Characterization of fluorocarbon-in-water emulsions with added triglyceride

Fluorocarbon-in-water emulsions are being explored clinically as synthetic oxygen carriers in general surgery. Stabilizing fluorocarbon emulsions against coarsening is critical in maintaining the biocompatibility of the formulation following intravenous administration. It has been purported that the addition of a small percentage of long-chain triglyceride results in stabilization of fluorocarbon emulsions via formation of a three-phase emulsion. In a three-phase emulsion, the triglyceride forms a layer around the dispersed fluorocarbon, thereby improving the adhesion of the phospholipid surfactant to the dispersed phase. In the present study, we examined the effect of triglyceride addition on the physicochemical characteristics of the resulting complex dispersion. In particular, we examined the particle composition and stability of the dispersed particles using a method which first fractionates (classifies) the different particles prior to sizing (i.e., sedimentation field-flow fractionation). It was determined that the addition of a long-chain triglyceride (soybean oil) results in oil demixing and two distinct populations of emulsion droplets. The presence of the two types of emulsion droplets is not observed via light scattering techniques, since the triglyceride droplets dominate the scattering due to a large difference in the refractive index between the particles and the medium as compared to fluorocarbon droplets. The growth of the fractionated fluorocarbon emulsion droplets was followed over time, and it was found that there was no difference in growth rates with and without added triglyceride. In contrast, addition of medium-chain-triglyceride (MCT) oils results in a single population of emulsion droplets (i.e., a three-phase emulsion). These emulsions are not stable to droplet coalescence, however, as significant penetration of MCT into the phospholipid lipid interfacial layer results in a negative increment in the monolayer spontaneous curvature, thereby favoring water-in-oil emulsions and resulting in destabilization of the emulsion to the effects of terminal heat sterilization or mechanical stress.     

Influence of pH on the stability of oil-in-water emulsions stabilized by a splittable surfactant

A laboratory study was conducted to evaluate the effect of pH on the stability of oil-in-water emulsions stabilized by a commercial splittable surfactant Triton SP-190 by comparison with the results obtained by a common surfactant Triton X-100. The emulsion stability was explored by measuring the volume of oil phase separated and the size of the dispersed droplets. It was found that the addition of inorganic acids did not significantly affect the stability of emulsions stabilized by Triton X-100, but had a profound influence on the stability of emulsions stabilized by Triton SP-190. Moreover, the droplet size of a Triton X-100-stabilized emulsion and its dynamic interfacial activity were insensitive to acids. However, at lower pH the droplet size of the emulsions stabilized by Triton SP-190 was considerably increased. From the dynamic interfacial tension measurements the dynamic interfacial activity of Triton SP-190 at the oil/water interface was found to be strongly inhibited by the addition of acids, resulting in a slower decreasing rate of dynamic interfacial tension. The results demonstrate that the dramatic destabilization of Triton SP-190-stabilized emulsions could be realized by the use of acids, which evidently changed the interfacial properties of the surfactant and resulted in a higher coalescence rate of oil droplets.     

Emulsification of caraway essential oil in water by lecithin and β-lactoglobulin: emulsion stability and properties of the formed oil–aqueous interface

The stability and droplet size of protein and lipid stabilised emulsions of caraway essential oil as well as the amount of protein on the emulsion droplets have been investigated. The amount of added protein (β-lactoglobulin) and lipid (phosphatidylcholine from soybean (sb-PC)) were varied and the results compared with those obtained with emulsions of a purified olive oil. In general, emulsions with triglyceride oil proved to be more stable compared with those made with caraway essential oil as the dispersed phase. However, the stability of the emulsions can be improved considerably by adding sb-PC. An increase in the protein concentration also promoted emulsion stability. We will also present how ellipsometry can be used to study the adsorption of the lipid from the oil and the protein from the aqueous phase at the oil–water interface. Independently of the used concentration, close to monolayer coverage of sb-PC was observed at the caraway oil–aqueous interface. On the other hand, at the olive oil–aqueous interface, the presence of only a small amount of sb-PC lead to an exponential increase of the layer thickness with time beyond monolayer coverage. The amounts of β-lactoglobulin adsorbed at the caraway oil–aqueous interface and at the olive oil–aqueous interface were similar, corresponding roughly to a protein monolayer coverage.     

