疏松砂岩水力压裂裂缝形态研究综述

疏松砂岩水力压裂裂缝的典型特征是大量分支缝、微裂缝和一定钝度的裂缝尖端及剪切带的形成等. 主要通过对相关文献的调研,分析了剪切作用、拉伸作用等对裂缝形态特征（起裂、转向、延伸）等力学行为所产生的影响,通过针对一些疏松砂岩的压裂实验研究发现,其滤失过程主要受到缝尖区域的影响,而且滤失一般发生在裂缝扩展之前. 裂缝缝尖周围的局部应力往往是影响裂缝起裂和裂缝开度的主导参数,裂缝的形态特征则是应力、渗透率、流态等综合作用的结果,对疏松砂岩裂缝形态特征的形成做了进一步的解释.     

含预制裂纹L形梁柱试件动态断裂过程

针对含预制裂纹L形梁柱试件,为研究预制裂纹动态扩展的力学特征及其对梁柱试件破坏模式的影响,采用数字动态焦散线实验系统,对距节点核心区不同距离l处含有预制裂纹的试件进行落锤冲击实验,得到预制裂纹的扩展轨迹、速度、动态应力强度因子的变化规律。结果表明,l值增大,扩展裂纹在梁下边缘的贯通点与预制裂纹的夹角逐渐增大,曲裂程度变大。裂纹扩展速度随着l的增大振荡性增强,裂纹扩展平均速度逐渐降低。l值为2 mm时,裂尖表现为Ⅰ型断裂,l值增大,裂尖受到剪应力作用增强,Ⅰ型动态应力强度因子减小,Ⅱ型动态应力强度因子增大,断裂逐渐转变为Ⅰ-Ⅱ复合型。     

Effect of the poisson ratio on the perfectly plastic stress field at a stationary plane-strain crack tip

Under the condition that all the perfectly plastic stress components at a crack tip are the functions of θ only, making use of equilibrium equations and Von-Mises yield condition containing Poisson ratio, in this paper, we derive the generally analytical expressions of perfectly plastic stress field at a stationary plane-strain crack tip. Applying these generally analytical expressions to the concrete cracks, the analytical expressions of perfectly plastic stress fields at the stationary tips of Mode Ⅰ, Mode Ⅱ and Mixed-Mode Ⅰ-Ⅱ plane-strain cracks are obtained. These analytical expressions contain Poisson ratio.     

复合加载下疲劳裂纹扩展速率研究

本文提出了一种计算曲折裂纹尖端应力强度因子的简单方法。对一种油井钻杆材料在不同Ⅰ－Ⅱ复合比加载下的疲劳裂纹扩展行为的研究表明，Ⅱ型成分成对裂纹扩展速率有两种趋势相反的影响作用，并得到了一个计算复合型裂纹扩展速率的Ｐａｒｉｓ形式的公式。     

Perfect elastic-viscoplastic field at mode Ⅰ dynamic propagating crack-tip

The viscosity of material is considered at propagating crack-tip. Under the assumption that the artificial viscosity coefficient is in inverse proportion to power law of the plastic strain rate, an elastic-viscoplastic asymptotic analysis is carried out for moving crack-tip fields in power-hardening materials under plane-strain condition. A continuous solution is obtained containing no discontinuities. The variations of numerical solution are discussed for mode Ⅰ crack according to each parameter. It is shown that stress and strain both possess exponential singularity. The elasticity, plasticity and viscosity of material at crack-tip only can be matched reasonably under linear-hardening condition. And the tip field contains no elastic unloading zone for mode Ⅰ crack. It approaches the limiting case, crack-tip is under ultra-viscose situation and energy accumulates, crack-tip begins to propagate under different compression situations.     

