Glass-forming ability of butanediol isomers

In this study, the thermal behavior of butanediol isomers is investigated for temperatures ranging from 103 to 303 K using differential scanning calorimetry, complemented, when necessary, by polarized light thermal microscopy. The butanediol isomers display quite different thermal behaviors: for 1,2- and 1,3-isomers, glass transition is the only thermal event observed; for 1,4-butanediol, crystallization occurs on cooling even at a high scanning rate and no glass formation was detected; and for the 2,3-isomer, glass or crystal formation is dependent on the experimental conditions employed. The glass-forming ability of the isomers is correlated with data available on their molecular symmetry.     

Thermal analysis of protein–metallic ion systems

Advanced thermal analysis methods, such as temperature modulated DSC (differential scanning calorimetry) and quasi-isothermal TMDSC were used to analyze the protein–metallic ion interactions in silk fibroin proteins. The precise heat capacities were measured and theoretically predicted in this study. To remove bound water and simplify the system, a thermal cycling treatment through both standard DSC and TMDSC was used to detect the underlying heat capacity and reveal the phase transitions of the silk–metallic salts system. Results show that K⁺ metallic salts play the role of plasticizer in silk fibroin proteins, which reduces the glass transition (T_g) of the pure silk protein and negatively affects its structural thermal stability. On the other hand, Ca²⁺ metallic salts act as an anti-plasticizer, and increase the glass transition and the thermal stability of the silk protein structure. This indicates that the thermal analysis methods offer a new pathway to study protein–metallic ion systems, yielding very fruitful information for the study of protein structures in the future.     

Broadened glass transition in a liquid-crystalline polymer studied by thermally stimulated currents,AC dielectric,dynamic mechanical,and DSC methods

Thermally stimulated currents (TSC), a. c. dielectric, dynamic mechanical (DMTA), and differential scanning calorimetry (DSC) methods were used to study the glass transition in a thermotropic liquid-crystalline copolyester. All the techniques were consistent in the determination of the main glass transition temperature. Using the high sensitivity of the TSC thermal sampling method, it was shown that cooperative glass transition-like relax-ations occur down to 100°C below the main glass transition. DSC was sensitive only to a broadening of the glass transition to about ca. 30°C, so it was concluded that the thermal sampling method is sensing a very small fraction of cooperatively relaxing species which cannot be detected by DSC. Ac dielectric measurements and DMTA also indicated that the glass transition was broad, but difficulties with overlapping transitions prevented quantitative determination of the breadth of the glass transition. The results suggest that the broad glass transition, in this mostly amorphous LCP, is due to chemical heterogeneity of the copolyester chain. Other evidence indicates that the broadening is not due to the oriented nature of the glassy state. Some discussion is presented concerning how the heterogeneous nature of the LCP glass leads to compensation of the Arrhenius curves obtained by the thermal sampling method. © 1993 John Wiley & Sons, Inc.     

The effect of different hardeners on the ageing of crosslinked epoxy resins

Polymers based on epoxies are widely used in the industrial production of materials for different applications. The crosslinking is often done with hardeners like aliphatic or aromatic amines, with dicarboxylic acid anhydride or anionically. The resins containing mineral fillers possess similar thermal mechanical properties. On thermal oxidative ageing, however, the systems behave very differently. An account is given of the thermal mechanical behaviour and of the weight loss on ageing above the glass transition temperature. By using semiempirical molecular orbital calculations we have been able to identify a possible reason for the different thermal oxidative stability of epoxy resins crosslinked with different hardeners.     

Inducing bioactivity in dental porcelain through bioglass®

Dental materials restore morphology and function of lost or destroyed teeth, but cannot completely rebuild the structural relationship with soft periodontal tissues. The induction of bioactivity on classic dental porcelain can be achieved through the addition of bioactive glass. The aim of this study was to investigate the effect of Bioglass^® on the thermal properties of dental porcelain in order to correlate the proportions of mixtures with the changes in thermal properties. Differential thermal analysis was performed in order to determine the characteristic temperatures of the mixtures. The increase of bioactive glass concentration in mixtures induces a shift to lower temperatures of the melting point temperature. This observation is attributed to the substitution of silicon ions by aluminium ions and to the formation of Al–O bond, which is weaker than Si–O bond. Mixtures heated at 950°C were examined also by the transmission electron microscopy (TEM) in order to be studied the microstructure of these samples at this critical temperature. The observed microstructural changes, confirm the process of substitution of Si ⁴⁺ ions by Al ³⁺ ions.     

