2维全自动亥姆霍兹线圈磁块测量方法

在波荡器和扭摆器的研制过程中,为提高磁块的测量效率和精度,提出了2维全自动亥姆霍兹线圈磁块测量方法。通过理论推导得到仅采用2维全自动旋转而不需要3维旋转就可以实现磁块的全自动测量,降低了磁块全自动测量的实现难度。根据该方法的理论,已成功研制出一台2维全自动亥姆霍兹线圈测量装备,并在上海光源的磁块测量中使用。系统地给出2维全自动亥姆霍兹线圈磁块的测量理论和方法,并对测量误差进行了分析,该系统实现了磁块剩磁测量的高效率、高精度和高重复性,可以在30 s内完成单磁块的测量,重复性和精度均好于510-4。     

翻转线圈系统在波荡器积分场测量中的应用

 为了更有效地测量用于上海同步辐射光源波荡器的积分场误差,在已有的伸展线磁测系统的基础上研制了一套翻转线圈磁测系统,该系统的运动控制、数据采集和数据分析处理均可自动完成。在利用这套磁测系统测量3.4×10^-6 T·m磁场积分时获得高于1×10^-6 T·m的测量精度,初步的实验结果表明这套波荡器积分磁场测量系统具有测量精度好、速度快的特点,与已有的伸展线磁测系统、平移线圈磁测系统和霍尔点测系统相比,它更适合于测量波荡器的一、二次场积分和多极场分量。     

用模拟退火法进行纯永磁波荡器磁块组合优化

 纯永磁波荡器由多个磁块组成,磁块的剩磁离散性会引起波荡器磁场误差,从而影响储存环工作状态和自发辐射谱质量。在波荡器磁块安装之前,使用模拟退火法对磁块进行组合排序优化,可以使峰值场强误差降低到10 ^-4量级以下,磁场一次积分降低到10^-6 T·m量级,二次积分降低到10 ^-6 T·m ²量级,优化结果不依赖于初始状态的选择。给出优化的详细过程,提出了根据磁块剩磁快速计算波荡器峰值场强误差和积分场的方法。     

上海深紫外自由电子激光装置波荡器磁场调整

 在对上海深紫外项目的波荡器建造过程中,应用亥姆霍兹线圈系统测量了全部单磁块,并使用模拟退火法对磁块进行组合排序优化,使反映磁场的成本函数下降了3个数量级。对一段波荡器进行了多次测量、调整,使积分场、峰峰值误差、位相误差等各项指标达到设计要求。     

粒子加速器丝线位置测量电容传感器标定方法北大核心CSCD

在高能同步辐射光源中,为了提高磁铁的准直精度,采用磁中心代替机械中心进行磁铁标定,通过振动线或旋转线等技术获得磁铁的磁中心位置,以及通过电容式位移传感器测量得到丝线的位置,从而实现磁中心与准直靶标的关联。为了实现丝线位置的高精度测量,必须对电容传感器进行精确标定,因此介绍了一种电容式位移传感器,并对其标定方法进行了研究,提出了网格化的数据采集方式以及高阶多项式拟合的数据处理方法,搭建了传感器标定平台并开发了相应的标定控制程序,实现了对传感器的自动控制、数据采集和高精度标定过程。经过分析与对比,标定后的电容传感器达到μm级的位移测量精度,为磁铁的高精度准直提供了基础。     

W波段同轴静磁波荡器自由电子激光优化设计

基于同轴静磁波荡器的自由电子激光主要利用环形电子束与同轴TE模式的相互作用产生电磁辐射,是一种重要的毫米波辐射源。分析了同轴结构作用区内外半径、工作模式、电子束电压、波荡器周期等参数对辐射频率的影响规律,研究了电子束平均半径的选取原则和束波互作用腔的设计方法,设计了辐射频率在W波段的基于同轴静磁波荡器的自由电子激光,并进行了粒子模拟,在电子束电压为720 kV,电子束流为1 kA的情况下,获得了频率107 GHz、辐射功率35 MW的TE01模,束波转换效率为4.9%,束波作用腔总长度小于200 mm,同轴静磁波荡器的磁场幅度0.34 T。     

