Fabrication and structural characterization of nanocomposites consisting of Ni nanoparticles dispersed in polyimide films

Formation and structure of composite layer consisting of polyimide films containing Ni nanoparticles were investigated. The preparation method relies on KOH treatment on polyimide film to form carboxyl acid groups and adsorption of Ni ions by ion exchange followed by hydrogen reduction. The amount of Ni ions adsorbed in polyimide films were found to be systematically controlled by changing initial KOH concentration, subsequent ion exchange time, pH and temperature. Cross-sectional TEM observation revealed that Ni nanoparticles with 3-5 nm in diameter were homogeneously dispersed in the surface modified polyimide layer after heat treatment above 250 ^°C in H₂ atmosphere. The size and distribution of the Ni nanoparticles were strongly dependent on the heat treatment temperature, indicating that this method allows microstructural tuning of metal/polymer nanocomposites.     

Fabrication and characterization of iron oxide nanoparticles filled polypyrrole nanocomposites

The effect of iron oxide nanoparticle addition on the physicochemical properties of the polypyrrole (PPy) was investigated. In the presence of iron oxide nanoparticles, PPy was observed in the form of discrete nanoparticles, not the usual network structure. PPy showed crystalline structure in the nanocomposites and pure PPy formed without iron oxide nanoparticles. PPy exhibited amorphous structure and nanoparticles were completely etched away in the nanocomposites formed with mechanical stirring over a 7-h reaction. The thermal stability of the PPy in the nanocomposites was enhanced under the thermo-gravimetric analysis (TGA). The electrical conductivity of the nanocomposites increased greatly upon the initial addition (20 wt%) of iron oxide nanoparticles. However, a higher nanoparticle loading (50 wt%) decreased the conductivity as a result of the dominance of the insulating iron oxide nanoparticles. Standard four-probe measurements indicated a three-dimensional variable-range-hopping conductivity mechanism. The magnetic properties of the fabricated nanocomposites were dependent on the particle loading. Ultrasonic stirring was observed to have a favorable effect on the protection of iron oxide nanoparticles from dissolution in acid. A tight polymer structure surrounds the magnetic nanoparticles, as compared to a complete loss of the magnetic iron oxide nanoparticles during conventional mechanical stirring for the micron-sized iron oxide particles filled PPy composite fabrication.     

Fabrication and performance characterization of Al/Ni multilayer energetic films

Al/Ni multilayer bridge films, which were composed of alternate Al and Ni layers with bilayer thicknesses of 50, 100 and 200 nm, were prepared by RF magnetron sputtering. In each bilayer, the thickness ratio of Al to Ni was maintained at 3:2 to obtain an overall 1:1 atomic composition. The total thickness of Al/Ni multilayer films was 2 μm. XRD measurements show that the compound of AlNi is the final product of the exothermic reactions. DSC curves show that the values of heat release in Al/Ni multilayer films with bilayer thicknesses of 50, 100 and 200 nm are 389.43, 396.69 and 409.92 J?g^?1, respectively. The temperatures of Al/Ni multilayer films were obviously higher than those of Al bridge film and Ni bridge film. Al/Ni multilayer films with modulation of 50 nm had the highest electrical explosion temperature of 7000 K. The exothermic reaction in Al/Ni multilayer films leads to a more intense electric explosion. Al/Ni multilayer bridge films with modulation period of 50 nm explode more rapidly and intensely than other bridge films because decreasing the bilayer thickness results in an increased reaction velocity.     

Fabrication and characterization of transparent superhydrophobic thin films based on silica nanoparticles

A simple method, which was based on self-assemble of silica nanoparticles and heptadecafluorodecyl trimethoxysilane, was used to fabricate a transparent superhydrophobic thin film with a water contact angle higher than 146°. The film has a uniform thickness of about 200 nm and a certain surface roughness about 20 nm, which makes it both transparent and superhydrophobic. PACS 06.60.Ei; 81.07.Pr; 81.16.Dn; 81.20.Fw; 81.65.-Ps     

Fabrication and characterization of a granular film consisting of size-selected silver nanoparticles: application to a SERS substrate

Uniform-sized silver nanoparticles with average diameter of 13.7 nm have been prepared in the gas-phase by combining a pulsed laser ablation method with a low pressure-differential mobility analyzer (LP-DMA). By depositing the silver nanoparticles onto a silicon substrate, a granular film consisting of size-selected silver nanoparticles has been fabricated and its morphology and electronic properties have been examined using transmission electron microscopy (TEM) and UV-visible absorption spectroscopy. This granular silver film serves as a highly active substrate for surface-enhanced Raman scattering (SERS).     

