Voltammetric determination of phosphonate ion as a heteropoly complex

A simple voltammetric method for the determination of phosphonate ion is described. A 12-molybdodiphosphonate complex is formed in a 50mM Mo(VI)-0.5M HCl-70% (v/v) CH(3)CN system containing phosphonate ion. The yellow heteropolyanion undergoes apparent two-step reductions at a glassy carbon electrode. The voltammetric reduction currents depend linearly on the phosphonate concentration in the range 1 x 10(-5)-1 x 10(-3)M.     

Simultaneous determination of phosphonate, phosphate, and diphosphate by capillary electrophoresis using in-capillary complexation with Mo(VI)

This study describes the simultaneous determination of phosphonate, phosphate, and diphosphate by CE with direct UV detection, based on in-capillary complexation with Mo(VI). When a mixture of phosphonate, phosphate, and diphosphate was injected into a capillary containing 3.0 mM Mo(VI), 0.05 M malonate buffer (pH 3.0) and 45% v/v CH3CN, three well-defined peaks, due to the migration of the corresponding polyoxomolybdate anions, were separated. The respective calibration graphs were linear in the concentration range of 2 x 10(-6)-2 x 10(-4) M for phosphonate, 1 x 10(-6)-5 x 10(-5) M for phosphate, and 1 x 10(-6)-2 x 10(-4) M for diphosphate; the correlation coefficients were better than 0.9990. The present CE method is successfully applied to the simultaneous determination of phosphonate, phosphate, and diphosphate in tap water.     

A rapid spectrophotometric method for the determination of molybdenum in industrial, environmental, biological and soil samples using 5,7-dibromo-8-hydroxyquinoline.

A very simple, ultra-sensitive and highly selective non-extractive spectrophotometric method for the determination of trace amount of molybdenum(VI) using 5,7-dibromo-8-hydroxyquinoline (DBHQ) has been developed. 5,7-Dibromo-8-hydroxyquinoline reacts in a slightly acidic solution (0.05 - 1.0 M H2SO4) with molybdenum(VI) to give a deep greenish-yellow chelate which has an absorption maximum at 401 nm. The reaction is instantaneous and the absorbance remains stable for over 24 h. The average molar absorption coefficient and Sandell's sensitivity were found to be 4.13 x 10(3) L mol(-1) cm(-1) and 7 ng cm(-2) of molybdenum(VI), respectively. Linear calibration graphs were obtained for 0.1 - 50 microg mL(-1) of molybdenum(VI). The stoichiometric composition of the chelate is 1:3 (Mo:DBHQ). A large excess of over 50 cations, anions and some common complexing agents (e.g. EDTA, oxalate, citrate, phosphate, thiourea, SCN-) do not interfere with the determination. The method was successfully used in the determination of molybdenum in several Standard Reference Materials (alloys, steels and waters) as well as in some environmental waters (inland and surface), biological samples (human blood and urine), soil samples, solution containing both molybdenum(V) and molybdenum(VI) and complex synthetic mixtures. The method has high precision and accuracy (S = +/-0.01 for 0.5 microg mL(-1)).     

Capillary electrophoretic determination of phosphate based on the formation of a Keggin-type [PMo12O40]3- complex.

Based on the formation of a Keggin-type [PMo12O40]3- complex, a sensitive capillary electrophoresis (CE) method was developed for the determination of P(V) with direct UV detection at 220 nm. A mixture of alpha- and beta-Keggin-type [PMo12O40]3- complexes was readily formed in a sample solution consisting of a trace amount of P(V), 2.5 mM Mo(VI), 0.050 M p-C6H3(CH3)-2-SO3H (XSA), and 60% v/v CH3CN. When a 0.05 M HCl and 60% v/v CH3CN solution was used as a migration electrolyte, the Keggin complexes exhibited a sharp and well-defined peak in the electropherogram. The peak area was linearly dependent on the P(V) concentration in the range of 5 x 10(-7)-5 x 10(-5) M; a detection limit of 1 x 10(-7) M was achieved. In comparison with indirect UV detection, the direct UV detection is about ten times more sensitive, because the Keggin complexes possess high molar absorptivities. The developed CE method was applied to the determination of P(V) in river water, and the results were in good agreement with those obtained by ion chromatography (IC) and colorimetry (COL) based on the formation of mixed-valence heteropoly blue species.     

