Lithium–manganese–nickel-oxide electrodes with integrated layered–spinel structures for lithium batteries

A series of lithium–manganese–nickel-oxide compositions that can be represented in three-component notation, xLi[Mn_1.5Ni_0.5]O₄ · (1 − x){Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂}, in which a spinel component, Li[Mn_1.5Ni_0.5]O₄, and two layered components, Li₂MnO₃ and Li(Mn_0.5Ni_0.5)O₂, are structurally integrated in a highly complex manner, have been evaluated as electrodes in lithium cells for x = 1, 0.75, 0.50, 0.25 and 0. In this series of compounds, which is defined by the Li[Mn_1.5Ni_0.5]O₄–{Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂} tie-line in the Li[Mn_1.5Ni_0.5]O₄–Li₂MnO₃–Li(Mn_0.5Ni_0.5)O₂ phase diagram, the Mn:Ni ratio in the spinel and the combined layered Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂ components is always 3:1. Powder X-ray diffraction patterns of the end members and the electrochemical profiles of cells with these electrodes are consistent with those expected for the spinel Li[Mn_1.5Ni_0.5]O₄ (x = 1) and for ‘composite’ Li₂MnO₃ · Li(Mn_0.5Ni_0.5)O₂ layered electrode structures (x = 0). Electrodes with intermediate values of x exhibit both spinel and layered character and yield extremely high capacities, reaching more than 250 mA h/g with good cycling stability between 2.0 V and 4.95 V vs. Li° at a current rate of 0.1 mA/cm².     

Electrode reactions of manganese oxides for secondary lithium batteries

Nanorods of MnO₂, Mn₃O₄, Mn₂O₃ and MnO are synthesized by hydrothermal reactions and subsequent annealing. It is shown that though different oxides experience distinct phase transition processes in the initial discharge, metallic Mn and Li₂O are the end products of discharge, while MnO is the end product of recharge for all these oxides between 0.0 and 3.0 V vs. Li⁺/Li. Of these 4 manganese oxides, MnO is believed the most promising anode material for lithium ion batteries while MnO₂ is the most promising cathode material for secondary lithium batteries.     

Comments on stabilizing layered manganese oxide electrodes for Li batteries

An electrochemical study of structurally-integrated xLi₂MnO₃•(1 −x)LiMn_0.5Ni_0.5O₂ ‘composite’ materials has been undertaken to investigate the stability of electrochemically-activated electrodes at the Li₂MnO₃-rich end of the Li₂MnO₃–LiMn_0.5Ni_0.5O₂ tie-line, i.e., for 0.7 ≤ x ≤ 0.95. Excellent performance was observed for x = 0.7 in lithium half-cells; comparable to activated electrodes that have significantly lower values of x and are traditionally the preferred materials of choice. Electrodes with higher manganese content (x ≥ 0.8) showed significantly reduced performance. Implications for stabilizing low-cost, manganese-rich, layered lithium-metal-oxide electrode materials are discussed.     

High-energy and high-power Li-rich nickel manganese oxide electrode materials

A lithium-rich nickel-manganese oxide compound Li_x(Ni_0.25Mn_0.75)O_y (x > 1) was synthesized from layered Na_0.9Li_0.3Ni_0.25Mn_0.75O_δ precursor using a lithium ion-exchange reaction. The electrochemical behavior of the material as a cathode for lithium batteries, and a preliminary discussion of its structure are reported. The product Li_1.32Na_0.02Ni_0.25Mn_0.75O_y (IE-LNMO) shows broad X-ray diffraction peaks, but possesses a high intensity sharp (003) layering peak and multiple peaks with intensity in the 20–23° 2θ region which suggest Ni–Mn ordering in the transition metal layer (TM). Li/IE-LNMO cells demonstrate very stable reversible capacities of 220 mAh/g @ 15 mA/g and possess extremely high power of 150 mAh/g @ 1500 mA/g (15C). The Li/IE-LNMO cell dQ/dV plot exhibits three reversible electrochemical processes due to Ni/Mn redox behavior in a layered component, and Mn redox exchange in a spinel component. No alteration in the dQ/dV curves and no detectable change in the voltage profiles over 40 cycles were observed, thus indicating a stable structure for lithium insertion/extraction. This new material is attractive for demanding Li-ion battery applications.     