Ethanol-in-oil emulsion (E/O) stabilized by polyglycerol polyricinoleate: A potential delivery system for ethanolic extract

This study evaluated how variations in polyglycerol polyricinoleate (PGPR) concentration and ethanol dispersed phase content affect the stability of ethanol-in-oil (E/O) emulsions. Results indicate that the stable 10?wt% E/O emulsions can be produced using 2?wt% PGPR. Increasing the ethanol dispersed phased content at constant PGPR concentration caused instability in emulsion. These emulsions remained stable to droplet flocculation and coalescence in the presence of Centella asiatica ethanol extract. PGPR does not greatly decrease the interfacial tension of the ethanol–oil interface. However, it adsorbed at the interface and stabilized the ethanol droplets in the emulsion via steric mechanism.     

A diffusing wave spectroscopy study of the dynamics of interactions between high methoxyl pectin and sodium caseinate emulsions during acidification

A non-invasive technique, diffusing wave spectroscopy (DWS), and traditional dynamic light scattering (DLS) were used to study the interactions of high methoxyl pectin (HMP) with sodium caseinate-stabilized emulsion droplets. At pH 6.8, the droplet size measured by DLS did not change as a function of HMP concentration (up to 0.3%). However, the droplet diameter measured by DWS kept relatively constant up to 0.07% HMP after which it showed drastic increases. The turbidity parameter 1/l* decreased with HMP concentration and levelled off at 0.07% HMP, indicating that the system underwent reorganization and reached equilibrium at 0.07% HMP. During acidification at pH 5.4, right before the pH of aggregation of control emulsions, all emulsions containing 0.05–0.2% HMP showed an increase of 1/l*. This increase indicated the interaction of HMP with sodium caseinate at the interface. Emulsions containing 0.05 and 0.1% HMP also showed destabilization, and the pH of destabilization depended on the concentration of HMP. Sufficient amounts of HMP (0.2%) stabilized the caseinate-coated oil droplets, and the mean square displacement slope was close to 1 throughout, indicating free diffusion of emulsion droplets.     

Hydrophilic polymer foams with well‐defined open‐cell structure prepared from pickering high internal phase emulsions

Open‐cell hydrophilic polymer foams are prepared through oil‐in‐water Pickering high internal phase emulsions (HIPEs). The Pickering HIPEs are stabilized by commercial titania (TiO₂) nanoparticles with adding small amounts of non‐ionic surfactant Tween85. The morphologies, such as average void diameter and interconnectivity, of the foams can be tailored easily by varying the TiO₂ nanoparticles and Tween85 concentrations. Further, investigation of the HIPE stability, emulsion structure and the location of TiO₂ nanoparticles in resulting foams shows that the surfactant tends to occupy the oil‐water interface at the contact point of adjacent droplets, where the interconnecting pores are hence likely to be formed after the consolidation of the continuous phase. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

SEMICONTINUOUS EMULSION POLYMERIZATION OF VINYL ACETATE X. KINETICS OF HOMOPOLYMERIZATION,CO POLYMERIZATION,AND INITIATOR DECOMPOSITION IN THE PRESENCE OF SULFOSUCCINATE-TYPE SURFACTANTS

ABSTRACT

Miorocrystalline cellulose stabilized emulsions (o/w) were evaluated by means of brightfield and polarized light microscopy, freeze-etch electron microscopy, droplet size analyses and rheologic measurements. These studies indicated that miorocrystalline cellulose (Avicel RC591 ) forms a network around emulsified oil droplets. This structure provides a mechanical barrier at the o/w interface which stabilizes the emulsion without the necessity for decreasing interfacial tension, as in conventional surfactant-stabilized emulsions. Rheologic studies indicated that emulsions containing Avicel RC591 had a considerable degree of thlxotropy which contributed to their stability. When Tween 80 was incorporated in this system, oil droplets coalesced indicating that the stability of the emulsion was affected adversely.     