An atomic absorption spectrophotometric method for the determination of trace amounts of zinc in canned juices after ion exchange separation

An atomic absorption spectrophotometric method is described for the determination of microgram quantities of zinc in canned juices. After sample digestion in concentrated nitric acid, the solution is evaporated till near dryness, and then a solution of 2 M HCl is added to form tetrachlorozincate (II) ion. This acid solution, containing the zinc complex is passed through an ion-exchange column (anion exchange resin, chloride form, which is preconditioned by passing 1 M HCl solution). Zinc is eluted from the column with 0.01 M HCl solution. After evaporation to dryness, the residue is dissolved in 1% (v/v) HNO3, and then atomized into an air-acetylene flame. The limit of detection of the method is 0.15 micrograms ml-1 Zn. The analytical aspects of the proposed method, including the standard addition technique are discussed.     

The preconcentration, separation and spectrophotometric determination of traces of silicate

A method for the determination of traces of silicate based on the use of a strong base anion exchange in a preconcentration step and a batch-reactive stripping agent technique prior to spectrophotometric determination has been proposed. The reaction of molybdate and silicate in acidic solution to form 12-molybdosilicic acid permits recoveries exceeding 90% in analyzing solutions containing 0.02 to 0.1 μg of silicon/ml.     

An approach to the synthesis of polyoxometalate encapsulating different kinds of oxoanions as heteroions: bisphosphitopyrophosphatotriacontamolybdate [(HPO3)2(P2O7)Mo30O90]8-

A yellow [(HPO(3))(2)(P(2)O(7))Mo(30)O(90)](8-) anion was prepared as a tetrapropylammonium (Pr(4)N(+)) salt from a 50 mM Mo(VI)-2 mM P(2)O(7)(4-)-4 mM HPO(3)(2-)-0.95 M HCl-60% (v/v) CH(3)CN system at ambient temperature. The (Pr(4)N)(8)[(HPO(3))(2)(P(2)O(7))Mo(30)O(90)] salt crystallized in the orthorhombic space group P(nma) (No. 62), with a = 30.827(2) A, b = 22.8060(15) A, c = 30.928(2) A, V = 21743(3) A(3), and Z = 4. The structure contained a (P(2)O(7))Mo(12)O(42) fragment derived from the removal of each corner-shared Mo(3)O(13) unit in a polar position from a [(P(2)O(7))Mo(18)O(54)](4-) structure, and each side of the (P(2)O(7))Mo(12)O(42) fragment was capped by a B-type (HPO(3))Mo(9)O(24) unit. The [(HPO(3))(2)(P(2)O(7))Mo(30)O(90)](8-) anion was characterized by voltammetry and IR, UV-vis, and (31)P NMR spectroscopy. Unlike the Keggin and Dawson anions and the parent [(P(2)O(7))Mo(18)O(54)](4-) anion, the [(HPO(3))(2)(P(2)O(7))Mo(30)O(90)](8-) anion exhibited two-electron redox waves in CH(3)CN with and without acid.     

Salicylaldehyde Isonicotinoylhydrazone (SAIH) as a Specific Analytical Reagent for the Selective Extractive Spectrophotometric Determination of Molybdenum (VI) in Presence of Several Cations

Abstract

An extraction study of 36 cations with SAIH into isoamyl alcohol in the presence of EDTA, ascorbic acid and IN HC10₄ showed that only Mo(VI) gave a stable yellow colored complex extractable into the organic phase. This effect was used for the selective extractive spectrophotometric determination of Mo(VI) in the presence of other tested cations.     

Extraction,Spectrophotometric and Atomic Absorption Spectrophotometric Determination of Molybdenum with Caffeic Acid and Application in High Purity Grade Steel and Environmental Samples

Abstract

A new selective and sensitive method for extraction of yellow Mo (VI)-caffeic acid complex with a liquid ion exchanger, Aliquat 336 from 4.0 pH, and spectrophotometric determination of molybdenum in trace amounts is described. the molar absorptivity of the complex is 1.1 × 10⁵ 1 mol^?1 cm^?1 at 340 nm and the colour system obeys Beer's law in the range 0.04–0.99 ppm of Mo(VI). the molybdenum is also determined with AAS and the method is applied for its determination in steel and environmental samples.     

Determination of molybdenum by extraction of its thiocyanate into ethyl methyl ketone

A simple, sensitive and selective spectrophotometric method for determination of molybdenum is described. A solution containing 100 mug of Mo in 2.5M hydrochloric acid is treated with ascorbic acid and ammonium thiocyanate and after standing for 8 min is shaken with an equal volume of ethyl methyl ketone for 30 sec. The absorbance of the complex is measured at 465 nm against a reagent blank. The complex is stable for 1 hour. There is no interference from Re(VII), SO(2-)(4), Cl(-), CH(3)COO(-), PO(3-)(4), NO(-)(3), C(2)O(2-)(4), citrate or tartrate, and at least 5 mg of U(VI), 10 mg of Cr(III, VI), Th, or Ni, and 20 mg of W(VI) Can be tolerated. Vanadium(V) interferes at the 500 mug level, and fluoride slightly decreases the absorbance.     

