Application of multiwalled carbon nanotubes as solid phase extraction sorbent for preconcentration of trace copper in water samples

The adsorption behavior of multiwalled carbon nanotubes (MWNTs) toward copper has been investigated systemically, and a new method has been developed for the determination of trace copper in water samples based on preconcentration with a microcolumn packed with MWNTs prior to its determination by flame atomic absorption spectrometry. The optimum experimental parameters for preconcentration of copper, such as pH of the sample, sample flow rate and volume, elution solution and interfering ions, have been investigated. Copper can be quantitatively retained by MWNTs in the pH range 5-8, and then eluted completely with 0.5 M HNO3. The detection limit of this method for Cu was 0.42 ng/mL, and the RSD was 3.5% at the 10 ng/mL Cu level. The method was validated using a certified reference material, and has been successfully applied for the determination of trace copper in water samples.     

羧基化多壁碳纳米管固相萃取-液相色谱-串联质谱法测定环境水体中四溴双酚A和双酚A

建立了羧基化碳纳米管固相萃取-液相色谱-串联质谱联用检测环境水体中四溴双酚A和双酚A的方法。比较了多壁碳纳米管、C60和羧基化多壁碳纳米管作为固相吸附剂对水体中四溴双酚A和双酚A的吸附效率。固相萃取浓缩后的样品经Thermo Scientific Hypersil C18色谱柱（150 mm×4.6 mm,3 μm）分离,采用串联质谱负离子模式进行检测。结果表明,四溴双酚A和双酚A在0.02~1.0 mg/L范围内具有良好的线性关系（r²≥0.99）,空白样品中的检出限（S/N=3）分别为0.04 μg/L和0.2 μg/L。将所建立的方法应用于实际环境水体中四溴双酚A和双酚A的检测,添加回收率在82%~99%之间,精密度小于5.0%,该方法可用于复杂环境样品中痕量四溴双酚A和双酚A的检测。     

Application of NaClO-treated multiwalled carbon nanotubes as solid phase extraction sorbents for preconcentration of trace 2,4-dichlorophenoxyacetic acid in aqueous samples

Multiwalled carbon nanotubes functionalized by oxidation of original multiwalled carbon nanotubes with NaClO were prepared and their application as solid phase extraction sorbent for 2,4-dichlorophenoxyacetic acid (2,4-D) was investigated systemically, and a new method was developed for the determination of trace 2,4-D in water samples based on extraction and preconcentration of 2,4-D with solid phase extraction columns packed with NaClO-treated multiwalled carbon nanotubes prior to its determination by HPLC. The optimum experimental parameters for preconcentration of 2,4-D, including the column activating conditions, the amount of the sorbent, pH of the sample, elution composition, and elution volume, were investigated. The results indicated 2,4-D could be quantitatively retained by 100 mg NaClO-treated multiwalled carbon nanotubes at pH 5, and then eluted completely with 10 mL 3:1 (v/v) methanol-ammonium acetate solution (0.3 mol/L). The detection limit of this method for 2,4-D was 0.15 μg/L, and the relative standard deviation was 2.3% for fortified tap water samples and 2.5% for fortified riverine water sample at the 10 μg/L level. The method was validated using fortified tap water and riverine water samples with known amount of 2,4-D at the 0.4, 10, and 30 μg/L levels, respectively.     

Solid-phase extraction using multiwalled carbon nanotubes and quinalizarin for preconcentration and determination of trace amounts of some heavy metals in food,water and environmental samples

A solid phase extraction procedure has been developed using multiwalled carbon nanotubes (MWCNTs) as a solid sorbent and quinalizarin [1,2,5,8-tetrahydroxyanthracene-9,10-dione] as a chelating agent for separation and preconcentration of trace amounts of some heavy metal ions, Cd(II), Cu(II), Ni(II), Pb(II) and Zn(II) before their determination by flame atomic absorption spectroscopy (FAAS). The influences of the analytical parameters, including pH, amounts of quinalizarin and adsorbent, sample volume, elution conditions such as volume and concentration of eluent, flow rates of solution and matrix ions, were investigated for the optimum recoveries of the analyte ions. No interference effects were observed from the foreign metal ions. The preconcentration factor was 100. The detection limit (LOD) for the investigated metals at the optimal conditions were observed in the range of 0.30–0.65 μg L^?1. The relative standard deviation (RSDs), and the recoveries of standard addition for this method were lower than 5.0% and 96–102%, respectively. The new procedure was successfully applied to the determination of analytes in food, water and environmental samples with satisfactory results.     

