Fe2O3对CaO-Al2O3-MgO-SiO2系微晶玻璃析晶及断裂特性的影响

采用熔融法,利用纯化学试剂制备了CaO-A12O3-MgO-SiO2 (CAMS)系微晶玻璃,利用DTA、XRD、拉曼光谱仪等研究了Fe2O3对微晶玻璃析晶特性的影响规律,微晶玻璃的物化性能由抗折强度、杨氏模量、剪切模量、泊松比、维氏硬度等进行评价.结果表明,微晶玻璃的析晶特性随着Fe2 O3含量的增加而增强,对应母体玻璃中首先出现富铁相,进而促进辉石主晶相的析出.微晶玻璃的断裂特性及裂纹扩展方式均随析晶度的提高得到明显改善.但过量的Fe2O3添加则对微晶玻璃的析晶特性无明显影响,反而降低了玻璃相的致密性.微晶玻璃的耐酸性、抗折强度、杨氏模量及剪切模量均呈现先增加后降低的趋势,微晶玻璃的Fe2 O3含量为6.6wt;时综合性能最优.     

晶核剂P2O5对CaO-Al2O3-SiO2系黄磷炉渣微晶玻璃析晶的影响

采用熔融法以自然冷却黄磷炉渣为主要原料,P2O5为晶核剂,制备了黄磷炉渣微晶玻璃.利用X射线衍射仪(XRD)、差热分析(DTA)和扫描电子显微镜(SEM)等分析技术手段,探究了晶核剂P2O5(以KH2PO4的形式引入)对黄磷炉渣微晶玻璃晶化行为及物化性能的影响规律.结果表明:黄磷炉渣基础玻璃的析晶峰温度Tp及析晶活化能E随着P2O5晶核剂的增加呈现先减小后增大的趋势;当晶核剂P2O5加入量达到4wt;时,黄磷炉渣基础玻璃的析晶峰温度Tp及析晶活化能E最小,析晶效果最优,物化性能最优;主晶相硅灰石(CaSiO3)并不随着晶核剂P2O5加入量的增大而发生改变,同时能够促进晶相氟磷灰石(Ca5(PQ)3F)生成.     

CaO-MgO-Al2O3-SiO2-P2O5-(F)微晶玻璃的析晶及特征

采用熔融法制备了不同P2O5及F含量的CaO-MgO-Al2O3-SiO2-P2O5-(F)基础玻璃试样,研究了CaO-MgO- Al2O3-SiO2-P2O5-(F)系微晶玻璃的析晶及特征.结果表明:在CaO-MgO-Al2O3-SiO2-8.0wt;P2O5玻璃中,表面析晶和内部析晶同时存在,析出晶体主要为钙长石(CaAl2Si2O8)相、硅灰石(CaSiO3)和α-磷酸钙(Ca3(PO4)2).玻璃中P2O5含量的提高抑制玻璃的表面析晶,同时促进了玻璃的整体析晶和α-磷酸钙晶体析出.同时添加P2O5和F的玻璃试样以整体析晶为主,析出晶体为块状氟磷灰石和粒状钙长石相.     

Cr2O3对白云鄂博西尾矿微晶玻璃显微结构及性能的影响

以白云鄂博西尾矿和粉煤灰为主要原料,采用熔融法制备了添加0～2.0wt; Cr2O3的CaO-MgO-SiO2-Al2O3系微晶玻璃,利用DTA、XRD、FESEM、EDS和综合力学性能仪等测试手段,研究了Cr2O3含量对该体系微晶玻璃显微结构及性能的影响.实验结果表明:少量Cr2O3 (0.5wt;)可有效降低样品的晶化温度,促进主晶相辉石相(Ca(Mg,Fe,Al) (Si,Al)2O6)的形成,同时细化其显微组织,从而提高样品的密度、抗折强度和耐酸碱性;当Cr2O3含量大于等于1.5wt;时,析晶峰温度由804℃提高到816℃,同时微晶玻璃中形成不规则块状结构的镁铁铬尖晶石(MgFeo.9 Cr1.1O4)第二相,并进而引起周围辉石相晶粒异常长大,降低其抗折强度.     