Determination of Fe(III), Al(III), Mo(VI) and W(VI) with tetracycline by reversed-phase high-performance liquid chromatography

Tetracycline (TC) was used as a precolumn chelating reagent for reversed-phase high-performance liquid chromatographic (HPLC) separation and determination of Fe(III), Al(III), Mo(VI) and W(VI). The metal-TC chelates were separated on a Nucleosil C(18) (5 mum) column using a mobile phase of acetonitrile-water (21:79, v/v) containing citrate buffer and sodium chloride, nanogram levels of the metals could be determined by HPLC with satisfactory precision. The proposed method was applied to the simultaneous determination of Mo(VI) and W(VI) in mineral samples.     

Semimicro spectrophotometric determination of nitroglycerine in propellants by use of 2,4-xylenol

A semimicro spectrophotometric method using 2,4-xylenol is proposed for the determination of nitroglycerine in propellants. The propellant is extracted with methylene chloride, the extract is diluted, and a 10-ml aliquot is evaporated just to dryness. Then 2,4-xylenol reagent and 63% v/v sulphuric acid are added to hydrolyse the nitroglycerine to nitrate and form 6-nitro-2,4-xylenol which is steam-distilled in a Parnas-Wagner Kjeldahl distillation apparatus into a water-ammonia-isopropyl alcohol mixture. The absorbance of the yellow solution of the anion of the 6-nitro-2,4-xylenol is measured. The calibration curve is prepared from potassium nitrate and an empirical factor (5.50) is used to convert from nitrogen content to nitroglycerine (the theoretical factor is 5.40). The 2,4-xylenol should be added before the sulphuric acid in order to prevent interference from diphenylamine and ethyl centralite. The method is designed for the usual nitrocellulose double-base propellants containing 8-50% of nitroglycerine.     

Determination of melatonin and monoamines in rat pineal using reversed-phase ion-interaction chromatography with fluorescence detection

A method is reported for the ion-interaction, reversed-phase separation of 24 compounds (chiefly monoamines) arising from the metabolism of tyrosine and tryptophan. These compounds were separated as two groups. The first group comprised 3,4-dihydroxyphenylethylene glycol, tyrosine, 3-methoxy-4-hydroxyphenyl glycol, 5-hydroxytryptophan, norepinephrine, 3,4-dihydroxyphenylacetic acid, epinephrine, 5-hydroxyindole-3-acetic acid, homovanillic acid, 5-hydroxytryptophol, dopamine, tryptophan. N-acetylserotonin, N-acetyltryptophan, 5-methoxytryptophan and serotonin. The mobile phase consisted of a 6.8:93.2 (v/v) mixture of acetonitrile and an aqueous solution containing 0.16 M ammonium phosphate, 0.06 M citric acid, 0.15 mM disodium EDTA, 10 mM dibutylamine and 6 mM sodium 1-octanesulphonate at pH 4.50. The second group of compounds comprised 6-hydroxymelatonin, 5-methoxyindole-3-acetic acid, indole-3-acetic acid, 5-methoxytryptamine, tryptamine, 5-methoxytryptophol, melatonin and tryptophol. The mobile phase consisted of a 16:84 (v/v) mixture of acetonitrile and an aqueous solution containing 0.05 M ammonium phosphate, 0.05 M citric acid, 0.15 mM disodium EDTA, 25 mM dibutylamine and 5 mM sodium 1-octanesulphonate at pH 5.30. Detection was by fluorescence measurement (lambda ex = 280 nm, lambda em = 340 nm). The proposed method exhibited linear calibration over the biochemically significant concentration range, with detection limits in the 10-200 pg range. Excellent precision for peak areas and retention times was observed, even over a period of 24 h. The applicability of amperometric detection (at 0.72V) is also demonstrated. The method is applied to the determination of monoamines in individual rat pineals. Low nanogram levels of tyrosine, norepinephrine, 5-hydroxyindole-3-acetic acid, tryptophan, serotonin and 6-hydroxymelatonin, and picogram levels of 5-hydroxytryptophan, 5-hydroxytryptophol, 5-methoxyindole-3-acetic acid, indole 3-acetic acid, 5-methoxytryptophol and melatonin were indicated in most of the samples.     