Development of magnetic multiwalled carbon nanotubes as solid-phase extraction technique for the determination of p-hydroxybenzoates in beverage

In this work, magnetic multiwalled carbon nanotubes were synthesized through a facile hydrothermal process, and then successfully used as magnetic solid-phase extraction sorbents for the determination of p-hydroxybenzoates in beverage. The prepared magnetic multiwalled carbon nanotubes presented both satisfactory superparamagnetism and strong capacity of absorption, with magnetic Fe(3)O(4) beads of 200 nm average diameters decorated at either ends of the tubes. The hybrid nanocomposites showed a high efficiency in the extraction and enrichment of p-hydroxybenzoates via π-π stacking of targeted molecules onto the polyaromatic composed surface of multiwalled carbon nanotubes, which entitled them promising magnetic solid-phase extraction sorbents for p-hydroxybenzoates at trace level from complex drink samples. By using an external magnetic field, p-hydroxybenzoates adsorbed on magnetic multiwalled carbon nanotubes could be rapidly isolated in only 30 s, and subsequently analyzed by liquid chromatography-diode array detector after elution with organic solvents. Extraction conditions such as eluting solvent, the amounts of magnetic sorbents added, pH values, adsorption and desorption time were investigated and optimized to achieve the best effect. Method validations including linearity, detection limit, and precision were also studied. The linearities were in the wide range of 0.05-500 μg/mL with correlation coefficients higher than 0.9983 for all p-hydroxybenzoates. The limits of detection were less than 20 ng/mL. Acceptable RSDs were achieved within 5-8% for all analytes. The results indicated that the proposed method based on magnetic multiwalled carbon nanotubes as magnetic solid-phase extraction absorbents was rapid, efficient, and convenient for the analysis of the targeted compounds of p-hydroxybenzoates in beverage sample.     

Solid‐phase extraction disk based on multiwalled carbon nanotubes for the enrichment of targeted pesticides from aqueous samples

A sensitive method for the determination of six varying polarity pesticides (imidacloprid, acetamiprid, carbendazim, simazine, linuron, and tebufenozide) based on a solid‐phase extraction disk with multiwalled nanotubes is proposed.A dispersion of multiwalled nanotubes in a surfactant aqueous solution (Triton X‐100) was used for the preparation of the solid‐phase extraction disk. The effect of surfactant on the functional groups of multiwalled nanotubes was examined by applying temperature‐programmed desorption. It was found that this treatment increased the amount of oxygen groups of treated multiwalled nanotubes comparing with untreated ones. The factors that may influence the adsorption and recovery such as the kind and volume of eluent, volume, flow rate and pH of sample were investigated and optimized. Under the optimized conditions, the maximal enrichment factors for low polar pesticides are ranging from 4000 to 4985 and for more polar are 2250 and 2750. The linear range of calibration curves was 10–500 ng/L with correlation coefficient higher than 0.9960, and the detection limit was 6.2–23.7 ng/L. Finally optimized method was applied for determination trace level of five out of six pesticides in tap and river water samples with good recovery.     

Improvement of on-line solid-phase extraction for determining phenolic compounds in water

Summary Modifying the most common design for the on-line coupling of a precolumn to reversed phase LC with diode array detection has resulted in reduction of the broadening of the peaks which results when the compounds of interest are strongly retained by a highly hydrophobic sorbent. The modification consists of the desorption of the analytes trapped on the precolumn solely by the organic solvent used to modify the solvent strength of the mobile phase. Results obtained using this design were compared with those obtained with the conventional design, with C₁₈ and PLRP-S precolumns. The performance of the system was also tested with a highly cross-linked styrene-divinylbenzene copolymer (ENVI-chrom P) precolumn for the determination of phenolic compounds in real samples. The advantages and disadvantages are discussed. Ion-pair solid phase extraction is used in order to increase the breakthrough volumes of more polar compounds, mainly phenol. The use of the new design enables phenolic compounds to be determined at the low μg L⁻¹ level with limits of detection ranging between 0.1 and 2 μg L⁻¹ in tap water when a 10 mL sample was analyzed.     