上海深紫外自由电子激光波荡器的端部磁结构设计

 针对固定间隙的上海深紫外自由电子激光（SDUV-FEL）混合型波荡器的端部,用Radia程序进行了模拟计算。在端部不加任何电磁线圈补偿的情况下,通过减小端部磁铁、磁极的体积和变动端部磁极位置的方法对波荡器磁场进行了优化,优化以后波荡器横向磁场的边缘场强度降到5×10^-4 T（距离端部磁块边缘10 mm处）,边缘场波形没有了明显突起,优化后的横向磁场的一次积分曲线和二次积分曲线都有很大改善,端口处的一次积分值、二次积分值接近于零。     

HL-2M装置磁探针研制

介绍了 HL-2M 装置磁探针的研制,包括有效面积和极向布局的设计、骨架加工和探针绕制、有效面积和频率响应的标定以及定位安装。通过提高加工精度、有效面积的标定精度和定位安装精度,保证了磁探针系统的测量精度。目前,已经在 HL-2M 装置上完成了两组极向阵列的安装。     

混合型波荡器的3维优化

 以波荡器辐射波和共振电子能及混合型波荡器的解析计算为基础，通过3维磁场的有限元计算，在欧洲光源横向优化基础上，给出了同步辐射和自由电子激光用混合型波荡器纵向优化参数，进而给出了用于DUV FEL混合型波荡器的设计计算参数。加侧位和顶部永磁块后，峰值磁场分别提高到0.722T和0.773T，辅助以1μm量级分辨率的磁间隙调节机械系统，磁场分辨率好于10^-4T量级。     

横向聚焦波荡器磁场的计算与分析

横向聚焦波荡器可用于电子束能量较低、函数较小的情况。在现有横向聚焦波荡器设计方案的基础上,通过倾斜磁块端面和磁极面提出了几种不同结构的横向聚焦波荡器方案。利用三维磁场模拟程序Radia,对这些波荡器的聚焦场特性进行了模拟计算,对其聚焦特性与主要参数的关系进行了研究,并与现有其他横向聚焦波荡器的聚焦特性进行了对比。对弱聚焦和强聚焦两种情况,分别给出较好的结构方案。对于弱聚焦,平均聚焦梯度随中心场强的增大而略有增大,变化不明显;对于强聚焦,平均聚焦梯度随中心场强的增大而明显增大,呈高次曲线关系。     

In situ characterization of undulator magnetic fields

A new in situ method is proposed to characterize the peak magnetic fields of undulator sources. The X‐ray beam emitted by the HU52 Apple‐2 undulator of the DEIMOS beamline of the SOLEIL synchrotron is analyzed using the Bragg diffraction of a Si(111) crystal. Measurements over the undulator gap range in linear horizontal polarization are compared with simulations in order to rebuild the Halbach function linking the undulator gaps to their peak magnetic fields. The method presented also allows information about the electron beam to be obtained.     

Mini‐beam collimator enables microcrystallography experiments on standard beamlines

The high‐brilliance X‐ray beams from undulator sources at third‐generation synchrotron facilities are excellent tools for solving crystal structures of important and challenging biological macromolecules and complexes. However, many of the most important structural targets yield crystals that are too small or too inhomogeneous for a `standard' beam from an undulator source, ～25–50 µm (FWHM) in the vertical and 50–100 µm in the horizontal direction. Although many synchrotron facilities have microfocus beamlines for other applications, this capability for macromolecular crystallography was pioneered at ID‐13 of the ESRF. The National Institute of General Medical Sciences and National Cancer Institute Collaborative Access Team (GM/CA‐CAT) dual canted undulator beamlines at the APS deliver high‐intensity focused beams with a minimum focal size of 20 µm × 65 µm at the sample position. To meet growing user demand for beams to study samples of 10 µm or less, a `mini‐beam' apparatus was developed that conditions the focused beam to either 5 µm or 10 µm (FWHM) diameter with high intensity. The mini‐beam has a symmetric Gaussian shape in both the horizontal and vertical directions, and reduces the vertical divergence of the focused beam by 25%. Significant reduction in background was achieved by implementation of both forward‐ and back‐scatter guards. A unique triple‐collimator apparatus, which has been in routine use on both undulator beamlines since February 2008, allows users to rapidly interchange the focused beam and conditioned mini‐beams of two sizes with a single mouse click. The device and the beam are stable over many hours of routine operation. The rapid‐exchange capability has greatly facilitated sample screening and resulted in several structures that could not have been obtained with the larger focused beam.     

