Ag nanoparticles prepared by laser photoreduction as substrates for in situ surface-enhanced Raman scattering analysis of dyes

In this work Ag nanoparticles (AgNP) with surface-enhanced Raman scattering (SERS) activity were prepared and immobilized by laser irradiation on a water/ solid interface where the aqueous phase contains the Ag+ cation and the solid surface is of hydrophilic nature (glass and cellulose). The so-prepared AgNP demonstrated a high SERS effectiveness in the detection of dispersed adsorbates such as the case of the anthraquinonic dye alizarin. The size and SERS effectiveness of AgNP increases with the irradiation time, the laser power, and the cation concentration. Laser-induced AgNP can be classified into two classes attending to the morphology: spherical and planar. The latter are formed after longer irradiation times, being more active regarding the SERS efficiency. Ag photoreduction can be employed for in situ detection of the dye alizarin, but when the dye is placed on a hydrophilic substrate. Even so, this in situ SERS technique could be attractive for analytical applications involving the in situ detection of the analyzed species, such as the case of dyes in artistical objects, textiles, foods, and surface analysis in general.     

Plasma-induced formation of Ag nanodots for ultra-high-enhancement surface-enhanced Raman scattering substrates

We report here plasma-induced formation of Ag nanostructures for surface-enhanced Raman scattering (SERS) applications. An array of uniform Ag patterned structures of 150 nm diameter was first fabricated on a silicon substrate with imprint lithography; then the substrate was further treated with an oxygen plasma to fracture the patterned structures into clusters of smaller, interconnected, closely packed Ag nanoparticles (20-60 nm) and redeposited Ag nanodots ( approximately 10 nm) between the clusters. The substrate thus formed had a uniform ultrahigh SERS enhancement factor (1010) over the entire substrate for 4-mercaptophenol molecules. By comparison, Au patterned structures fabricated with the same method did not undergo such a morphological change after the plasma treatment and showed no enhancement of Raman scattering.     

Anisotropic wetting on microstrips surface fabricated by femtosecond laser

In this paper, we present a new method to realize anisotropy by restricting a droplet on an unstructured Si hydrophobic domain between two superhydrophobic strips fabricated by femtosecond laser. The water contact angles and corresponding water baseline length were investigated. The results showed that anisotropy would vary with the volume-induced pinning-depinning-repinning behavior of the droplet. Furthermore, through the observation of water response on small Si domain, the adhesive force of the structure is proven to be the key factor giving rise to the anisotropy wetting. This phenomenon could potentially be used as a model for fundamental research, and such structures could be utilized to control large volume in microfluidic devices, lab-on-chip system, microreactors, and self-cleaning surfaces.     

Novel fabrication of Ag thin film on glass for efficient surface-enhanced Raman scattering

This paper describes a very simple electroless-plating method used to prepare optically tunable nanostructured Ag films. Very stable Ag films can be reproducibly fabricated simply by soaking glass substrates in ethanolic solutions of AgNO3 and butylamine. The grain size of silver can be readily controlled to range from 20 to 150 nm, and these nanostructural features correlated well with their UV/vis absorption characteristics, as well as with their surface-enhanced Raman scattering (SERS) activities. It is also very advantageous that the Ag films prepared exhibit very even SERS activity over an area up to hundreds thousand square-micrometers, and the enhancement factor estimated using benzenethiol as a prototype adsorbate reaches approximately 2 x 10(5). Since the proposed method is cost-effective and is suitable for the mass production of diverse Ag films irrespective of the shapes of the underlying substrates, it is expected to play a significant role in the development of surface plasmon-based analytical devices.     

Role of nanoparticle surface charge in surface-enhanced Raman scattering

In this work, the role of nanoparticle surface charge in surface-enhanced Raman scattering (SERS) is examined for the common case of measurements made in colloidal solutions of Ag and Au. Average SERS intensities obtained for several analytes (salicylic acid, pyridine, and 2-naphthalenethiol) on Ag and Au colloids are correlated with the pH and zeta potential (zeta) values of the nanoparticle solutions from which they were recorded. The consequence of the electrostatic interaction between the analyte and the metallic nanoparticle is stressed. The zeta potentials of three commonly used colloidal solutions are reported as a function of pH, and a discussion is given on how these influence SERS intensity. Also examined is the importance of nanoparticle aggregation (and colloidal solution collapse) in determining SERS intensities, and how this varies with the pH of the solution. The results show that SERS enhancement is highest at zeta potential values where the colloidal nanoparticle solutions are most stable and where the electrostatic repulsion between the particles and the analyte molecules is minimized. These results suggest some important criteria for consideration in all SERS measurements and also provide important insights into the problem of predicting SERS activities for different molecular systems.     