High extraction efficiency for polar aromatic compounds in natural water samples using multiwalled carbon nanotubes/Nafion solid-phase microextraction coating

A novel solid-phase microextraction (SPME) fiber coated with multiwalled carbon nanotubes (MWCNTs)/Nafion was developed and applied for the extraction of polar aromatic compounds (PACs) in natural water samples. The characteristics and the application of this fiber were investigated. Electron microscope photographs indicated that the MWCNTs/Nafion coating with average thickness of 12.5 μm was homogeneous and porous. The MWCNTs/Nafion coated fiber exhibited higher extraction efficiency towards polar aromatic compounds compared to an 85 μm commercial PA fiber. SPME experimental conditions, such as fiber coating, extraction time, stirring rate, desorption temperature and desorption time, were optimized in order to improve the extraction efficiency. The calibration curves were linear from 0.01 to 10 μg mL⁻¹ for five PACs studied except p-nitroaniline (from 0.005 to 10 μg mL⁻¹) and m-cresol (from 0.001 to 10 μg mL⁻¹), and detection limits were within the range of 0.03–0.57 ng mL⁻¹. Single fiber and fiber-to-fiber reproducibility were less than 7.5 (n = 7) and 10.0% (n = 5), respectively. The recovery of the PACs spiked in natural water samples at 1 μg mL⁻¹ ranged from 83.3 to 106.0%.     

Chemically bonded multiwalled carbon nanotubes as efficient material for solid phase extraction of some metal ions in food samples

Multiwalled carbon nanotubes chemically functionalized with 2-((3-silylpropylimino) methyl) phenol (SPIMP-MWCNT) and successfully applied for the solid phase extraction (SPE) of some metal ions in food samples. The influences of the analytical parameters including pH, amounts of solid phase, eluent conditions (type, volume and concentrations), sample volume and interference of some metal ions on the recoveries of ions Cu²⁺, Pb²⁺, Fe²⁺, Ni²⁺ and Zn²⁺ ion were investigated. The metal ions retained on SPIMP-MWCNT was eluted using 6?mL of 4?mol?L^?1 HNO₃ solution and their content was determined by flame atomic absorption spectrometry (FAAS) with recoveries more than 95% and relative standard deviations (n?=?5) between 2.4–3.4% for both reproducibility and repeatability. The detection limit of this metal ions was between 1.0–2.6?ng?mL^?1 (3S _b , n?=?10) and their preconcentration factor was 100, while their loading capacity was above 32.9?mg?g^?1 of SPIMP-MWCNT. The proposed method was successfully applied for the preconcentration and determination of analytes in different samples.     

Novel modified carbon nanotubes as a selective sorbent for preconcentration and determination of trace copper ions in fruit samples

In this work, multiwalled carbon nanotubes were reacted with N‐[3‐(triet‐hoxysilyl)propyl]isonicotinamide to prepare pyridine‐functionalized carbon nanotubes. This novel sorbent was characterized by infrared spectroscopy, thermal and elemental analysis, and scanning electron microscopy. Functionalized carbon nanotubes were applied for the preconcentration and determination of copper ions using flame atomic absorption spectrometry. Various parameters such as sample pH, flow rate, eluent type and concentration, and its volume were optimized. Under optimal experimental conditions, the limit of detection, the relative standard deviation, and the recovery of the method were 0.65 ng/mL, 3.2% and 99.4%, respectively. After validating the method using standard reference materials, the new sorbent was applied for the extraction and determination of trace copper(II) ions in fruit samples.     