Simulations of magnetic microstructure in thin film elements used for programmable motion of magnetic particles

The results of two-dimensional micromagnetic modeling of magnetization patterns in Permalloy ellipses under the influence of rotating constant-amplitude magnetic fields are discussed. Ellipses of two different lateral sizes have been studied, 0.5 μm×1.5 μm and 1 μm×3 μm. The amplitude of the rotating magnetic field was varied between simulations with the condition that it must be large enough to saturate or nearly saturate the ellipse with the field applied along the long axis of the ellipse. For the smaller ellipse size it is found that the magnetization pattern forms an S state and the direction of the net magnetization lags behind the direction of the applied field. At a critical angle of the rotating magnetic field the direction of the magnetization switches by a large angle to a new S state. Both the critical angle and the angle interval of the switch depend on field amplitude. For this new state, it is instead the applied field direction that lags behind the magnetization direction. The transient magnetization patterns correspond to multi-domain patterns including two vortices, but this state never exists for the equilibrated magnetization patterns. The behavior of the larger ellipse in rotating field is different. With the field applied along the long-axis of the ellipse, the magnetization of the ellipse is nearly saturated with a vortex close to each apex of the ellipse. As the field is rotated, this magnetization pattern remains and the net-magnetization direction lags behind the direction of the field until for a certain angle of the applied field an equilibrium multi-domain state is created. Comparisons are made with corresponding experimental results obtained by performing in-field magnetic force microscopy on Permalloy ellipses.     

FEL undulator with permanent ferromagnetic magnets

A terahertz FEL ferromagnetic undulator has been created. The length of the undulator period is 9 cm with the number of the periods at 27. By means of the selection and redistribution of magnetic elements, the spread of the amplitudes of the magnetic field was reduced to 7%. Additional windings of the magnetic elements were used to compensate for residual spread. The required focusing gradient of the magnetic field was obtained as a result of the relative displacement of alternating poles with an opposite charge of the magnetic field along the x axis. Parameters of undulator, including the focusing properties in the horizontal plane, were investigated.     

Correction of electron motion in magnetic undulator

The dynamics of the motion of relativistic electrons in an iron-free magnetic undulator is studied by analytic and numerical methods. The technique presented for calculating the parameters of the correcting sections of the undulator ensures the required direction and coordinates for the emergence of the electron beam from the apparatus.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 9, pp. 87–93, September, 1978.The authors are indebted to A. N. Didenko for his attention to the study.     

振动线准直技术的原理和研究概述

振动线准直技术是一种通过直接测量空间磁场分布情况来进行磁铁设备准直的方法,其原理完全不同于目前国内正在使用的基于磁铁机械结构进行准直的方法。振动线方法具有很高的准直精度和灵敏性,可以用于单个磁铁磁中心测量、磁铁准直标定和多块磁铁磁中心准直等。主要介绍了振动线准直技术的原理、起源和国际上的应用研究概况。     

磁偶极和电四极在磁各向异性介质中的辐射功率

在经典电动力学的框架下,研究了磁各向异性介质中的电磁辐射问题,得到了磁偶极和电四极在磁各向异性介质中的辐射功率表达式.进一步地,通过把各向同性介质中的μrii代入所得辐射功率表达式,得到了与文献相符合的结果,验证了所得结果的正确性.研究结果表明磁偶极和电四极在磁各向异性介质中的辐射功率大小与磁各向异性介质的μrii大小有关,对判断磁偶极和电四极在磁各向异性介质中的辐射效果有较大的帮助.     

Optimization of the lattice function in the planar undulator applied for terahertz FEL oscillators

Since the beta function of the electron beam within the undulator has a great influence on the power gain of the free electron laser (FEL), optimization of the undulator lattice becomes important. In this paper, the transfer matrix of the planar undulator is obtained from differential equations of the electron motion. Based on this, the lattice function of the planar undulator in a terahertz FEL oscillator proposed by Huazhong University of Science and Technology (HUST-FEL) is optimized and the expressions of the average beta function are derived. The accuracy of the optimization result was confirmed well by the numerical method. The application range of this analytical method is given as well. At last, the emittance growth in the horizontal direction due to the attenuation of the magnetic field is discussed.