α-Fe2O3的制备及其性能的研究

使用一定配比的乙酰丙酮,无水乙酸钠,三氯化铁合成的乙酰丙酮铁作为前驱体材料,采用水热法在不同温度条件下反应两小时合成α-Fe₂O₃,从而探寻光催化效率最佳反应条件。利用X-射线粉末衍射仪(XRD),场发射扫描电子显微镜(TEM),紫外可见漫反射光谱仪(UV-vis DRS),比表面积测试(BET),拉曼光谱(Raman spectra)等对材料进行表征分析。分析结果表明在同等情况下175°C下合成的α-Fe₂O₃还原六价铬的反应速率高于其他温度下合成的α-Fe₂O₃光催化速率。     

Morphology controls of the melt blending in a novel highly crosslinked bismaleimide system

A novel bismaleimide of 2,2-bis[4-(4-maleimidophenoxy)phenyl]propane (BMIP) with a broad working-temperature-range for the melt blending was successfully synthesized. BMIP possesses a considerably broad working-temperature-range from 75 °C to 250 °C, prior to undergoing cure reactions to form a highly crosslinked network. The morphology types of cured BMIP/clay hybrids can be controlled by varying the shearing temperatures and the contents of the clay. The conditions necessary for achieving an exfoliated or an intercalated BMIP/clay hybrid were thoroughly investigated via X-ray diffractometry, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). All the uncured samples prepared at different shearing temperatures and with an adequate amount of MMT-C (above 3 phr) exhibited an intercalated form of morphology. However, the crosslinking reactions for specified samples prepared at relatively elevated shearing temperatures (above 120 °C) and with a relatively low content of clay (below 15 phr) resulted in morphology changes from the intercalated form to the exfoliated form of morphology. There exists an isotropically mechanical property for the cured matrix of the exfoliated hybrids whereas there exists an anisotropically mechanical property for the cured matrix of the intercalated hybrids.     

Study on thermal degradation and combustion behaviors of PC/POSS hybrids

Polycarbonate/polyhedral oligomeric silsesquioxane hybrids were prepared based on bisphenol A polycarbonate (PC) and trisilanolphenyl-POSS (TPOSS) by the melt blending method. Investigation of transmission electronic microscopy and Fourier transform infrared spectroscopy confirms that the nanoscale TPOSS particles were well dispersed in the PC matrix and there is no chemical reaction between the TPOSS particles and PC matrix during the melt blending. The thermal degradation behaviors of the PC/TPOSS hybrids were investigated. The presence of TPOSS significantly affects the thermal degradation process of PC. The combustion behaviors of the hybrids were evaluated by cone calorimetry experiments. The addition of TPOSS significantly decreased the value of peak heat release rate of the hybrids. Moreover, the addition of TPOSS at 2 wt% leads to the maximum decrease of the PHRR. And scanning electron microscopy and X-ray photoelectron spectroscopy were used to explore the char residues of the pure PC and the hybrids.     

Two cationic metal-organic frameworks based on cadmium and α,ω-alkanedisulfonate anions and their photoluminescent properties

We have successfully synthesized three cadmium-based metal-organic frameworks by utilizing two separate organic linkers to direct the structure. The first material is a three-dimensional neutral framework based on 2D cadmium ethanedisulfonate layers pillared by a 4,4'-bipyridine linker. The other two materials are 3D cationic frameworks and are the first with propanedisulfonate and butanedisulfonate as extraframework charge balancing anions. Both structures occupy a high symmetry hexagonal crystal system where Cd-bipy chains are arranged into three crystallographically distinct layers that stack spirally along [001]. The framework is stabilized by alkanesulfonate anions that are electrostatically and hydrogen bonded to the framework. Each material was characterized by single-crystal and powder X-ray diffraction. The thermal and luminescent properties were also investigated by thermogravimetric analysis and photoluminescence spectroscopy, respectively. All three materials exhibit high thermal stability to above 300 °C and efficient blue emissive photoluminescence centered at 425 nm to 450 nm upon 350 nm excitation.     