Preconcentration of diazinon using multiwalled carbon nanotubes as solid-phase extraction adsorbents

A sensitive and selective column adsorption method is proposed for the preconcentration and determination of diazinon. Diazinon was preconcentrated on multiwalled carbon nanotubes (MWCNTs) as an adsorbent and then determined by high-performance liquid chromatography (HPLC). Several parameters on the recovery of the analyte were investigated. The experimental results showed that it was possible to obtain quantitative analysis when the solution pH was 6 using 200 mL of validation solution containing 2 μg of diazinon and 5 mL of acetonitrile as an eluent. Recovery of diazinon was 95.2 ± 4.2% with a relative standard deviation for seven determinations of 4.9% under optimum conditions. The maximum preconcentration factor was 200 for diazinon when 1000 mL of sample solution volume was used. The linear range of calibration curve was 0.3 to 10,000 ng mL^− 1 with a correlation coefficient of 0.997 and the detection limit (3S/N) was 0.06 ng mL^− 1. The proposed method was successfully applied to the determination of diazinon in tap water with high precision and accuracy.     

Multiwalled carbon nanotubes as solid-phase extraction materials for the gas chromatographic determination of organophosphorus pesticides in waters

In the present work, a GC method with nitrogen-phosphorus detection (NPD) was developed for the simultaneous determination of eight organophosphorus pesticide (OPP) residues (i.e., ethoprofos, diazinon, chlorpyrifos-methyl, fenitrothion, malathion, chlorpyrifos, fenamiphos, and buprofezin) in water samples. Preconcentration of the water samples was carried out using an SPE procedure with multiwalled carbon nanotubes (MWCNTs) of 10-15 nm od, 2-6 nm id, and 0.1-10 microm length as stationary phase. Extraction parameters, such as the amount of MWCNTs, sample volume, pH, and type and amount of the eluent were optimized. The most favorable conditions were as follows: 40 mg MWCNTs, 800 mL water, pH 6.0, and 20 mL dichloromethane, respectively. The MWCNTs-SPE-GC-NPD method was applied to the determination of these pesticides in real water samples: mineral and ground water as well as run-off water from an agricultural area collected shortly before opening out onto the sea. A recovery study was developed with five consecutive extractions of the three types of water spiked at three concentration levels (n = 15). Mean recovery values were in the range of 75-116% for mineral water (RSD < 6.3%), 67-119% for ground water (RSD < 5.8%), and 57-81% for run-off waters (RSDs < 6.9%), except for fenamiphos (mean recovery values between 40 and 84% for the three types of waters, RSDs < 8.9%). LODs were in the low ng/L level (i.e., levels below the maximum residue limits (MRLs) established by the European Union (EU) legislation for these compounds in waters). The proposed method was also applied to the analysis of six water samples (two of each type: mineral, ground, and run-off waters) in which no residues of the selected pesticides were found. Results show that the MWCNTs used in this work have a high adsorbability of the pesticides under study. The main advantage of the use of these MWCNTs is their low cost when compared with those MWCNTs previously used in the literature and with conventional SPE cartridges.     

The isolation of basic proteins by solid-phase extraction with multiwalled carbon nanotubes

Multiwalled carbon nanotubes (MWCNTs) have been employed for the first time as sorbents for the isolation of basic proteins from other protein species in biological sample matrices by solid-phase extraction (SPE). A microcolumn packed with MWCNTs was incorporated after appropriate pretreatment into a sequential injection system, which facilitates online selective sorption of basic protein species (hemoglobin and cytochrome c in this particular case). The retained protein species were afterwards separated from each other by sequential elution from the microcolumn through the employment of appropriate eluents. A 0.025 mol L(-1) phosphate buffer solution of pH 8.0 facilitated the efficient collection of hemoglobin, while a 0.5 mol L(-1) NaCl solution ensured the quantitative recovery of the retained cytochrome c. With a sample loading volume of 2.0 mL, enrichment factors of 11 and 15 were derived for hemoglobin and cytochrome c, along with retention efficiencies of 100% for both species and recovery rates of 98 and 90%, respectively. A sampling frequency of 8 h(-1) was achieved, and the precisions were 3.0% and 0.8% (RSD) for hemoglobin and cytochrome c at a concentration of 5.0 microg mL(-1). The practical applicability of this system was demonstrated by processing of human whole blood for isolation of hemoglobin, and satisfactory results were obtained by assay with SDS-PAGE.     

