Determination of lead in fine particulates by slurry sampling electrothermal atomic absorption spectrometry

A simple method for determining lead in fine particulates (PM2.5) by using electrothermal atomic absorption spectrometry (ETAAS) has been developed. Particulates collected on Nuclepore filter by using a dichotomous sampler were suspended in diluted nitric acid after ultrasonic agitation. The dislodging efficiency is nearly 100% after agitation for 5 min. In order to study the suspension behavior of PM2.5 in solvents, a Brookhaven ZetaPlus Particle Size Analyzer was used to determine the particle size distribution and suspension behavior of air particulates in the solvent. The pre-digestion and modification effect of nitric acid would be discussed. Palladium was added as a chemical modifier and the temperature program of ETAAS was changed in order to improve the recovery. The slurry was introduced directly into a graphite tube for atomization. The metal content in the sample was determined by the standard addition method. In addition, a conventional acid digestion procedure was applied to verify the efficiency of the slurry sampling method. It offers a quick and efficient alternative method for heavy metal characterization in fine particulates.     

ETAAS determination of Cd and Pb in plants

Simple and rapid analytical procedures for the ETAAS determination of Cd and Pb in plant (poplar, clover, plantain) leaves are described. Optimal conditions are presented for the wet digestion of plant matrices with a mixture of nitric acid and hydrogen peroxide along with optimal temperature programmes for subsequent modifier-free electrothermal determination of Cd and Pb. Slurry preparation procedures using tetramethylammonium hydroxide or a mixture of 1 mol/L HNO₃ + 1.5 mol/L H₂O₂ are proposed as another approach for rapid and accurate routine analysis of Cd and Pb in plant leaves. It has been found that single standard addition can be used for quantitative determination in the case of wet digestion ETAAS and standard addition to each analysed matrix is recommended in the case of slurry ETAAS. For all plant leaves investigated good agreement was achieved between the concentrations determined by wet digestion ETAAS and slurry ETAAS. The wet digestion method provides relative standard deviations for Cd ranging from 3% to 17% and for Pb from 2% to 16%. For the slurry method the RSD values are in the range of 4–31% for Cd and 4–30% for Pb, depending for both cases on the magnitude of the measured concentrations. Validity and versatility of the methods are verified by the analyses of standard reference materials. Received: 17 March 1997 / Revised: 2 May 1997 / Accepted: 8 May 1997     

Size-fractionated airborne particulate matter characterization of a residential area near Islamabad airport by IBA methods

Size fractionated PM_2.5 and PM_2.5?C10 airborne particulates collected from the airport housing society site in Rawalpindi were characterized using the non destructive ion beam analysis method. Proton induced X-ray emission and Proton induced gamma ray emission were employed to quantify 28 trace elements in fine and coarse filter samples. The average PM_2.5 and PM_2.5?C10 masses were found to be 15.7 and 144???g/m³, respectively which, when combined exceed the Pakistani limit for PM₁₀ of 100???g/m³. The average black carbon (BC) content was found to be 3.49 and 5.95???g/m³ corresponding to 23.8 and 4.30% of the fine and coarse masses, respectively. The reconstructed mass (RCM) was calculated for both particle modes using 5 pseudo sources, namely soil, sulfate, smoke, sea salt and BC. It was found that 5 sources could account for 80.6 and 49.0% of the fine and coarse masses, respectively. The low value of RCM for the coarse mode may imply a much higher organic content. The major sources contributing to the fine mode were soil, sulfate and BC. Similarly for the coarse mass fraction it was found that soil was the major source whereas the sulfate and BC sources did not contribute as much.     

Chemical characterization of particulate matter suspended in the atmosphere by energy dispersive X-ray fluorescence (EDXRF)

Summary This paper presents the first measurement of the elemental composition of the suspended particulate matter in the atmosphere of Londrina city (Paraná State, Brazil). The sampling was accomplished in the summer of 2003 and in the winter of 2002, with a stacker filter holder, collecting simultaneously the fine particulates (PM_2.5) and the coarse particulates (PM₁₀). The concentration of K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Br and Pb associated with particulate matter was determined by energy dispersive X-ray fluorescence. The results of the grouping analysis suggested that the elements in the aerosol particles came from two sources: soil re-suspension and industrial or anthropogenic activities.     