Preparation and Characterization of Cu(II) Phthalocyanine Tetrasulfonate Intercalated and Supported on Layered Double Hydroxides

The aim of the present work was to synthesize and characterize layered doublehydroxides (LDHs), in the magnesium/aluminum form, intercalated with copper(II)phthalocyanine tetrasulfonate (CuPcTs). The metal complex was immobilized intothe LDH gallery region through the reconstitution method and this material wascharacterized by X-ray diffraction (XRD), surface area and porosity measurements,elementary analysis, thermogravimetry (TGA), vibrational (IR) and electronic(UV-visible) spectroscopies, and electronic paramagnetic resonance (EPR). Thecatalytic performance of CuPcTs intercalated and supported on the LDH wasevaluated by carrying out the hydrogen peroxide dismutation. The CuPcTs wassuccessfully intercalated into the LDH layers according to XRD data (the basalspacing of the carbonate precursors increases by approximately 15Å inthe intercalated samples). The surface area and porosity analysis suggested thatthe CuPcTs intercalated materials are not microporous solids. Samples containingthe metal complex confined between the LDH layers have an appreciable thermalstability: decomposition is not observed at least up to 400 °C. TGA experiments also show that the weight-loss curves of the CuPcTs supported samples superimpose those recorded for the CuPcTs complex and the LDH-carbonate while the curves for theintercalated materials are unique. CuPcTs intercalated or supported on LDHs is notactive in the hydrogen peroxide dismutation although the free form shows activity at pH above 8.     

Immobilization of anionic iron(III) porphyrins into ordered macroporous layered double hydroxides and investigation of catalytic activity in oxidation reactions

The first generation anionic iron(III) porphyrin [Fe(TSPP)] and the second generation anionic complexes [Fe(TDFSPP)], [Fe(TCFSPP)], and [Fe(TDCSPP)] were immobilized into three-dimensionally macroporous layered double hydroxide (3DM-LDH), using the direct reconstruction of 3DM-LDH from macroporous mixed oxides MOX or the anionic exchange on DDS intercalated 3DM-LDH. The macroporous layered double hydroxides were obtained at the surface of nanometric polystyrene spheres, which were synthesized by an inverse opal method. Polystyrene was removed after calcination in oxidizing atmosphere, nanostructured mixed oxides (3DM-MOX) were obtained, which after reconstruction give origin to macroporous layered double hydroxide (3DM-LDH). Following metalloporphyrin immobilization, the resulting materials were characterized by powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), UV–vis (glycerin mull) spectroscopy, attenuated total reflectance Fourier transform infrared spectroscopy (ATR/FTIR), and electron paramagnetic resonance (EPR). Results revealed that the complexes are either immobilized at the surface of the macroporous layered double hydroxide or intercalated between the layers, displacing some dodecylsufate anions. The obtained materials were investigated as catalysts for oxidation reactions, to find out whether they function as cytochrome P-450 models.     

Relaxations of confined chains in polymer nanocomposites: Glass transition properties of poly(ethylene oxide) intercalated in montmorillonite

The relaxation behavior of poly(ethylene oxide) (PEO), intercalated in montmorillonite, a naturally occurring mica-type silicate, was studied by differential scanning calorimetry (DSC) and thermally stimulated dielectric depolarization (or thermally stimulated current, TSC). The materials were synthesized by melt or solution-mediated intercalation. In both intercalates, the PEO chains were confined to ca. 0.8-nm galleries between the silicate layers. The solution intercalate contained a fraction of unintercalated PEO chains which exhibited a weak and depressed PEO melting endotherm in DSC. In contrast, the melt intercalate was “starved” such that almost all the PEO chains were effectively intercalated. For these melt intercalates, no thermal events were detected by DSC. TSC thermal sampling technique was used to examine the glass transition regions and to estimate the extent of cooperativity of chain motions. The motions of the intercalated PEO chains are inherently noncooperative relative to the cooperative T_g motions in the amorphous portion of the bulk polymer. This is presumably due to the strong confining effect of the silicate layers on the relaxations of the intercalated polymer. © 1997 John Wiley & Sons, Inc.     