Polypyrrole–montmorillonite nanocomposite as sorbent for solid‐phase microextraction of phenolic compounds in water

A fiber‐coated polypyrrole–montmorillonite nanocomposite was prepared for solid‐phase microextraction. The fiber coating can be prepared easily; it is mechanically stable and exhibits relatively high thermal stability. The prepared fiber was evaluated for the extraction of some phenolic compounds from aqueous sample solutions by gas chromatography–mass spectrometry. The effects of the extraction and desorption parameters including extraction time, extraction temperature, stirring rate, ionic strength, pH and desorption temperature and time have been studied. At optimum conditions, the repeatability for one fiber (n = 5), expressed as % relative standard deviation was between 6.5 and 7.8% for the phenolic compounds. The detection limits for the studied phenolic compounds were between 0.05–1.3 ng/mL. The developed method offers the advantage of being simple to use, with shorter analysis time, lower cost, thermal stability of the fibers, and high relative recovery in comparison to conventional methods of analysis.     

Determination of pesticide residues in complex matrices using multi-walled carbon nanotubes as reversed-dispersive solid-phase extraction sorbent

A modified quick, easy, cheap, effective, rugged and safe (QuEChERS) method with multi-walled carbon nanotubes (MWCNTs) as a reversed-dispersive solid-phase extraction (r-DSPE) material combined with gas chromatography-mass spectrometry was developed for the determination of 14 pesticides in complex matrices. Four vegetables (leek, onion, ginger and garlic) were selected as the complex matrices for validating this new method. This technique involved the acetonitrile-based sample preparation and MWCNTs were used as the r-DSPE material in the cleanup step. Two important parameters influencing the MWCNTs efficiency, the external diameters and the amount of MWCNTs used, were investigated. Under the optimized conditions, recoveries of 78-110% were obtained for the target analytes in the complex matrices at two concentration levels of 0.02 and 0.2 mg/kg. In addition, the RSD values ranged from 1 to 13%. LOQs and LODs for 14 pesticides ranged from 2 to 20 μg/kg and from 1 to 6 μg/kg, respectively.     

A novel polymeric ionic liquid-coated magnetic multiwalled carbon nanotubes for the solid-phase extraction of Cu,Zn-superoxide dismutase

A novel magnetic adsorbent, benzyl groups functionalized imidazolium-based polymeric ionic liquid (PIL)-coated magnetic multiwalled carbon nanotubes (MWCNTs) (m-MWCNTs@PIL), has been successfully synthesized and applied for the extraction of Cu, Zn-superoxide dismutase (Cu, Zn-SOD). The m-MWCNTs@PIL were characterized by X-ray diffraction (XRD), Fourier transform infrared spectrometry (FT-IR), thermal gravimetric analysis (TGA), field emission scanning electron microscopy (FESEM), vibrating sample magnetometer (VSM) and zeta-potential nanoparticles. In this method, the m-MWCNTs@PIL could interact with Cu, Zn-SOD through hydrogen bonding, π-π and electrostatic interactions. The extraction performance of the m-MWCNTs@PIL in the magnetic solid-phase extraction (MSPE) procedure was investigated, coupled with the determination by UV–vis spectrophotometer. Compared with m-MWCNTs@IL and m-MWCNTs, the m-MWCNTs@PIL exhibited the highest extraction capacity of 29.1 mg/g for Cu, Zn-SOD. The adsorbed Cu, Zn-SOD remained high specific activity after being eluted from m-MWCNTs@PIL by 1 moL/L NaCl solution. Besides, the m-MWCNTs@PIL could be easily recycled and successfully employed in the extraction of Cu, Zn-SOD from real samples. Under the optimal conditions, the precision, repeatability and stability of the proposed method were investigated and the RSDs were 0.29%, 1.68% and 0.54%, respectively. Recoveries were in the range of 82.7–102.3%, with the RSD between 3.47% and 5.35%. On the basis of these results, the developed method has great potential in the extraction of Cu, Zn-SOD or other analytes from biological samples.     

