Asymmetrically Apodized Linearly Chirped Fiber Bragg Gratings for Efficient Pulse Compression

Asymmetrically apodized linearly chirped fiber Bragg gratings (FBGs) are shown to have highly linearized time-delay response. In simulations of a five-stage, 5-cm grating-based dispersion compensation system, asymmetrically apodized FBGs are shown to give over 60% reduction in the energy scattered from the main pulse body, 16 ps?60 ps pulses propagated over 800 km, as compared to a symmetrically apodized grating of similar length, strength, and bandwidth.     

Electro-optical sampling non-synchronous delay scanning measurement of electron beam bunch length at BFEL

The Electro-optical sampling delay scanning technique can be used for electron beam bunch length measurement.A novel non-synchronous delay scanning technique based on the electro-optical sampling measurements is presented.Based on Beijing Free Electron Laser(BFEL),the electron beam bunch length was measured with the electro-optical sampling technique for the first time in China.The result shows that the electron beam bunch length at BFEL is about 5.6±1.2 ps.     

High-Accuracy Measurement of the Dispersion of Chirped Fiber Gratings

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｆｉｂｅｒｇｒａｔｉｎｇｓａｒｅｐｒｏｖｅｄｔｏｂｅｏｎｅｏｆｔｈｅｍｏｓｔｉｍｐｏｒｔａｎｔｒｅｃｅｎｔｄｅｖｅｌｏｐｍｅｎｔｓｉｎｔｈｅｆｉｅｌｄｏｆｏｐｔｉｃａｌｆｉｂｅｒｔｅｌｅｃｏｍｍｕｎｉｃａｔｉｏｎｓａｎｄｓｅｎｓｉｎｇ .Ｔｈｅｙａｒｅｌｉｋｅｌｙｔｏｈａｖｅａｐｐｌｉｃａｔｉｏｎｉｎｔｗｏｍａｉｎａｒｅａｓ:ｄｉｓｐｅｒｓｉｏｎｃｏｍｐｅｎｓａｔｉｏｎｉｎｌｏｎｇ ｈａｕｌｆｉｂｅｒｎｅｔｗｏｒｋｓ[1,2 ]ａｎｄｗａｖｅｌｅｎｇｔｈｒｏｕｔｉｎｇｉｎｗ…     

弱双折射光纤布喇格光栅反射偏振对温度响应特性的研究

理论分析了切趾弱双折射光纤布喇格光栅反射偏振相关特性与温度之间的关系.数值模拟了切趾弱双折射光纤光栅的反射谱、偏振相关损耗和差分群时延随波长变化曲线.实验测出了不同温度下反射谱、偏振相关损耗和差分群时延随波长变化曲线.根据实验结果对偏振相关损耗和差分群时延的变化情况作出了分析.反射偏振相关损耗呈现两个峰值,随温度增加两峰漂移程度相同,表明偏振相关损耗无明显差异.差分群时延最大值随温度增加成线性向长波方向漂移,证明了光纤光栅正交模损耗变化的等同性.综合理论分析与实验结果表明:切趾弱双折射光纤布喇格光栅的偏振特性随温度产生明显的变化,其正交模变化呈现等比例特性.     

Optical True Time Delay for Phased Array Antennas Composed of 2×2 Optical MEMS Switches and Fiber Delay Lines

We proposed an optical true time delay (TTD) for phased array antennas (PAAs) composed of 2×2 optical MEMS switches, single-mode fiber delay lines, and a fixed wavelength laser diode. A 3-bit TTD for 10 GHz PAAs was implemented with a time delay error less than ± 0.2 ps.     

Frequency Downconverting Fiber Grating-Based Beamformers for High-Capacity Phased Arrays

A technique is presented to remove the beat noise limitation in multibeam beam formers using a simple all-optical microwave frequency downconversion technique prior to performing the true-time delay equalization in the optical domain. The frequency conversion concept enables a significant increase in beam-number capac ity to be achieved due to the elimination of beat noise limits, and also effectively removes the power penalty due to chromatic dispersion limitations of the chirped grating units in the beamformer. The Bragg grating requirements for the frequency converting beamforming network are analyzed and show that tanh-profile apodized gratings can meet the isolation, reflectivity, and narrow bandwidth requirements. For an X-band phased array, more than a twofold increase in beam capacity is shown through the use of the frequency conversion technique with the grating-based beamformer, and the resulting beamformer has the minimum number of optical interconnects with true-time delay operation.     