Local and non-local sources of airborne particulate pollution at Beijing

A new element tracer technique has firstly been established to estimate the contributions of mineral aerosols from both inside and outside Beijing. The ratio of Mg/Al in aerosol is a feasible element tracer to distinguish between the sources of inside and outside Beijing. Mineral aerosol, inorganic pollution aerosol mainly as sulfate and nitrate, and organic aerosol are the major components of airborne particulates in Beijing, of which mineral aerosol accounted for 32%–-67% of total suspended particles (TSP), 10% –70% of fine particles (PM2.5), and as high as 74% and 90% of TSP and PM_2.5, respectively, in dust storm. The sources from outside Beijing contributed 62% (38%–-86%) of the total mineral aerosols in TSP, 69% (52%–-90%) in PM₁₀, and 76% (59%–-93%) in PM_2.5 in spring, and 69% (52%–-83%), 79% (52%–-93%), and 45% (7% – 79%) in TSP, PM₁₀, and PM_2.5, respectively, in winter, while only ≈20% in summer and autumn. The sources from outside Beijing contributed as high as 97% during dust storm and were the dominant source of airborne particulates in Beijing. The contributions from outside Beijing in spring and winter are higher than those in summer, indicating clearly that it was related to the various meteorological factors.     

Determination of Cd, Co, Cr, Cu, Fe, Ni and Pb in Milk, Cheese and Chocolate

 Combined analytical procedures consisting of wet digestion step followed by instrumental determination – differential pulse cathodic stripping voltammetry (DPCSV) or electrothermal atomic absorption spectrometry (ETAAS) – as well as a direct analysis method – slurry sampling ETAAS – for the determination of Cd, Co, Cr, Cu, Fe, Ni and Pb in milk, cheese and chocolate are described and compared. Wet digestion using a mixture of HNO₃-HClO₄-H₂O₂ is proposed for complete matrix decomposition prior to trace analyte determinati on by DPCSV or ETAAS. A mixture of HNO₃-H₂O₂ is used for slurry preparation. Optimal instrumental parameters for trace analyte measurements are presented. The reliability of the procedures has been verified by analyzing standard reference materials. Results obtained are in good agreement with the certified values and the relative standard deviations (for these results) are in the range 5–10% for wet digestion DPCSV or ETAAS and 3–9% for slurry sampling ETAAS in the range of 2 μgċg⁻¹ (Cd) to 12 μgċg⁻¹ (Fe). Received August 24, 1999. Revision January 20, 2000.     

Direct determination of cadmium in calcium drug samples using electrothermal atomic absorption spectrometry with a metal tube atomizer and thiourea as a matrix modifier

A laboratory constructed molybdenum tube atomizer was used for direct determination of trace cadmium in drug samples by the electrothermal atomic absorption spectrometric (ETAAS) method. An ultrasonic agitation method for a solution including the sample powder was used. A calibration curve was constructed with a cadmium standard solution including matrix. To eliminate interference from other matrix elements, a chemical modifier thiourea, was used. The detection limit were 17 pg ml(-1) (3 S/N), and the RSD of the direct analysis was 5-17%. The results for cadmium in the four drug samples analysed by the direct ETAAS method matched well with those obtained with nitric acid digested samples. The recovery of added cadmium was 103-106%. An accurate method is elaborated for the determination of cadmium in drug samples by direct ETAAS techniques. The merits of this method are rapid calibration, simplicity, fast analysis, and low cost.     

Extraction of arsenic species from airborne particulate filters—Application to an industrial area of Greece

In the present study, the extraction of the arsenic species arsenite (As(III)), arsenate (As(V)), monomethyarsonic (MMA) and dimethylarsinic acid (DMA) from airborne particulate filters was investigated and optimized. For this purpose, total suspended particulate matter as well as size fractionated aerosol samples were collected from the industrial area of Aspropyrgos, Greece, in glass fibre and polycarbonated filters, respectively. Among H₃PO₄ and HCl, tested in various concentrations, concentrated HCl was found to be the most effective extractant for arsenic from both polycarbonated and glass fibre filters, without provoking any arsenic species transformation. However, the quantitative extraction of arsenic species from glass fibre filters required the subsequent washing of the filters with ultrapure water after their leaching with concentrated HCl. The developed procedure was applied to airborne particulate filters for arsenic speciation in Aspropyrgos' atmosphere. The results showed an enrichment of As in the fine (PM_2.5) compared with the coarse (PM_10–2.5) fraction of airborne particulates, while As(V) was found to be the predominant arsenic species in all samples. Finally, As concentration in the PM₁₀ fraction, for the investigated area and time period from December 2004 to June 2006, was below the target value of 6 ng As m^− 3, referred in the Directive 2004/107 of European Union.     