Study of the crystallization of leucite in feldspar glass matrix

Feldspathic glass–ceramics reinforced with leucite are usually used in dental prosthesis. This study focused on leucite crystallization kinetics due to its importance to the end product of a dental crown processing. Leucite grains were nucleated and grown from feldspathic glass frit powders with particle size smaller than 45 μm. The nucleation and crystallization kinetics of leucite crystals in the glass matrix was investigated under isothermal and non-isothermal conditions through differential thermal analysis. The samples were also characterized by X-ray diffraction and scanning electron microscopy. The temperature of maximum nucleation rate was determined from the DTA curves of samples heat treated at different temperatures. The activation energy (E) of leucite crystallization was determined by the Kissinger method and the Avrami parameter (n) indicated that surface crystallization is the dominant mechanism in the glass.     

Thermal characterization of benzylcellulose derivatives prepared from bleached pinus kraft pulp

The thermal characterization (DSC and TG) of benzylcellulose derivatives prepared from the benzylation of bleached Pinus Kraft pulp is described in this paper. The objective of this study was to examine the changes in glass transition temperature (T _g) and the thermal stability of the benzylated product as a function of the benzylation extent (degree of substitution). The DSC analysis showed that the benzylcelluloses can display glass transition temperature at two different regions and that thermal stability is slightly higher than that of the parent cellulose. This revised version was published online in August 2006 with corrections to the Cover Date.     

Analysis of Composites with Infrared Thermography

The aim of this study was a non-destructive evaluation of composites through their behaviour under thermal stimulation. Such behaviour was monitored by infrared thermography. Several specimens were fabricated involving: glass/epoxy with inclusion of foreign materials; carbon/epoxy with backdrilled holes; carbon/epoxy with impact damage; Glare^® failed in bearing way. The obtained results prove that infrared thermography is capable of detecting the materials inhomogeneities and/or damage listed above. In particular, lock-in thermography is capable of supplying useful information about: the distribution of the adhesive thickness in composite structures; the distribution of the paint thickness; the behaviour under load of aluminium layers and glass fibres in Glare^®.     

Electrospun nanofibrous membranes embedded with aerogel for advanced thermal and transport properties

The primary purpose of cold weather clothing is to shield the wearer from the extremities of the external environment. The thermal properties of nanofibers and their potential applications have tremendous scope and application in this area. The objective of this study was to investigate the mechanisms of heat transfer through fibrous insulation where the fiber diameter was less than 1 μm. Electrospinning process was used to produce flexible polyurethane and polyvinylidene fluoride nanofibers embedded with silica aerogel. The thermal and transport behavior of the samples was evaluated, and results were statistically analyzed. Presence of aerogel particles were confirmed through microscopic examination. Thermal behavior was investigated by using thermogravimetric analysis and differential scanning calorimetry. The results showed that the polyvinylidene fluoride nanofibrous membranes embedded with aerogel obtained a good thermal stability with lower weight loss than polyurethane nanofibrous membranes. The glass transition and melting point was not affected by the aerogel content in the layers, validating that polymers are not miscible. The increase in duration of electrospinning led to higher web thickness, which resulted in considerable decrease in air permeability. Considerable improvement of thermal insulation was observed by increasing the number and the weight per unit area of both nanofibrous membranes. The results confirmed increase in thermal insulation by embedding silica aerogel in nanofibrous membranes. With reference to the results, it could be concluded that nanofibers embedded with aerogel are good for thermal insulation in cold weather conditions. Thermal insulation battings incorporating nanofibers could possibly decrease the weight and bulk of current thermal protective clothing.     

