Synthesis and characterization of electron beam evaporated LiCoO<Subscript>2</Subscript> thin films

LiCoO₂ thin films were prepared by electron beam evaporation technique using LiCoO₂ target with Li/Co ratio 1.1 in an oxygen partial pressure of 5 × 10⁻⁴ mbar. The films prepared at substrate temperature T _s < 573 K were amorphous in nature, and the films prepared at T _s > 573 K exhibited well defined (104), (101), and (003) peaks among which the (104) orientation predominates. The X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma (ICP) data revealed that the films prepared in the substrate temperature range 673–773 K are nearly stoichiometric. The grain size increases with an increase of substrate temperature. The Co–e_g absorption bands, are empty and their peak position lies at around 1.7 eV above the top to the Co–t_2g bands. The fundamental absorption edge was observed at 2.32 eV. The films annealed at 1,023 K in a controlled oxygen environment exhibit (104) out plane texture with large grains. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006     

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Structural investigation on PEO-based polymer electrolytes dispersed with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

Thin solid polymer electrolytes based on polyethylene oxide (PEO) and silver triflate (AgCF₃SO₃) dispersed with various concentrations of aluminum oxide (Al₂O₃) nanoparticles have been prepared by solution casting technique. These thin polymer films are found to have thickness of the order of 30 to 100 μm. The X-ray diffraction (XRD) patterns have indicated the amorphous nature of the polymer electrolyte. The differential scanning calorimeter (DSC) traces showed slight change in the glass transition temperature (T _g) whereas the degree of crystallization (X _c) decreases markedly due to the addition of alumina nanoparticles. Fourier transform infrared (FTIR) spectral analysis of all these samples has revealed the presence of absorption bands around 1,000 cm⁻¹; thus indicating the complexation of silver ions with oxygen in PEO. Employing the Wagner’s polarization technique as the standard method, the total ionic transference number for the complexed polymer electrolyte was found to be approximately unity thereby revealing that the significant contribution to electrical conduction was due to ions only. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006     

Anomalous absorption in H<Subscript>2</Subscript>CN and CH<Subscript>2</Subscript>CN molecules

Structures of H₂CN and CH₂CN molecules are similar to that of H₂CO molecule. The H₂CO has shown anomalous absorption for its transition 1₁₁–1₁₀ at 4.8 GHz in a number of cool molecular clouds. Though the molecules H₂CN and CH₂CN have been identified in TMC-1 and Sgr B2 through some transitions in ortho as well as in para species, here we have investigated the condition under which transitions 1₁₁–1₁₀ and 2₁₂–2₁₁ of these molecules may show anomalous absorption. For the present investigation, we have calculated energy levels and radiative transition probabilities. However, we have used scaled values for collisional rate coefficients. We found that relative values of collisional rate coefficients can produce the required anom-alous absorption in 1₁₁–1₁₀ and 2₁₂–2₁₁ transitions in the molecules.      

Influence of the sample orientation in Sn<Subscript>2</Subscript>P<Subscript>2</Subscript>S<Subscript>6</Subscript> crystals on the hydrostatic piezoelectric coefficients

The influence of the sample orientation on the effective value of the hydrostatic piezoelectric coefficients d _h ⁽ⁱ⁾ of Sn₂P₂S₆ crystals has been studied. The hydrostatic piezoelectric coefficients d _h ⁽¹⁾ and d′ _h ⁽³⁾ , were measured, d _h ⁽¹⁾ =(244±3) pC/N and d′ _h ⁽³⁾ =(92±1) pC/N. The hydrostatic piezoelectric coefficient d _h ⁽³⁾ for orthogonal axis system was calculated to be d _h ⁽³⁾ =(87±2) pC/N. The, optimal orientation of the sample has been found as (Xy l)−20°-cut. Maximal value of the effective hydrostatic piezoelectric coefficient d _h ⁽¹⁾ equals 260 pC/N. Double rotated samples were also studied. The orientation of the samples insensitive to the pressure has been found. The theoretical mean value of hydrostatic piezoelectric coefficient (d _h ) _mean corresponding to randomly oriented Sn₂P₂S₆ grains in a poled composite has been calculated to be (d _h ) _mean =136 pC/N.     