CaO对MgO-Al2O3-SiO2系微晶玻璃结构与性能的影响

以化学纯试剂为原料,采用熔融法制备MgO-Al2O3-SiO2(MAS)系微晶玻璃.利用DSC、XRD、SEM等及理化性能测试手段研究了不同CaO含量对微晶玻璃析晶行为、物相组成、显微结构及理化性能的影响.结果表明:一定含量的CaO可以降低析晶活化能,促进玻璃析晶;随CaO含量的增加,微晶玻璃主晶相由假蓝宝石向α-堇青石转变,晶体形貌由棒状晶转变为枝状晶,晶粒尺寸呈先减后增的趋势;当CaO含量为3wt;时微晶玻璃热膨胀系数和相对介电常数(εr)达到最低,分别为3.89×10-1℃-1和10.09(1 MHz);当不外添CaO时微晶玻璃Vickers硬度达到最大,为10.52 GPa.     

P2O5对CaO-MgO-Al2O3-SiO2系微晶玻璃析晶的影响

采用熔融法制备了不同P2O5含量的CaO-MgO-Al2O3-SiO2玻璃样品,研究了P2O5对该系微晶玻璃析晶的影响规律.结果表明:在所研究的CaO-MgO-Al2O3-SiO2玻璃中,P2O5的最大溶解量在10.0;质量分数左右,超过其饱和溶解度后将析出α-磷酸钙相.玻璃中添加4.0;质量分数P2O5时以表面析晶为主,析出晶体为钙长石和少量硅灰石.随着P2O5含量的提高, α-磷酸钙逐渐析出,同时钙长石和硅灰石的析出逐渐降低.进一步提高P2O5含量抑制了玻璃的表面析晶,促进了玻璃的分相和整体析晶.当P2O5的含量达到10;时,玻璃以整体析晶为主,在分相区内外区域析出晶体的形态非常相似,均呈现为细小粒状.     

Fe2O3掺杂对MgO-Al2O3-SiO2系玻璃析晶和性能的影响

采用高温熔融法和两步法微晶热处理制备了MgO-Al2O3-SiO2系堇青石微晶玻璃和铁尖晶石微晶玻璃.利用DSC分析、X射线衍射、FTIR和扫描电子显微镜等手段研究了Fe2O3对玻璃的析晶性能、显微结构和物理性能的影响.结果表明,Fe2 O3的加入可有效降低析晶活化能,促进晶体的析出.当Fe2O3含量达到7.44;时,主晶相由堇青石变为铁尖晶石.Fe2O3掺杂使样品的介电常数由3.2增大至5.8、热膨胀系数由1.941× 10-7增大至7.74×10-6、维氏硬度由7.131GPa增大至11.655 GPa,同时介电损耗由0.05降低至0.015.     

TiO2对自然冷却黄磷炉渣微晶玻璃析晶行为的影响

以自然冷却黄磷炉渣为主要原料,采用熔融法制备CaO-Al2O3-SiO2系微晶玻璃,并借助DTA、XRD、SEM等分析了TiO2作为晶核剂对微晶玻璃析晶及其性能的影响规律.利用修正后的Johnson-Mehl-Avrami(JMA)方程初步计算微晶玻璃样品的析晶活化能E及晶体生长指数n.结果表明:自然冷却黄磷炉渣中固有的晶核剂可有效的促进CaO-Al2O3-SiO2系统的析晶,炉渣固有的TiO2可促进大量晶核的形成,晶化指数达到4.84,随着TiO2的加入,系统的析晶活化能由126.1483 kJ/mol增加到363.8206 kJ/mol,而晶化指数变为3.24.晶化机制由体积析晶变为二维析晶.主晶相的种类没有随TiO2量的增加而改变,均为硅灰石(CaSiO3)和钙铁辉石((Ca,Fe) SiO3).     

