圆柱扁壳的非线性动力响应的样条加权残值分析

本文对圆柱扁壳的非线性动力响应的问题,利用加相对加权残值法的子域方法将唐奈尔方程转化成时间因子作为示知函数的控制方程,运用样条配点法发成若干段,且保证在每时间段均连续将算例结果与有关文献比较的同时,还运用ＯＤＥ ＳＯＶＶＥＲ－ＣＯＬＳＹＳ程序作数值比较。     

中厚板屈曲的加权残值方法

用加权残值方法分析了矩形中厚板的屈曲问题。试函数和权函数依据短梁函数进行构造。结果良好。     

轴压圆柱壳后屈曲的有限元分析

采用流动的曲线坐标建立了大位移下的样条曲壳元，利用它分析了轴压圆柱壳的后屈曲问题。一个跨越和求取分支点的技巧和对弧长法的一个改进在文中提出。计算所得的载荷－轴向缩短曲线较解析解更接近于实验结果，所得的后屈曲波形也和实验相当符合。     

小波加权残值法在斜板后屈曲上的应用

将斜板在大挠度理论下的平衡方程和变形协调方程转化为斜坐标系下的表达式,并无量纲化,对于四边固支斜板,选用尺度小于1的二维bior3.1重构尺度函数与小波作试函数,满足板在平面外的几何与自然边界条件,利用小波-Galerkin法将板的无量纲平衡控制方程与变形协调方程转化为两个非线性方程组,从而将后屈曲路径的求解转化为两非线性方程组的求解问题.以载荷作为迭代步长,采用Newton-Raphson迭代算法求得承受单向压缩四边固支斜板在不同边长比、不同斜角下的后屈曲平衡路径及四级渐近解.     

数学规划加权残值法分析薄板与薄壳的几何非线性问题

使用数学规划加权残值涯分析了薄板大挠度及薄壳的非线性稳定问题。在两者应变协调方程严格满足的情况下,论证并利用平衡方程的单调性,建立数学规划问题,首先得到无布载荷四边简支方板中心挠度的最小上界及最大下界,经典Ｌｅｖｙ解位基其间。     

卷积型加权残值法求解薄壳的动力学问题

板壳等弹性体,受到动荷载作用时,其动力分析问题是比较重要且难于解决的．利用卷积型加权残值法,推导出Gurtin变分原理,并应用卷积型加权残值法计算了薄壳的动力学问题,为计算薄壳的结构动力学问题提供了一种有效的方法．     

变角度纤维复合材料圆柱壳的轴压屈曲

变角度纤维复合材料的纤维方向角可沿铺层面内连续变化,因此相应结构的性能具有更高的设计灵活性和更大的优化空间．本文假设纤维方向角沿圆柱壳的轴向呈正弦函数变化,对变角度纤维复合材料圆柱壳在两端简支边界条件下的轴压屈曲问题进行研究．基于Donnell经典壳体理论,推导变角度纤维复合材料圆柱壳的前屈曲控制方程并运用伽辽金法进行求解,然后采用瑞利里兹法求解屈曲问题．通过和现有文献及有限元数值结果的对比,验证了本文模型的收敛性和正确性,通过数值算例分析了纤维起始角和终止角的变化对圆柱壳的屈曲临界荷载的影响．本文的研究结果可为变角度纤维复合材料圆柱壳的分析和设计提供一定的参考．     

圆柱约束下细长压杆屈曲及后屈曲行为

研究了轴向力作用下受圆柱横向约束的弹性杆的屈曲和后屈曲行为。通过有限元模拟,分析了细长压杆发生正弦和螺旋屈曲的轴向临界力,提出了正弦和螺旋屈曲临界点判定方法,且与文献结果比较验证了分析的正确性。同时考察了长细比和边界条件等因素对临界力的影响。结果表明正弦屈曲临界力和螺旋屈曲临界力随杆的长细比减小而增大。杆在一定长度范围内,端部约束条件对临界屈曲载荷及模态的影响不可忽略;当杆的长度足够长时,可以忽略边界条件对临界载荷的影响。     

外压加筋圆柱壳总体屈曲Koiter——边界层奇异摄动法

将Ｋｏｉｔｅｒ理论和奇异摄动理论中的边界层法相结合处理加筋圆柱壳无因次化非线性边界层型Ｋａｒｍａｎ－Ｄｏｎｎｅｌ方程由分支点和边界层导致的双重奇异性，提出外压加筋圆柱壳总体屈曲Ｋｏｉｔｅｒ—边界层奇异摄动法。从摄动意义上分析边界条件，前屈曲非线性和初始几何缺陷对外压加筋圆柱壳屈曲载荷的影响。算例表明，本方法具有良好的计算效率和计算精度，与数值解相比更能揭示内在影响规律。     

Buckling and Postbuckling of Laminated Thin Cylindrical Shells under Hygrothermal Environments