Elemental concentrations of aerosols near Portuguese power plants by INAA and PIXE

Mass and elemental concentrations in PM₁₀ and PM_2.5 — airborne particulate matter with an aerodynamic diameter below 10 μm and 2.5 μm, respectively — have been evaluated in mainland Portugal since 1993. The data herein refer to areas generally impacted by emissions from electrical power plants, either coal- or oil-fired, which are mostly large, state-of-the-art facilities. Background areas have been sampled as well, and results from one of them are given for comparison. Through the country, lead levels are well below the European enacted values, particularly since unleaded fuels became mandatory in the late 1990s. Nickel appears especially concentrated in PM_2.5 and, apart from extreme cases (rural sites, coal-fired plants), its levels are not significantly different from place to place. Highest values for arsenic and mercury have been found in the vicinity of the coal-fired plants. Cadmium data, if only available for metropolitan Lisbon, seems to confirm the trend for anthropogenic elements appearing mainly in fine particulates.     

On the effect of catalyst status in the quantitative determination of platinum in Pt-Sn/MgO materials

The development of an analytical method for the determination of platinum in MgO based Pt/Sn catalysts is described. Electrothermal atomic absorption spectroscopy (ETAAS) was chosen because of its high sensitivity and robustness against spectral interferences. All the sources of chemical interferences were statistically analyzed and corrections were adopted for the presence of magnesium oxide support. The effectiveness of different mineralization procedures was critically evaluated as a function of the chemical of the solid catalyst. Microwave digestion allowed recovery of metal of 100% for all the catalysts analyzed and exhibited significant better precision values than other digestion methods, which could nevertheless be utilized under proper conditions in selected cases. Received: 31 July 2000 / Revised: 17 October 2000 / Accepted: 24 October 2000     

Determination of lead in waters and sediments from the wetland Tablas de Daimiel National Park (Spain)

Electrothermal atomic absorption spectrometry (ETAAS) has been used for lead control in waters and sediments of the wetland Tablas de Daimiel National Park. The lead determination in the wetland water is hindered by an enhanced salt content, so matrix interference was evaluated. The use of stabilized temperature platform atomization technique, Zeeman background correction and palladium nitrate as matrix modifier were found advisable. For the sediments a closed-vessel microwave dissolution method has been proposed using a mixture of HCl-HNO₃-HF and a heating time of 90 s. With subsequent ETAAS using platform atomization and Zeeman background correction, no chemical modification was necessary. Using these conditions, the interferences were completely removed for both waters and sediments and the calibration curve in ultrapure water (1% nitric acid) was linear up to 30 μg/L. The detection limits for waters and sediments were 0.95 μg/L and 0.78 μg/g, respectively. The accuracy of the proposed method for sediments was validated by analyzing certified reference materials (obtained values were within the certified ones) and spiked wetland sediments (mean recovery of 99.0%). Received: 11 October 1998 / Revised: 3 December 1998 / Accepted: 11 March 1999     

Development of a slurry-extraction procedure for direct determination of cobalt by electrothermal atomic absorption spectrometry in complex environmental samples

A new procedure for Co determination in a complex matrix (coal fly ash) by slurry extraction-electrothermal atomic absorption spectrometry (ETAAS) is presented. Fractional experimental designs were applied to find the most important variables affecting Co extraction. Two liquid media (HCl + HNO₃ and HF) and three agitation modes (ultrasonic probe, ultrasonic bath and manual shaking) were assayed. HF revealed as the most suitable medium for Co extraction, being its concentration and time of contact the most significant variables. Quantitative extraction was obtained after their optimisation (16%, v/v HF; 5 min), with good accuracy (coal fly ash SRM 1633a and SRM 1633b) and precision (R.S.D. < 11.5%). The limit of detection of the method was 0.02 μg g⁻¹ (100 mg mL⁻¹ slurry), and the characteristic mass was 15 ± 1 pg. The ‘slurry-extraction procedure’ established is simple, fast, cheap and was also validated for soil and sediment analysis. As far as we know, a slurry-extraction procedure has not yet been applied to quantify cobalt by ETAAS in such matrices. Moreover, nine coal fly ashes, 12 sediments and 18 soils were analysed by the proposed method and also by a direct slurry sampling-ETAAS procedure in order to compare their performance. In general, the HF-extraction slurry procedure revealed superior.     