Synthesis of nylon 6–clay hybrid by montmorillonite intercalated with ϵ-caprolactam

It was found that montmorillonite was intercalated with ?-caprolactam. X-ray diffraction revealed that the chain axes of the ?-caprolactam were parallel to the montmorillonite plates. The intercalated montmorillonite was swollen by molten ?-caprolactam at 200°C. ?-Caprolactam and 6-aminocaproic acid (accelerator) were polymerized with the intercalated montmorillonite at 260°C for 6 h, yielding a nylon 6-clay hybrid. X-ray diffraction and transmission electron micrography revealed that the silicate layers of the hybrid were uniformly dispersed in the nylon 6 matrix. Mechanical properties of the hybrid were improved. The strength and the modulus of the hybrid increased compared with the previously reported nylon 6 clay-hybrid (NCH) synthesized by montmorillonite intercalated with 12-aminolauric acid. The heat distortion temperature (HDT) of the hybrid was 164°C, which was 12°C higher than that of NCH. © 1993 John Wiley & Sons, Inc.     

Intercalation and functionalization of zinc hydroxide nitrate with mono- and dicarboxylic acids

The intercalation of ions derived from succinic, glutaric, and adipic acid into layered zinc hydroxide nitrate by ionic exchange reaction is reported. Different reaction conditions are investigated and the materials are characterized by powder X-ray diffraction, Fourier transform infrared spectroscopy, thermal analysis (simultaneous thermogravimetry and differential scanning calorimetry) and elemental analysis. The dicarboxylic acids can be grafted to the matrix slab by one carboxylate group and the second hydrated carboxylate group is hanging between the layers. Benzoate ions have also been intercalated by both ionic exchange reaction and stirring in acetonitrile. The two benzoate-intercalated materials exchange the organic moiety by sulfate ions if stirred in magnesium sulfate solution, but the sample obtained by anion exchange also allows the unusual incorporation of neutral magnesium sulfate in addition to free solvated sulfate ion. A schematic arrangement of the intercalated species between the layers is presented.     

Mechanism of dehydroxylation temperature decrease and high temperature phase transition of coal-bearing strata kaolinite intercalated by potassium acetate

The thermal decomposition and dehydroxylation process of coal-bearing strata kaolinite-potassium acetate intercalation complex (CSKK) has been studied using X-ray diffraction (XRD), infrared spectroscopy (IR), thermal analysis, mass spectrometric analysis and infrared emission spectroscopy. The XRD results showed that the potassium acetate (KAc) have been successfully intercalated into coal-bearing strata kaolinite with an obvious basal distance increase of the first basal peak, and the positive correlation was found between the concentration of intercalation regent KAc and the degree of intercalation. As the temperature of the system is raised, the formation of KHCO(3), KCO(3) and KAlSiO(4), which is derived from the thermal decomposition or phase transition of CSKK, is observed in sequence. The IR results showed that new bands appeared, the position and intensities shift can also be found when the concentration of intercalation agent is raised. The thermal analysis and mass spectrometric analysis results revealed that CSKK is stable below 300°C, and the thermal decomposition products (H(2)O and CO(2)) were further proved by the mass spectrometric analysis. A comparison of thermal analysis results of original coal-bearing strata kaolinite and its intercalation complex gives new discovery that not only a new mass loss peak is observed at 285 °C, but also the temperature of dehydroxylation and dehydration of coal bearing strata kaolinite is decreased about 100 °C. This is explained on the basis of the interlayer space of the kaolinite increased obviously after being intercalated by KAc, which led to the interlayer hydrogen bonds weakened, enables the dehydroxylation from kaolinite surface more easily. Furthermore, the possible structural model for CSKK has been proposed, with further analysis required in order to prove the most possible structures.     

Flammability and phase-transition studies of nylon 6/montmorillonite nanocomposites

Nylon 6 (PA6)/clay hybrids have been prepared using a direct melt intercalation technique by two processes. One is PA6 melt-mixing with modified clay, the other is PA6 melt-mixing with natural (Na⁺ base) clay using an ammonium salt bearing long alkyl chains as a polymer/clay reactive compatibilizer. Their structure and flammability properties are characterized by X-ray diffraction, transmission electron microscopy and cone calorimeter experiments. The results of the cone calorimeter experiments show that hybrids made by these two processes have a lower heat release rate peak and higher thermal stability than that of original PA6. Meanwhile, X-ray diffraction was used to investigate PA6/clay hybrids with various cooling histories from the melt, including medium-rate cooling (air cooling) and rapid cooling (water-quenched). In contrast to pure PA6 dominated by the α phase, the addition of clay silicate layers by these two methods favors the formation of the γ crystalline phase in PA6/clay hybrids. Flammability and phase-transition studies confirm that silicate layers added by these two methods have a similar nanoeffect and nanodispersion in the PA6 matrix.     

