On the spray-drying deposition of TiO2 photocatalytic films

The photocatalytic activity of TiO₂ films deposited on different substrates by the spray-drying method using suspensions of commercially available TiO₂ (Degussa P25 or Tronox) as starting material was studied. The influence of the type of the initial TiO₂, preparation conditions (temperature of the substrate during the film deposition, temperature of the post-deposition annealing), substrate material (glass, fused silica, stainless steel and graphite), the presence of additives in the spraying suspension (polyethylene glycol, ethylene glycol and acetylacetone) and its sonication before spraying on the morphology, size of crystallites and phase composition (rutile/anatase ratio) was studied. Optimal conditions for spray deposition of the films are suggested.     

Preparation and characterization of thermally evaporated titanium phthalocyanine dichloride thin films

Titanium phthalocyanine dichloride (TiPcCl₂) thin films are prepared on glass substrates by vacuum-sublimation technique. The optical constants of thin films are obtained by means of thin film spectrophotometry. Planar structures for the study of electrical properties are fabricated with TiPcCl₂ as active layer and silver as the contact electrodes. The effects of post-deposition annealing on the optical band gap have been studied. The optical transition is found to be direct allowed in nature. The invariance in the optical band gap shows the thermal stability of the material. The activation energies are determined using the Arrhenius plots between electrical conductivity and inverse temperature. The variation in activation energy with post-deposition annealing is investigated. The unit cell dimensions of TiPcCl₂ thin films are also determined by indexing the powder diffraction data. The variations of the surface morphology and grain size with annealing have also been studied.     

Influence of substrate temperature and post-treatment on the properties of ZnO:Al thin films prepared by pulsed laser deposition

Highly transparent conductive Al₂O₃ doped zinc oxide (AZO) thin films have been deposited on the glass substrate by pulsed laser deposition technique. The effects of substrate temperature and post-deposition annealing treatment on structural, electrical and optical properties of AZO thin films were investigated. The experimental results show that the electrical resistivity of films deposited at 240 °C is 6.1 × 10⁻⁴ Ω cm, which can be further reduced to as low as 4.7 × 10⁻⁴ Ω cm by post-deposition annealing at 400 °C for 2 h in argon. The average transmission of AZO films in the visible range is 90%. The optical direct band gap of films was dependent on the substrate temperature and the annealing treatment in argon. The optical direct band gap value of AZO films increased with increasing annealing temperature.     

Oblique angle deposition of TiO2 thin films prepared by electron-beam evaporation

Optical, structural and photocatalytic properties of TiO₂ thin films obliquely deposited on quartz glass substrate using an electron-beam evaporation method were investigated. The photocatalytic activity of the films was evaluated by photodecomposition of methylene blue. An increase in incident deposition angle increased the porosity and surface roughness of the TiO₂ films. As a result, the photocatalytic activity was enhanced with incident deposition angle up to 60°. However, a further increase in incident deposition angle to 75° reduced the photocatalytic activity due to a lack of the crystalline phase.     

Vacancies ordered in screw form (VOSF) and layered indium selenide thin film deposition by laser back ablation

Indium selenide thin films are important due to their applications in non-volatile memory and solar cells. In this work, we present an initial study of a new application of deposition-site selective laser back ablation (LBA) for making thin films of In₂Se₃. Invacuo annealing and subsequent characterization of the films by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) indicate that control of substrate temperature during deposition and post-deposition annealing temperature is critical in determining the phase and composition of the films. The initial laser fluence and target film thickness determine the amount of material deposited onto the substrate.     

各向同性纳米结构Fe-Pt薄膜的结构和磁性

采用直流溅射和热处理技术制备了两个各向同性的纳米结构Fe-Pt永磁合金薄膜系列,并研究了它们的结构和磁性.研究表明,在富Fe双相纳米结构Fe-Pt永磁合金薄膜中,仅由硬磁的FePt相与软磁的Fe₃Pt相组成;在同一系列中,随Fe层厚度的增加,饱和磁极化强度和剩磁明显增大.由Kelly-Henkel图研究指出,在上述Fe-Pt纳米结构永磁合金薄膜中,磁相互作用主要由近邻纳米晶粒间的铁磁交换相互作用控制. 关键词： 磁性薄膜 纳米结构 矫顽力     

Studies of thin FeAlN films prepared by different techniques

The microstructure, morphology, and magnetic properties of FeAlN films deposited by reactive rf magnetron sputtering with subsequent treatment by three techniques, namely, in situ, ex situ (with the sputtering and annealing processes separated), and thermal crystallization of amorphous alloys, have been studied. FeAlN films prepared by the ex situ technique exhibit the best soft magnetic characteristics. Thermal crystallization of amorphous alloys produced films with properties having the highest thermal stability. Films 800-to 1000-nm thick were found to have the best soft magnetic properties. The dependences of the properties of FeAlN films on nitrogen content and annealing temperature were established. The conditions favoring the preparation of thin nanostructured FeAlN films featuring the best soft magnetic characteristics (saturation induction B _S = 1.8 T, coercivity H _C = 1.2 Oe, magnetic susceptibility μ₁ (1 MHz) = 3400) were determined.     

