Measurements of actinide nuclides in water samples from the primary circuit of a nuclear power plant

Weekly, consecutive primary coolant samples from a boiling water reactor have been analyzed for^{239, 240}Pu,²³⁸Pu+²⁴¹Am,²⁴²Cm and²⁴⁴Cm for about two years, and for²³⁸Pu,²⁴¹Pu and²⁴¹Am for one year. Concentration ranges are reported. Samples were prepared for counting either directly by evaporation or by chemical separation on BioRad AG 1×4 resin and subsequent electrolysis, and were counted in 20 cm dia Frish grid ionization chambers. Procedures are described. For most actinide nuclides, activity ratios in primary coolant were found to be different from those in worldwide fallout, thus allowing an identification of origin in the case, that actinides should be detected in the vicinity of a nuclear power station.     

Pre-concentration of actinide elements from soils and large volume water samples using extraction chromatography

The analysis of environmental samples for low levels of U, Pu, Am and other actinide elements is often hampered by sample-dependent problems involving the composition and/or mineralogy of specific samples. While relatively small samples (1–2 g of soil or 1–2 of water) are required to reach the extremely low detection limits occasionally mandated for environmental monitoring. One approach to avoid the troublesome and often inexplicable problems collectively referred to as matrix effects is to pre-concentrate actinides into a common form that would then behave uniformly and predictably during a subsequent separation scheme. Recently, a new extraction chromatographic resin based on diphosphonate chemistry was developed at Argonne National Laboratory. This resin commercialized as Eichrom's Actinide Resin, exhibits extremely high affinity for actinide elements even in the presence of high concentrations of salts. We have measured the uptake of actinides by the Dipex^® extractant from natural waters and natural matrix soil standards. Water samples have been analyzed for gross -activities and gave results that compared favorably to the traditional approach. In addition, we have obtained good recoveries and excellent separations for soil samples as judged by resolution on the -spectra and the complete absence of interfering energies.     

Determination of fission nuclides in rain water by X-ray spectrometry

Greatly elevated levels of certain radioactive fission products were found in rain water collected in southern France 8 days after a Chinese nuclear weapon test in October 1980. The amount of radiation present was not high and its measurement was not easy. A new method for measuring low level environmental radioactivity has been devised.     

Radiochemical determination of the yields of transuranium nuclides produced from natural uranium irradiated in a reactor

Transuranium nuclides were produced by irradiating a pellet of natural uranium sulfide in the Japan Material Testing Reactor (JMTR). After irradiation, a successive separation of uranium, plutonium, americium and curium was carried out. The fractional concentrations of the nuclides²³⁸Pu,²³⁹Pu,²⁴⁰Pu,²⁴¹Am,²⁴³Am,²⁴²Cm and²⁴⁴Cm were determined by α-ray spectrometry, and those of²⁴¹Pu and^242mAm were estimated from the build-up of α-emitting daughters,²⁴¹Am and²⁴²Cm, respectively. As the yield of²⁴²Pu was too slight to be detected by α-counting, the neutron activation analysis of the plutonium fraction based on the²⁴²Pu(n, γ)²⁴³Pu reaction was carried out by γ-ray spectrometry, and it was shown that a few pg of²⁴²Pu could be determined. A burn-up of²³⁵U was also estimated by neutron activation analysis. The experimental results are compared with the calculated ones.     

Determination of environmental actinide nuclides and210Pb(210Po) by low-energy photon spectrometry with alpha-spectrometry

Low-energy photon spectrometry with -spectrometry was used to determine the environmental concentrations of low-level actinides and other nuclides, especially²¹⁰Pb and²¹⁰Po. The isotopic ratio of²⁴⁰Pu/²³⁹Pu was successfully determined by measuring L_x-ray/-ray counting ratio. A reliable method has been developed for the determination of extremely low-level²³⁷Np global fallout in environmental samples. The non-destructive determination by Ge-LEPS for natural²¹⁰Pb in various samples (tobacco leaves, commercially available tobacco, etc.) was also carried out with the determination of²¹⁰Po by -spectrometry using²⁰⁹Po as a yield tracer.     

Determination of trihalomethanes in water samples: a review

This article reviews the most recent literature addressing the analytical methods applied for trihalomethanes (THMs) determination in water samples. This analysis is usually performed with gas chromatography (GC) combined with a preconcentration step. The detectors most widely used in this type of analyses are mass spectrometers (MS) and electron capture detectors (ECD). Here, we review the analytical characteristics, the time required for analysis, and the simplicity of the optimised methods. The main difference between these methods lies in the sample pretreatment step; therefore, special emphasis is placed on this aspect. The techniques covered are direct aqueous injection (DAI), liquid-liquid extraction (LLE), headspace (HS), and membrane-based techniques. We also review the main chromatographic columns employed and consider novel aspects of chromatographic analysis, such as the use of fast gas chromatography (FGC). Concerning the detection step, besides the common techniques, the use of uncommon detectors such as fluorescence detector, pulsed discharge photoionization detector (PDPID), dry electrolytic conductivity detector (DELCD), atomic emission detector (AED) and inductively coupled plasma-mass spectrometry (ICP-MS) for this type of analysis is described.     

