Effect of Mg/Al atom ratio of support on catalytic performance of Co-Mo/MgO-Al2O3 catalyst for water gas shift reaction

Co-Mo-based catalysts supported on mixed oxide supports MgO-Al2O3 with different Mg/Al atom ratios for water gas shift reaction were studied by means of TPR, Raman, XPS and ESR. It was found that the octahedral Mo species in oxidized Co-Mo/MgO(x)-Al2O3 catalyst and the contents of Mo5+, Mo4+, S2- and S2-2 species in the functioning catalysts increased with increasing the Mg/Al atom ratio of the support under the studied experimental conditions. This is favorable for the formation of the active Co-Mo-S phase of the catalysts. Catalytic performance testing results showed that the catalysts Co-Mo/MgO-Al2O3 with the Mg/Al atom ratio of the support in the range of 0.475-0.525 exhibited optimal catalytic activity for the reaction.     

Unusual valences and fast electron exchange in MoFe2O4

The distribution of d electrons over the cations in MoFe₂O₄, which is represented by the formal valence assignment, is shown to be complicated by the equilibrium reactionsFe²⁺_B+Fe³⁺_A+Mo³⁺Fe³⁺_B+Fe²⁺_A+Mo⁴⁺We have used thermal treatment to confirm that the Mo are primarily on octahedral sites; Fe_A[Mo_BFe_B]O₄. K-shell absorption and Mössbauer data at T = 423 K > T_c demonstrate that the iron has an average valence near 2.5+ with fast electron transfer (τ_h < 10⁻⁸ sec) on both octahedral and tetrahedral sites. Paramagnetic susceptibility data give a Curie constant C_M = 7.95 ± 0.2 emu/mole and a Weiss constant θ_p = −445 K; magnetometer measurements confirm a compensation point near 160 K. Transport data give a surprisingly high electronic conductivity, but also give an activated mobility similar to that found in AlFe₂O₄ and CrFe₂O₄ where mixed Fe^3+/2+ valences on both A and B sites have been demonstrated. However, a positive Seebeck coefficient and a preexponential factor one order of magnitude higher in MoFe₂O₄ point to involvement of a fraction of the Mo atoms in electronic transport, which would be consistent with the observation of a τ_h < 10⁻⁸ sec on the A sites of a spinel. An energy diagram consistent with these data and other information about the relative redox potentials of these ions in oxides are proposed for this system.     

Analytical reactions of substituted cyanoferrates : I. Na3[Fe(CN)5(NH3)]

The reagent pentacyanoamminoferrate (PCAF) in its aqueous reactions with some common cations and anions produces colored species in solution. It has been observed that the reactions of Fe³⁺, Fe²⁺, Co²⁺, VO²⁺, Mo⁶⁺, S₂O₃²⁻, and NO₂⁻ are sensitive enough to permit their colorimetric determinations. In addition, the reagent has been found useful in the simultaneous trace analysis of Fe³⁺ and VO²⁺ present in the same solution.A comparative study has been made of the reactions of PCAF and the other unsubstituted cyanoferrates(II) and (III).     

Localized molecular orbitals and the problem of quasi-aromaticity in trinuclear molybdenum cluster compounds with cores of the type [MO3(μ3-X)(μ-Y)3] (X, Y = O, S, n = 4; X = O, Y = Cl, n = 5)

Calculations of localized molecular orbitals (LMO) and their energy levels for the cluster cores [MO₃O₄]⁴⁺, [MO₃SO₃]⁴⁺, [MO₃OS₃]⁴⁺, [Mo₃S₄]⁴⁺ and [MO₃OCl₃]⁵⁺ have been made by the use of energy-localized CNDO/2-LMO. The results of these LMO calculations show that the six-membered closed and continuous π-conjugated systems around the [MO₃Y₃] rings, each of which is formed from three synergically connected three-centered two-electron π bonds, is the most significant feature of the electronic structure for the quasi-aromatic clusters [Mo₃(μ₃-Y)(μ-X)₃]⁴⁺ (X, Y = O, S), and the size and electronegativity of the bridging Y atoms exhibit significant effects on the degree of quasi-aromaticity of these cluster compounds. For the non-aromatic reference cluster [Mo₃OCl₃]⁵⁺, the results of our calculations also show a bonding scheme with only one isolated π bond, thus leading to the loss of quasi-aromaticity; and meanwhile, there is a pair of extra electrons localized on the apical molybdenum atom of the Mo₃ triangle, thus with three Mo---Mo single bonds.     