Frequency Downconverting Fiber Grating-Based Beamformers for High-Capacity Phased Arrays

A technique is presented to remove the beat noise limitation in multibeam beam formers using a simple all-optical microwave frequency downconversion technique prior to performing the true-time delay equalization in the optical domain. The frequency conversion concept enables a significant increase in beam-number capac ity to be achieved due to the elimination of beat noise limits, and also effectively removes the power penalty due to chromatic dispersion limitations of the chirped grating units in the beamformer. The Bragg grating requirements for the frequency converting beamforming network are analyzed and show that tanh-profile apodized gratings can meet the isolation, reflectivity, and narrow bandwidth requirements. For an X-band phased array, more than a twofold increase in beam capacity is shown through the use of the frequency conversion technique with the grating-based beamformer, and the resulting beamformer has the minimum number of optical interconnects with true-time delay operation.     

一种用于电光开关的高速、高压电脉冲的产生

介绍了一种用于电光开关驱动源的高压超快电脉冲产生技术;电路采用级联的雪崩晶体管串和微波传输线结构,输出阻抗50Ω;在50Ω负载情况下,获得脉冲下降时间为1ns、幅度达到5kV、峰值电压为6.4 kV、幅度和半宽度稳定性优于2％、触发晃动为±15ps、触发延时为30 ns,脉冲峰值电流为128 A的高压高速大电流脉冲.     

基于1085 km实地光纤链路的双波长光纤时间同步研究

在长距离高精度光纤时间同步系统中,为了减少后向反射光与光纤色散对传输精度的影响,本文在双波长光纤时间同步传输方法之上,提出了一种具有色散误差修正功能的双波长光纤时间同步传输方法.以自行研制的工程样机在长度约为800 km的实验室光纤链路上和1085 km的实地光纤链路上进行了实验测试,也是国内首次实现千公里级实地光纤时间同步传输.在实验室光纤链路上,测得传输链路色散补偿后的色散时延误差为10 ps,时间同步标准差为5.7 ps,稳定度为1.12 ps@105 s,不确定度为18.4 ps.在实地光纤链路上,测得传输链路色散补偿后的色散时延误差为60 ps,时间同步标准差为18 ps,稳定度为5.4 ps@4×10⁴ s,不确定度为63.5 ps.     

Zernike apodized photon sieves for high-resolution phase-contrast x-ray microscopy

We present a type of diffractive lens, Zernike apodized photon sieves (ZAPS), used as the objective for high spatial resolution and high phase-contrast imaging of weakly absorbing materials in x rays. The structure of ZAPS is based on the combination of two concepts: apodized photon sieves and Zernike phase contrast. The ZAPS is a single optic that integrates the appropriate ±π/2 rad phase shift through selective zone placement shifts in an apodized photon sieve. Analysis of the focusing properties of the apodized photon sieve in terms of point-spread function show that the sidelobes have been significantly suppressed at the expense of slightly widening the width of the main lobe. In combination with synchrotron light sources, ZAPS offers new opportunities for high-resolution phase-contrast x-ray microscopy in the physical and life sciences.     

40Gb/s光时分复用传输光纤光栅补偿色散研究

用精密扫描掩模法写入宽阻带啁啾光纤光栅,掩模板背面两端各10％长度处镀有按4阶高斯函数透过率的膜,写入的啁啾光栅的时延纹波最大值为20ps。为减少写入光纤光栅的偏振模色散,研制了新的低偏振模色散光纤光栅补偿写入法。采用补偿写入法前的平均微分群时延为9．1406 ps;采用补偿写入法后的平均微分群时延为0．1521 ps。并利用低偏振模色散光纤光栅对40Gb／s光时分复用系统在普通G．652光纤传输122km的色散进行了补偿实验,功率代价为1．5dB。     

啁啾双光纤光栅群时延特性

研究了变迹线性啁啾双光纤光栅的群时延特性及其在高次色散补偿中的应用.分析表明,群时延特性与周期差ΔΛ和不同的啁啾参量C有很大的关系.研究结果表明啁啾双光纤光栅在高次色散补偿和光纤CDMA中有应用价值.     

Thermally tuned optical fiber for true time delay generation

A new technique for generating a continuous range of true time delay values is introduced. Heating optical fiber in order to change the effective index of the guided mode produces time delays. A 45-m section of single-mode silica fiber is demonstrated to produce a continuous range of time delay values from 0 to 211 ps over a temperature tuning range of 50°C (30–80°C). A thermal time delay factor is introduced and found to be 0.096 ps/m°C for Corning LEAF fiber. A 7.66-m section of multimode Lucina polymer fiber is demonstrated to produce a range of time delay values from 0 to 32 ps over a temperature tuning range of 30°C (30–60°C). The thermal time delay factor for this fiber is −0.1427 ps/m°C.     