Analytic solutions to crack tip plastic zone under various loading conditions

Based on stress field equations and Hill yield criterion, the crack tip plastic zone is determined for orthotropic materials and isotropic materials under small-scale yielding condition. An analytical solution to calculating the crack tip plastic zone in plane stress states is presented. The shape and size of the plastic zone are analyzed under different loading conditions. The obtained results show that the crack tip plastic zones present “butterfly-like” shapes, and the elastic–plastic boundary is smooth. The size of the plastic zone for orthotropic composites is less at the crack tip for various loading conditions, compared with the case of isotropic materials. Crack inclination angle and loading conditions affect greatly the size and shape of crack tip plastic zone. The mode I crack has a crucial effect on the plastic zone for mixed mode case in plane stress state. The plastic zone for pure mode I crack and pure mode II crack have a symmetrical distribution to the initial crack plane.     

考虑应力松驰复合型裂纹顶端塑性区分析

Ｓｈｉｈ［１］应用奇异单元，获得了不考虑应力松驰小范围屈服条件下复合型裂纹尖端塑性区形状。Ｚ．Ｚ．Ｚｕ等［２］采用Ｒｉｃｅ［５］给出的裂纹尖端应力关系式，利用有限元分析获得了不考虑应力松驰下复合型裂纹尖端塑性区，本文基于静力学中内力与外力平衡条件，用线弹性的全场解代替局部解，给出了考虑应力松驰下复合型裂纹尖端塑性区边界方程，获得了考虑应力松驰下的任意方向的塑性区尺寸及塑性区形状     

Field structure at mode III dynamically propagating crack tip in elastic-viscoplastic materials

An elastic-viscoplastic mechanics model is used to investigate asymptotically the mode Ⅲ dynamically propagating crack tip field in elastic-viscoplastic materials. The stress and strain fields at the crack tip possess the same power-law singularity under a linear-hardening condition. The singularity exponent is uniquely determined by the viscosity coefficient of the material. Numerical results indicate that the motion parameter of the crack propagating speed has little effect on the zone structure at the crack tip. The hardening coefficient dominates the structure of the crack-tip field. However, the secondary plastic zone has little influence on the field. The viscosity of the material dominates the strength of stress and strain fields at the crack tip while it does have certain influence on the crack-tip field structure. The dynamic crack-tip field degenerates into the relevant quasi-static solution when the crack moving speed is zero. The corresponding perfectly-plastic solution is recovered from the linear-hardening solution when the hardening coefficient becomes zero.     

Mode I and mode II crack tip asymptotic fields with strain gradient effects

The strain gradient effect becomes significant when the size of fracture process zone around a crack tip is comparable to the intrinsic material lengthl, typically of the order of microns. Using the new strain gradient deformation theory given by Chen and Wang, the asymptotic fields near a crack tip in an elastic-plastic material with strain gradient effects are investigated. It is established that the dominant strain field is irrotational. For mode I plane stress crack tip asymptotic field, the stress asymptotic field and the couple stress asymptotic field can not exist simultaneously. In the stress dominated asymptotic field, the angular distributions of stresses are consistent with the classical plane stress HRR field; In the couple stress dominated asymptotic field, the angular distributions of couple stresses are consistent with that obtained by Huang et al. For mode II plane stress and plane strain crack tip asymptotic fields, only the stress-dominated asymptotic fields exist. The couple stress asymptotic field is less singular than the stress asymptotic fields. The stress asymptotic fields are the same as mode II plane stress and plane strain HRR fields, respectively. The increase in stresses is not observed in strain gradient plasticity for mode I and mode II, because the present theory is based only on the rotational gradient of deformation and the crack tip asymptotic fields are irrotational and dominated by the stretching gradient. The project supported by the National Natural Science Foundation of China (19704100), National Natural Science Foundation of Chinese Academy of Sciences (KJ951-1-20), CAS K.C. Wong Post-doctoral Research Award Fund and Post-doctoral Science Fund of China     

Field structure at mode Ⅲ dynamically propagating crack tip in elastic-viscoplastic materials

An elastic-viscoplastic mechanics model is used to investigate asymptotically the mode Ⅲ dynamically propagating crack tip field in elastic-viscoplastic materials. The stress and strain fields at the crack tip possess the same power-law singularity under a linear-hardening condition. The singularity exponent is uniquely determined by the viscosity coefficient of the material. Numerical results indicate that the motion parameter of the crack propagating speed has little effect on the zone structure at the crack tip. The hardening coefficient dominates the structure of the crack-tip field. However, the secondary plastic zone has little influence on the field. The viscosity of the material dominates the strength of stress and strain fields at the crack tip while it does have certain influence on the crack-tip field structure. The dynamic crack-tip field degenerates into the relevant quasi-static solution when the crack moving speed is zero. The corresponding perfectly-plastic solution is recovered from the linear-hardening solution when the hardening coefficient becomes zero.     