石墨烯玻璃透明薄膜加热特性

Graphene has become a research focus in recent years owing to its excellent characteristics, and glass is a commonly used material with high transparency and low cost. Graphene glass combines the excellent properties of both graphene and glass; graphene glass has not only high thermal conductivity, high electrical conductivity, and good surface hydrophobicity but also exhibits superior electrothermal conversion and wide-spectrum high-light-transmittance characteristics. Therefore, the study of graphene glass films is of theoretical value and practical significance. In this study, a high-purity glass-based (JGS1 quartz glass) multilayer graphene film was developed based on an atmospheric-pressure chemical vapor deposition (APCVD) method, and its electrical characteristics, light transmittance, and electrical heating characteristics were experimentally investigated in detail. The results show that graphene glass with different surface resistance values obtained through direct growth on a high-purity quartz glass substrate using the APCVD method, not only has excellent uniformity and quality, but also has considerably flat and high transmittance across the entire visible light region and exhibits excellent heating performance and fast response time. For graphene glass with a surface resistance of 1500 Ω·sq^-1, the light transmittance can reach 74%, and the saturation temperature can rise to 185 ℃ by applying a bias voltage of 40 V. In addition, when the resistance value of the graphene glass is 420 Ω·sq^-1, the graphene glass reaches a high saturation temperature of 325 ℃ in 40 s, and the corresponding heating rate can exceed 18 ℃·s^-1, achieving a significantly higher heating rate than other heating films at the same voltage. Compared with the polyethylene-terephthalate- (PET-) based and silicon-based graphene films obtained by the transfer, graphene glass has a higher saturation temperature, shorter thermal response time, and faster heating rate. Furthermore, graphene glass exhibits better heating cycle stability and longer-term heating stability at a constant voltage. In addition, an experiment using the graphene glass to thermally tune the wavelength of a vertical-cavity surface-emitting laser was conducted and gave good results. The position of the laser peak controlled by the graphene glass was red-shifted by 1.78 nm by applying a voltage of 20 V, and the wavelength tuning efficiency reached 0.059 nm·℃^-1. Compared with PET-based and silicon-based graphene films, the actual electrical heating capacity of graphene glass increased by 195%. These experimental findings demonstrate that graphene glass transparent films with excellent electric heating characteristics can be used in various transparent electric heating fields and have relatively wide application prospects.     

Solvent-free esterification of poly（vinyl alcohol） and maleic anhydride through mechanochemical reaction

A solid-state mechanochemical processing,that is,pan-milling,was used to conduct the esterification of poly(vinyl alcohol) (PVA) with maleic anhydride (MA) through stress-induced reaction.FTIR spectrum study indicated the presence of ester linkages and olefinic double bonds in maleic anhydride cross-linked PVA.Thermal properties of the cross-linked product were characterized by DSC.The results showed its glass transition temperature was 20℃higher than the original linear PVA and the thermal stability was also improved.     

PMMA-ZrO2等有机无机杂化材料的制备与表征

以烯丙基乙酰丙酮作为偶闻剂应秀溶胶凝胶法制备了一系列均匀透明的ＰＭＭＡ－ＺｒＯ２等有机无机杂化材料，利用ＵＶ，ＩＲ对其制备过程进行了研究，并测定了所得杂化玻璃的ＴＧＡ性质。     

Thermal characterization of mica–epoxy composite used as insulation material for high voltage machines

The study of mica–epoxy-based composite has a great role in high voltage machines industry. Beside electric properties, this composite should present compatible mechanical and chemical, in this case thermal characteristics to insulate properly the conductor strand, avoiding short-circuits, and leading electrical current with minimal losses. Improvement of the quality is possible through the knowledge of raw materials and system. This study aims to list a complete thermal characterization of mica composite, its components, epoxy resin, anhydride methylhexahydrophtalic, mica tape and zinc naphthenate, and thermoanalytical interactions between them. These data shows intrinsic properties of the system, which is so relevant to its great electrical and thermal performance. Thermal analysis allows the detailed study of curing process and thermal decomposition, predicting and suggesting mechanisms, beside future and possible optimization to the system. Composite system glass transition (T _g) was obtained through an important and very respected methodology, presenting the value of T _g = 138 ± 2 °C, finally characterizing the material.     

Thermal behavior of blends based on a thermoplastic-modified epoxy resin with a crosslinking density variation

The thermal behavior of blends based on a polystyrene (PS) and several epoxy-amine systems where amino groups were provided by a monoamine (MA) and a diamine (DA) mixed in different proportions was investigated. This way, the crosslinking density of epoxy-amine polymer was controlled and continuously changed from a linear polymer (epoxy-MA) to a highly crosslinked polymer (epoxy-DA). The effect of the MA–DA proportion and PS modifier on the thermal stability, glass transition, and polymerization reaction was studied by differential scanning calorimetry and thermogravimetric analysis. The MA–DA ratio and modifier proportion did not affect the reaction heat but affected the reactivity. The thermal stability and glass transition temperature increased by increasing the DA proportion in the blend as a result of the higher degree of crosslinking. A study of miscibility of blends based on glass transitions was performed. The thermoplastic-modified materials generally showed two glass transitions with values close to the those of the pure materials, indicating that the mixtures were separated into phases.     