One-step synthesis of colloidal Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> and γ-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles at room temperature

A facile room-temperature synthesis has been developed to prepare colloidal Mn₃O₄ and γ-Fe₂O₃ nanoparticles (5 to 25 nm) by an ultrasonic-assisted method in the absence of any additional nucleation and surfactant. The morphology of the as-prepared samples was observed by transmission electron microscopy. High-resolution transmission electron microscopy observations revealed that the as-synthesized nanoparticles were single crystals. The magnetic properties of the samples were investigated with a superconducting quantum interference device magnetometer. The possible formation process has been proposed.     

Synthesis of ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> complex substrates and growth of GaN films

With the solid phase reaction between pulsed-laser-deposited (PLD) ZnO film and α-Al₂O₃ substrate, ZnAl₂O₄/α-Al₂O₃ complex substrates were synthesized. X-ray diffraction (XRD) spectra show that as the reaction proceeds, ZnAl₂O₄ changes from the initial (111)-oriented single crystal to poly-crystal, and then to inadequate (111) orientation. Corresponding scanning electron microscope (SEM) images indicate that the surface morphology of ZnAl₂O₄ transforms from uniform islands to stick structures, and then to bulgy-line structures. In addition, XRD spectra present that ZnAl₂O₄ prepared at low temperature is unstable at the environment of higher temperature. On the as-obtained ZnAl₂O₄/α-Al₂O₃ substrates, GaN films were grown without any nitride buffer using light-radiation heating low-pressure MOCVD (LRH-LP-MOCVD). XRD spectra indicate that GaN film on this kind of complex substrate changes fromc-axis single crystal to poly-crystal as ZnAl₂O₄ layer is thickened. For the single crystal GaN, its full width at half maximum (FWHM) of X-ray rocking curve is 0.4°. Results indicate that islands on thin ZnAl₂O₄ layer can promote nucleation at initial stage of GaN growth, which leads to the (0001)-oriented GaN film.     

First-principles calculations on the electronic structure and optical properties of BaSi<Subscript>2</Subscript>

The electronic structure, densities of states and optical properties of the stable orthorhombic BaSi₂ have been calculated using the first-principle density function theory and pseudopotential method. The results show that BaSi₂ is an indirect semiconductor with the band gap of 1.086 eV, the valence bands of BaSi₂ are mainly composed of Si 3p, 3s and Ba 5d, and the conduction bands are mainly composed of Ba 6s, 5d as well as Si 3p. The static dielectric function ɛ ₁(0) is 11.17, the reflectivity n ₀ is 3.35, and the biggest peak of the absorption coefficient is 2.15×10₅ cm⁻¹. Supported by the National Natural Science Foundation of China (Grant Nos. 60566001 and 60766002), the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20050657003), the Scientific Research Foundation for the Returned Overseas Chinese Scholars, Ministry of Education of China (Grant No. (2005)383), the Specialized Fund of Nomarch for Excellent Talent of Science and Technology of Guizhou Province (Grant No. Z053114), the Scientific and Technological Projects for the Returned Overseas of Guizhou Province (Grant No. (2004)03), and the Top Talent’s Scientific Research Project of Organization Department of Guizhou Province (Grant No. Z053123)     

First-principles study on the electronic structure and optical properties of CrSi<Subscript>2</Subscript>

Using the first principle methods based on the plane-wave pseudo-potential theory, band structure, density of states and optical properties of CrSi₂ were studied. The calculation of band structure shows that CrSi₂ is an indirect semiconductor whose band gap is 0.353 eV. Density of states is mainly composed of 3d electron of Cr and 3p electron of Si. Dielectric function, refractive index, reflectivity, and absorption coefficient of CrSi₂ are also calculated. The calculation results of optical properties are in agreement with the experiments. Supported by the National Natural Science Foundation of China (Grant No. 60566001), the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No. 20050657003), the Scientific Research Foundation for the Returned Overseas Chinese Scholars, Ministry of Education of China (Grant No. (2005)383), the Program for Excellent Young Talents of Guizhou Province (No. 20050528), the Specialized Nomarch Research Fund for the Excellent Science and Technology and Education Talent’s Projects of Guizhou Province, the Scientific and Technological Projects for the Returned Overseas Chinese Scholars, Guizhou Province (Grant No. (2004)03), and the Top Talent’s Scientific Research Project of Organization Department of Guizhou Province.     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