Fabrication and characterization of anodic ZnO nanoparticles

We have successfully fabricated ZnO nanoparticles by anodizing Zn sheet in 0.1 M sodium hydroxide solution. Morphology observations demonstrate that the sizes of the ZnO nanoparticles have a tendency to increase with rising anodic voltage. Detailed structural characterizations illuminate that oxygen vacancies exist in the anodic ZnO nanoparticles with wurtzite structure. Photoluminescence from the ZnO nanoparticles exhibits a very broad visible emission band, which can be Gaussian divided into three subbands around 2.4, 2.8, and 3.0 eV. Spectral examinations and analyses reveal that the three subbands are connected with oxygen vacancies, interstitial zinc sites, and the ZnO_x matrix, respectively. Our results improve the understanding of the light-emitting mechanism in ZnO nanomaterials. PACS 61.46.Df; 81.05.Dz; 78.55.-m     

Solgel synthesis and structural characterization of silver-silica nanocomposites

The solgel process has been successfully used to prepare silver/silica nanocomposites. After drying in air at 50°C for 30 min, samples were heat treated in air, at 100, 200, 400 and 500°C for the formation of silver nanoparticles. Evolution of silver nano-particles in the amorphous SiO₂ matrix as a function of annealing temperature has been studied. Characterizations were made by X-ray diffraction, ultraviolet-visible, and infrared spectroscopy. Mechanisms of silver clusters formation in the densified silica matrix with respect to thermal treatment are discussed.     

Fabrication and structural characterization of metal films coated on cenosphere particles by magnetron sputtering deposition

Metal films were successfully coated on cenosphere particles using a magnetron sputtering deposition system in which a newly designed sample stage equipped with an ultrasonic vibration generator was used for the tumbling of cenosphere particles. It was found by FE-SEM and AFM results that the films were well compacted and highly uniform in thickness. Due to the difference in sputtering rate, the film thicknesses estimated from FE-SEM characterizations in backscattered mode were <10, 39, 50 and 134 nm for Co, Ni, Cu and Ag films, respectively, under the same sputtering deposition conditions. The RMS values derived from the AFM measurements were 1.94, 4.31, 10.92 and 18.33 nm for Co, Ni, Cu and Ag films, respectively, which can ascribe to the different crystallization behaviors for the four metals. The experiment results indicate that the coating method can be applicable for the fabrication of many other films on cenosphere particles which can be sputter deposited.     

Magnetic characterization of maghemite nanoparticles dispersed in surface-treated polymeric template

Magnetic characterization of maghemite nanoparticles dispersed in a polymeric template and treated under different chemical processes is reported in this work. Particle size estimated from magnetic measurements, D _M?≈?10 nm, for the free-surfactant sample, is consistent with values determined from XRD analysis and TEM images. The magnetic collapse of sextets towards a quadrupole doublet as the temperature is increased reveals the thermal relaxation of smaller $\upgamma $ -Fe₂O₃ nanoparticles. Magnetic measurements show a strong irreversibility between ZFC and FC curves suggesting the occurrence of particle–particle interaction.     