Nd3+∶ZnO-B2O3-Al2O3-SiO2系透明玻璃陶瓷的制备及表征

制备了Nd3+∶ZnO-B2O3-Al2O3-SiO2系透明玻璃陶瓷.运用差热分析(DTA)、X射线衍射(XRD)、扫描电镜(SEM)、NV-Vis-Nir(紫外可见近红外分光光度计)、傅里叶变换荧光光谱等测试方法,研究了晶核剂的含量对Nd3∶ZnO-B2O3-Al2O3-SiO2系透明玻璃陶瓷的核化和晶化性能的影响.利用修正的Kissinger方程研究了晶核剂对玻璃析晶动力学参数,析晶活化能E和析晶动力学判据k(Tp),利用Augis-Bennett方程计算出Avrami参数n.并分析其显微形貌同光透过率的关系,对光学性能进行了研究.     

不同冷却方式黄磷炉渣微晶玻璃析晶动力学研究

以水淬黄磷炉渣和自然冷却态黄磷炉渣为研究对象,采用熔融法制备CaO-Al2O3-SiO2系微晶玻璃.通过差热分析、X射线衍射和扫描电镜,并利用修正后的Johnson-Mehl-Avrami (JMA)方程和Augis-Bennett方程,分析了不同冷却方式下黄磷炉渣制备微晶玻璃的析晶规律.结果表明:不同冷却方式对微晶玻璃的析晶行为有所不同,水淬黄磷炉渣微晶玻璃的析晶活化能E为352.609 kJ/mol,自然冷却黄磷炉渣微晶玻璃的析晶活化能E为405.685kJ/mol;两种不同冷却方式的黄磷炉渣微晶玻璃的晶化机制均为三维体积晶化.水淬黄磷炉渣微晶玻璃中主晶相为硅灰石(CaSiO3)并含有少量的石英矿物;自然冷却黄磷炉渣微晶玻璃中主晶相为钙蔷薇辉石类(Ca(Mn2,Ca)Si2O6)和含铁硅灰石类固溶体((Ca,Fe) SiO3).以自然冷却渣制备的微晶玻璃性能优于水淬渣制备出的微晶玻璃.     

CaO-MgO-Al2O3-Fe2O3-B2O3-SiO2系微晶釉的制备

通过引入B2O3以降低烧成温度,利用赤泥中的Fe2O3为着色剂,在1150℃左右低温烧成制备了CaO-MgO-Al2O3-Fe2O3-B2O3-SiO2系微晶釉.赤泥的加入量为20;左右时,釉面具有良好的装饰效果和显微硬度.利用XRD、SEM研究了釉的物相及显微组织.结果表明,釉中析出的微晶是普通辉石,微晶的含量随MgO及CaO的含量增加而增加,而提高Al2O3含量则抑制微晶的析出.     

Fe2O3-CO3O4共掺杂MgO-Al2O3-SiO2体系的红外辐射性能研究

采用固相反应法制备Fe2O3-Co3O4共掺杂MgO-Al2O3-SiO2体系的复合陶瓷材料,并通过XRD、SEM、XPS以及红外辐射测试等方法研究了样品的结晶行为与红外辐射性能.结果表明:Fe2 O3和Co3 O4共掺杂MgO-Al2 O3-SiO2体系后离子分布改变并生成混合尖晶石,从而引起品格畸变,从而有效提高材料的红外辐射性能.材料的红外发射率与其晶格畸变程度具有相同的变化趋势,并随Fe2 O3与Co3O4质量之比(R)的增加呈非线性变化.当R=3∶2时,材料在8 ～ 14 μm波段的辐射率可达0.92.     

EPR and magnetic susceptibility studies of B2O3–Bi2O3–Gd2O3 glasses

Glasses of the xGd₂O₃ · (100 − x)[B₂O₃ · Bi₂O₃] system with 0.5 ⩽ x ⩽ 10 mol% were studied by electron paramagnetic resonance (EPR) and magnetic susceptibility measurements. Data obtained show that for low gadolinium oxide contents of the samples (x ⩽ 3 mol%) the Gd³⁺ ions are randomly distributed in the host glass matrix and are present as isolated and dipole–dipole coupled species. For higher gadolinium oxide contents of the samples (x > 3 mol%) the Gd³⁺ ions appear as both isolated and antiferromagnetically coupled species. The EPR spectra of the glasses reveal resonance sites with an unexpected high crystalline field in addition to the ‘U’ spectrum, typical for Gd³⁺ ions in disordered systems. This absorption line is due to Gd³⁺ ions that replace Bi³⁺ ions from the host glass matrix and could play the network unconventional former role in the studied glasses.     