Electronic structure and molecular properties of the [Mo6X8L6]; X = Cl, Br, I; L = F, Cl, Br, I clusters

Relativistic TDDFT calculations including spin orbit interactions via the ZORA approximation and solvent effects were carried out on the [Mo₆X₈L₆]²⁻ X = Cl, Br, I ; L = F, Cl, Br, I clusters. These calculations indicate that the closely spaced lowest excited states are largely centered on the cubic [Mo₆X₈]⁴⁺ core. Thus, our calculations and the electronic similarities with the strongly luminescent [Mo₆Cl₈Cl₆]²⁻, [Mo₆Br₈Br₆]²⁻ and [Mo₆I₈I₆]²⁻ clusters, suggest that the clusters [Mo₆Cl₈F₆]²⁻, [Mo₆Br₈F₆]²⁻, [Mo₆I₈F₆]²⁻, [Mo₆I₈Cl₆]²⁻ and [Mo₆I₈Br₆]²⁻ studied here might be also luminescent. The calculated bond energies and reactivity indexes indicate that the most labile clusters are those with axial iodide ligands.     

Vapour phase oxidation of 4-methylanisole to anisaldehyde over V2O5 /MgO-Al2O3 catalysts

The vapour phase selective oxidation of 4-methylanisole to anisaldehyde was investigated over different V₂O₅ /MgO-Al₂O₃ catalysts at 673 K and normal atmospheric pressure. Among various catalysts investigated the 16 wt% V₂O₅ /MgO-Al₂O₃ catalyst provided good conversion and product selectivity. The MgO-Al₂O₃ mixed oxide was obtained by a co-precipitation method and V₂O₅ was impregnated from ammonium metavanadate. The MgO-Al₂O₃ support and various V₂O₅ /MgO-Al₂O₃ catalysts were characterized by means of X-ray diffraction, FT-infrared, electron spin resonance, scanning electron microscopy, ammonia and carbon dioxide chemisorption methods. The characterization results suggest that vanadia does not form layer structures on the support surface, instead interacts very strongly with the support, in particular with MgO, and forms amorphous compounds. The NH₃ and CO₂ uptake results provide an interesting information on the acid-base characteristics of these catalysts and correlate with their catalytic properties.     

Carbomolybdate clusters formed by carbonyl insertion into molybdenum-oxygen bonds. Structural investigation of the [RMo4O15X] core (R = ---C9H4O, X = OCH3; R = ---C14H10, X = ---C7H5O2; R = C14H8, X = ---OH)