ＩｎｔｒｏｄｕｃｔｉｏｎＩｎｒｅｃｅｎｔｙｅａｒｓ,ｆｉｂｅｒ＿ｒｅｉｎｆｏｒｃｅｄｃｏｍｐｏｓｉｔｅｌａｍｉｎａｔｅｄｓｈｅｌｌｓｔｒｕｃｔｕｒｅｓａｒｅｗｉｄｅｌｙｕｓｅｄｉｎｔｈｅａｅｒｏｓｐａｃｅ ,ｍａｒｉｎｅｉｎｄｕｓｔｒｙ ,ａｕｔｏｍｏｂｉｌｅｉｎｄｕｓｔｒｙａｎｄｏｔｈｅｒｅｎｇｉｎｅｅｒｉｎｇａｐｐｌｉｃａｔｉｏｎｓ.Ｄｕｒｉｎｇｔｈｅｏｐｅｒａｔｉｏｎａｌｌｉｆｅ ,ｔｈｅｖａｒｉａｎｃｅｏｆｔｅｍｐｅｒａｔｕｒｅａｎｄｍｏｉｓｔｕｒｅｒｅｄｕｃｅｓｔｈｅｅｌａｓｔｉｃｍｏｄｕｌｉ…     

On the Buckling of Axially Compressed Thin Cylindrical Shells

ABSTRACT

A simple general method for the evaluation of the effect of shape imperfections on the buckling of thin shells is briefly presented. This method is applied to the axially compressed thin cylindrical shell resulting in an efficient numerical procedure for the computation of its buckling strength. The procedure is applicable to any sufficiently smooth imperfection pattern and has given results in good agreement with the available experimental data.     

Determining Critical Stresses for Axially Compressed Cylindrical Shells from an Analysis of Response Characteristics

The stability of metallic and glass-reinforced plastic cylindrical shells is analyzed experimentally. It is established that if the equivalent stiffness is taken as an argument of the formula used to evaluate critical stresses in designing a shell, then the critical stresses depend linearly on its stiffness     

正交各向异性旋转壳的塑性拉伸失稳

研究了正交各向异性旋转壳的拉伸塑性失稳，给出了失稳条件下强化材料旋转壳的应力和应变。     

Elastoplastic Deformation of Flexible Cylindrical Shells With Two Circular Holes under Axial Tension

The elastoplastic state of thin cylindrical shells with two circular holes under axial tension is analyzed considering finite deflections. The distributions of stresses along the contours of the holes and in the zone of their concentration are studied by solving doubly nonlinear boundary-value problems. The solution obtained is compared with the solutions that account for either physical nonlinearity (plastic deformations) and geometrical nonlinearity (finite deflections) alone and with a numerical solution of the linearly elastic problem. The stress-strain state near the two holes is analyzed depending on the distance between the holes and the nonlinear factors accounted for__________Translated from Prikladnaya Mekhanika, Vol. 41, No. 5, pp. 52–57, May 2005.     

Stability of Axially Compressed Noncircular Cylindrical Shells Consisting of Panels of Constant Curvature

The stability problem is solved for an axially compressed cylindrical shell. Its cross section is formed by circular arcs of radius r with ends supported on a closed circle of radius R. The solution is based on the Flügge equations of the classic theory of deep cylindrical shells. It is shown that the critical axial load for shells of medium length and appropriately chosen cross-sectional profile can be increased by a factor of R/r approximately, compared with the circular shell. The shells length affects considerably the efficiency of noncircular shells of this type. This design model allows us to find out how the local properties of the shell and its stiffness are related     

The Subharmonic Bifurcation of a Viscoelastic Circular Cylindrical Shell

In this paper the nonlinear dynamic behavior of a viscoelastic circular cylindrical shell under a harmonic excitation applied at both ends is studied. The modified Flugge partial differential equations of motion are reduced to a system of finite degrees of freedom using the Galerkin method. The equations are solved by the Liapunov–Schmidt reduction procedure. In order to study 1/2 and 1/4 subharmonic parametric resonance of the shell, the transition sets in parameter plane and bifurcation diagrams are plotted for a number of situations. Results indicate that, for certain static loads, the shell may display jumps due to the presence of dynamic periodic load with small amplitude. Additionally, different physical situations are identified in which periodic oscillating phenomena can be observed, and where 1/4 subharmonic parametric resonance is simpler than the 1/2-one.     

轴向运动层合圆柱壳体的振动特性

研究了轴向运动层合圆柱壳体的振动特性．基于Donnell壳体理论,建立了轴向运动层合圆柱壳体的横向振动方程,使用Galerkin方法求解该振动方程,得到其固有频率,通过与有限元结果对比说明方法的有效性．分析了轴向速度、纤维方向角、长径比和厚径比对壳体振动特性的影响．研究表明：当纤维方向角为 (15?/-15?)s时,轴向运动柱壳前3阶固有频率达到最大值．     

层叠式PVDF压电作动器及圆柱壳的振动主动控制

设计了一个层叠式PVDF压电作动器用于壳结构的振动控制。考虑压电层、粘接层、壳体耦合关系,推导了表面局部粘贴层叠式PVDF压电作动器的圆柱壳的振动控制方程,给出了作动力与压电层和粘接层层数、厚度之间的关系以及作动力与作动器粘贴位置之间的关系。针对一端固定、另一端自由的圆柱壳,进行了振动控制仿真。结果表明层叠式PVDF压电作动器作动力与作动器层数近似成线性关系,增大作动器层数能有效增大作动力,在低控制电压下能显著抑制圆柱壳振动,作动器周向不完全粘贴时,在径向产生的径向作动力对壳体横向振动控制非常有利。说明了层叠式PVDF压电作动器是一种可用于壳体结构振动并具有良好作动效果的作动器。