Effect of surfactant sucrose ester on physical properties of dairy whipped emulsions in relation to those of O/W interfacial layers

Dairy foams were manufactured on a pilot plant with various sucrose ester contents. Oil-in-water emulsions were produced by high-pressure homogenisation of anhydrous milk fat (20 wt%) with an aqueous phase containing skim milk powder (6.5 wt%), sucrose (15 wt%), hydrocolloids (2 wt%), and sucrose esters. Sucrose ester content was varied from 0 to 0.35 wt%. Firmness and stability of dairy foams were determined. The fraction of protein associated with emulsion fat droplets and the compression isotherms of those droplets were determined as a function of sucrose ester content. With less than 0.1 wt% sucrose ester, no foam could be produced. The most firm and stable foams were obtained with ca. 0.1 wt% sucrose ester. The fraction of protein associated with emulsion droplets suddenly falls from 60% at a sucrose ester content lower than 0.1125% down to ca. 10-20% for higher surfactant content. Compression isotherms of emulsion droplets at the air-water interface show that, in the presence of surfactant, emulsion droplets disrupt and spread at the interface whilst without surfactant they become dispersed. This means that the presence of sucrose ester causes some destabilisation of fat droplet interfacial layers. There is hence an optimal sucrose ester content that allows some destabilisation of the oil-water interface without concomitant protein displacement from that interface. Consequently, with the recipe and manufacturing process used to produce dairy foams, there exists a compromise in sucrose ester content with regards to manufacture and shelf-life of dairy foams.     

Physicochemical properties of structured phosphatidylcholine in drug carrier lipid emulsions for drug delivery systems

Drug carrier emulsions were prepared with structured phosphatidylcholine (PC-LM) which has both a long hydrocarbon chain and a medium hydrocarbon chain, and the characteristics of PC-LM as an emulsifier were investigated by measuring the creaming ratio, the surface tension of the emulsion system, and the mean particle size and zeta potential of the oil droplets in emulsions. The emulsion prepared with PC-LM as an emulsifier kept the condition and the ratio of separation was lower than those with purified egg yolk lecithin (PEL). The mean particle size of the emulsion prepared with PC-LM was smaller than that with PEL when using only sonication, approximately 250 nm. When using a high-pressure homogenizer after sonication, the mean emulsion size with PC-LM was also smaller than with PEL, approximately 150 nm. The surface tension of the various emulsions and the zeta potential of the emulsion droplets were measured to investigate the stability of the systems. In emulsions with PC-LM or PEL, the surface tension as an index of stability increased as the pressure of the homogenizer increased. Moreover, the zeta potential of the emulsion droplets prepared with PC-LM also increased with an increase in pressure of the homogenizer. As a result, it was found that the drug carrier emulsion prepared with PC-LM had significant advantages in terms of stability and mean diameter. We considered it could be used for the preparations of nanoparticle dispersion systems in drug delivery systems.     

Structures and stability of lipid emulsions formulated with sodium caseinate

The physicochemical properties of emulsions play an important role in food systems as they directly contribute to texture, sensory and nutritional properties of foods. Sodium caseinate (NaCas) is a well-used ingredient because of its good solubility and emulsifying properties and its stability during heating. One of most significant aspects of any food emulsion is its stability. Among the methods used to study emulsion stability it may be mentioned visual observation, ultrasound profiling, microscopy, droplet size distribution, small deformation rheometry, measurement of surface concentration to characterize adsorbed protein at the interface, nuclear magnetic resonance, confocal microscopy, diffusing wave spectroscopy, and turbiscan. They have advantages and disadvantages and provide different insights into the destabilization mechanisms. Related to stability, the aspects more deeply investigated were the amount of NaCas used to prepare the emulsion, and specially the oil-to-protein ratio, the mobility of oil droplets and the interactions among emulsion components at the interface. It is known that the amount of protein required to stabilize oil-in-water emulsions depends, not only on the structure of protein at the interface, and the average diameters of the emulsion droplets, but also on the type of oils and the composition of the aqueous phase. Several authors have investigated the effect of a thickening agent or of a surface active molecule. Factors such as pH, temperature, and processing conditions during emulsion preparation are also very relevant to stability. There is a general agreement among authors that the most stable systems are obtained for conditions that produce size reduction of the droplets, an increase in viscosity of the continuous phase and structural changes in emulsions such as gelation. All these conditions decrease the molecular mobility and slow down phase separation.     

Some Emulsion Features

Traditionally, emulsions have been defined as consisting of two liquids, of which one is dispersed in the other as macroscopic drops, stabilized by mono‐molecular layer of surfactant at the interface. However, a large majority of commercial emulsions are more complex than so and the added elements are essential for the properties of the emulsions including their stability.

With this in mind, this treatment of emulsions is divided into emulsions with mono‐layers and multilayers at the interface. In addition, additional elements in emulsions are described; such as lyotropic liquid crystals, vesicles, microemulsion droplets and solid particles, and their potential influence on the emulsion properties is indicated.     