VUV luminescence of Er<Superscript>3+</Superscript> ions in LiYF<Subscript>4</Subscript> and BaY<Subscript>2</Subscript>F<Subscript>8</Subscript> crystals

Vacuum ultraviolet luminescence of Er³⁺ ions in LiYF4 and BaY₂F₈ crystals has been investigated. It is revealed that under excitation by 193 nm radiation from an ArF excimer laser the interconfigurational 5d–4f radiative transitions in Er³⁺ ions are observed. It is shown that from the LiYF₄:Er crystal only the spin-forbidden luminescence (λ = 165 nm) is detected, whereas both the spin-forbidden (λ = 169 nm) and spin-allowed (λ = 160.5 nm) components are observed from the BaY₂F₈:Er crystal.     

Surface morphology of PrBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>7-δ</Subscript> single crystals after the long-lasting high-temperature reduction

The results of the detailed scanning electron microscopy study of PrBa₂Cu₃O_7-δ single crystals after the long-lasting high-temperature post-growth treatment are reported. The presence of the unstable decomposition products on the crystal surface indicates that the onset of superconductivity must be related to the structural transformations in the bulk (approximately 20% of the total volume of the examined crystals). The time-dependent character of the superconductivity in the Pr-123 crystals could be attributed to the migration of defects in the Pr−Ba sublattice from the bulk toward the surface.     

Characterization of Y<Subscript>2</Subscript>BaCuO<Subscript>5</Subscript> nanoparticles synthesized by nano-emulsion method

Nanoscale yttrium–barium–copper oxide (Y₂BaCuO₅, Y211) particles were synthesized using the emulsion method and the solution method. The basic water-in-oil (w/o) emulsion system consisted of n-octane (continuous oil phase), cetyltrimethylammonium bromide (cationic surfactant), butanol (cosurfactant) and water. The composition of the emulsion system was varied and characterized by measuring the conductivity of the solutions and droplet size. The droplet size of emulsion was determined by using the dynamic light scattering method. The water content, cosurfactant content, and surfactant/n-octane ratio affected the droplet size which was in the range of 3–8 nm, and hence the w/o emulsion system was referred to as a nano-emulsion system. A model was used to verify the droplet size. The influence of salt (Y₂(NO₃)₃) content on the droplet size was investigated and the addition of salt reduced the droplet size. The effects of reaction time and temperature on the Y211 particle sizes were also investigated. The particles were characterized using the TEM, SEM, and XRD. Nanoparticles produced by the nano-emulsion method were calcined at 850°C to form the Y211 phase as compared to solid state processing temperature of 1050°C. Based on the TEM analysis, the average diameter of the Y211 particles produced using the nano-emulsion method was in the range of 30–100 nm. The effect of adding 15% Y211 nanoparticles to the superconductor YBCO-123 as flux pinning centers, was investigated, and the transition temperature was reduced by 3 K.     

Investigation on structural characteristics of PVDF–AgCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite solid polymer electrolyte system

There has been an increasing interest towards the incorporation of nanosize ceramic fillers in polymer electrolytes. Solid polymer electrolytes based on polyvinylidene fluoride (PVDF), silver triflate (AgCF₃SO₃), and x wt% of aluminum oxide (Al₂O₃) nanopowders (where x = 1, 3, 5, and 10, respectively) have been prepared using solution casting technique. The structural characteristics of these thin film specimens were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) patterns at room temperature. The appearance of new absorption bands and gradual shifts observed in some characteristic peaks confirmed the complex formation between polyvinylidene fluoride and silver triflate. Furthermore, the addition of nanosized filler Al₂O₃ has also indicated the interaction of the filler with the polymer salt complex. The XRD patterns obtained for all these samples in the 2θ range 10° to 70° showed the amorphous nature of these samples. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006.     