Nanoparticle-mirror sandwich substrates for surface-enhanced Raman scattering

Sandwich surface-enhanced Raman scattering (SERS) substrates (3S) utilizing coupling between continuous metal films and plasmonic particles were fabricated using silver mirrors, electrochemically roughened films, and various sizes of silver nanoparticles. The effect of excitation wavelength and nanoparticle size on SERS spectra of poly(vinylpyridine), selected as a model compound, was studied to determine the optimum conditions for the strongest SERS signal. The Raman enhancement resulted from the plasmon coupling of silver nanoparticles to the underlying continuous film as well as the lateral plasmon coupling between the silver nanoparticles. The formation of the charge transfer complex was also observed. The 3S configuration was used to obtain SERS spectra of dipicolinic acid (DPA), a chemical signature for Bacillus anthracis.     

Silver nanovoid arrays for surface-enhanced Raman scattering

Highly ordered silver nanovoid arrays are fabricated on porous anodic alumina membranes to produce robust and cost-efficient surface-enhanced Raman scattering (SERS) substrates. Plasmonic tunability can be accomplished by adjusting the topography with different anode voltages. Evenly distributed plasmonic fields, high average enhancement factor, and excellent ambient stability due to the natural protective layer are some of the unique advantages, and the silver nanovoid arrays are applicable to sensing devices.     

Multiobjective evolutionary optimisation for surface-enhanced Raman scattering

In most optimisation experiments, a single parameter is first optimised before a second and then third one are subsequently modified to give the best result. By contrast, we believe that simultaneous multiobjective optimisation is more powerful; therefore, an optimisation of the experimental conditions for the colloidal SERS detection of l-cysteine was carried out. Six aggregating agents and three different colloids (citrate, borohydride and hydroxylamine reduced silver) were tested over a wide range of concentrations for the enhancement and the reproducibility of the spectra produced. The optimisation was carried out using two methods, a full factorial design (FF, a standard method from the experimental design literature) and, for the first time, a multiobjective evolutionary algorithm (MOEA), a method more usually applied to optimisation problems in computer science. Simulation results suggest that the evolutionary approach significantly out-performs random sampling. Real experiments applying the evolutionary method to the SERS optimisation problem led to a 32% improvement in enhancement and reproducibility compared with the FF method, using far fewer evaluations.     

Self-assembled silver nanochains for surface-enhanced Raman scattering

Surface-enhanced Raman scattering (SERS) integrates high levels of sensitivity with spectroscopic precision and has tremendous potential for chemical and biomolecular sensing. The key to the wider application of Raman spectroscopy using roughened metallic surfaces is the development of highly enhancing substrates for analytical purposes. Here, we demonstrate a simple strategy for self-assembling silver nanochains on glass substrates for sensitive SERS substrates. The chain length of short Ag nanochains can be controlled by adjusting the concentration of cetyltrimethylammonium bromide (CTAB) and 11-mercaptoundecanoic acid (MUA). CTAB with appropriate concentration serves as the "glue" that can link the {100} facets of two neighboring Ag nanoparticles. MUA is found to be effective in "freezing up" the aggregation of Ag short chains and preventing them from further aggregating into a long chainlike network structure. The surface plasmon bands can be tuned over an extended wavelength range by controlling the length of the nanochains. The Ag monolayer, mainly composed of four-particle nanochains, exhibited the maximum SERS enhancement factor of around 2.6 x 108, indicating that a stronger SERS enhancement can be obtained in these interstitial sites of chainlike aggregated Ag nanoparticles.     

Adsorption of -histidine on copper surface as evidenced by surface-enhanced Raman scattering spectroscopy

The adsorption of -histidine on a copper electrode from H₂O- and D₂O-based solutions is studied by means of surface-enhanced Raman scattering (SERS) spectroscopy. Different adsorption states of histidine are observed depending upon pH, potential, and the presence of the SO²⁻₄ and Cl⁻ ions. In acidic solutions of pH 1.2 the imidazole ring of the adsorbed histidine remains protonated and is not involved in the chemical coordination with the surface. The SO²⁻₄ and Cl⁻ ions compete with histidine for the adsorption sites. In solutions of pH 3.1 three different adsorption states of histidine are observed depending on the potential. Histidine adsorbs with the protonated imidazole ring oriented mainly perpendicularly to the surface at potentials more positive than −0.2 V. Transformation of that adsorption state occurs at more negative potentials. As this takes place, histidine adsorbs through the α-NH₂ group and the neutral imidazole ring. The Cl⁻ ions cause the protonation and detachment of the α-NH₂ group from the surface and the formation of the ion pair NH⁺₃ … Cl⁻ can be observed. In the neutral solution of pH 7.0 histidine adsorbs through the deprotonated nitrogen atom of the imidazole ring and the α-COO⁻ group at E ≥ −0.2 V. However, this adsorption state is transformed into the adsorption state in which the α-NH₂ group and/or neutral imidazole ring participate in the anchoring of histidine to the surface, once the potential becomes more negative. In alkaline solutions of pH 11.9 histidine is adsorbed on the copper surface through the neutral imidazole ring.     