Influences of CO2 laser annealing on mechanical and laser-induced damage properties of ZrO2 thin films

Zirconium dioxide (ZrO₂) thin films were deposited on BK7 glass substrates by the electron beam evaporation method. A continuous wave CO₂ laser was used to anneal the ZrO₂ thin films to investigate whether beneficial changes could be produced. After annealing at different laser scanning speeds by CO₂ laser, weak absorption of the coatings was measured by the surface thermal lensing (STL) technique, and then laser-induced damage threshold (LIDT) was also determined. It was found that the weak absorption decreased first, while the laser scanning speed is below some value, then increased. The LIDT of the ZrO₂ coatings decreased greatly when the laser scanning speeds were below some value. A Nomarski microscope was employed to map the damage morphology, and it was found that the damage behavior was defect-initiated both for annealed and as-deposited samples. The influences of post-deposition CO₂ laser annealing on the structural and mechanical properties of the films have also been investigated by X-ray diffraction and ZYGO interferometer. It was found that the microstructure of the ZrO₂ films did not change. The residual stress in ZrO₂ films showed a tendency from tensile to compressive after CO₂ laser annealing, and the variation quantity of the residual stress increased with decreasing laser scanning speed. The residual stress may be mitigated to some extent at proper treatment parameters.     

Fabrication and vacuum annealing of transparent conductive Ga-doped Zn0.9Mg0.1O thin films prepared by pulsed laser deposition technique

In this study, highly transparent conductive Ga-doped Zn_0.9Mg_0.1O (ZMO:Ga) thin films have been deposited on glass substrates by pulsed laser deposition (PLD) technique. The effects of substrate temperature and post-deposition vacuum annealing on structural, electrical and optical properties of ZMO:Ga thin films were investigated. The properties of the films have been characterized through Hall effect, double beam spectrophotometer and X-ray diffraction. The experimental results show that the electrical resistivity of film deposited at 200 °C is 8.12 × 10⁻⁴ Ω cm, and can be further decreased to 4.74 × 10⁻⁴ Ω cm with post-deposition annealing at 400 °C for 2 h under 3 × 10⁻³ Pa. In the meantime, its band gap energy can be increased to 3.90 eV from 3.83 eV. The annealing process leads to improvement of (0 0 2) orientation, wider band gap, increased carrier concentration and blue-shift of absorption edge in the transmission spectra of ZMO:Ga thin films.     

Amorphous to crystalline phase transition in pulsed laser deposited silicon carbide

SiC thin films were grown on Si (1 0 0) substrates by excimer laser ablation of a SiC target in vacuum. The effect of deposition temperature (up to 950 °C), post-deposition annealing and laser energy on the nanostructure, bonding and crystalline properties of the films was studied, in order to elucidate their transition from an amorphous to a crystalline phase. Infra-red spectroscopy shows that growth at temperatures greater than 600 °C produces layers with increasingly uniform environment of the Si-C bonds, while the appearance of large crystallites is detected, by X-ray diffraction, at 800 °C. Electron paramagnetic resonance confirms the presence of clustered paramagnetic centers within the sp² carbon domains. Increasing deposition temperature leads to a decrease of the spin density and to a temperature-dependent component of the EPR linewidth induced by spin hopping. For films grown below 650 °C, post-deposition annealing at 1100 °C reduces the spin density as a result of a more uniform Si-C nanostructure, though large scale crystallization is not observed. For greater deposition temperatures, annealing leads to little changes in the bonding properties, but suppresses the temperature dependent component of the EPR linewidth. These findings are explained by a relaxation of the stress in the layers, through the annealing of the bond angle disorder that inhibits spin hopping processes.     

Photocatalytic properties of TiO2 thin films obtained by glancing angle deposition

Titanium dioxide (TiO₂) thin films with different nanostructures such as nano-particles and separated vertical columns were grown by glancing angle deposition (GLAD) in an electron beam evaporation system. The photocatalytic properties of grown TiO₂ films with different deposition angles and different annealing temperatures were evaluated by following decomposition of methyl orange under ultraviolet (UV) light irradiation. The results suggest that increased surface area due to the GLAD process could improve the photocatalytic properties of TiO₂ films.     