[C₄H₉)₄N]₂[Mo₂O₇] reacts with a variety of organic species containing α-diketone groups to give tetranuclear complexes of general composition [RMo₄O₁₅X]³⁻. The complexes [(C₄H₉)₄N]₃[(C₉H₄O)Mo₄O₁₅(OCH₃)] (I), [(C₄H₉)₄N]₃[(C₁₄H₁₀)Mo₄O₁₅(C₆H₅CO₂)] (11) and [(C₄H₉)₄N]₃[(C₁₄H₈)Mo₄O₁₅(OH)] (III) were synthesized from the reactions of dimolybdate with ninhydrin, benzil and phenanthraquinone, respectively. Complex II may also be prepared from dimolybdate and benzoin in acetonitrile-methanol solution, from which it co-crystallizes with the binuclear species [(C₄H₉)₄N]₂[Mo₂O₅(C₆H₅C(O)C(O)C₆H₅)₂] · CH₃CN · CH₃OH (IV). Complexes I–III exhibit the tetranuclear core, previously described for the α-glyoxal derivatives [(C₄H₉)₄N]₃[(HCCH)Mo₄O₁₅X], where X = F⁻ or HCO₂⁻. The ligands may be formally described as diketals, formed by insertion of ligand carbonyl subunits into molybdenum-oxygen bonds. The structures I–III differ most dramatically in the identity and coordination mode of the anionic ligand X⁻ which occupies a position opposite the diketal moiety relative to the [Mo₄O₁₁]²⁺ central cage. Thus, I exhibits a doubly bridging methoxy group in this position, while II possesses a benzoate ligand with an unusual μ₃-O,O′coordination mode. Complex III presents a hydroxy-group unsymmetrically bonded to three of the molybdenum centres. The stereochemical consequences of the various coordination modes are discussed. Crystal data: Compound I, monoclinic space group Pc, a = 24.888(2), b = 12.897(3), c = 24.900(3) Å, β = 101.94(2)°, D_calc = 1.28 g cm⁻¹ for Z = 4. Structure solution and refinement based on 8695 reflections with F_o 6σ(F_o) (Mo-K_α, λ = 0.71073 Å) converged at a conventional discrepancy factor of 0.060. Compound II, orthorhombic space group Pbca, a = 20.426(6), b = 26.916(6), c = 32.147(7) Å, V = 17673.2(20) ų, D_calc = 1.33 g cm⁻³ for Z = 8; 5224 reflections, R = 0.076. Compound III, tetragonal space group I4₁/a, a = b = 48.129(6), c = 13.057(2) Å, V = 30246.2(12) ų, D_calc = 1.35 g cm⁻³ for Z = 16; 5554 reflections, R = 0.053. Compound IV, orthorhombic space group Pnca, a = 16.097(4), b = 16.755(4), c = 25.986(7) Å, V = 7008.1(13) ų, Z = 4, D_calc = 1.18 g cm⁻³ ; 2944 reflections, R = 0.061.     

Structural and magnetic properties of the solid solution () YMn1−x(Cu3/4Mo1/4)xO3

Recently, the ferroelectromagnet YMnO₃ has been the focus of interest because it exhibits both antiferromagnetism (Néel temperature 80 K) and ferroelectricity (Curie temperature 914 K). There have been no reports of complete YMn_1−xM_xO₃ solid solutions in which substitution of the foreign M cation preserves the hexagonal P6₃cm structure. In contrast there exist several homeotypic phases with the general formula, Ln_1+nCu_nMO_3+3n (n=1 (M=Ti), 2 (M=V) and 3 (M=Mo); Ln: lanthanide). Several YMn_1−x(Cu_3/4Mo_1/4)_xO₃ compounds have been synthesized. The solid solution, from YMnO₃ (x=0) to YCu_3/4Mo_1/4O₃ (x=1) has been characterized by X-ray diffraction and transmission electron microscopy study. For 0<x<0.9, the compounds are found to crystallize in the non-centrosymmetric structure, space group P6₃cm, of YMnO₃. The Mn-free end member, x=1, crystallizes in a complex multiple cell, the superstructure being associated to Cu³⁺/Mo⁶⁺ cationic ordering. Dilution of the Mn³⁺ magnetic array by the paramagnetic (Cu²⁺) and diamagnetic (Mo⁶⁺) cations is found to decrease the antiferromagnetic ordering temperature and it becomes undetectable for x0.5 compositions.     

Mössbauer studies of thiospinels. V. The systems Cu1−xFexMe2S4 (Me = Cr, Rh) and Cu1−xFexCr2(S0.7Se0.3)4

With the exception of FeRh₂S₄, powder samples of all systems studied have been obtained as spinel phase without essential impurities. The lattice constants follow Vegard's law. From the Seebeck coefficients and the Mössbauer spectra the valence distribution Cu¹⁺_1−xFe²⁺_2x−1Fe³⁺_1−x[Me³⁺₂]X²⁻₄ is derived for 0.5 x 1, while there is only Fe³⁺ present for 0 < x 0.5. Samples with the overall composition FeRh₂S₄ contain mostly Rh₂S₃ and iron sulfide phases, but less than 20% of a spinel phase.     