Enhancing the rate capability of high capacity xLi2MnO3 · (1 − x)LiMO2 (M = Mn,Ni, Co) electrodes by Li–Ni–PO4 treatment

The rate capability of high capacity xLi₂MnO₃ · (1 ? x)LiMO₂ (M = Mn, Ni, Co) electrodes for lithium-ion batteries has been significantly enhanced by stabilizing the electrode surface by reaction with a Li–Ni–PO₄ solution, followed by a heat-treatment step. Reversible capacities of 250 mAh/g at a C/11 rate, 225 mAh/g at C/2 and 200 mAh/g at C/1 have been obtained from 0.5Li₂MnO₃ · 0.5LiNi_0.44Co_0.25Mn_0.31O₂ electrodes between 4.6 and 2.0 V. The data bode well for their implementation in batteries that meet the 40-mile range requirement for plug-in hybrid vehicles.     

Novel concept of pseudocapacitor using stabilized lithium metal powder and non-lithiated metal oxide electrodes in organic electrolyte

A concept of using two non-prelithiated metal oxides (e.g., MnO₂, V₂O₅, and FeO_x) in both positive and negative electrodes in organic Li-ion electrolytes has been proposed and tested to improve the energy density of pseudocapacitors. To take the advantages of this concept, additional lithium source is essential to provide lithium ions during the charge–discharge cycles. The stabilized lithium metal powder (SLMP^?) developed by FMC Corp., provides such an essential Li⁺ source. Here we report the first result of the symmetric pseudocapacitor using two non-prelithiated metal oxide (i.e., manganese oxide/carbon nanotube (MnO₂/CNT)) electrodes, with added SLMP in one of them. The capacitor using the SLMP added MnO₂/CNT (positive) and pure MnO₂/CNT (negative) electrode in 1.2 M LiPF₆-EC:EMC electrolyte shows supercapacitive behaviors in 3.0 V voltage range. The addition of SLMP opens new opportunities of using the non-lithiated metal oxide electrodes in pseudocapacitors and hybrid electrochemical capacitors (ECs), which has not been possible before.     

Comparison of the electrochemical properties of metallic layered nitrides containing cobalt,nickel and copper in the 1 V–0.02 V potential range

We report the first example of an intercalation compound based on the nitrogen framework in which lithium can be intercalated and deintercalated. A comparison of the structural and electrochemical properties of the ternary lithium cobalt, nickel and copper nitrides is performed. Vacancy layered structures of ternary lithium nitridocobaltates Li_3−2xCo_xN and nitridonickelates Li_3−2xNi_xN with 0.10 ⩽ x ⩽ 0.44 and 0.20 ⩽ x ⩽ 0.60, respectively, are proved to reversibly intercalate Li ions in the 1 V–0.02 V potential range. These host lattices can accommodate up to 0.35 Li ion par mole of nitride. Results herein obtained support Li insertion in vacancies located in Li₂N⁻ layers while interlayer divalent cobalt and nickel cations are reduced to monovalent species. No structural strain is induced by the insertion–extraction electrochemical reaction which explains the high stability of the capacity in both cases. For the Li_1.86Ni_0.57N compound, a stable faradaic yield of 0.30 F/mol, i.e. 130 mAh/g, is maintained at least for 100 cycles. Conversely, the ternary copper nitrides corresponding to the chemical composition Li_3−xCu_xN with 0.10 ⩽ x ⩽ 0.40 do not allow the insertion reaction to take place due to the presence of monovalent copper combined with the lack of vacancies to accommodate Li ions. In the latter case, the discharge of the lithium copper nitrides is not reversible.     