Evaluation of carbon nanotubes as a solid-phase extraction adsorbent for the extraction of cephalosporins antibiotics, sulfonamides and phenolic compounds from aqueous solution

The adsorptive potential of carbon nanotubes (single-walled carbon nanotubes and multi-walled carbon nanotubes) for solid-phase extraction of three groups of highly polar compounds (namely cephalosporins antibiotics, sulfonamides and phenolic compounds) was tested in this article. The analytes were strongly retained by the carbon nanotubes. And acceptable recoveries were obtained with the addition of ammonium acetate into eluents. The effects of solution pH on the recoveries of the antibiotics and phenolic compounds were examined. To check the retention abilities of three groups of compounds on carbon nanotubes, fixed amount of each analyte was added to different volumes (up to 500 mL) of aqueous solution, and then extracted by the sorbents. Comparative studies showed that the carbon nanotubes were much superior to C₁₈ for the extraction of the highly polar analytes. For the cephalosporins antibiotics and sulfonamides, the carbon nanotubes showed stronger retention capability than graphitized carbon blacks, but for some of the phenolic compounds graphitized carbon blacks seemed to be more suitable, indicating different retention mechanisms of these analytes. To further assess the enrichment ability of carbon nanotubes for highly polar compounds, the solid-phase extraction method of multi-walled carbon nanotubes packed cartridge was well developed, and the sulfonamides were used as model compounds. Under the optimal procedures, the detection limits of sulfonamides were in the range of 27-38 ng L⁻¹. The spiked recoveries from several real water samples obtained for sulfathiazole and sulfadiazine ranged from 55% to 79% and 72% to 92%, respectively, while the recoveries of sulfapyridine and sulfamethazine were in the range of 85-102%.     

Surfactant‐coated graphitized multiwalled carbon nanotubes as the pseudostationary phase in electrokinetic chromatography for the analysis of phytochemical compounds in biological fluids

This report describes the use of surfactant‐coated graphitized multiwalled carbon nanotubes (SC‐GMWNTs) as a novel pseudostationary phase in CE with diode array detection for the determination of phenolic acids and tanshinones in herbal and urine samples. Several parameters influencing the separation were studied, such as the concentrations of SDS, GMWNTs, and isopropanol; choice of carbon nanotubes; sodium borate content; and buffer pH. The results revealed that the presence of SC‐GMWNTs in buffer enhanced the separation efficiency for the target analytes relative to conventional micelles due to the strong interaction between the surface of the GMWNTs and the target compounds. Under the optimum conditions, the method showed good linearity, with correlation coefficients higher than 0.9950. LODs were in the range of 0.71–3.10 μg/mL. Furthermore, satisfactory separations were achieved with good recovery values in the range of 89.97 and 103.30% when 10 mM borate, 30 mM SDS, 10% isopropanol, and 6 μg/mL SC‐GMWNTs were introduced into the buffer solution.     

Flame atomic absorption spectrometry for the determination of trace amount of rhodium after separation and preconcentration onto modified multiwalled carbon nanotubes as a new solid sorbent

The present article reports on the application of modified multiwalled carbon nanotubes (MMWCNTs) as a new, easily prepared and stable solid sorbent for the preconcentration of trace rhodium ion in aqueous solution. Rhodium ions were complexed with 1-(2-pyridylazo)-2-naphthol (PAN) in the pH range of 3.2-4.7 and then the formed Rh-PAN complex was adsorbed on the oxidized MWCNTs. The adsorbed complex was eluted from MWCNTs sorbent with 5.0 mL of N,N-dimethylformamide (DMF). The rhodium in eluted solution was determined by flame atomic absorption spectrometry (FAAS). Linear range for the determination of rhodium was maintained between 0.16 ng mL⁻¹ and 25.0 μg mL⁻¹ in initial solution. Relative standard deviation for the 10 replicated determination of 4.0 μg mL⁻¹ of rhodium was ±0.97%. Detection limit was 0.010 ng mL⁻¹ in initial solution (3S_bl, n = 10) and preconcentration factor was 120. Sensitivity for 1% absorbance of rhodium (III) was 0.112 μg mL⁻¹. The sorption capacity of oxidized MWCNTs for Rh (III) was 6.6 mg g⁻¹. The effects of the experimental parameters, including the sample pH, flow rates of sample and eluent solution, eluent type, breakthrough volume and interference ions were studied for the preconcentration of Rh³⁺. The proposed method was successfully applied to the extraction and determination of rhodium in different samples.