Study of reduced Mo/Al2O3 metathesis catalysts prepared via metal complexes

The Mo/Al₂O₃ catalysts for propene metathesis were prepared both via anchoring Mo complexes of various nuclearities and by conventional method of impregnation. The catalysts from metal complexes were found to be active in metathesis at ambient temperature after reduction with H₂ or CO at 400–500°C. The average oxidation state of Mo in the activated catalysts was determined with regard to oxygen consumption needed for oxidation of the reduced Mo species to Mo⁶⁺.     

＂Intelligent＂ reforming catalysts： Trace noble metal-doped Ni/Mg（A1）O derived from hydrotalcites

Trace amounts of noble metal-doped Ni/Mg(Al)O catalysts were prepared starting from Mg-Al hydrotalcites (HTs) and tested in daily start-up and shut-down (DSS) operation of steam reforming (SR) of methane or partial oxidation (PO) of propane. Although Ni/Mg(Al)O catalysts prepared from Mg(Ni)-Al HT exhibited high and stable activity in stationary SR, PO and dry reforming of methane and propane, the Ni/Mg(Al)O catalysts were drastically deactivated due to Ni oxidation by steam as purge gas when they were applied in DSS SR ofmethane. Such deactivation was effectively suppressed by doping trace amounts of noble metal on the catalysts by using a “memory effect” of HTs. Moreover, the noble metal-doped Ni/Mg(Al)O catalysts exhibited “intelligent” catalytic behaviors, i.e., self-activation and self-regenerative activity, leading to high and sustainable activity during DSS operation. Pt was the most effective among noble metals tested. The self-activation occurred by the reduction of Ni2+ in Mg(Ni,Al)O periclase to Ni0 assisted by hydrogen spillover from Pt (or Pt-Ni alloy). The self-regenerative activity was accomplished by self-redispersion of active Ni0 particles due to a reversible reductionoxidation movement of Ni between the outside and the inside of the Mg(Al)O periclase crystal; surface Ni0 was oxidized to Ni2+ by steam and incorporated into Mg(Ni2+,Al)O periclase, whereas the Ni2+ in the periclase was reduced to Ni0 by the hydrogen spillover and appeared as the fine Ni0 particles on the catalyst surface. Further a “green” preparation of the Pt/Ni/[Mg3.5Al]O catalysts was accomplished starting from commercial Mg3.5-Al HT by calcination, followed by sequential impregnation of Ni and Pt.     

Determination of sulfur contents of SO3, S2O3 and S based on the electrocatalytic interaction with homogeneous mediator tris(2,2'-bipyridyl)Ru(II)

A sensitive voltammetric method has been developed for the determination of total or single species of sulfur anions containing sulfide, sulfite and thiosulfate. The method is based on the catalytic effect of tris(2,2'-bipyridyl)Ruthenium(II) (Ru(bpy)₂^+ 2) as a homogeneous mediator on the oxidation of those anions at the surface of a glassy carbon electrode. A reversible redox couple of Ru(II)/Ru(III) were observed as a solute in aqueous solution. Cyclic voltammetry study showed that the catalytic current of the system depends on the concentration of the anions. Optimum pH values for voltammetric determination of sulfite, thiosulfate and sulfide has been found to be 5.6, 10.0 and 10.0, respectively. Under the optimized conditions the calibration curves have been obtained linear in the concentration ranges of 0.8–500.0, 0.4–1000.0 and 0.5–5000.0 µmol L^− 1 of SO₃²⁻, S₂O₃²⁻ and S²⁻, respectively. The detection limits have been calculated to be 0.40, 0.17 and 0.33 µmol L^− 1 for SO₃²⁻, S₂O₃²⁻ and S²⁻, respectively. The diffusion coefficients of sulfite and thiosulfate have been estimated using chronoamperometry. The chronoamperometric method also has been used to determine the catalytic rate constant for catalytic reaction of the Ru(bpy)₂^+ 2 with sulfite and thiosulfate. Finally the proposed method has been used for the determination of total sulfur contents in real samples of water and wastewater. Moreover the sulfite content in sugar and sulfur dioxide in air has been determined with satisfactory results.     