Preparation of Mn-substituted LiFeO2: A solid solution of LiFeO2 and LixMnO2

A new type of LiFeO₂–Li_xMnO₂ solid solution was synthesized at 350 °C under argon flow by a solid-state reaction. The doped Mn ions in the LiMn_xFe_1−xO₂ (0<x⩽0.5) obtained at 150 °C were regarded as an impurity in the orthorhombic LiFeO₂ structure and failed to form a perfect substitution form due to the low synthesis temperature. However, the LiFeO₂–Li_xMnO₂ solid solutions with various Mn contents (Mn/(Fe + Mn)=0.1–0.5) were successfully obtained by calcination at 350 °C. Especially, the XRD pattern of the 50% Mn-substituted LiFeO₂ material was very similar to that of a lithiated Li_xMnO₂ compound. The Li/50% Mn-substituted LiFeO₂ cell exhibited not only a distinct increased voltage plateau in the 2.8 V region, but also an excellent cycling performance upto 50 cycles. We believe that this LiFeO₂–Li_xMnO₂ solid solution type compound has a unique electrochemical property in the cycling process.     

Electrochemical properties of Li(Li(1−x)/3CoxMn(2−2x)/3)O2 (0 ⩽ x ⩽ 1) solid solutions prepared by poly-vinyl alcohol (PVA) method

The whole range of solid solutions Li(Li_(1−x)/3Co_xMn_(2−2x)/3)O₂ (0 ⩽ x ⩽ 1) was firstly synthesized by an aqueous solution method using poly-vinyl alcohol as a synthetic agent to investigate their structure and electrochemical properties. X-ray diffraction results indicated that the synthesized solid solutions showed a single phase without any detectable impurity phase and have a hexagonal structure with some additional peaks caused by monoclinic distortion, especially in the solid solutions with a low Co amount. In the electrochemical examination, the solid solutions in the range between 0.2 ⩽ x ⩽ 0.9 showed higher discharge capacity and better cyclability than LiCoO₂ (x = 1) on cycling between 2.0 and 4.6 V with 100 mA g⁻¹ at 25 °C. For example, Li(Li_0.2Co_0.4Mn_0.4)O₂ (x = 0.4) exhibited a high discharge capacity of 180 mA h g⁻¹ at the 50th cycle. By synthesizing the solid solution between Li₂MnO₃ and LiCoO₂, the electrochemical properties of the end members were improved.     

Anomalous capacity and cycling stability of xLi2MnO3 · (1 − x)LiMO2 electrodes (M = Mn,Ni, Co) in lithium batteries at 50 °C

Transition metal oxides with composite xLi₂MnO₃ ·  (1 − x)LiMO₂ rocksalt structures (M = Mn, Ni, Co) are of interest as a new generation of cathode materials for high energy density lithium-ion batteries. After electrochemical activation to 4.6 or 4.8 V (vs. Li⁰) at 50 °C, xLi₂MnO₃ · (1 − x)LiMn_0.33Ni_0.33Co_0.33O₂ (x = 0.5, 0.7) electrodes deliver initial discharge capacities (>300 mAh/g) at a low current rate (0.05 mA/cm²) that exceed the theoretical values for lithiation back to the rocksalt stoichiometry (240–260 mAh/g), at least during the early charge/discharge cycles of the cells. Attention is drawn to previous reports of similar, but unaccounted and unexplained anomalous behavior of these types of electrode materials. Possible reasons for this anomalous capacity are suggested. Indications are that electrodes in which M = Mn, Ni and Co do not cycle with the same stability at 50 °C as those without cobalt.     

LiMn2O4 hollow nanosphere electrode material with excellent cycling reversibility and rate capability

Lithium-rich Li_1.05Mn₂O₄ hollow nanospheres have been successfully prepared by air-calcining lithiated MnO₂ precursor at a low temperature of 550 °C, which was synthesized by chemical lithiation of hollow MnO₂ nanospheres with LiI at 70 °C for 12 h. The lithium-rich Li_1.05Mn₂O₄ hollow nanospheres exhibit an excellent cycling stability and rate capability as a cathode material for rechargeable lithium batteries: it maintains 90% of its initial capacity after 500 cycles, and keeps 70% of the reversible capacity at 0.1 C rat, even at 15 C rate.     

