylene oxide spacer. The micellization process has been found to be entropy-driven and dependent on both the tendency of the hydrophobic group of the surfactants to transfer from aqueous environment to interior of micelle as well as the rearrangement of flexible ester-linked ethylene oxide units (hydrophilic spacer) into aqueous phase. The polar ester functional groups and pairs of nonbonding electrons on oxygen atom of ethylene oxide spacer form hydrogen bonding with water molecules enhancing their solubility in aqueous system.     

Novel Composite of Multiwalled Carbon Nanotubes and Gold Nanoparticles Stabilized by Chitosan and Hydrophilic Ionic Liquid for Direct Electron Transfer of Glucose Oxidase

A novel composite was fabricated through dispersing multiwalled carbon nanotubes (MWNTs) in gold nanoparticle (GPs) colloid stabilized by chitosan and ionic liquid (i.e., 1‐butyl‐3‐methylimidazolium tetrafluoroborate, BMIMBF₄). Transmission electron microscopy (TEM) experiment showed that the GPs highly dispersed on the MWNTs probably due to the electrostatic interaction among GPs, MWNTs and the imidazolium cation of BMIMBF₄. X‐ray photoelectron spectroscopy (XPS) indicated that thus‐formed gold nanostructure was mediated by BMIMBF₄. When glucose oxidase (GOD) was immobilized on the composite (MWNTs‐GPs) its ultraviolet‐visible absorption spectrum kept almost unchanged. The immobilized GOD coated glassy carbon electrode (GOD/MWNTs‐GPs/GC) exhibited a pair of well‐defined peaks in 0.10 M pH 7.0 phosphate buffer solution (PBS), with a formal potential of ?0.463 V (vs. SCE). The electrochemical process involved two‐electron transfer. The electron transfer coefficient was ca.0.56 and the electron transfer rate constant was 9.36 s^?1. Furthermore, the immobilized GOD presented good catalytic activity to the oxidation of glucose in air‐saturated PBS. The K_m and I_m values were estimated to be 13.7 μM and 0.619 μA. The GOD/MWNTs‐GPs/GC electrode displayed good stability and reproducibility.     

A combination of voltammetry of immobilized microparticles and carbon black-based crosslinked chitosan films deposited on glassy carbon electrode for the quantification of hydroquinone in dermatologic cream samples

New progress in the application of voltammetry of immobilized microparticles (VIM) technique in electroanalytical chemistry is reported in this work through the determination of hydroquinone in dermatologic cream samples. The designed electrode was based on a glassy carbon electrode modified with a crosslinked chitosan film containing immobilized carbon black nanoparticles and hydroquinone standards or sample. The electrochemical features of immobilized hydroquinone were explored, which a fast electron transfer kinetic was verified from the perfect reversible redox behavior of this molecule. All the experimental conditions were optimized, including supporting electrolyte condition (composition, pH, and ionic strength) and technical parameters of differential pulse voltammetry (DPV). Under the optimized experimental conditions, the analytical curve was linear by a wide concentration range from 2.7 to 43 ng, with detection and quantification limits of 0.045 and 0.15 ng, respectively. Two commercial dermatologic cream samples were successfully immobilized and analyzed using the proposed VIM procedure, and the results were similar to those recorded by a spectrophotometric comparative procedure. Our set of results represents a unique and exciting advance in the scenario of electroanalytical chemistry for future applications.     

Direct electrochemistry and reagentless biosensing of glucose oxidase immobilized on chitosan wrapped single-walled carbon nanotubes