Pickering emulsions with controllable stability

We prepare solid-stabilized emulsions using paramagnetic particles at an oil/water interface that can undergo macroscopic phase separation upon application of an external magnetic field. A critical field strength is found for which emulsion droplets begin to translate into the continuous-phase fluid. At higher fields, the emulsions destabilize, leading to a fully phase-separated system. This effect is reversible, and long-term stability can be recovered by remixing the components with mechanical agitation.     

Creaming Stability of Flocculated Monodisperse Oil-in-Water Emulsions

The influence of droplet flocculation on the creaming stability of monodisperse n-hexadecane oil-in-water emulsions was studied. The creaming velocity of emulsions with different droplet radii (0.43 and 0.86 μm), droplet concentrations (1-67 vol%), and sodium dodecyl sulfate (SDS) concentrations (7-80 mM) were measured. Depletion flocculation was observed in the emulsions when the aqueous phase SDS concentration exceeded a particular level ( approximately 40 mM for 0.43-μm droplets and approximately 15 mM for 0.86-μm droplets). Creaming was monitored by measuring the back-scattered light from an emulsion as a function of its height. The creaming velocity increased with increasing flocculation and decreased with increasing droplet concentration. These results have important implications for the formulation of emulsion-based materials. Copyright 2000 Academic Press.     

Influence of interfacial characteristics on Ostwald ripening in hydrocarbon oil-in-water emulsions

The influence of the nature of the interfacial membrane on the kinetics of droplet growth in hydrocarbon oil-in-water emulsions was investigated. Droplet growth rates were determined by measuring changes in the droplet size distribution of 1 wt % n-tetradecane or n-octadecane oil-in-water emulsions using laser diffraction. The interfacial properties of the droplets were manipulated by coating them with either an SDS layer or with an SDS-chitosan layer using an electrostatic deposition method. The emulsion containing SDS-coated octadecane droplets did not exhibit droplet growth during storage for 400 h, which showed that it was stable to Ostwald ripening because of this oils extremely low water-solubility. The emulsion containing SDS-coated n-tetradecane droplets showed a considerable increase in mean droplet size with time, which was attributed to Ostwald ripening associated with this oils appreciable water-solubility. On the other hand, an emulsion containing SDS-chitosan coated n-tetradecane droplets was stable to droplet growth, which was attributed to the ability of the interfacial membrane to resist deformation because of its elastic modulus and thickness. This study shows that the stability of emulsion droplets to Ostwald ripening can be improved by using an electrostatic deposition method to form thick elastic membranes around the droplets.     

Water mass transfer in W/O emulsions

Water transportation through the oil phase in W/O emulsions and in W1/O/W2 systems (W/O emulsion in contact with water) was examined. Substance diffusion through interfaces led to interface instability and spontaneous emulsification which caused nanodispersion formation. The photomicrographs of Pt/C replicas of emulsions showed the presence in the continuous oil phase a lot of nanodispersion droplets with a diameter in the range 17-25 nm. Diffusion coefficient (D) of water calculated on the base of Lifshiz-Slezov-Wagner (LSW) equation was about 15 times lower than the coefficients of molecular diffusion. Since such emulsions were extremely unstable toward coalescence, the growth of water droplets took place through as Ostwald ripening as coalescence. In three-phase W1/O/W2 systems diffusion of water, Rhodamine C, and ethanol was studied. D calculated on the base of the equation of nonstationary diffusion were approximately 1000 times lower than molecular ones. It was assumed, that nanodispersion droplets were more likely water carriers in investigated W/O emulsions stabilized by sorbitan monooleate.     

Hydrophobicity Enhances the Formation of Protein-Stabilized Foams

Screening proteins for their potential use in foam applications is very laborious and time consuming. It would be beneficial if the foam properties could be predicted based on their molecular properties, but this is currently not possible. For protein-stabilized emulsions, a model was recently introduced to predict the emulsion properties from the protein molecular properties. Since the fundamental mechanisms for foam and emulsion formation are very similar, it is of interest to determine whether the link to molecular properties defined in that model is also applicable to foams. This study aims to link the exposed hydrophobicity with the foam ability and foam stability, using lysozyme variants with altered hydrophobicity, obtained from controlled heat treatment (77 °C for 0–120 min). To establish this link, the molecular characteristics, interfacial properties, and foam ability and stability (at different concentrations) were analysed. The increasing hydrophobicity resulted in an increased adsorption rate constant, and for concentrations in the protein-poor regime, the increasing hydrophobicity enhanced foam ability (i.e., interfacial area created). At higher relative exposed hydrophobicity (i.e., ~2–5 times higher than native lysozyme), the adsorption rate constant and foam ability became independent of hydrophobicity. The foam stability (i.e., foam collapse) was affected by the initial foam structure. In the protein-rich regime—with nearly identical foam structure—the hydrophobicity did not affect the foam stability. The link between exposed hydrophobicity and foam ability confirms the similarity between protein-stabilized foams and emulsions, and thereby indicates that the model proposed for emulsions can be used to predict foam properties in the future.     