Coordination polymers incorporating copper(II) and manganese(II) centers bridged by pyridinedicarboxylate ligands: Structure and magnetism

Two heterobimetallic coordination polymers, [Cu(2,4-pydc)₂Mn(H₂O)₄]_x (1) and [Cu(2,5-pydc)₂Mn(H₂O)₂]_x · 4xH₂O (2), have been synthesized and structurally characterized by single crystal X-ray diffraction. Both compounds have extended 2-D sheet structures. In 1 the copper centers are linked in chains by double ligand bridges and these chains are cross-linked through the manganese coordination spheres and O–C–O bridges to form polymeric sheets. In 2 separate O–C–O bridged Cu and Mn chains are connected in an alternating array by additional ligand bridging to generate the overall 2-D structure. Analysis of magnetic data of 1 reveals that ferromagnetic exchange between the O–C–O bridged copper and manganese centers dominates the magnetic properties of this system. The magnetic data for 2 fit well to a model incorporating antiferromagnetic exchange in independent S = 1/2 and S = 5/2 linear chains with J(Cu) = −0.073 cm⁻¹ and J(Mn) = −0.32 cm⁻¹. Unlike the situation in 1, there is no evidence for heterometallic exchange. In both 1 and 2 the significant exchange occurs via O–C–O bridges. To study the effect of thermal dehydration on the magnetic properties of these systems, the compounds Cu(2,4-pydc)₂Mn · H₂O (1d) and Cu(2,5-pydc)₂Mn · H₂O (2d) were synthesized and studied.     

Conversion of porous PbO2 layers through galvanic displacement reaction with Mn2 + ions

The galvanic exchange between Mn^2 + ions and electrodeposited porous PbO₂ was studied to produce a porous oxide whose lower conductivity prevented its direct oxygen bubble-templated anodic deposition. Immersion of PbO₂ layers in acid acetate solutions of Mn^2 + led to the formation of amorphous MnO_x shell onto PbO₂. Due to its amorphous nature, MnO_x could not be proved to be MnO₂ by XRD. However, MnO_x was cathodically stripped at the same potential as MnO₂. The deposition of the MnO_x shell onto PbO₂ enhanced the capacity of the porous electrodes.     

High capacity Li[Li0.2Mn0.54Ni0.13Co0.13]O2–V2O5 composite cathodes with low irreversible capacity loss for lithium ion batteries

With an aim to suppress the huge irreversible capacity loss encountered in high capacity layered oxide solid solutions between Li₂MnO₃ and LiMO₂ (M = Mn, Ni, and Co), layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with various V₂O₅ contents have been investigated. The irreversible capacity loss decreases from 68 mAh/g at 100% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ to 0 mAh/g around 89 wt.% Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–11 wt.% V₂O₅ as the lithium-free V₂O₅ serves as an insertion host to accommodate the lithium ions that could not be inserted back into the layered lattice after the first charge. The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂–V₂O₅ composite cathodes with about 10–12 wt.% V₂O₅ exhibit an attractive discharge capacity of close to 300 mAh/g with little irreversible capacity loss and good cyclability.     

XAFS characterization of La1−xSrxMnO3±δ catalysts prepared by Pechini’s method

XAFS experiments at the Mn and Sr K-edges were carried out in order to investigate the short-range arrangement of Mn and Sr sites on La_1−xSr_xMnO_3±δ highly doped perovskites (x = 0, 0.2, 0.4 and 0.6). The Mn K-edge EXAFS spectra show a static Jahn–Teller distortion of the MnO₆ for x = 0 and 0.2, which is drastically reduced as x increases. The distortion of perovskite, characterized by the Mn–O–Mn tilt angle, progressively decreases with increasing Sr contents. Sr K-edge results indicated a decrease on the Sr–Mn coordination number upon Sr doping. Based on this and TPD results, a charge compensating mechanism is proposed suggesting a partial Mn oxidation and formation of Mn defect vacancies due to the introduction of Sr.     

Pulse deposition of large area,patterned manganese oxide nanowires in variable aspect ratios without templates

Manganese oxide nanowires with β-MnOOH in core and Mn₃O₄ in shell were successfully plated onto various conductive substrates from a Mn(CH₃COO)₂ solution by anodic deposition under a two-electrode, pulse-rest mode. The aspect ratio of uniform nanowire morphologies in cm² scale is controllable by varying the deposition variables. Patterned MnO_x nanowire arrays were obtained by combining lithographic and electroplating techniques demonstrated to be a powerful method for preparing MnO_x nanowires in the field emission (FE) array cathodes with a low turn-on voltage (∼3.4 V/μm at 1 μA/cm²).     