Solvothermal synthesis,crystal structure and properties of Mn2(tren)3[Mo2O2S6]2·1.3H2O exhibiting the new polymeric [Mn2(tren)3] n 4+ chain

The novel oxothiomolybdate Mn₂(tren)₃[Mo₂O₂S₆]₂·1.3H₂O [tren = tris(2-aminoethyl)amine], synthesized under solvothermal conditions, consists of one-dimensional novel [Mn₂(tren)₃] _n ⁴⁺ chains and discrete [Mo₂O₂S₆]^2– anions. There are two crystallographically independent chains and four [Mo₂O₂S₆]^2– anions in the asymmetric unit. Each Mn atom in the cationic chains is sixfold coordinated by N atoms of the chelating tren molecules. Two of the four crystallographically independent Mn atoms are tridentately coordinated by two tren molecules, whereas the other two are coordinated tetradentately by one tren molecule and monodentately by the remaining primary amino groups from the tren molecules that act as tridentate ligands. The tren ligand bonding modes lead to the formation of the polymeric [Mn₂(tren)₃] _n ⁴⁺ chain. One of the four Mn atoms is in the unusual trigonal prismatic coordination state with six surrounding N atoms.     

Investigation of vortex dynamics close to Bc2 in Cu2Mo6S8 quasi epitaxial thin films

The Ginzburg number of superconducting Chevrel phases M_xMo₆S₈ with small coherence length (10⁻³ to 10−5) is intermediate between those obtained for conventional low T_c materials (10⁻⁸) and those of high T_c (10⁻¹) indicating that these phases may display features in the dynamics of the vortices similar to those observed in high T_c superconductors. In this work we present a detailed study of I–V measurements close to the B_c2 line carried out on quasi epitaxial thin films of Cu₂Mo₆S₈. The non-linear I–V curves show a scaling behaviour making possible to determine a transition temperature between an unpinned vortex state and a vortex glass state. However, the temperature range of the unpinned vortex state is much wider than expected.     

Influence of d-p π-conjugate interaction upon electronic spectra in some cluster compounds

The UV-vis electronic absorption spectra of the clusters Mo₂S₄(dtp)₂ and Mo₃S₄(dtp)₄·Py have been observed, and the electronic excitation energies have been calculated using the INDO/S-CI method. Comparing the calculated values with the observed results, the absorption bands have been assigned. The influence of d-p π-conjugate interaction strength upon the electronic absorption spectrum is discussed in the clusters Mo₂S₄(dtp)₂ (1), Mo₃S₄(dtp)₄·Py (2), Mo₃O₄(H₂O)₉⁴⁺ (3) and Mo₃S₄(H₂O)₉⁴⁺ (4) [dtp = S₂P(OC₂H₅), Py = pyridine]. It has been found that the absorption bands of clusters 2 and 4, with larger d-p π-conjugate interaction over rings, causes a red-shift compared with those of clusters 1 and 3, with a smaller d-p π-conjugate interaction.     