离子交换法合成MTX/LDHs复合物的研究及体外细胞实验的探索

研究了不同水热温度下合成的层状双金属氢氧化物(layered double hydroxides,LDHs)对离子交换法制备的MTX/LDHs纳米复合物的影响.并利用透射电镜(TEM)、X-射线衍射(XRD)、MTT等手段,对纳米复合物的结构及载药量、控释-缓释性、生物细胞活性母体等性质进行了系统研究.结果表明,不同LDHs母体对离子交换后复合物的形貌和性质起着至关重要的作用.在磷酸缓冲液中考察了MTX/LDHs纳米复合物的药物控释性能并进行了动力学拟合,结果表明,采用离子交换法制备MTX/LDHs纳米复合物的释药过程是Fick扩散控制的离子交换和粒内扩散过程.最后,采用MTT法探究了MTX/LDHs纳米复合物对肺癌细胞A549增殖的抑制作用,结果表明,复合物较纯的MTX具有更好的抑制癌细胞增殖的作用.     

熔融法制备聚氧化乙烯/蒙脱土杂化材料及其结晶行为

聚氧化乙烯;熔融插入;纳米杂化;熔融法制备聚氧化乙烯/蒙脱土杂化材料及其结晶行为     

Characterization of HDPE /Polyamide 6/ Nanocomposites Using Scanning-and Transmission Electron Microscopy

Summary: Preparation and morphology of high density polyethylene (HDPE)/ polyamide 6 (PA 6)/modified clay nanocomposites were studied. The ability of PA 6 in dispersing clays was used to prepare modified delaminated clays, which were then mixed with HDPE. Mixing was performed using melt processing in a torque rheometer equipped with roller rotors. After etching the materials with boiling toluene and formic acid at room temperature, the morphology was examined by SEM analyses, showing that the PA 6 formed the continuous phase and HDPE the dispersed phase. X-ray diffraction patterns show that the (001) peak of the clay is dramatically decreased and shifted to lower angles, indicating that intercalated/exfoliated nanocomposites are obtained. TEM analyses confirmed the typical structure of exfoliated nanocomposites. A scheme for the mechanism of exfoliation and/or intercalation of these HDPE /PA 6/ /organoclay nanocomposites is proposed.     

Cs4UGe8O20: a tetravalent uranium germanate containing four- and five-coordinate germanium

A very rare tetravalent uranium germanate has been synthesized under hydrothermal conditions at 585 °C and 160 MPa. Its structure contains layers of single-ring Ge(3)O(9)(6-) germanate anions that are connected by UO(6) octahedra and dimers of edge-sharing GeO(5) trigonal bipyramids to form a three-dimensional framework with intersecting 6- and 7-ring channels. UV-visible, photoluminescence, and U 4f X-ray photoelectron spectroscopy were used to confirm the valence state of uranium.     

Vermiculite as a useful host for guest cyclic aliphatic amine intercalation, followed by cation adsorption

Two vermiculite hybrids containing aliphatic amines intercalated were synthesized. The amount of guest molecules intercalated resulted in 0.60 and 0.52 mmol g⁻¹ for pyperidine and pyperazine, respectively, which reflect the effectiveness of such kind of reactions. The processes were confirmed by elemental analysis and infrared spectroscopy. X-ray diffraction patterns suggested that the original crystallinity of matrix was maintained, however, the intercalation process is associated with the conformation of the guest molecule and the presence of the compensate cation inside the interlayer cavity. The intercalated inorganic hosts adsorb divalent lead, nickel, copper and cobalt cations, more effectively at basic pH value, from aqueous solution, which content of adsorption is higher than the precursor native vermiculite.     