Thermoelectric properties of Pb<Subscript>0.22</Subscript>Sn<Subscript>0.78</Subscript>Te<Ge> solid solution

Temperature dependences of thermoelectric parameters of the Pb_0.22Sn_0.78Te〈Ge(0.5 at%)〉 solid solution in the temperature range 140–440 K are investigated with the purpose to determine the perspectiveness of these solutions as a material for thermoelements.     

Study of structural phase transitions in YBa<Subscript>2</Subscript>Cu<Subscript>3</Subscript>O<Subscript>6+δ</Subscript> by x-ray photoelectron spectroscopy

We have used x-ray photoelectron spectroscopy to investigate the charge state of oxygen found in the basal structural plane of YBa₂Cu₃O₆+γ.. We have observed a change in this state after thermal treatment, with a transition to the adjacent structural phase region. We have shown that changes in the charge state of oxygen can be used as an indicator of structural changes occurring in YBa₂Cu₃O₆+δ.. We have found that the rate of structural relaxation yttrium barium cuprate depends on the amount of structural water it contains. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 2, pp. 195–198, March–April, 2007.     

Accuracy in determination of the temperature and partial pressure of CO<Subscript>2</Subscript> in CO<Subscript>2</Subscript>:N<Subscript>2</Subscript>:H<Subscript>2</Subscript>O:NO<Subscript>2</Subscript> mixtures by multiple-frequency laser probing

We present the results of analysis of the errors introduced by hot-band transitions 11¹0-01¹1, 03¹0-01¹1, 12⁰0-12⁰1 of the CO₂ molecule and the absorption lines of the H₂O and NO₂ molecules in determination of the temperature and partial pressure of CO₂, included in the gas mixture CO₂: N₂:H₂O: NO₂ at atmospheric pressure, by multiple-frequency laser probing using a CO₂ laser tunable over the lines of the 00⁰1-[10⁰0,02⁰0]_I,II ground-state laser transitions. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 6, pp. 810–815, November–December, 2007.     

Effect of excess Y<Subscript>2</Subscript>O<Subscript>3</Subscript> addition on the physical properties of melt processed YBCO bulks

The YBCO superconductors with Y₂O₃ addition were prepared by a modified melt textured process and the effects of excess Y₂O₃ addition on the physical properties of melt textured YBCO have been investigated. It is found that the melt temperature of YBCO samples decreases drastically with the increasing Y₂O₃, and the maximum levitation forces are drastically different for samples with different Y₂O₃ addition. It is also found that the optimal Y₂O₃ addition to YBCO is about 10wt%. Considering the microstructure and the starting composition, the results are well discussed and interpreted.     

Structural relaxation of Zr<Subscript>41</Subscript>Ti<Subscript>14</Subscript>Cu<Subscript>12.5</Subscript>Ni<Subscript>10</Subscript>Be<Subscript>22.5</Subscript> bulk metallic glass under high pressure

Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG) is annealed at 573 K under 3 GPa and its structural relaxation is investigated by X-ray diffraction, ultrasonic study, compression as well as sliding wear measurements. It is found that after the ZrTiCuNiBe BMG sample was annealed under high pressure, the mechanical properties were improved. Moreover, theBMG with relaxed structure exhibits markedly different acoustic properties. These results are attributed to the fact that relaxation under high-pressure results in a microstructural transformation in the BMG.     

Absorption by CS<Subscript>2</Subscript> molecules on “hot” band emission lines from a TEA CO<Subscript>2</Subscript> laser

We have measured absorption of emission from a TEA CO₂ laser, lasing on hot band lines, in pure CS₂ and a mixture of CS₂ with air, and we have determined the optimal lines for optical excitation. Numerical modeling has shown that as the peak intensity of the pump radiation is increased, we observe absorption saturation, the extent of which decreases as the pressure increases. The major factor responsible for absorption saturation is the “rotational bottleneck” effect. Depending on the peak intensity of the radiation, addition of a buffer gas can lead to an increase or decrease in the absorption. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 1, pp. 61–66, January–February, 2007.