Magnetoelectrical properties of W doped ZnO thin films

ZnO thin films were deposited on the Si(100) substrate by rf sputtering using a 99.999% pure commercially bought and a home made target under 100 W power. The home made ZnO target, including 1–2% tungsten, was synthesized via solid state reaction. Thin films were deposited under a flow of 70% argon and 30% O₂ gas mixture followed by post-deposition annealing under 1 Torr oxygen atmosphere. Both deposition and post-deposition annealing were done at 420±1 °C. The structural analyses show that the films were in the [0002] preferred direction and that W atoms are bound to the oxygen atoms by replacing the Zn host atoms. Although no specific change was observed in the magnetic properties as a result of W doping, significant changes in the electrical properties were observed, as determined by the longitudinal and transversal magneto-electrical measurements. It was found that the W impurities induce better insulating properties due to lower carrier concentration and higher resistivity values. On the other hand, the enhanced positive magnetoresistivity and the existence of polarized spin currents, which were not specific for pure ZnO thin films, were observed in W doped ZnO films below 10 K.     

A comparative study of the physical properties of Sb2S3 thin films treated with N2 AC plasma and thermal annealing in N2

As-deposited antimony sulfide thin films prepared by chemical bath deposition were treated with nitrogen AC plasma and thermal annealing in nitrogen atmosphere. The as-deposited, plasma treated, and thermally annealed antimony sulfide thin films have been characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy, scanning electron microscopy, atomic force microscopy, UV-vis spectroscopy, and electrical measurements. The results have shown that post-deposition treatments modify the crystalline structure, the morphology, and the optoelectronic properties of Sb₂S₃ thin films. X-ray diffraction studies showed that the crystallinity of the films was improved in both cases. Atomic force microscopy studies showed that the change in the film morphology depends on the post-deposition treatment used. Optical emission spectroscopy (OES) analysis revealed the plasma etching on the surface of the film, this fact was corroborated by the energy dispersive X-ray spectroscopy analysis. The optical band gap of the films (E_g) decreased after post-deposition treatments (from 2.36 to 1.75 eV) due to the improvement in the grain sizes. The electrical resistivity of the Sb₂S₃ thin films decreased from 10⁸ to 10⁶ Ω-cm after plasma treatments.     

Morphology and photocatalysis of mesoporous titania thin films annealed in different atmosphere for degradation of methyl orange

The effect of different annealing atmosphere on the morphology and photocatalytic activity of mesoporous TiO₂ thin films by dip-coating technique is investigated. The annealing temperature and atmosphere causes significant change of the morphology, thermal stability, photoluminescence, and photocatalytic properties of mesoporous TiO₂ films. As-prepared mesoporous thin films have an amorphous structure that is transformed to crystalline TiO₂ with well-maintained mesoporous structure at 450°C in various annealing atmosphere except that the mesoporous structure is fully destroyed for films annealed in air. Films annealed in N₂ show the enhanced UV photodegradation of methyl orange (MO) resulting from the enhanced crystallinity in these films evidenced by XRD and Raman spectra. These findings can be used to tailor the structure and morphology of mesoporous TiO₂ films and thus improve their photocatalytic activity for efficient removal of dye effluents in wastewater.     

High-rate reactive magnetron sputtering of zirconia films for laser optics applications

ZrO₂ exhibits low optical absorption in the near-UV range and is one of the highest laser-induced damage threshold (LIDT) materials; it is, therefore, very attractive for laser optics applications. This paper reports explorations of reactive sputtering technology for deposition of ZrO₂ films with low extinction coefficient k values in the UV spectrum region at low substrate temperature. A high deposition rate (64 % of the pure metal rate) process is obtained by employing active feedback reactive gas control which creates a stable and repeatable deposition processes in the transition region. Substrate heating at 200 °C was found to have no significant effect on the optical ZrO₂ film properties. The addition of nitrogen to a closed-loop controlled process was found to have mostly negative effects in terms of deposition rate and optical properties. Open-loop O₂ gas-regulated ZrO₂ film deposition is slow and requires elevated (200 °C) substrate temperature or post-deposition annealing to reduce absorption losses. Refractive indices of the films were distributed in the range n = 2.05–2.20 at 1,000 nm and extinction coefficients were in the range k = 0.6 × 10^?4 and 4.8 × 10^?3 at 350 nm. X-ray diffraction analysis showed crystalline ZrO₂ films consisted of monoclinic + tetragonal phases when produced in Ar/O₂ atmosphere and monoclinic + rhombohedral or a single rhombohedral phase when produced in Ar/O₂ + N₂. Optical and physical properties of the ZrO₂ layers produced in this study are suitable for high-power laser applications in the near-UV range.     

