Sn掺杂ZnO薄膜的室温气敏性能及其气敏机理

采用化学气相沉积方法在预制好电极的玻璃基底上制备出Sn掺杂ZnO薄膜和纯ZnO薄膜. 两种样品典型的形貌为四足状ZnO晶须, 其直径约为150-400 nm, 呈疏松状结构. 气敏测试结果显示Sn掺杂ZnO薄膜具有优良的室温气敏性, 并对乙醇具有良好的气敏选择性, 而纯ZnO薄膜在室温条件下对乙醇和丙酮均没有气敏响应. X射线衍射结果表明两种样品均为六方纤锌矿结构. Sn掺杂ZnO样品中没有出现Sn及其氧化物的衍射峰, 其衍射结果与纯ZnO样品对比, 衍射峰向小角度偏移. 光致发光结果表明, Sn掺杂ZnO薄膜与纯ZnO薄膜均出现紫外发光峰和缺陷发光峰, 但是Sn的掺杂使得ZnO的缺陷发光峰明显增强. 将Sn掺杂ZnO样品在空气中退火后, 其室温气敏性消失, 说明Sn掺杂ZnO样品的室温气敏性可能与其缺陷含量高有关. 采用自由电子散射模型解释了Sn掺杂ZnO薄膜的室温气敏机理.     

退火温度对溶胶-凝胶法制备Na掺杂 ZnO薄膜的结构和光学特性的影响

采用溶胶-凝胶旋涂法在Si(100)衬底上制备Na掺杂ZnO薄膜,退火温度分别为873,973,1 073 K。研究了退火温度对Na掺杂ZnO薄膜形貌、微观结构和光学性能的影响。室温光致发光谱显示,在973 K下退火的样品具有中心位于361 nm处尖锐而强的紫外发光峰,在388,425 nm处各有一个比较弱的紫色和蓝色发光峰,在可见光范围内发光峰的强度很弱。     

In掺杂的ZnO纳米棒的共振Raman光谱研究

本文报道In掺杂ZnO纳米棒的成功制备和对其结构以及光荧光性能的详尽研究。在室温条件下ZnO的共振拉曼谱线容易受到很强的荧光干扰, 甚至导致共振拉曼谱线完全被湮没。微量In掺杂入ZnO纳米棒中, 调控紫外发光峰由378 nm(纯ZnO)红移至397 nm; 另外, 在制备过程中引入过量的氧, 在样品中产生大量缺陷, 降低了ZnO的紫外近带边发光峰强度。这两方面导致在室温下可清楚的观察到In掺杂ZnO纳米棒的6阶LO拉曼峰。     

以PVP纳米纤维为模板采用原子层沉积法制备MgxZn1-xO纳米纤维及其光学性质研究

采用静电纺丝方法制备聚乙烯吡咯烷酮(PVP)纳米纤维,并以其为模板采用原子层沉积(ALD)方法制备不同Mg掺杂浓度的MgxZn1-xO纳米纤维。研究了不同Mg掺杂浓度对复合纳米纤维结构和光学性质的影响。利用场发射扫描电子显微镜(FESEM)、光致发光(PL)和紫外-可见光(UV-Vis)吸收谱对样品测试并进行表征分析。结果表明,Mg元素的掺入并没有改变ZnO纳米纤维的形貌,所有样品的表面形貌极其相似,只是掺杂后纤维直径有所增大;随着Mg掺杂浓度的增加吸收边逐渐发生蓝移,表明所制备MgxZn1-xO纤维的带隙具有可调节性。与此同时,在PL谱中可以观察到样品的紫外(UV)发光峰从377nm移动至362nm,且与不掺杂的样品相比,MgxZn1-xO纳米纤维的UV发光强度明显增强。通过这种方法可以合成组分可控的MgxZn1-xO纳米纤维。在ZnO中掺入Mg元素可以有效地提高ZnO-PVP纳米纤维的禁带宽度以及UV发射强度。     

水热法制备钼掺杂ZnO纳米结构及其光学特性研究

用水热法以Zn(NO3)2·6H2O和NaOH为原料,分别以十六烷基三甲基溴化铵(CTAB)、十二烷基硫酸钠(SDS)、聚乙烯吡咯烷酮-K30(PVP-K30)、聚乙二醇400(PEG400)、乙二胺四乙酸(EDTA)为添加剂,制备钼掺杂的纳米ZnO。扫描电镜(SEM)结果表明,通过改变添加剂的种类可以合成不同形貌钼掺杂的ZnO;X射线衍射(XRD)结果表明,掺杂的ZnO纳米粉体为六方纤锌矿结构,随着钼掺杂浓度的增加,衍射峰强度明显增大,结晶质量得到明显改善;室温下的光致发光(PL)图谱表明,掺杂的样品在385 nm处有一紫光发射峰,在约572 nm处有一绿发光射峰,Mo掺杂后明显提高了样品的发光强度。     