等离激元激励表面增强拉曼光谱检测技术与仪器

本文总结了近年来基于传播型表面等离激元（Propagafingsurfaceplasmons,PSPs）参与的表面增强拉曼（Surface—enhancedRamanscattering,SERS）技术和仪器方面的研究进展．内容主要包括3部分：（1）基于PSPs激励拉曼散射的装置和技术,包括在消逝场下激发PSPs共振增强拉曼的原理与装置、与表面等离子体共振（Surfaceplasmonresonance,SPR）传感技术的联用及新型结构的长程等离激元激励拉曼技术的研究进展;（2）通过引入局域型表面等离激元（Localizedsurfaceplasmons,LSPs）进一步增强SERS,进而实现PSPs-LSPs共同增强拉曼的超灵敏检测技术,包括在消逝场激发的PSPs基础上,增加纳米粒子实现的PSPs与LSPs共同增强拉曼的原理、装置,以及用该方法进行生物体系的免疫识别检测,此外,还在微纳周期结构上实现了PSPs与LSPs共同激励拉曼;（3）基于PSPs耦合的定向SERS技术,包括在消逝场结构和周期结构上实现SERS定向耦合发射以达到高激发和高收集效率的新技术．     

Trace molecules detectable by surface-enhanced Raman scattering based on newly developed Ag and Au nanoparticles-containing substrates

In this work, Ag and Au nanoparticles-containing substrates were first developed for obtaining a stronger surface-enhanced Raman scattering (SERS) intensity of Rhodamine 6G (R6G) and reducing the limit of detection (LOD) of trace molecules. First, the optimum electrochemically roughening conditions employed on Ag substrates for obtaining strongest SERS of R6G were investigated. Then the optimally roughened Ag substrates were incubated in the prepared Cl- and Au-containing solutions for different couples of minutes to undergo the galvanic replacement reactions. Encouragingly, the SERS of R6G adsorbed on this roughened Ag substrate modified by the replacement of Ag with Au for 5 min exhibits a higher intensity by 8-fold of magnitude, as compared with the SERS of R6G adsorbed on an unmodified roughened Ag substrate. Moreover, the practical LOD of R6G can be reduced by one order of magnitude from 1 ppq to 0.1 ppq. Further investigations indicate that the compositions of complexes formed on the substrates demonstrate decided effects on the improved SERS.     

Convective assembly of bacteria for surface-enhanced Raman scattering

A sample preparation method based on convective assembly for "whole-microorganism" identification using surface-enhanced Raman scattering (SERS) is developed. With this technique, a uniform sample can easily be prepared with silver nanoparticles. During the deposition process, bacteria and nanoparticles are assembled to form a unique well-ordered structure with great reproducibility. The SERS spectra acquired from the samples prepared with this technique have better quality and improved reproducibility for SERS spectra obtained from the same sample and limited variation due to the consistent sample preparation. E. coli, a Gram-negative bacilli, and Staphylococcus cohnii, a Gram-positive coccus, are studied as model bacteria.     

Gold-silver bimetallic porous nanowires for surface-enhanced Raman scattering

Highly porous bimetallic nanowires manufactured via a simple galvanic reaction have demonstrated superior activity in surface-enhanced Raman scattering, allowing ultrasensitive chemical detections on isolated porous nanowires in comparison to pristine silver nanowires.     

pH effect on surface potential of polyelectrolytes-capped gold nanoparticles probed by surface-enhanced Raman scattering