Slurry sampling electrothermal atomic absorption spectrometry for trace element analysis of high-purity tungsten trioxide

A slurry sampling ETAAS method for the determination of trace concentrations of Ca, Co, Cr, Cu, Fe, K, Mg, Na and Ni in tungsten trioxide is presented. A high background absorption appearing with large sample amounts during atomization at high temperatures was the only matrix interference observed. It could be significantly reduced by volatilization of the matrix in the pyrolysis step. Calibration curves recorded with aqueous standards could be used for calibration in all cases excluding the determination of very low analyte concentrations of Co and Fe which required the use of the standard additions method. The results obtained by this method showed an excellent agreement with those determined in digests by ETAAS. The detection limits achievable by the slurry technique were between 1 (Ca, K, Mg, Na) and 210 (Cu) ng/g. They were mostly by more than one order of magnitude better than those of the solution techniques. Received: 9 July 1997 / Revised: 6 October 1997 / Accepted: 10 October 1997     

Preconcentration of gallium by coprecipitation with synthetic zeolites prior to determination by electrothermal atomic absorption spectrometry.

Synthetic zeolites were dissolved in nitric acid, and the resulting solution used as a coprecipitant for the preconcentration of trace amounts of gallium in water samples prior to determination by electrothermal atomic absorption spectrometry (ETAAS). The gallium preconcentration conditions and the ETAAS measurement conditions were optimized. Gallium was quantitatively concentrated with the zeolites coprecipitate from pH 6.0 to 8.0. The coprecipitate was easily dissolved in nitric acid, and an aliquot of the resulting solution was introduced directly into a tungsten metal furnace. The atomic absorbance of gallium in the resulting solution was measured by ETAAS. An ashing temperature of 400 degrees C and an atomizing temperature of 2600 degrees C were selected. The calibration curve was linear up to 3.0 microg of gallium and passed through the origin. The detection limit (S/N > or = 3) for gallium was 0.08 microg/100 cm3. The relative standard deviation at 1.0 microg/100 cm3 was 3.0% (n = 5). The proposed method has been successfully applied to trace gallium analysis in environmental water samples.     

Microwave digestion and matrix separation for the determination of cadmium in urine samples by electrothermal atomization atomic absorption spectrometry using a fast temperature program

 A method is proposed which involves sample pretreatment followed by electrothermal atomic absorption spectrometry (ETAAS) for determination of cadmium in human urine. A microwave digestion system was devised to accommodate double-closed vessels for simultaneous digestion of batches of up to 24 urine samples in about 20 min. After digestion, matrix substances which might interfere were removed using silica-immobilized 8-hydroxyquinoline (I-8HOQ) columns. The analyte adsorbed on the column was then eluted with dilute nitric acid solution and determined by ETAAS using a fast temperature program. Neither ashing steps in the furnace heating program nor use of matrix modifiers was necessary. The accuracy, precision, limit of detection, and sample throughput of the method were evaluated. With meticulous control of systematic errors which may be introduced in the pretreatment procedures, the present method can serve as a reference technique for the analysis of Cd in urine samples. Received: 29 July 1996/Revised: 30 September 1996/Accepted: 13 October 1996     

Microwave digestion and matrix separation for the determination of cadmium in urine samples by electrothermal atomization atomic absorption spectrometry using a fast temperature program

 A method is proposed which involves sample pretreatment followed by electrothermal atomic absorption spectrometry (ETAAS) for determination of cadmium in human urine. A microwave digestion system was devised to accommodate double-closed vessels for simultaneous digestion of batches of up to 24 urine samples in about 20 min. After digestion, matrix substances which might interfere were removed using silica-immobilized 8-hydroxyquinoline (I-8HOQ) columns. The analyte adsorbed on the column was then eluted with dilute nitric acid solution and determined by ETAAS using a fast temperature program. Neither ashing steps in the furnace heating program nor use of matrix modifiers was necessary. The accuracy, precision, limit of detection, and sample throughput of the method were evaluated. With meticulous control of systematic errors which may be introduced in the pretreatment procedures, the present method can serve as a reference technique for the analysis of Cd in urine samples. Received: 29 July 1996/Revised: 30 September 1996/Accepted: 13 October 1996     