碱金属改性的纳米氧化锌基荧光材料

研究了Zn （NO3）2·6H2O、CO （NH2）2、R-C6H4-SO3Na、Eu2O3和LiNO3为原料,通过均匀沉淀法制备了Eu3＋、Li＋共掺杂的纳米ZnO材料,并通过改变Li＋的掺杂比例来研究纳米氧化锌基材料的发光性能,用XRD、紫外和荧光等分析手段对样品进行表征.结果表明：制得的纳米粉体粒径在50nm左右,引入Li＋后增强了纳米ZnO∶Eu3＋材料的紫外可见光吸收和红色发光性能,且与Li＋的掺杂浓度有关,当Li＋∶Eu3＋的摩尔比为0.6时,其在601nm处的特征峰最强.     

高分子网络凝胶法制备ZnO超细粉体及其光学性能

采用高分子网络凝胶法制备球形ZnO超细粉体。通过聚乙烯醇(PVA)亚浓溶液交联网络的空间位阻作用,经过烧结,获得了具有球形形貌的粒径为1~3μm的ZnO粉体颗粒。利用X射线衍射(XRD)、扫描电镜(SEM)分析了不同PVA浓度以及退火温度对产物形貌、结构的影响,发现在PVA溶液浓度为5%,并且经500℃热处理所形成的ZnO球形颗粒最为均匀规整。研究了球形ZnO粉体的光致发光性能,室温下经325nm波长激发,观察到两个中心波长分别位于407,468nm的微弱的荧光发射带,在合适温度下,在385nm处还出现了较强的紫外峰。PL光谱表明,退火温度对ZnO的光致发光影响较大,随着退火温度升高,由于表面缺陷和结晶性能发生变化,407nm处发射峰逐渐减弱消失,而紫外发光先增强后减弱,经500℃热处理样品的紫外发光性能达到最佳。     

硫掺杂ZnO纳米线的电化学制备及发光特性

"采用电场辅助电化学沉积法,利用阳极氧化铝模板模板制备了高度择优取向的硫掺杂ZnO单晶纳米线．X射线衍射仪、隧道电子显微镜、选取电子衍射对所得样品的结构、形貌分析表明,所得纳米线是沿(101)择优取向的六方纤锌矿结构单晶纳米线,长约几十微米、平均直径约70 nm. X射线光电子能谱对化学组成的分析进一步证实掺杂硫原子的存在．用荧光光谱仪(PL)对S掺杂前后的ZnO纳米线进行光学特性测量发现,S掺杂较大地改变了ZnO纳米线的发光性质．在PL谱中,除了有典型的ZnO纳米线在378、392 nm处的强紫外发光峰     

La、Ce掺杂ZnO纳米晶的发光特性

共沉淀法制备了稀土镧、铈掺杂的ZnO半导体纳米晶。X射线衍射(XRD)结果表明:掺杂的ZnO纳米晶为六方纤锌矿结构,随掺杂浓度增加ZnO粒径减小。对铈掺杂纳米ZnO,以波长380nm激发,在443nm处出现了半峰宽较窄的强的蓝光发射峰;镧掺杂ZnO纳米晶则为从418~610nm的多峰宽带发射。     

Li掺杂ZnO纳米棒的导电和发光特性(英文)

利用气相输运方法,在(111)面硅衬底上制备了名义上原子数分数为2%的Li掺杂的ZnO纳米棒(样品A)。作为比较,我们在相同的生长条件下制备了没有任何掺杂的ZnO纳米棒(样品B)。XRD分析测试表明:样品A和样品B中的ZnO纳米棒具有纤锌矿六边形结构,没有其他氧化物,例如Li2O。Hall效应测量表明:样品A导电类型为p型,空穴载流子浓度为6.72×1016cm-3,空穴载流子迁移率为2.46 cm2.V-1.s-1。样品B为n型,电子载流子浓度为7.16×1018cm-3,电子载流子迁移率为4.73 cm2.V-1.s-1。低温光致发光光谱测试表明,样品A和样品B发光峰明显的区别是位于3.351 eV(样品B)和3.364 eV(样品A)处。根据文献报道,在没有掺杂的ZnO中,3.364 eV发光峰源于施主束缚激子发光。通过变温光致发光光谱的测试,证明了在样品A中,位于3.351 eV的发光峰源于受主束缚激子发光,其光学受主能级位于价带顶142meV处。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.