Stimuli-responsive liquid foams: From design to applications

Stimuli-responsive liquid foams and bubbles are systems for which the stability, structure, shape, and movement can be controlled by the application of stimuli. The foam stability can be modified by a stimulus which can change solution condition (pH, temperature, and ionic strength) or with the application of an external field (light and magnetic). Different foam stabilizers have been described in the literature to design these responsive foams systems ranging from surfactants, peptides, polymers, soft polymer particles, surfactants self-assembly, crystalline particles, emulsion droplets, and solid particles. This review aims to cover the recent advances of the design of stimuli-responsive liquid foams and their applications. Responsive liquid foams are attractive in textile coloring process, biomedical application, washing, and material recovery processes.     

MINIEMULSION FORMATION BY TRANSITIONAL INVERSION

Very fine emulsions with droplet size in the sub-micron range, often called miniemulsions, are prepared by the moderate (magnetic) stirring of a system undergoing a dynamic transitional inversion driven by a continuous change in physicochemical formulation (here temperature). Near optimum formulation for three-phase systems, the ultralow interfacial tension favors the drop breaking rate, and fine emulsions can be made. However, this region is also known for its rapid coalescence rate. Thus, a high enough stability can be attained only by shifting the formulation away from optimum as soon as the emulsion is made. Moreover, a rapid change in formulation through the three-phase region also results in a separation phenomenon that can be harnessed to produce ultra fine droplets.

The phase behavior of surfactant-oil-water systems and emulsion properties (type, droplet size and stability) are studied as a function of surfactant concentration (2 wt.% and 6 wt.%), for two different nonionic surfactants (polyoxyethylene tri-terbutyl ethers and sorbitan derivatives) with HLB ranging from 4 to 16. Kerosene and paraffin oil are used as oil phases. The transitional inversion form W/O to O/W is induced by a rapid cooling of the stirred systems from above to below the optimum temperature for three-phase behavior.

Miniemulsions are attained when the surfactant concentration is high enough, and when the temperature quenching span covers an appropriate range related to phase behavior.     

Oil-in-water emulsions stabilized by hydrophobically modified hydroxyethyl cellulose: adsorption and thickening effect

The preparation and stability of oil-in-water emulsions stabilized by hydrophobically modified hydroxyethyl cellulose (HMHEC) were investigated. The rheological measurements of aqueous HMHEC were studied. It was found that HMHEC showed much better thickening ability than the parent (HEC) from which it was derived, which is caused by the association of the hydrophobic alkyl chains, which are absent in HEC. The oscillatory experimental results of the emulsions showed that at higher concentrations, HMHEC could form an elastic gel, which has good thixotropic properties. The stability and droplet size distribution were investigated by visual observation, photomicrograph and a laser-scattering particle size distribution analyzer. The adsorption of HMHEC at the oil-water interface and the surface of emulsion droplets due to the penetration of the alkyl chains in HMHEC into the oil phase were confirmed by visual observation, the interfacial tension method and an in situ environmental scanning electron microscope (ESEM). The stability of emulsions prepared using HMHEC is based on both an associative thickening mechanism caused by alkyl chains in HMHEC and the adsorption of HMHEC at the oil-water interface, which can form a solid film preventing coalescence of the droplets.     

On the viscoelastic behavior of multiple emulsions

The dynamic viscoelastic behavior of multiple emulsions is investigated. A modified Palierne model is used to predict the storage and loss moduli of multiple emulsions. The multiple emulsions exhibit two relaxation domains due to relaxation of two different interfaces--internal and external. The internal interface is the interface between internal droplets and their suspending medium (primary emulsion continuous-phase). The external interface is the interface between multiple-emulsion droplets and their suspending medium (external continuous-phase). The factors affecting the dynamic viscoelastic behavior of multiple emulsions are discussed.