Layer structure variations of ultra-thin HfO2 films induced by post-deposition annealing

To meet challenges for a smaller transistor feature size, ultra-thin HfO₂ high-k dielectric has been used to replace SiO₂ for the gate dielectric. In order to accurately analyze the ultra-thin HfO₂ films by grazing incidence X-ray reflectivity (GIXRR), an appropriate material model with a proper layer structure is required. However, the accurate model is difficult to obtain, since the interfaces between layers of the ultra-thin HfO₂ films are not easily identified, especially when post-deposition annealing process is applied. In this paper, 3.0 nm HfO₂ films were prepared by atomic layer deposition on p-type silicon wafer, and annealed in Ar environment with temperatures up to 1000 °C. The layer structures and the role of the interfacial layer of the films in the post-deposition annealing processes were evaluated by X-ray diffraction and X-ray photoelectron spectroscopy (XPS). The experimental results and analysis showed that layer thicknesses, crystal phases and chemical structures of the ultra-thin HfO₂ films were significantly dependent on annealing temperatures. The binding energy shifts of Hf 4f, O 1s, and Si 2p elements revealed the formation of Hf silicate (Hf-O-Si bonding) with increasing annealing temperatures. Due to the silicate formation and increasing silicon oxide formation, the interface broadening is highly expected. The structure analysis of the GIXRR spectra using the modified material structure model from the XPS analysis confirmed the interfacial broadening induced by the post-deposition annealing.     

The importance of the majority carrier polarity and p-n junction in titanium dioxide films to their photoactivity and photocatalytic properties

In this paper, undoped polycrystalline titanium dioxide films have been deposited by atomic layer deposition (ALD) using the titanium tetrachloride–water process. These films have been anatase, rutile, or mainly anatase with a varying content of rutile depending on the deposition conditions. The polarity of the majority carriers on the films has been measured with the hot-probe test and, over the range of deposition temperatures used, the anatase or anatase-dominant films have been found to be p-type whereas the rutile films have been n-type. X-ray diffraction (XRD), contact angle measurements, and methylene blue degradation tests were performed to investigate the crystallinity, photoactivity, and photocatalytic properties. All the p-type films showed good photoactivity as determined by their water contact angle while the best photocatalytic activity was shown with anatase films containing a small proportion of rutile. An explanation for the superior photoactivity of anatase due to its p-type polarity is given and the high photocatalytic property for anatase-dominant films is ascribed to the existence of p-n junctions leading to carrier separation.     

In situ grown epitaxial YBa2Cu3O7 − x thin films by pulsed laser deposition under reduced oxygen pressure during cool-down time

We report novel pulsed laser deposition conditions that were used to obtain superconducting epitaxial YBCO thin films, grown in situ using an oxygen pressure lower than the usual one during the cool-down time. We studied the influence of the PLD conditions as substrate temperature, oxygen pressure, laser fluence, and number of laser pulses on the crystallographic and morphological features, and on the superconducting properties of the films. Good superconducting properties were obtained without a high temperature post-deposition annealing process. A maximum critical temperature of 88.6 K was obtained.     

Effect of thermal annealing on the formation of silicon nanoclusters in SiOX films grown by PLD

Silicon nanoclusters formation in pulsed laser deposited (PLD) silicon suboxide (SiO_X) films by thermal annealing is reported. The SiO_X films are prepared by ablation of silicon target at different oxygen partial pressures. The different deposition conditions are employed to study the effect of oxygen concentration on the size of the nanoclusters. Post deposition thermal annealing of the films leads to the phase separation in silicon suboxide films. Fourier transform infrared spectroscopy, micro-Raman spectroscopy and UV-vis absorption spectroscopy studies were carried out to characterize the formation of silicon nanoclusters in SiO_X films.     

Annealing effects on microstructural and optical properties of Nanostructured-TiO2 thin films prepared by sol-gel technique

In this paper we report on the effect of annealing on the microsctructural and optoelectronic properties of titanium dioxide (TiO₂) thin films prepared using sol-gel method onto silicon (Si) (100) and quartz substrates. The annealing temperatures range from 200 to 1000 °C. The Microstructural properties of annealed thin films were investigated by Thermal gravimetric analyses (TGA), X-ray diffraction (XRD) and Raman Spectroscopy. The surface morphology of the film was examined using Atomic Force Microscopy (AFM) method. The optical properties of TiO₂ thin films were characterized using UV-VIS and Spectroscopic ellipsometry. The results have shown that the TiO₂ thin films persist in the anatase phase even after annealing at 800 °C. The phase transformation from anatase to rutile occurred only when the films were annealed at 1000 °C. AFM studies revealed nanocrystalline structure where their shape and density depend strongly on the annealing temperatures. The elaborated nanostructured-TiO₂ thin films present a high transparency in the visible range. Spectroscopic ellipsometry (SE) study was used to determine the effect of annealing temperature on the thickness and on the optical constant of TiO₂ thin films. Spectroscopic ellipsometry and UV-VIS shows that the band gap of TiO₂ thin films was found to decrease when the annealing temperature increases. The Anatase phase was find to show higher photocatalytic activity than the rutile one.