Spectrophotometric determination of scandium with arsenazo

Arsenazo is used for the spectrophotometric determination of scandium in the range 10 to 50 μg. The absorbance is measured at 570 mμ and pH 6.1. A method is proposed for the successive determination of scandium and thorium. Scandium is separated from magnesium, calcium, rare earths, zirconium, fluoride, phosphate, and some other metals by extraction with TTA in xylene. Copper, aluminum, and iron(III) are removed by 8-quinolinol-chloroform extraction. Uranium(VI) is removed by anion exchange using hydrochloric acid. Thorium is separated from scandium by anion exchange using nitric acid.     

The separation of W(V) from HCl-KSCN medium on polyurethane foam sorbents for its spectrophotometric determination in steels and silicates

A simple procedure for selective sorption of tungsten is described. The method involves reduction of W(VI) to W(V) with tin(II) chloride (2%, w/v) at 8-9M hydrochloric acid, formation of the W(V)-SCN complex with 0.2M KSCN and its sorption on polyurethane foam within 20 min. The sorbed complex is then eluted with acidified acetone (1 ml of 1M hydrochloric acid and 8 ml of acetone) followed by addition of 1 ml of 0.1M KSCN to the eluent. The method has been applied to the spectrophotometric determination of tungsten in steels and silicates by measuring the absorbance of the eluted solution at 400 nm. Beer's law is obeyed for the range 0.1-12 mug W/ml. Other elements, e.g., Co(III) (50 mug/ml), Cu(II) (10 mug/ml), Ti(IV) (20 mug/ml), V(V) (10 mug/ml) and Mo(VI) (0.5 mug/ml) have no effect on the method. Interference of copper, up to 100 mug/ml has been eliminated by masking with thiourea and that due to molybdenum by prior separation with thioglycollic acid on PUF. The method has been verified with standard samples.     

Potentiometric flow-injection determination of trace hydrogen peroxide based on its induced reaction in iron(III)-iron(II) potential buffer containing bromide and molybdenum(VI)

A rapid and highly sensitive potentiometric flow-injection method for the determination of trace hydrogen peroxide was developed by use of an Fe(III)-Fe(II) potential buffer solution containing bromide and Mo(VI). The analytical method was based on a linear relationship between a concentration of hydrogen peroxide and a largely transient potential change of an oxidation-reduction potential electrode due to bromine generated by the reaction of hydrogen peroxide with the potential buffer solution. The oxidation of bromide to bromine by hydrogen peroxide occurred very rapidly with the assistance of Mo(VI) when Fe(II) existed in the potential buffer solution. It was estimated by batchwise experiments that hydroxyl radical, OH., was generated by the reaction of hydrogen peroxide with Fe(II) as an intermediate, and subsequently oxidized bromide to bromine. In a flow system, analytical sensitivities to hydrogen peroxide obtained by the detection of the transient change of potential were enhanced about 75 fold compared with those obtained by using the potential change caused by the reaction of hydrogen peroxide with the potential buffer solution without bromide and Mo(VI). Sensitivities increased with decreasing concentration of the Fe(III)-Fe(II) buffer in the reagent solution. The detection limit (S/N = 3) of 4 x 10(-7) M (13.6 ppb) was achieved by using the 1 x 10(-4) M Fe(III)-Fe(II) buffer containing 0.4 M NaBr, 1.0 M H(2)SO(4) and 0.5% (NH(4))(6)Mo(7)O(24). Analytical throughput was approximately 40 h(-1) and the RSD (n = 6) was 0.6% for measurement of 4 x 10(-6) M hydrogen peroxide. The proposed method was applied to the determination of hydrogen peroxide in real rainwater samples, and was found to provide a good recovery for H(2)O(2) added to rainwater samples.     

Quantitative analysis of manganese, chromium and molybdenum by ion-pair reversed-phase high-performance liquid chromatography with pre-column derivatization and UV-visible detection.