Single-walled carbon nanotubes (SWCNTs) selectively wrapped by a water-soluble, environmentally friendly, biocompatible polymer chitosan (CHI) were employed for the construction of a bioelectrochemical platform for the direct electron transfer (DET) of glucose oxidase (GOD) and biosensing purposes. Scanning electron microscopy and Raman spectroscopy were used to investigate the properties of the SWCNT-CHI film. The results show that the preferentially wrapped small-diameter SWCNTs are dispersed within the CHI film and exist on the surface of the electrode as small bundles. The DET between GOD and the electrode surface was observed with a formal potential of about ca. -460 mV vs. SCE in phosphate buffer solution. The heterogeneous electron transfer rate constant and the surface coverage of GOD are estimated to be 3.0 s(-1) and 1.3 x 10(-10)mol/cm(2), respectively. The experimental results demonstrate that the immobilized GOD retains its catalytic activity towards the oxidation of glucose. Such a GOD/SWCNT-CHI film-based biosensor not only exhibits a rapid response time, a wide linear rang and a low detection limits at a detection potential of -400 mV but also shows the effective anti-interference capability. Significantly improved analytical capabilities of the GOD/SWCNT-CHI/GC electrode could be ascribed to the unique properties of the individual SWCNTs and to the biocompatibility of CHI.     

Direct electrochemistry of glucose oxidase immobilized on porous carbon nanofiber/room temperature ionic liquid/chitosan composite film and its biosensing application

The direct electron transfer of glucose oxidase (GOD) immobilized on a composite matrix based on porous carbon nanofibers (PCNFs), room-temperature ionic liquid (RTIL), and chitosan (CHIT) underlying on a glassy carbon electrode was achieved. The combination of the PCNFs, RTIL, and CHIT provided a suitable microenvironment for GOD to transfer electron directly. In deaerated buffer solutions (pH 7.0), the cyclic voltammetry of the GOD/PCNFs/RTIL/CHIT composite films showed a pair of well-defined redox peaks with the formal potential of −0.45 V (vs. SCE). The synergistic effort of the PCNFs, RTIL, and CHIT also promoted the stability of GOD in the composite film and retained its bioactivity.     

Design of a bioelectrocatalytic electrode interface for oxygen reduction in biofuel cells based on a specifically adapted Os-complex containing redox polymer with entrapped Trametes hirsuta laccase

The design of the coordination shell of an Os-complex and its integration within an electrodeposition polymer enables fast electron transfer between an electrode and a polymer entrapped high-potential laccase from the basidiomycete Trametes hirsuta. The redox potential of the Os^3+/2+-centre tethered to the polymer backbone (+ 720 mV vs. NHE) is perfectly matching the potential of the enzyme (+ 780 mV vs. NHE at pH 6.5). The laccase and the Os-complex modified anodic electrodeposition polymer were simultaneously precipitated on the surface of a glassy carbon electrode by means of a pH-shift to 2.5. The modified electrode was investigated with respect to biocatalytic O₂ reduction to H₂O. The proposed modified electrode has potential applications as biofuel cell cathode.     

生物功能电极I: GOD修饰电极的电化学活性

以二环己基碳化二亚胺为活化剂将葡萄糖氧化酶(GOD)共价键接在玻碳电极上, 伏安实验观察到酶与电极基体的直接电子传递, 有观电子传递速度常数约为1s^-^1, 过程归因于全酶中辅基FAD的氧化还原转变。Ag^+离子的存在强烈地阻碍酶辅基的还原, 这与该离子抑制酶活性的机理可能有联系。Ag^+的抑制作用可由EDTA处理或电化学处理而解除, GOD电极对氧和苯醌的电还原有催化作用。测定了苯醌同还原态GOD的化学反应速度常数, 并讨论用苯醌代替氧作为生物电催化中的电子传递体的优点。     

Graphene-based modified electrode for the direct electron transfer of Cytochrome c and biosensing

Chitosan-dispersed graphene nano-flakes were prepared by a chemical route to reduce graphene oxide and dispersed fully in water to form a stable black aqueous solution. The as-prepared graphene nano-flakes were successfully immobilized on glassy carbon electrode to construct a graphene modified electrode. Cytochrome c was adsorbed tightly on the surface of the modified electrode and the direct electron transfer of Cytochrome c was achieved. Cytochrome c on the surface of electrode maintains its bioactivity and shows an enzyme-like activity for the reduction of nitric oxide, displaying a potential application for the fabrication of novel biosensors to sense nitric oxide. This research will enlarge the applications of graphene-based materials in biosensor field.