Determination of thallium in water samples

This article illustrates the developments of effective preconcentration techniques and highly sensitive detection methods for accurate measurements of Tl species at extremely low concentration in aqueous solutions. The literature on this topic was taken from the Analytical Abstracts in the period 1990-2005.     

Measurements of short-lived cosmogenic nuclides in rain samples

Summary Extremely low activity levels of cosmic ray induced nuclides have been measured in freshly precipitated rainwater by quick chemical separation coupled with ultra low background gamma-spectrometry. The nuclides detected were ³⁸S (T_1/2 = 2.83 h)-³⁸Cl (37.2 m), ³⁹Cl (55.6 m), ²⁴Na (14.96 h), ²⁸Mg (20.9 h), ⁷Be (53.3 d) and ²²Na (2.602 y). The number of atoms in rain water were evaluated to be ranging from 400-1900 l^-1 for ³⁹Cl (n = 6, mean: 1200), 30-1500 l^-1 for ²⁴Na (n = 16, mean: 520), 80-600 l^-1 for ²⁸Mg (n = 13, mean: 260), 1 ^. 10⁶-4 ^. 10⁷ l^-1 for 7Be (n = 16, mean: 7 ^. 10⁶) and 2 ^. 10³-1 ^. 10⁵ l^-1 for ²²Na (n = 9, mean: 2 ^. 10⁴). Measurements of activity levels and activity ratios of short-lived cosmic-ray induced short-lived nuclides will open new method to understand atmospheric processes occurred at the altitude of rain cloud.     

Determination of aluminium in natural water samples

The atmospheric deposition of terrestrial dust into the ocean is an important factor in controlling Earth's climate. Aluminium can be used as a tracer for the magnitude and location of dust transported from the land to surface ocean. The element is ideal for this purpose since its primary input is via aeolian dust deposition and it has a short surface water residence time. The accurate determination of dissolved aluminium in seawater is difficult due to the complexity of the matrix and the trace (nanomolar) concentrations at which the metal exists. This paper presents a critical review of the different sampling and analytical methods for the determination of the concentration of aluminium in natural waters, with particular focus on techniques successfully applied to shipboard analysis of seawater.     

Determination of trialkyllead species in water samples

An analytical compound procedure is described for the determination of trimethyl- and triethyllead in water samples like rain, melted snow, and surface waters. The method consists of an enrichment step (adsorption onto and elution from silica gel), a chromatographic separation with column switching (HPLC including pre-column enrichment), and a spectrophotometric detection (chemical reaction detector). The detection limits for the whole procedure, starting with 500 ml sample volume, are 15 pg/ml and 20 pg/ml for trimethyl- and triethyllead resp. The standard deviation for repeated analysis of a sample containing 90 pg Et3Pb+/ml is calculated to +/- 4%. The method also covers the analysis of the chemically mixed trialkyllead species Me2EtPb+ and MeEt2Pb+. The investigation of several water samples taken from different locations shows the presence of trimethyl- and triethyllead in the concentration range of 20-100 pg/ml.     

Determination of long-lived radionuclides in radioactive wastes from the IEA-R1 nuclear research reactor

Ion-exchange resins and activated charcoal beds are employed for purification of the cooling water that is pumped through the core of pool type nuclear research reactors. Once expended, these media are replaced and become radioactive wastes that contain low concentrations of long-lived fission and activation products, uranium isotopes and transuranium elements. Determination of the radioactive inventory is of paramount importance in the management of such radioactive wastes, which, besides high-energy photon emitters that can be identified and quantified directly by gamma-ray spectrometry, also contain pure alpha, pure beta and low-energy photon emitters whose quantitative determination require radiochemical separation. These later are collectively known as difficult to measure (DTM) radionuclides. A characterization program embracing the DTM radionuclides is currently in progress for spent ion-exchange resins and activated charcoal beds that were definitively withdrawn from the water cleanup system of the IEA-R1 nuclear research reactor. Radiochemical methods used in the characterization program include separations with specific anionic resins, chromatographic extractions and co-precipitation, which enabled the measurement of the activity concentrations of ⁹⁰Sr, ²³⁴U, ²³⁵U, ²³⁸U, ²³⁸Pu, ^239+240Pu, ²⁴¹Pu, ²⁴¹Am and ²⁴⁴Cm. An enhanced retention of uranium and transuranium elements was observed in the activated charcoal compared to the ion-exchange resins as a result of the tendency of actinides to undergo hydrolysis in aqueous solutions.     

Determination of creatinine in clinical samples with a creatininase reactor and an ammonia probe

A commercial nylon coil with immobilized creatininase in conjunction with a potentiometric ammonia probe is used in a continuous flow apparatus for the determination of creatinine in blood plasma and urine. The analytical characteristics of the coil are evaluated and its specific enzymatic activity is calculated. The determination of creatinine in plasma is viable provided that samples are processed quickly after they have been taken and that plasma ammonia is evaluated just before the creatinine determination. Analyses of urine require prior separation of ammonia. For plasma, 40 samples/hour can be processed with confidence. The precision of the procedure depends strongly on the plasma ammonia level and is about 5% for normal conditions.     