An ion-pair reversed-phase high-performance liquid chromatographic method with UV-visible spectrophotometric detection is proposed for the simultaneous determination of manganese, chromium and molybdenum. By using a C18-bonded silica column, 4-(2-pyridylazo)resorcinol (PAR) chelates of Mn(II), Cr(VI) and Mo(VI) were successfully separated and accurately determined at 480 nm. Tetrabutylammonium bromide (TBAB) was used as the ion-pair reagent. Effects of pH, the buffer system, the concentration of buffer, the color developing time, the concentration of chelating reagent and the ion-pair reagent on the resolution were investigated. PAR chelates were eluted within 20 min at a flow-rate of 1.0 ml min(-1) with a methanol aqueous mobile phase, CH3OH-water (20:80, v/v), containing 1.0 x 10(-3) mol l(-1) acetate buffer (pH 6.5), 1.8 x 10(-2) mol l(-1) TBAB and 2.0 x 10(-4) mol l(-1) PAR. The feasibility of the proposed method was verified with the standard reference materials of nickel-based alloys. The nickel-based alloys were analyzed chromatographically after ammonium pretreatment. Under the optimum conditions, the detection limits for the chelates of Mn(II), Cr(VI) and Mo(VI) were 0.31, 4.2 and 4.6 ng with 100 microl injection, respectively. The accuracy of the proposed chromatographic method was verified by good agreement between the values obtained by this method and certified values.     

Liquid-liquid extraction of molybdenum(VI) and uranium(VI) by LIX 622

The order of extraction of Mo(VI) from 1M acid solutions by 5% (v/v) LIX 622 (HL) in benzene is HCl>HNO₃>HClO₄>H₂SO₄, and extraction decreases with increasing concentration of HCl and H₂SO₄, and increases slightly with increasing concentration of HNO₃ and HClO₄. The extracted species is shown to be MoO₂L₂ as established by IR data of organic extracts and the extracted species in the solid form. Extraction is almost quantitative at and above 10% LIX 622, and is found to be independent of [Mo(VI)] in the range of 10^–4 to 10^–3 M. The diluents CCl₄, CHCl₃ and C₆H₆ are found to be superior to solvents of high dielectric constant for extraction of Mo(VI). Extraction of uranium(VI) by 10% (v/v) LIX 622 in benzene was found to increase with increasing equilibrium pH (3.0 to 6.0), and becomes quantitative at pH 5.9. Tributyl phosphate acts as a modifier up to 2% (v/v). Thorium(IV) is almost not extracted by LIX 622 or its mixture. Separation of Mo(VI) and U(VI) is feasible.     

Spectrophotometric determination of molybdenum in the presence of tungsten using gallein and benzyldodecyldimethylammonium bromide

The chemical similarity between molybdenum and tungsten makes the direct spectrophotometric determination of these metals impossible. Usually the determination is preceded by a separation step. In order to find out a selective and quantitative isolation method, coprecipitation with thioacetamide and Cu(II) as a carrier; MnO₂; cupferron, tannin and crystal violet; quinolin-8-ol, tannin and thioacetamide, were examined. Molybdenum(VI) could be determined in the presence of 100-fold mass excess of tungsten after precipitation with thioacetamide and Cu(II). The remaining methods could only be applied if mass excess of W is equal to or lower with respect to Mo. For the resolution of this problem, the derivative spectrophotometry was used. The studies of different order spectra of gallein complexes of molybdenum, tungsten and their mixtures have shown that the fifth-derivative spectra allows one to eliminate the interfering effects of W on the determination of Mo. At 650 nm the spectral features of tungsten is zeroing while the value of the fifth-derivative spectrum of mixture of Mo and W corresponds only to the concentration of molybdenum in the examined solution. Beer’s law is obeyed in the range 0.32–0.80 μg/mL of Mo. The developed derivative spectrophotometric method and the most selective pre-separation method, based on the precipitation of molybdenum(VI) sulphide, were applied to the determination of Mo in Armco iron and steel. The accuracy of the elaborated methods was confirmed by comparison of the determined content of Mo with certified values as well as with the result obtained by the reference ICP-OES technique.     

Simultaneous spectrophotometric determination of phosphate and silicate by using principal component artificial neural network

A very sensitive, simple and selective spectrophotometric method for simultaneous determination of phosphate and silicate based on formation of phospho- and silicomolybdenum blue complexes in the presence of ascorbic acid is described. Although the complexes of phosphate and silicate with reagent in the presence of ascorbic acid show a spectral overlap, they have been simultaneously determined by principal component artificial neural network (PC-ANN). The PC-ANN architectures were different for phosphate and silicate. The output of phosphate PC-ANN architecture was used as an input for silicate PC-ANN architecture. This modification improves the capability of silicate PC-ANN model for prediction of silicate concentrations. The linear range was 0.01-3.00 microg mL(-1) for phosphate and 0.01-5.00 microg mL(-1) for silicate. Interference effects of common anions and cations were studied and the proposed method was also applied satisfactorily to the determination of phosphate and silicate in detergents.