Structural and optical properties of sprayed Zn1−xMnxO films

In recent years the dilute magnetic semiconductors have received much attention due to the complementary properties of semiconductor and ferromagnetic behaviour. Zn_1−xMn_xO thin films have been synthesized by chemical spray pyrolysis at a substrate temperature of 400 °C with different manganese compositions that vary in the range, 0.0 ≤ x ≤ 0.25, on Corning 7059 glass substrates. The X-ray diffraction studies revealed that all the films were strongly oriented along the (002) orientation corresponding to the hexagonal wurtzite structure. The crystalline quality of the layers was found to decrease with the increase of x, however, no structural changes were observed over the ‘Mn’ composition range investigated. The optical absorption studies revealed that the energy band gap of the films followed the Vegard's law. The optical band gap of the films prepared at x = 0.15 was found to be ∼3.35 eV. The photoluminescence characteristics of Zn_1−xMn_xO films showed an emission peak at around 390 nm with a broad band about 530 nm. The details of these results were reported and discussed.     

A convenient MnIII starting material for the synthesis of homo- and heterometallic manganese carboxylate clusters: Mn9 and Mn10−xFex complexes

The use of a convenient source of Mn^III ions, namely the [Mn(OR)(O₂CR′)₂]_n (R = H, Me, and R′ = Me, Bu^t) family of 1-D coordination polymers, afforded two new enneanuclear and decanuclear molecular clusters, homometallic [Mn₉O₇(O₂CBu^t)₁₃(MeCN)₂] (3) and heterometallic [Mn_10?xFe_x(OMe)₂₀(O₂CMe)₁₀] (x < 10) (4), respectively. Compound 3 was synthesized by a solvent-induced structural transformation, whereas complex 4 resulted from the reaction of [Mn(OH)(O₂CMe)₂]_n with an Fe^III source. The core of 3 comprises two [Mn₄O₂]⁸⁺ butterfly units and a [Mn₃O]⁷⁺ triangular unit fused together by sharing one Mn atom. Magnetic susceptibility measurements of 3 revealed dominant antiferromagnetic interactions within the molecule, and a ground state of S = 1 with many low-lying excited states. Complex 4 is a mixed Fe^III/Mn^III single-strand molecular wheel, which forms 3D nanotubular stacks arranged in a zig–zag fashion. The described work suggests that the [Mn(OR)(O₂CR′)₂]_n compounds represent excellent starting materials for Mn^III carboxylate cluster chemistry.     

Tunable lithium storage properties of metal lithium titanates by stoichiometric modulation

A simple stoichiometric modulation of Na_2 − 2xSr_xLi₂Ti₆O₁₄ was developed to achieve tunable electrochemical properties of the material. The concept was confirmed experimentally and theoretically using density functional theory (DFT) calculations. Both the operating potential and the amount of reversibly intercalated lithium ions were manipulated by simply changing the Na/Sr ratio. These unique characteristics originated from a gradual change in the electron density on the Ti atoms and the extra lithium insertion sites at SrLi₂Ti₆O₁₄. As a promising anode material for lithium-ion batteries, Na_2 − 2xSr_xLi₂Ti₆O₁₄ and its tunable electrochemical properties have significant importance in terms of the development of tailored electrodes with desirable electrochemical performance.     

XPS/EXAFS study of cycleability improved LiMn2O4 thin film cathodes prepared by solution deposition

The influence of Sn substitution in LiMn₂O₄ thin films as a cathode has been studied via solution deposition to improve the electrochemical performance of thin film lithium batteries. LiSn_0.025Mn_1.95O₄ thin films showed the most promising performance, i.e. a high capacity retention of 77% at 10 C after the 500th cycle, due to the increased average Mn valence state. The thin films of LiSn_x/2Mn_2?xO₄ (x ? 0.10) showed significant precipitation of SnO₂ and SnO after the cycling evaluation.