Yb2O3-Y2O3-Gd2O3-ZrO2热障涂层制备及性能研究

以Yb2O3、Y2O3 、Gd2O3稀土氧化物粉末和ZrOCl2·8H2O粉末为原料,采用化学共沉淀法制备了Yb2O3-Y2O3-Gd2O3-ZrO2 (YYGZO)热喷涂用粉末,采用大气等离子喷涂技术制备了YYGZO涂层,利用场发射扫描电镜(FESEM)、X射线衍射(XRD)研究了YYGZO粉末及涂层的微观组织形貌、相结构.结果表明,制备的热喷涂YYGZO粉末大部分呈规则实心球体状,且球形度良好,颗粒粒径均匀,大部分颗粒粒径分布为30～60μm,流动性能较好,满足大气等离子喷涂的要求.YYGZO涂层具有较好的高温相结构稳定性.所制备YYGZO热障涂层组织结构比较致密,涂层各个界面结合紧密,孔隙率约为9.23;,结合强度为35.2 MPa.     

Thermal expansion and transition temperature of glasses in the systems BeO–Al2O3–B2O3 and MgO–Al2O3–B2O3

Researches were conducted for glasses in the systems BeO–Al₂O₃–B₂O₃ and MgO–Al₂O₃–B₂O. The following characteristics have been determined: thermal expansion coefficient within 20–300 °C, structural thermal expansion coefficient (STEC) and glass transition temperature. The discussed properties of Be-aluminoborate and Mg-aluminoborate glasses have been compared with those of Ca-, Sr- and Ba-aluminoborate glasses. TEC of studied glasses gets higher going from Be-aluminoborate glasses to Ba-aluminoborate ones, but T_g decreases under the same succession. The dependence of STEC on the nature of a given cation is more complicated. The pattern of dependence of the properties on composition is due to changing the boron coordination number with respect to oxygen, which is the main network-former, and to competition between the aluminium and boron for the oxygen brought by an ion-modifier. The difference between the effect of one ion-modifier and that of another is determined by decreasing the radius of an ion and increasing its electric field strength in the succession from Ba²⁺ to Be²⁺. The ions of Be and Mg can also act as network-former to some extent.     

Structural properties of Cr2O3–Fe2O3–P2O5 glasses,Part I

The structural properties of xCr₂O₃–(40 − x)Fe₂O₃–60P₂O₅, 0 ⩽ x ⩽ 10 (mol%) glasses have been investigated by Raman and Mössbauer spectroscopies, X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The Raman spectra show that the addition of up to 5.3 mol% Cr₂O₃ does not produce any changes in the glass structure, which consists predominantly of pyrophosphate, Q¹, units. This is in accordance with O/P ≈ 3.5 for these glasses. The increase in glass density and T_g that occurs with increasing Cr₂O₃ suggests the strengthening of glass network. The Mössbauer spectra indicate that the Fe²⁺/Fe_tot ratio increases from 0.13 to 0.28 with increasing Cr₂O₃ content up to 5.3 mol%, which can be related to an increase in the melting temperature from 1423 to 1473 K. After annealing, the 10Cr₂O₃–30Fe₂O₃–60P₂O₅ (mol%) sample was partially crystallized and contained crystalline β-CrPO₄ and Fe₃(P₂O₇)₂. The SEM and AFM micrographs of the partially crystallized sample revealed randomly distributed crystals embedded in a homogeneous glass matrix. EDS analysis indicated that the glass matrix was rich in Fe₂O₃ (39.6 mol%) and P₂O₅ (54.9 mol%), but contained only 5.5 mol% of Cr₂O₃. These results suggest that the maximum solubility of chromium in these iron phosphate melts is 5.5 mol% Cr₂O₃.     