Fabrication and characterization of sputtered titanium dioxide films

TiO₂ thin films were prepared under various conditions by using a reactive RF sputtering technique. The structural, optical and electrical characteristics of the films have been investigated. All as-deposited films were amorphous. After annealing at T > 673 K, the crystallinity of the observed tetragonal anatase phase appeared improved. The optical band gap, determined by using Tauc plot, has been found to amount to 3.38 ± 0.03 and 3.21 ± 0.03 eV for the direct and indirect transition, respectively. Also the complex optical constants for the wavelength range 300-2500 nm are reported. Using the two-point probe technique, the dark resistivity has been measured as a function of the film thickness, d. The resistivity, ρ, of the samples has been found to decrease markedly with increasing thickness, but only for d < 100 nm. The behaviour of ρd versus d was found to fit properly with the Fuchs and Sondheimer relation with parameters ρ_o = 4.95 × 10⁶ Ω cm and mean free path, l = 310 ± 2 nm. The log ρ versus 1/T curves show three distinct regions with values for the activation energy of 0.03 ± 0.01, 0.17 ± 0.01 and 0.50 ± 0.02 eV, respectively.     

Fabrication and characterization of thermo-sensitive magnetic polymer composite nanoparticles

Novel dual-functional nanospheres composed of Fe₃O₄ nanoparticles embedded in a thermo-sensitive polymer were synthesized by emulsifier-free emulsion polymerization. The Fe₃O₄ nanoparticles were prepared by chemical precipitation. The surface of these particles was modified by oleic acid to achieve stability against agglomeration. These stable particles were then polymerized using N-isopropylacrylamide as the main monomer, divinylbenzene as the crosslinker and potassium persulfate as the initiator. The nanospheres were characterized by Fourier-transform infrared spectrum, transmission electron microscopy, thermogravimetric analysis, vibrating sample magnetometer and dynamic light scattering. The results show that the lower critical solution temperature of thermo-sensitive magnetic immunomicrospheres was between 40 and 45 °C.     

Fabrication and characterization of polymer blends consisting of cationic polyallylamine and anionic polyvinyl alcohol

Thin sheets of polyallylamine (PAAm) and polyvinyl alcohol (PVA) blend were prepared by employing solution casting technique for potential membranes application. The blends were characterized by Fourier transform infrared (FTIR) and ¹H-NMR spectroscopy, scanning electron microscopy, thermogravimetric analysis, ultraviolet–visible spectroscopy, X-ray diffraction, and mechanical properties. The zeta potential, conductivity and rheological properties of PAAm/PVA blends were also studied. The FTIR spectrum reveals that the C–H asymmetric stretching vibration band of PVA at 2,928 cm^?1 disappeared in all the blend samples. Thermal stability of the blend membrane was better than pure polymers. The crystallinity of the PAAm/PVA blends was decreased, which may be due to the entanglement of PAAm in to PVA chains, which is also responsible for the improvement in the mechanical properties of the blends. Zeta potential decreases where as the conductivity increases as a function of temperature. Hydrophilicity is improved by addition of PVA to PAAm, which may be due to hydroxyl group of PVA. The blend solution shows non-Newtonian character of the liquid. By applying shear stress, increase in the effect of rarefaction was observed. The knowledge about the investigated parameters will be of vital importance for use of the blended material in membrane applications, especially where CO₂ separation is in focus. The membrane performance (separation properties) of the PAAm/PVA blended material is, however, not reported in the current article.     

Synthesis and investigation of the structure of nanocomposites based on nickel nanoparticles dispersed in a phthalocyanine matrix

A method based on doping of pure nickel phthalocyanine (NiPc) with a polycrystalline potassium powder at relatively low temperatures (300°C) has been proposed for the synthesis of a magnetic nanocomposite containing nickel nanoparticles stabilized in the NiPc matrix. The structural analysis of the synthesized nanoparticles and changes in the NiPc initial matrix has been performed using X-ray diffraction, X-ray absorption spectroscopy, and transmission electron microscopy. It has been found that, at the doping level used in this study, the synthesized samples of the K_xNiPc nanocomposites contain from 9 to 18% Ni in the form of metallic magnetic nanoparticles with an average size of more than 40 nm. It has been shown that the formation of nanoparticles is accompanied by a relative misorientation of persistent NiPc molecules with the unchanged structure of each of these molecules. The stabilization of nickel nanoparticles by the phthalocyanine matrix leads to the fact that the synthesized nanocomposites acquire time-conserving magnetic properties.     