Stress-strain field near crack tip and calculation of critical stress of crack propagation in a pure bending beam of rectangular section with one-sided mode i crack

This paper studies the stress-strain field near crack tip in a pure bending beam of rectangular section with one-sided mode I crack by the analytic method of Ref. [1], then it gives the stress and strain components at the crack tip when the crack propagates and further it obtains the formulas of calculating the elastic deformed area width, the deformed intensity area width and the equation groups of calculating the critical stress of crack propagation, last the equation group of calculating critical stress of crack propagation is verified by calculating instance. The maximum error is 0.18%. First Received May 7, 1994.     

改进型扩展比例边界有限元法

结合了扩展有限元法(extended finite elementmethods,XFEM)和比例边界有限元法(scaled boundary finite elementmethods,SBFEM)的主要优点,提出了一种改进型扩展比例边界有限元法(improvedextended scaled boundary finite elementmethods,$i$XSBFEM),为断裂问题模拟提供了一条新的途径.类似XFEM,采用两个正交的水平集函数表征材料内部裂纹面,并基于水平集函数判断单元切割类型;将被裂纹切割的单元作为SBFE的子域处理,采用SBFEM求解单元刚度矩阵,从而避免了XFEM中求解不连续单元刚度矩阵需要进一步进行单元子划分的缺陷;同时,借助XFEM的主要思想,将裂纹与单元边界交点的真实位移作为单元结点的附加自由度考虑,赋予了单元结点附加自由度明确的物理意义,可以直接根据位移求解结果得出裂纹与单元边界交点的位移;对于含有裂尖的单元,选取围绕裂尖单元一圈的若干层单元作为超级单元,并将此超级单元作为SBFE的一个子域求解刚度矩阵,超级单元内部的结点位移可通过SBFE的位移模式求解得到,应力强度因子可基于裂尖处的奇异位移(应力)直接获得,无需借助其他的数值方法.最后,通过若干数值算例验证了建议的$i$XSBFEM的有效性,相比于常规XFEM,$i$XSBFEM的基于位移范数的相对误差收敛性较好;采用$i$XSBFEM通过应力法和位移法直接计算得到的裂尖应力强度因子均与解析解吻合\较好.      

一种XFEM断裂分析的裂尖单元新型改进函数

提出了一种适用于裂尖改进单元的新型改进函数, 基于三角变换的方法, 保留裂纹尖端场的应力奇异性和裂纹上、下表面的位移不连续性, 将常规扩展有限元法裂尖改进单元的4 项改进函数缩减为2 项, 裂尖改进单元的结点由常规的8 个改进自由度减少为4 个. 采用2 个正交的水平集函数表征材料内部裂纹面, 详细阐述了改进单元类型的判别方法, 给出一种改进单元的分区域积分方案. 最后, 若干断裂力学问题经典算例的数值计算结果表明:建议的裂尖改进函数具有较高的数值精度, 该方法是十分有效的.     

Observation of Stress Field Around an Oscillating Crack Tip in a Quenched Thin Glass Plate

The variation of stress field around an oscillating crack tip in a quenched thin glass plate is observed using instantaneous phase-stepping photoelasticity. The successive images around the propagating crack are recorded by a CCD camera that is equipped with a pixelated micro-retarder array. Then, the phase maps of the principal stress difference and the principal direction are easily obtained even though the photoelastic fringes cannot be visualized. The path of the crack growth as well as the stress intensity factors and the crack tip constraint are obtained from these phase distributions. Results show that the mode I stress intensity factor and the crack tip constraint vary remarkably with the crack growth. In addition, the results show that the mode-II stress intensity factor exists even though the crack propagates smoothly.     