Carbon Dioxide Reforming of Methane over Ni Catalysts Supported on Al2O3 Modified with La2O3, MgO, and CaO

The preparation of synthesis gas from carbon dioxide reforming of methane (CDR) has attracted increasing attention. The present review mainly focuses on CDR to produce synthesis gas over Ni/MO_x/Al₂O₃ (X = La, Mg, Ca) catalysts. From the examination of various supported nickel catalysts, the promotional effects of La₂O₃, MgO, and CaO have been found. The addition of promoters to Al₂O₃-supported nickel catalysts enhances the catalytic activity as well as stability. The catalytic performance is strongly dependent on the loading amount of promoters. For example, the highest CH₄ and CO₂ conversion were obtained when the ratios of metal M to Al were in the range of 0.04–0.06. In the case of Ni/La₂O₃/Al₂O₃ catalyst, the highest CH₄ conversion (96%) and CO₂ conversion (97%) was achieved with the catalyst (La/Al = 0.05 (atom/atom)). For Ni/CaO/Al₂O₃ catalyst, the catalyst with Ca/Al = 0.04 (atom/atom) exhibited the highest CH₄ conversion (91%) and CO₂ conversion (92%) among the catalysts with various CaO content. Also, Ni/MgO/Al₂O₃ catalyst with Mg/Al = 0.06 (atom/atom) showed the highest CH₄ conversion (89%) and CO₂ conversion (90%) among the catalysts with various Mg/Al ratios. Thus it is most likely that the optimal ratios of M to Al for the highest activities of the catalysts are related to the highly dispersed metal species. In addition, the improved catalytic performance of Al₂O₃-supported nickel catalysts promoted with metal oxides is due to the strong interaction between Ni and metal oxide, the stabilization of metal oxide on Al₂O₃ and the basic property of metal oxide to prevent carbon formation.     

Reactions of M3Te7 (M = Mo, W) clusters with electrophilic reagents: Chalcogen exchange in the Te2 ligand and the first complexes of (TeS)

Reactions of triangular telluride-bridged Mo and W clusters [M₃(μ₃-Te)(μ₂-Te₂)₃(dtp)₃]⁺ (M = Mo, W; dtp = (EtO)₂PS₂) with S₂Cl₂ or Br₂ lead to Te/S exchange in the Te₂ ligands, with the formation of complexes with a novel TeS²⁻ ligand. Reaction of [W₃(μ₃-Te)(μ₂-Te₂)₃(dtp)₃]⁺ with Br₂ or S₂Cl₂ gives a mixture of complexes formulated as [W₃Te_4.25S_2.75(dtp)₃]⁺ and [W₃Te_4.30S_2.70(dtp)₃]⁺, respectively, on the basis of X-ray structural analysis. Reaction of the Mo homolog, namely [Mo₃(μ₃-Te)(μ₂-Te₂)₃(dtp)₃]⁺, with S₂Cl₂ gives rise to [Мо₃Te_4.74S_2.26((EtO)₂PS₂)₃]⁺. Electrospray ionization mass spectrometry (ESI-MS) complements the information gathered from X-ray analysis regarding the degree of Te by S substitution; moreover, detailed insights on the regioselectivity of such replacement are also obtained from ESI-MS analysis. These experimental evidences indicate that Te by S replacement in W complexes display high regioselectivity (as evidenced by the exclusive formation of a W₃Te₄S₃⁴⁺ core), the equatorial Te ligands being preferentially replaced over the Te_ax and μ₃-Te ligands. Conversely, for the Mo homologs, a broad distribution of Mo₃Te_7−xS_x⁴⁺ cluster species ranging from x = 0 to 6 is observed. Bond distance analysis as well as crystal packing trends as a function of the cluster core M₃Te_7−xS_x⁴⁺ (M = Mo, W; x = 0–6) composition are also reported.     

Ab initio molecular orbital study on the gas phase SN2 reaction F + CH3Cl → CH3F + Cl