X射线相衬成像光子筛

基于 Zernike相衬成像原理和光瞳切趾原理,提出一种将相位板和切趾光子筛集成为一个相衬显微物镜的 X射线相衬成像光子筛的设计方法.这种 X射线相衬成像物镜可以实现生物体组织或者其他弱吸收材料的高分辨率和高衬度成像.通过优化光子筛透镜的衍射结构,可以抑制成像系统的点扩展函数的旁瓣和消除高阶衍射焦点,从而提高成像分辨率;另外,将光子筛透镜和变相板合为一体,克服了成像透镜和变相板难以对准的缺陷.以高斯切趾光子筛为例,实验验证了设计方法的可行性. 关键词： X射线显微技术 相衬成像 光瞳切趾 光子筛     

Chromatic dispersion measurements using a virtually referenced interferometer

We present a technique for measuring the chromatic dispersion of short-length (<1 m) optical devices using unbalanced spectral interferometry and a virtual reference path. The technique combines the speed and ease of measurement of unbalanced spectral interferometry with the accuracy of balanced spectral interferometry. We demonstrate measurement accuracy for group delay and the dispersion-length product of ~10(-3) ps/m (<0.0001% relative error) and ~10(-5) ps/m (<0.5% relative error), respectively. Measurement precision is demonstrated to be ~10(-5) ps/m (<0.15% relative deviation). We validate the technique via measurement of well-known dispersion standards.     

Apodized chirped fibre Bragg gratings for dispersion compensation in a 10 Gbit/s IM-DD semiconductor laser system

Different fibre Bragg grating dispersion compensation schemes are studied for a directly modulated 1550 nm single-mode semiconductor laser signal through a standard nonlinear fibre link. The laser diode is simulated by its stochastic rate equations, while the nonlinear Schrödinger equation is used to simulate the propagation. The optimum length for dispersion compensation after transmission through 100 km SSM fibre is studied. Pulses with a FWHM of the order of 65 ps with any linewidth-enhancement factor are reconstructed using pre-compensation or post-compensation with an apodized 5.75 cm chirped fibre Bragg grating.     

多路激光装置同步技术研究

 多路激光装置同步系统包括精密同步机和数字同步机两种单元技术,它们具有四路延时脉冲（A、B、C、D）和一路标准时钟脉冲（T₀）输出,精密同步机延时同步精度为10ps, 最大触发晃动小于10ps,延时范围200ns;数字同步机：延时同步精度为5ps, 最大触发晃动小于200ps,延时范围10ms。     

Time-domain Fourier optics for polarization-mode dispersion compensation

We report on a novel technique to compensate for all-order polarization-mode dispersion. By means of this technique, based on a suitable combination of phase modulation and group-velocity dispersion, we compensated for as much as 60 ps of differential group delay that affected a 10-Gbit/s return-to-zero data stream.     

Energy conversion process from the photoexcited electronic states studied by the temperature lens and acoustic peak delay methods in solution

Ultrafast temperature rise after the deactivation of the electronically excited state of 2-hydroxybenzophenone in various solvents is investigated by two photothermal techniques; temperature lens and acoustic peak delay methods, and by the population grating technique. The results from these methods show that the thermalization process takes place by two phases; fast (<1 ps) and rather slow (30 ps) processes. From the solvent dependence of the thermalization rate, we suggest that these processes are related with the intermolecular interaction and the solvation structure around the photoexcited molecules.     

Optical monitoring of PMD accumulation on a Pol-MUX phase-modulated signal using degree-of-polarization measurements

We experimentally demonstrate a chromatic dispersion insensitive monitoring technique for monitoring of polarization mode dispersion and time misalignment in a 80 Gbit/s polarization-multiplexed return-to-zero differential phase-shift-keying (Pol-MUX RZ-DPSK) signal using a polarimeter and degree-of polarization (DOP) measurements. This technique is modulation format independent (i.e., applicable to both the phase- and amplitude-modulated data) and capable of measuring the fast change of polarization effects caused by vibration or other fast disturbances in the fiber link. We show that the monitored DOP of this signal decreases by 10.8% with differential group delay of 0-12 ps and decreases by 20% with a maximum misalignment of 12.5 ps between two orthogonally polarized RZ-DPSK channels. These measurements are less sensitive to chromatic dispersion of 0-400 ps/nm.