爆炸载荷下板条边界斜裂纹的动态扩展行为

为了研究爆炸应力波作用下板条边界斜裂纹的动态扩展行为,首先分析了爆炸应力波在含边界斜裂纹板条中的传播,其次采用动态焦散线实验方法,进行了爆炸载荷下板条边界斜裂纹扩展规律的实验研究.研究结果表明,爆炸应力波作用下,板条试件边界斜裂纹的扩展过程中,裂纹扩展速度、扩展加速度和裂尖动态应力强度因子随时间波动变化,扩展速度最大值...     

基于神经网络的界面裂纹尖端场分析

通过构造反向传播神经网络,对裂纹尖端的应力场进行模拟,进而实现对裂纹尖端应力场甬数的逼近。得到的网络具有较高的联想、记忆能力和相当的稳定性,并且可以快速、准确地得到带裂纹构件的裂纹尖端应力场,从而确定裂纹尖端的塑性区和分析裂纹的扩展。数值计算给出了LY12-CZ材料裂纹扩展方向的计算结果,与实验结果吻合较好,还给出了两相材料含界面裂纹在复合型载荷作用下的塑性区形状的变化情况,并对两相材料含界面裂纹在复合型载荷作用下裂纹的扩展方向进行了预测。     

NiTi形状记忆合金裂纹尖端热力耦合行为研究

本文对NiTi形状记忆合金I型裂纹尖端热力耦合行为进行了数值仿真分析和实验验证。建立了包含相变和热力耦合的本构模型,通过有限元计算得到了裂纹尖端附近的纵向应变、马氏体体积分数和温度场分布,依据马氏体相变情况对裂纹尖端有效应力强度因子进行了修正,揭示了加载速率对形状记忆合金裂纹尖端有效应力强度影子的影响规律。参数研究表明,随着加载频率的增加,裂纹尖端附近温度逐渐升高,马氏体相变区域逐渐缩小,有效应力强度因子呈下降趋势,形状记忆合金表现出增韧效应,有助于减缓裂纹扩展。本研究结果对于揭示热力耦合作用下超弹性形状记忆合金疲劳裂纹扩展规律具有重要参考意义。     

Effect of residual surface stress on the fracture of nanoscale materials

The problem of a mode I crack in nanomaterials under a remote mechanical load is investigated. The effect of the residual surface stress on the crack surface is considered and the solutions to the crack opening displacement (COD) and the stress intensity factor (K_I) are obtained. The results show that the surface effect on the crack deformation and crack tip field are prominent at nanoscale. Moreover, COD and K_I are influenced by the residual surface stress not only on the surface near the crack tip region but also on the entire crack surface.     

Semi-infinite mode III crack propagating at constant velocity in anisotropic medium

The Laplace transform, Wiener-Hopf technique and Cagniard-de Hoop method are used to solve the problem of a mode III semi-infinite crack which propagates suddenly at constant velocity in an anisotropic medium. The transient displacement field and the dynamic stress intensity factor at the moving crack tip are obtained.This research is supported by the Seismological United Foundation.     

STRESS－STBAIN FIELD NEAR CRACK TIP AND CALCULATION OF CRITICAL STRESS OF CRACK PROPAGATION IN A PURE BENDING BEAM OF RECTANGULAR SECTION WITH ONE－SIDED MODEICRACK

ＳＴＲＥＳＳ－ＳＴＢＡＩＮＦＩＥＬＤＮＥＡＲＣＲＡＣＫＴＩＰＡＮＤＣＡＬＣＵＬＡＴＩＯＮＯＦＣＲＩＴＩＣＡＬＳＴＲＥＳＳＯＦＣＲＡＣＫＰＲＯＰＡＧＡＴＩＯＮＩＮＡＰＵＲＥＢＥＮＤＩＮＧＢＥＡＭＯＦＲＥＣＴＡＮＧＵＬＡＲＳＥＣＴＩＯＮＷＩＴＨＯＮＥ－Ｓ...