Comparison of solution-blending and melt-intercalation for the preparation of poly(ethylene-co-acrylic acid)/organoclay nanocomposites

Ethylene-acrylic acid copolymers (EAAs) and commercial montmorillonite clays organically modified with dimethyldihydrogenatedtallowammonium ions (Cloisite^® 15A and 20A) were used for the synthesis of nanocomposites by melt-compounding, static melting of polymer/clay mixtures and solution-intercalation in order to compare the effectiveness of these procedures and to shed light on the thermodynamics and the kinetics of the intercalation process. The preparation from solution was made by the use of several solvents, such as toluene, xylene, chloroform, etc., which were then removed from the hybrids by precipitation in different non-solvents or by evaporation. Particular attention was paid to the effect of the thermal treatments which are often used when processing the composites prepared from solution. X-ray diffraction (XRD) of the solution-blended composites showed that no intercalation of the EAAs inside the clay galleries can be achieved if solvent removal is made by precipitation in non-solvents or by room-temperature evaporation. On the contrary, intercalation was found to occur very rapidly (in less than 1 min) when both the hybrids prepared from solution and the mechanical blends of powdered components were melted in the absence of shear. Polymer intercalation was also found to occur, though with a lower rate, upon annealing the powder mixtures at temperatures lower than the EAA melting point. Microscopic observations made by polarized optical microscopy, scanning electron microscopy and transmission electron microscopy showed that the clay particles dispersion is appreciably lower for the composites prepared from solution, compared to those produced in the melt under shear flow conditions. The hybrids obtained by static melting of powder mixtures, on the other side, were expectedly found to comprise micron sized clay agglomerates, although intercalation was demonstrated also for these materials by XRD. The structure of the intercalated silicate layers stacks, characterized by an interlayer spacing of 4.0 nm, was shown to be independent of the preparation procedure and to correspond to thermodynamic equilibrium.     

New layered double hydroxides containing intercalated manganese oxide species: synthesis and characterization

Manganese oxide species (MnO(x)) have been intercalated within the gallery spaces of Mg-Al layered double hydroxides (LDHs). Synthesis of these materials was achieved by ion-exchange of the LDH-nitrate precursor with permanganate anion followed by reduction with organic reagents, such as glucose, ethanol, and ascorbic acid. Elemental analysis, X-ray diffraction, FT-IR spectroscopy, Raman spectroscopy, HR-TEM, and N(2) sorption analyses have been used to characterize these materials. TEM micrographs of LDH-MnO(x) materials revealed platelike morphology, characteristic of hydrotalcite-like compounds. Chemical analysis results showed that permanganate anions exchanged with nitrate anions. FT-IR and Raman spectroscopy confirmed the reduction of the permanganate anions after treatment with the organic reagents. The XRD diffraction patterns of LDH-MnO(x) revealed that the layer structure is maintained after all synthetic steps. The observed basal spacings of intercalates varied depending on the reducing agent; the largest expansion was 9.93A, corresponding to the use of ascorbic acid. The specific surface areas were also affected according to the organic reagent used, indicating that the structural modifications in the interlayer domain observed by X-ray diffraction also influence the microtextural properties.     

Effects of annealing and isothermal crystallization upon crystalline forms of poly(vinylidene fluoride)

Poly(vinylidene fluoride) exists in three crystalline forms. Optimum conditions for preparing form III were established by infrared spectroscopy, differential scanning calorimetry, and x-ray diffraction measurements. Form III is easily obtained by annealing mats of solution-grown crystals of form II at 175–185°C and is also preferentially formed by isothermal crystallization from the melt between 165 and 175°C. Below 165° crystallization of form II is favored. The melting point of form III is higher than that of form II.     

Embedded high density metal nanoparticles with extraordinary thermal stability derived from guest-host mediated layered double hydroxides

A chemical precursor mediated process was used to form catalyst nanoparticles (NPs) with an extremely high density (10(14) to 10(16) m(-2)), controllable size distribution (3-20 nm), and good thermal stability at high temperature (900 °C). This used metal cations deposited in layered double hydroxides (LDHs) to give metal catalyst NPs by reduction. The key was that the LDHs had their intercalated anions selected and exchanged by guest-host chemistry to prevent sintering of the metal NPs, and there was minimal sintering even at 900 °C. Metal NPs on MoO(4)(2-) intercalated Fe/Mg/Al LDH flakes were successfully used as the catalyst for the double helix growth of single-walled carbon nanotube arrays. The process provides a general method to fabricate thermally stable metal NPs catalysts with the desired size and density for catalysis and materials science.