Effect of Supermolecular Structure Changes on the Glass Transition of Polymer

The idea of two miscellaneous amorphous fractions in one polymeric system is under consideration. A new factor influencing the glass transition and a relaxation observed in polymers exhibiting different supermolecular structures is discussed. In order to clarify the specific arrangement of backbone chains two types of polymers were taken under investigation: semicrystalline poly(4-methyl-1-pentene) and a liquid-crystalline poly(norbornene) derivative. In both cases,it was possible to find two well separated glass transitions. Differential scanning calorimetry and dynamic mechanical thermal analysis were used to study the effect of thermal history on the assignment of the glass transition event associated with two miscellaneous amorphous phases. The problem of molecular arrangement in the amorphous phases is discussed. This revised version was published online in July 2006 with corrections to the Cover Date.     

激活CaO-MgO-SiO_2长余辉玻璃发光性质

报道了一种新型的Eu~(2+)离子激活硅酸盐玻璃,该玻璃组成为2CaO-MgO-3SiO_2-0.015Eu_2O_3(CMSE)。通过透射光谱、稳态荧光光谱、余辉光谱和热释光等技术手段对CMSE的发光性质进行了深入研究。研究发现CMSE可以被紫光和近紫外光激发,获得黄色长余辉发光。热释光曲线的分析表明,CMSE的长余辉性质主要来自于玻璃基质中陷阱深度为0.83 e V左右的定域能级。研究认为对CMSE发光性质的研究有利于开发新型稀土离子激活近紫外激发LED用硅酸盐玻璃发光材料。     

Synthesis and Characterization of Indium-borate Glass-ceramics Containing Ho0.01Ce0.74Zr0.25O1.995 Nanorods via Incorporation Method

Glasses in the system 5In₂O₃·94Na₂B₄O₇ were fabricated via melt quenching technique. The amorphous nature of the quenched glasses was confirmed by X‐ray powder diffraction studies, and the infrared spectra of the glasses show no boroxol ring formation in the structure of these glasses. Differential thermal analysis is shown glass transition temperature 696°C and crystallization temperature 1151°C. A cerium‐zirconium mixed oxide Ce_0.75Zr_0.25O₂ and Ho‐doped cerium‐zirconium mixed oxide were obtained by solid‐state method. Then glass powder and Ho‐doped cerium‐zirconium mixed oxide were mixed. The mixture was heated in a crucible. The glass‐ceramic sample was obtained by pouring the melts on stainless steel. Obtained samples were annealed at 450°C for 1 h to remove thermal strain. Differential thermal analysis for glass‐ceramic sample is shown glass transition temperature 668°C and crystallization temperature 1159°C. The scanning electron microscopy study for glass‐ceramic indicates that the crystallized glass consists of rod‐like crystals with average diameter of about 38 nm dispersed in the glassy regions.     

Adsorption of Th4+ from aqueous solution onto Poly(N,N-diethylacrylamide-co-acrylic acid) microgels

Preparing glass to be used as a radioactive waste immobilizer from municipal waste is the aim of this paper. Up to 90 wt% of municipal waste was obtained by burning the raw waste at 700 °C for 5 h; this were successfully vitrified into borosilicate and sodium borate glasses at ~1,200 °C. The long term behavior of such glass is one of the most important factors, which is determined by their durability in aqueous solution. Experimental durability data of the prepared glass immersed in ground water together with γ-irradiation was found to be affected according to the different irradiation doses. In addition, thermal analysis and glass surface morphology were investigated. The evolution of the damage on the studied properties was correlated to the changes in the glass network depending on their composition and irradiation dose. The results showed that glass matrix containing higher amount of municipal waste possess high durability and low thermal expansion after being gamma irradiated. The results showed that glass containing higher amount of municipal waste possess high durability and low thermal expansion after irradiation.     

聚合物电致发光二极管热特性研究

采用ANSYS有限元分析软件中热分析结构单元,对聚合物电致发光二极管(PLED)在光强为1000cd/m2时的热特性进行模拟,获得其温度场、热流分布及温度梯度的分布图,从仿真结果知PLED器件的最高温度为45.968℃,处于PFO-BT发光层,最低温度为45.95℃,处于石英玻璃基底末端.计算得出聚合物发光器件总热阻为1305℃/W,聚合物发光层至石英玻璃基底末端热阻为1℃/W.通过改变PLED器件输入功率、基底材料以及基底厚度3个参数,分别模拟得出其对PLED器件热特性的影响,仿真结果表明器件最高温度TH与输入功率P显现良好的线性关系;不同基底材料对器件温度影响小,负极端为器件主要散热通径;当基底厚度不断增加时,PLED器件最高温度随着增加,而最低温度不断减少,器件总热阻基本不变,发光层至石英基底末端热阻线性增大.