Ab-initio molecular orbital (MO) and direct ab initio dynamics calculations have been applied to the gas phase S_N2 reaction F⁻ + CH₃Cl → CH₃F + Cl⁻. Several basis sets were examined in order to select the most convenient and best fitted basis set to that of high-quality calculations. The Hartree–Fock (HF) 3−21+G(d) calculation reasonably represents a potential energy surface calculated at the MP2/6−311++G(2df,2pd) level. A direct ab initio dynamics calculation at the HF/3−21+G(d) level was carried out for the S_N2 reaction. A full dimensional ab initio potential energy surface including all degrees of freedom was used in the dynamics calculation. Total energies and gradients were calculated at each time step. Two initial configurations at time zero were examined in the direct dynamics calculations: one is a near collinear collision, and the other is a side-attack collision. It was found that in the near collinear collision almost all total available energy is partitioned into two modes: the relative translational mode between the products (40%) and the C − F stretching mode (60%). The other internal modes of CH₃F were still in the ground state. The lifetimes of the early- and late-complexes F⁻ … CH₃Cl and FCH₃ … Cl⁻ are significantly short enough to dissociate directly to the products. On the other hand, in the side-attack collision, the relative translation energy was about 20% of total available energy.     

A comparative study on the dispersion behaviors and surface acid properties of molybdena on CeO2 and ZrO2 (Tet)

Dispersion of molybdena on CeO₂, ZrO₂ (Tet), and a mixture of CeO₂ and ZrO₂ (Tet), was investigated by using laser Raman spectroscopy (LRS), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and temperature programmed reduction (TPR). The results indicate that molybdena is dispersed on both individual oxide support and mixed oxide support at the adopted molybdena loadings (0.2 and 0.8 mmol Mo⁶⁺/100 m²) and the structure of the supported molybdena species is intimate association with its loading amount. Two molybdena species are identified by Raman results, i.e. isolated MoO²⁻₄ species at 0.2 mmol Mo⁶⁺/100 m² and polymolybdate species at 0.8 mmol Mo⁶⁺/100 m². IR spectra of ammonia adsorption prove that isolated MoO²⁻₄ species are Lewis acid sites on the Mo/Ce and/or Zr samples, and the polymolybdate species are Brönsted acid sites on the Mo/Ce and/or Zr samples. Moreover, a combination of the Raman, IR and TPR results confirms that at 0.2 mmol Mo⁶⁺/100 m² Ce + Zr, molybdena is preferentially dispersed on the surface of CeO₂ when a mixed oxide support (CeO₂ and ZrO₂) is present, which was explained in term of the difference of the surface basicity between CeO₂ and ZrO₂ (Tet). Surface structures of the oxide supports were also taken into consideration.     

Reactions of small negative ions with O2(a Δg) and O2(X Σg)

The rate constants and product ion branching ratios were measured for the reactions of various small negative ions with O₂(X ³Σ_g⁻) and O₂(a ¹Δ_g) in a selected ion flow tube (SIFT). Only NH₂⁻ and CH₃O⁻ were found to react with O₂(X) and both reactions were slow. CH₃O⁻ reacted by hydride transfer, both with and without electron detachment. NH₂⁻ formed both OH⁻, as observed previously, and O₂⁻, the latter via endothermic charge transfer. A temperature study revealed a negative temperature dependence for the former channel and Arrhenius behavior for the endothermic channel, resulting in an overall rate constant with a minimum at 500 K. SF₆⁻, SF₄⁻, SO₃⁻ and CO₃⁻ were found to react with O₂(a ¹Δ_g) with rate constants less than 10⁻¹¹ cm³ s⁻¹. NH₂⁻ reacted rapidly with O₂(a ¹Δ_g) by charge transfer. The reactions of HO₂⁻ and SO₂⁻ proceeded moderately with competition between Penning detachment and charge transfer. SO₂⁻ produced a SO₄⁻ cluster product in 2% of reactions and HO₂⁻ produced O₃⁻ in 13% of the reactions. CH₃O⁻ proceeded essentially at the collision rate by hydride transfer, again both with and without electron detachment. These results show that charge transfer to O₂(a ¹Δ_g) occurs readily if the there are no restrictions on the ion beyond the reaction thermodynamics. The SO₂⁻ and HO₂⁻ reactions with O₂(a) are the only known reactions involving Penning detachment besides the reaction with O₂⁻ studied previously [R.S. Berry, Phys. Chem. Chem. Phys., 7 (2005) 289–290].