Fabrication and electromagnetic performance of micro-tubular nanocomposites composed of monodisperse iron nanoparticles and carbon

Low density and thin thickness are essential for electromagnetic (EM) wave absorbers. In this study, we fabricated a novel micro-tubular iron nanocomposite (MTIC) that composed of carbon microtubes and monodisperse iron nanoparticles (NPs). The bulk density of MTIC is only 0.35±0.04 g cm⁻³ due to its micro-tubular structure. The presence of iron NPs increased the magnetic loss significantly and therefore enhanced the reflection loss (RL) of MTIC/paraffin composite. The optimum thickness for the composite is 1.5-1.8 mm, with maximum bandwidth of 7.6 GHz for RL<−5 dB and 3.6 GHz for RL<−10 dB. The corresponding frequency at this thickness is 10-18 GHz. Because of low density and broad bandwidth at thin thickness, MTIC is a promising light-weight absorber for EM wave absorption or microwave shielding. This study will also provide new ideas for fabricating microwave absorbers with low density and thin thickness.     

Synthesis and characterization of Ni magnetic nanoparticles in AlMCM41 host

Superparamagnetic nickel nanoparticles were prepared by incorporating nickel ion into AlMCM41 as a nanoreactor and then reduced with sodium borohydride or H₂ gas. Products were characterized by elemental analysis, transmission electron microscopy, X-ray powder diffraction, and magnetic susceptibility. The nickel particle size and blocking temperature depend on the reduction method.     

Chemical synthesis and structural characterization of small AuZn nanoparticles

In this paper, we report the aqueous synthesis of bimetallic Au-Zn nanoparticles of different compositions by the simultaneous reduction technique. The stability and atomic configuration of the particles are studied through high-resolution transmission electron microscopy (HRTEM) and UV-Vis optical absorption techniques. Depending on the composition, small bimetallic nanoparticles of 1–15 nm in size were obtained. The average size and size distribution of the bimetallic nanoparticles are seen to be critically dependent on the atomic ratio of the constituting elements Au and Zn. While a 1:1 atomic proportion of Au and Zn produced most stable nanoparticles of smallest average size, nanoparticles produced with higher content of either of the component elements are unstable, inducing agglomeration and coalescence to form elongated structures with uneven morphologies. Au₃Zn₁ nanoparticles followed a directional growth pattern, producing bimetallic nanorods with multiple crystalline domains. Interestingly, in these rod-like nanostructures, the domains are in well array of solid solution-like bimetallic and pure mono-metallic regions alternatively. Such nanostructures with uneven morphology and compositions might show distinct catalytic selectivity in chemical reactions. PACS 61.46.-w; 87.64.Ee; 74.62.Bf     

Fabrication,morphologies and structural characterization of InN nanowire arrays

Large-scale, uniform diameter, and high-aligned metal indium was first introduced into the nanochannels of anodic aluminum membrane by electrochemical deposition. InN nanowires were achieved by the reaction of indium vapor with a constant flowing ammonia atmosphere. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used to measure the size and structure of the sample. The results show that InN nanowires were aligned in the nanochannels of the template and the diameters were about 40 nm. Raman-scattering spectrum of InN nanowire array is presented. The \({ A}_{1}\) (TO), \({ E}_{1}\) (TO), and \({ E}_{2}\) (high) phonon frequencies at 440, 472, and 490 cm \(^{-1}\) were observed. The Raman spectrum of the InN nanowire arrays is consistent with the hexagonal wurtzite structure bulk InN, in agreement with X-ray diffraction observation.     

Mineral nanoparticles in dispersed soils

The chemical-mineral composition and morphological features of mineral nanoparticles of clay soils have been studied. In the clay soils of the Moscow moraine, nanoparticles are found to be localized in the surface microcavities of sand and silt grains covered with clay films. They have predominantly anisometric configurations and comprise mainly mixed-layered clay minerals and ferric oxides. The distinctive features of mineral nanoparticles are the high levels of specific surface and cation exchange capacity.