Nanoparticles are commonly stabilized through the adsorption of acidic/basic polyelectrolytes around the surface of the particle. One example of these nanoparticles is poly(ethylenimine) (PEI)-capped Au nanoparticles. In this work, we have examined by means of surface-enhanced Raman scattering (SERS) of 2,6-dimethylphenylisocyanide (2,6-DMPI) how much the surface potential of Au nanoparticles is affected by the solution pH through the mediation of the protonation and deprotonation of PEI in contact with Au nanoparticles. In fact, the surface-potential-dependent isocyanide (NC) stretching peak of 2,6-DMPI has shifted sharply around pH 8.5, close to the pK(a) value of the primary amine of PEI. When a negatively charged poly(acrylic acid) (PAA) was deposited onto the PEI, the peak shift of the NC stretching band took place around pH 6.5, close to the average pK(a) value of PEI and PAA. When additional PEI was deposited on PAA, the peak shift of the NC stretching band occurred once again around pH 8.5, indicative of the stronger interaction of upper two polyelectrolyte layers. These data clearly illustrate the usefulness of SERS in the elucidation of a delicate interaction of cationic and anionic polyelectrolytes, especially in layer-by-layer deposition.     

Electronic structure methods for studying surface-enhanced Raman scattering

This critical review highlights recent advances in using electronic structure methods to study surface-enhanced Raman scattering. Examples showing how electronic structure methods, in particular time-dependent density functional theory, can be used to gain microscopic insights into the enhancement mechanism are presented (150 references).     

The theory of surface-enhanced Raman scattering

By considering the molecule and metal to form a conjoined system, we derive an expression for the observed Raman spectrum in surface-enhanced Raman scattering. The metal levels are considered to consist of a continuum with levels filled up to the Fermi level, and empty above, while the molecule has discrete levels filled up to the highest occupied orbital, and empty above that. It is presumed that the Fermi level of the metal lies between the highest filled and the lowest unfilled level of the molecule. The molecule levels are then coupled to the metal continuum both in the filled and unfilled levels, and using the solutions to this problem provided by Fano, we derive an expression for the transition amplitude between the ground stationary state and some excited stationary state of the molecule-metal system. It is shown that three resonances contribute to the overall enhancement; namely, the surface plasmon resonance, the molecular resonances, as well as charge-transfer resonances between the molecule and metal. Furthermore, these resonances are linked by terms in the numerator, which result in SERS selection rules. These linked resonances cannot be separated, accounting for many of the observed SERS phenomena. The molecule-metal coupling is interpreted in terms of a deformation potential which is compared to the Herzberg-Teller vibronic coupling constant. We show that one term in the sum involves coupling between the surface plasmon transition dipole and the molecular transition dipole. They are coupled through the deformation potential connecting to charge-transfer states. Another term is shown to involve coupling between the charge-transfer transition and the molecular transition dipoles. These are coupled by the deformation potential connecting to plasmon resonance states. By applying the selection rules to the cases of dimer and trimer nanoparticles we show that the SERS spectrum can vary considerably with excitation wavelength, depending on which plasmon and/or charge-transfer resonance is excited.     

有序Au/Ag纳米碗阵列的简易制备及其表面增强拉曼散射性能

通过湿法化学合成基于SiO₂胶体晶体的大面积有序Au/Ag纳米碗(Au/AgNB)阵列。首先,在玻璃基板上组装3D SiO₂胶体晶体作为模板。然后,以Au纳米颗粒(AuNP)为种子,通过原位生长法在SiO₂模板上沉积一层Au纳米壳(AuNS)。再通过HCHO还原Ag⁺成Ag⁰,进一步在AuNS表面沉积Ag纳米壳,形成Ag/Au双纳米壳(Ag/AuNS)阵列。最后通过丙烯酸酯改性双向取向聚丙烯(BOPP)膜方便地获得了单层有序反转Ag/AuNB阵列。这种有序Au/AgNB阵列具有更佳的表面增强拉曼散射(SERS)活性,其SERS分析增强因子(AEF)可达2.23×10⁷。     

Sensing of 2,4-dichlorophenoxyacetic acid by surface-enhanced Raman scattering

Surface-enhanced Raman scattering (SERS) spectra of the herbicide 2,4-dichlorophenoxyacetic acid (2,4-D) was obtained by employing a bi-layer gold substrate, assembled by the reduction of Au(III) over gold-seeded nanoparticles immobilized on functionalized glass substrates. The SERS signal was linear with the logarithm of the solution concentrations between 1.0 × 10⁻⁷ mol L⁻¹ and 1.0 × 10⁻³ mol L⁻¹, indicating that the bi-layer gold substrate affords a significant dynamic range for SERS, providing an excellent analytical response within this concentration range, and revealing the high sensitivity of the gold surface towards such analyte. In addition, using the same gold substrate, a similar calibration curve was obtained for crystal-violet (CV), and it was possible to identify the concentration limit corresponding to the transition from the average SERS to the nonlinear SERS response.