The paper chromatographic isolation of nuclides in air samples

A method is outlined for the quantitative transfer of nuclides of strontium, barium, cerium, zirconium, lanthanum, yttrium, and niobium from solution to a paper for Chromatographic separation. Carrier quantities of iron are precipitated as the hydroxide from a carbonate solution and filtered directly onto the Chromatographic paper. A two-dimensional development is utilized to isolate the individual nuclides.This separation procedure is applied to air dust samples containing nuclear debris. Radiometric determinations may be conveniently made by γ-spectrometric or conventional low-background β-measurements.     

Determination of epichlorohydrin in water and sewage samples

The simple, quick and effective methods for the analysis of epichlorohydrin (ECH) in water and sewage samples with the use of gas chromatography have been presented. From among all the methods developed, the procedures for monitoring drinking-water quality and the methods which allow the determination of epichlorohydrin in sewage samples have been selected.

The limits of ECH detection have been determined by direct aqueous injection (DAI) into the chromatographic column and an analysis with the application of a flame ionization detector (FID), a mass spectrometry detector (MS), an electron capture detector (ECD) and atomic emission detection (AED) detectors. The method allows the determination of ECH in water samples at the concentration level of 0.1 mg l⁻¹. Moreover, the developed methods of water samples preparation for chromatographic analysis using the following extraction methods: headspace (HS), stripping with adsorption on solid phase, liquid–liquid extraction (LLE), solid phase extraction (SPE) and solid phase microextraction (SPME) have been evaluated. The limits of ECH detection for each procedure with the application of gas chromatography (GC) combined with various detectors have been determined and their statistical evaluation has been presented. The SPME method allowed us to determine ECH in water samples at the concentration levels of 1.0 ng l⁻¹.

The results of studies on the choice of the selective methods allowing ECH analysis in sewage samples have been demonstrated. The applied SPME method was found to be a quick and effective technique to determine micro trace amounts of ECH in samples containing high amounts of various organic compounds.     

Use of k0 concept to corrections for interferences from fissionable nuclides in reactor NAA

A neutron spectrum-independent compound nuclear constant, Ik_o, is proposed for fission interference corrections in reactor NAA by parametric method. Ik₀ values for eight major fission interference cases, belonging to three different types, have been determined in six irradiation positions (with _th/ _e 13,7–134) of three research reactors in our Institute. The general agreement among experimental Ik₀ 's from different irradiation positions and between experimental and calculated Ik₀ values for the same interference case verifies the validity of the method. Calculated Ik₀ values for all the possible fission interferences are tabulated. Interferences from²³⁸U(n,) and²³²Th(n,) reactions and reactor fast neutron induced²³⁸U(n, f) and²³²Th(n, f) reactions are discussed.     

Determination of pyridine in soil and water samples of a polluted area

A method for the analyses of pyridine in environmental samples is described. For soil samples a distillation procedure followed by an extraction, an acidic extraction or a Soxhlet extraction can be used. For water samples a distillation procedure followed by extraction can be employed. Deuterated pyridine is used as an internal standard and the extracts are analyzed by GC-MS. The recoveries of the methods are higher than 80%; the detection limits for pyridine are 0.01 mg/kg for soil samples and 0.2 g/l for water samples.     

A scintillation method for determination of actinide alpha-activity in samples

This report describes an efficient, easy to use, and inexpensive method for detection of alpha-activity in biological samples, the alpha radiometer. The actinide elements are coprecipitated from acid-dissolved, ashed samples with bismuth phosphate and the precipitate is then mixed with ZnS(Ag) scintillation powder. The mixture is dried, in a thin layer, on the surface of a polystyrene cuvet and scintillations from the layer are detected with a photomultiplier tube. An optimal counting efficiency is obtained with a scintillation powder thickness between 25 and 40 mg·cm⁻².     

Sequential determination of actinide isotopes and radiostrontium in swipe samples

Assays of alpha- and beta-emitting radionuclides in swipe samples are often required to monitor the presence of removable surface contamination for radiological protection and control in nuclear facilities. Swipe analysis has also proven to be a very sensitive analytical technique to detect nuclear signatures for safeguard verification purposes. A new sequential method for the determination of actinide isotopes and radiostrontium in swipe samples, which utilizes a streamlined column separation with stacked anion and extraction chromatography resins, has been developed. To validate the separation procedure, spike and blank samples were prepared and analyzed by inductively coupled mass spectrometry (ICP-MS), alpha spectrometry and liquid scintillation (LS) counting. Low detection limits have been achieved for isotopic analysis of Pu (²³⁸Pu, ²³⁹Pu, ²⁴⁰Pu, ²⁴¹Pu), U (²³⁴U, ²³⁵U, ²³⁸U), Am (²⁴¹Am), Cm (²⁴²Cm, ^243/244Cm) and Sr (⁹⁰Sr) at ultra-trace concentration levels in swipe samples.