阻抑高碘酸钠氧化依莱铬红B褪色光度法测定痕量Sn(Ⅱ)

在加热和 NH3 - NH4Cl(p H=9.2 5 )缓冲溶液介质中 ,痕量 Sn( )能抑制高碘酸钠氧化依莱铬红 B褪色反应 ,据此建立了测定痕量 Sn( )的动力学光度分析新方法。该方法在锡的浓度为 0 .5— 9.0μg/ 2 5 m L范围内有良好的线性关系 ,方法的检出限为 2 .33× 10 -9g/ m L Sn( )。该方法用于测定天然水中痕量锡( ) ,取得满意结果     

抑制CTMAB催化结晶紫褪色光度法测定痕量铝(Ⅲ)

基于碱性介质中 ,铝 (Ⅲ )对溴化十六烷基三甲铵 (CTMAB)催化结晶紫的褪色反应有明显的抑制作用 ,建立了一种抑制 -催化褪色光度法测定痕量铝 (Ⅲ )的新方法。此法在 0 .0 2— 1.8μg/L的范围内 CAl(Ⅲ )与 ΔA值呈线性关系 ,线性回归方程为 :ΔA=0 .0 0 2 93+ 0 .2 179CAl( Ⅲ ) (μg/L) ,r=0 .9990 ,检出限为 1.4×10 -9g/m L。该法用于水样中 Al(Ⅲ )的测定 ,结果令人满意。     

阻抑高碘酸钠氧化铬天青B褪色光度法测定痕量钛

基于加热和 NH3- NH4 Cl(p H=10 .2 0 )缓冲溶液存在下 ,痕量钛 ( )能阻抑高碘酸钠氧化铬天青 B的褪色反应 ,建立了阻抑高碘酸钠氧化铬天青 B褪色光度法测定痕量钛 ( )的新方法。该方法的线性范围为 0— 4 0 .0 ng/ m L Ti( ) ,检出限为 5 .85× 10 - 1 0 g/ m L ,用于鲍鱼壳中痕量钛的测定 ,结果令人满意     

催化碘酸钾氧化VB4R-DBS离子缔合物褪色光度法测定痕量亚硝酸根

基于加热和 p H=7.5 0的条件下 ,NO-2 催化碘酸钾氧化维多利亚蓝 4 R(VB4 R) -十二烷基苯磺酸钠(DBS)离子缔合物的褪色反应 ,建立了一种测定痕量亚硝酸根的新催化光度法。 NO-2 浓度在 1.0—10 .0 μg/ L范围内服从比耳定律 ,检出限为 1.0× 10 -11g/ m L。该法用于测定水样中的 NO-2 的含量 ,结果令人满意     

中性红褪色光度法测定蒙药铜灰体系中产生的过氧化氢含量

在 p H=3.5的乙酸 -乙酸钠缓冲溶液中 ,用中性红褪色光度法测定了蒙药铜灰体系中产生的过氧化氢的含量。过氧化氢在 0— 5 0μg/ 2 5 m L范围内与 lg(A0 / A)值呈线性关系 ,线性回归方程为 lg(A0 / A) =2 .5× 10 -3+1.0 5× 10 -2 C双氧水 (μg/ 2 5 m L) ,r=0 .9999     

高碘酸钾催化光度法测定痕量铑

在磷酸和热水浴中 ,Rh( )催化高碘酸钾氧化二甲基黄褪色 ,由此建立了测定铑的新催化光度法。本方法的线性范围为 0— 4 .0 μg/ 2 5 m L,检出限为 4 .71× 10 -10 g/ m L。对 2 .0 μg/ 2 5 m L Rh( )测定的相对标准偏差为 1.4 3% (n=11) ,催化反应的表观活化能为 12 5 .8k J/ mol。此法已用于某些催化剂和冶金产品中痕量铑的测定 ,结果令人满意。     

催化动力学光度法测定禽蛋中的痕量硒(Ⅳ)

在酸性介质中及三乙醇胺存在下 ,以硒 ( )对硫化钠氧化亚甲基蓝褪色反应具有很强的催化作用为依据 ,优化了该催化反应的动力学条件 ,建立了利用动力学光度法测定硒 ( )的新方法。在 0— 5 0μg/ 5 0 m L范围内 ,硒的含量与褪色反应 ( A0 - A)呈很好的线性关系 ,检出限为 3.74× 10 -7g/ L。该方法具有良好的选择性和准确度 ,用于禽蛋中痕量硒 ( )的测定 ,结果令人满意     

催化过硫酸钾氧化银-邻二氮菲-荧光黄离子缔合物褪色光度法测定痕量铋(Ⅲ)

基于 p H=5.50弱酸性介质中 ,铋 ( )催化 K2 S2 O8氧化 [Ag(phen) 2 ]+ · [FIn]-离子缔合物的褪色反应 ,建立了一种催化褪色光度法测定痕量铋 ( )的新方法。该方法线性范围为 0 .0 4— 0 .4 mg/ L,检出限为 6 .0× 10 -11g/ m L。用于发样及水样中 Bi( )的测定 ,获得了令人满意的结果 ,并对反应的机理进行了探讨。     

酸性品红褪色光度法测定痕量铁(Ⅲ)

基于Fe(Ⅲ)可使酸性品红氧化褪色,建立了一种褪色光度法测定铁的新方法,该方法线性范围为0-8.25μg/mL,检出限为3.72×10-4μg/mL.用于水样中Fe(Ⅲ)含量的测定,回收率在90%-100%.     

催化动力学光度法测定铝合金中痕量钛

本文研究了在硝酸介质中 ,痕量 Ti( )催化过氧化氢氧化甲基橙褪色的指示反应。优选出催化褪色反应的最佳条件 ,建立了测定痕量钛的新方法。方法的检出限为 4 .8× 10 -11g/ m L,测定范围为 0—0 .88μg/ 2 5m L,用于测定铝合金中的痕量 Ti( ) ,获得了满意的结果     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.