BaTiO3-Nb2O5-Fe2O3陶瓷介电性能的研究

利用传统方法制备了BaTiO3-Nb2O5-Fe2O3(BTNF)陶瓷,采用X射线衍射仪、电容测试仪、电滞回线测量仪等测试手段研究了不同添加剂(Fe2O3、Co2O3、Nb2O5)对陶瓷晶体结构、介电性能及铁电性的影响.结果表明:Nb2O5是施主掺杂,易引起晶格畸变,使四方率增大;而Fe2O3为受主掺杂,其可提高氧空位浓度,促进BaTiO3陶瓷晶粒生长.同时掺杂Fe2O3、Nb2O5时,可以相互补偿.当Fe2O3浓度约为0.15;摩尔分数,Nb2O5浓度为0.79;摩尔分数时,陶瓷的介电常数达到4443,温度特性≤±10;,可以满足Y5P瓷料的要求.     

R2O-RO-SiO2-Al2O3-Fe2O3-P2O5系分相釉的研究

针对铁红分相釉的配方特点,采用L8(4 ×24)正交实验研究了钠长石、牛骨灰、滑石、方解石、石英加入量对R2O-RO-SiO2-Al2O3-Fe2O3-P2O5系统分相釉釉面效果的影响,采用扫描电子显微镜(SEM)和能谱分析(EDS)对釉层的微观结构进行了表征.研究发现:牛骨灰对釉面是否出现“柿红”效果影响最显著,而方解石影响最不明显.Si/P摩尔比对铁红色釉面的产生起关键作用,当Si/P摩尔比小于2O,出现铁红釉面效果的概率极高.随着滑石加入量从9份变化到18份,出现铁红色釉面的趋势反而降低.经SEM和EDS分析发现,“柿红色”、“酒红色”釉面效果的产生很大程度上是由于釉层液液分相促进Fe2O3富集或偏析造成,且特别容易在高钠、低镁、低铝处聚集,最终连成雪花状结晶.     

Semi-quantitative analysis for FTIR spectra of Al2O3-PbO-B2O3-SiO2 glasses

A series of glass of the molar formula xAl₂O₃-(50-x)PbO-25B₂O₃-25SiO₂ with x:2.5–17.5 with step of 2.5 mol.% was prepared and measured for, density, molar volume and infrared absorption. A semiquantitative analysis of the IR spectra was performed. It was found that each oxide would contribute in density with a specific factor. The density factor related to PbO is markedly higher than that of the other two oxides represent the glass skeleton which means that the content of PbO is the main factor affecting the density. The depolymerization of the whole glass skeleton increases with increasing the content of Al₂O₃. There is a competition between the role of PbO and Al₂O₃ in changing the value of N₄ and the crosslinking of the glass network. The silicate network tends to be distinguished from the reminder of the whole glass network with increasing alumina. The IR band located near 700 cm^? 1 was suggested to be due to the vibrations of bridging oxygens between trigonal boron atoms. An essential change in the role of PbO in these glasses from glass modifier to glass former occurred around 12 mol.% Al₂O₃.     

In2O3 and tin-doped In2O3 nanocrystals prepared by glass crystallization

Glasses in the system Na₂O/B₂O₃/Al₂O₃/In₂O₃/(SnO₂) were melted and subsequently tempered in the range from 540 to 700 °C. This led to the crystallization of In₂O₃, besides also NaBO₂ and Na₂Al₂B₂O₇ were formed. The crystallite sizes were in the range from 12 to 34 nm, depending on the temperature of thermal treatment, as calculated from XRD-line broadening. Crystal sizes determined by TEM were in the same range. Particle size histograms show a narrow crystal size distribution. After crystallization, the glass matrices and the non indium-containing crystalline phases were dissolved in diluted acetic acid. Spectra of the obtained suspensions containing tin-doped In₂O₃ nanocrystals exhibited a sharp UV-cut off, high transmission in the visible range and strongly decreasing transmission at wavelengths >1000 nm.