Determination of lead in waters and sediments from the wetland Tablas de Daimiel National Park (Spain)

Electrothermal atomic absorption spectrometry (ETAAS) has been used for lead control in waters and sediments of the wetland Tablas de Daimiel National Park. The lead determination in the wetland water is hindered by an enhanced salt content, so matrix interference was evaluated. The use of stabilized temperature platform atomization technique, Zeeman background correction and palladium nitrate as matrix modifier were found advisable. For the sediments a closed-vessel microwave dissolution method has been proposed using a mixture of HCl-HNO₃-HF and a heating time of 90 s. With subsequent ETAAS using platform atomization and Zeeman background correction, no chemical modification was necessary. Using these conditions, the interferences were completely removed for both waters and sediments and the calibration curve in ultrapure water (1% nitric acid) was linear up to 30 μg/L. The detection limits for waters and sediments were 0.95 μg/L and 0.78 μg/g, respectively. The accuracy of the proposed method for sediments was validated by analyzing certified reference materials (obtained values were within the certified ones) and spiked wetland sediments (mean recovery of 99.0%). Received: 11 October 1998 / Revised: 3 December 1998 / Accepted: 11 March 1999     

Neutron activation analysis for identification of African mineral dust transport

A Gent stacked filter unit sampler was used to collect air particulate matter (APM) in separate coarse (PM_2.5–10) and fine (PM_2.5) size fractions, at a sub-urban site in Lisbon, Portugal. The sampling was done during the year 2001 and two daily samples were taken per week. The filters were analyzed for particulate mass by instrumental neutron activation analysis (INAA). The chemical analysis of APM levels and the study of the atmospheric dynamics by back-trajectories showed that most of the PM_2.5 and PM_2.5–10 peaks events were associated with air masses transport from the Saharan desert. High mineral load in ambient particulate matter levels were registered during the Saharan dust outbreaks. The accuracy of INAA to measure Fe, Sc and Sm was evaluated by NIST filter standards, revealing results with an agreement of ± 10%. This method constituted an important tool to identify these events.     

Determination of tin by resin-suspension electrothermal atomic absorption spectrometry after enrichment as the complex with ammonium pyrrolidinedithiocarbamate.

A resin-phase extraction method has been optimized for the trace determination of tin(II) by ETAAS. Tin(II) was extracted on a finely divided anion exchange resin as the complex with ammonium pyrrolidinedithiocarbamate (APDC). The resin was collected on a membrane filter and then dispersed in 1.00 ml of 1 mol l(-1) nitric acid containing 100 microg of Pd(II) and 60 microg of Ni(II). The resulting resin suspension was subjected to GFAAS. The proposed method was applied to the determination of tin(II) in hydrochloric acid.     

Study of the chemical composition of particulate matter from the Rio de Janeiro metropolitan region,Brazil, by inductively coupled plasma-mass spectrometry and optical emission spectrometry

Air quality in the metropolitan region of Rio de Janeiro was evaluated by analysis of particulate matter (PM) in industrial (Santa Cruz) and rural (Seropédica) areas. Total suspended particles (TSP) and fine particulate matter (PM_2.5) collected in filters over 24 h were quantified and their chemical composition determined. TSP exceeded Brazilian guidelines (80 μg m^− 3) in Santa Cruz, while PM_2.5 levels exceeded the World Health Organization guidelines (10 μg m^− 3) in both locations. Filters were extracted with water and/or HNO₃, and the concentrations of 20 elements, mostly metals, were determined by inductively coupled plasma mass spectrometry (ICP-MS) and optical emission spectrometry (ICP OES). Water soluble inorganic anions were determined by ion chromatography (IC). To estimate the proportion of these elements extracted, a certified reference material (NIST SRM 1648a, Urban Dust) was subjected to the same extraction process. Concordant results were obtained by ICP-MS and ICP OES for most elements. Some elements could not be quantified by both techniques; the most appropriate technique was chosen in each case. The urban dust was also analyzed by the United States Environmental Protection Agency (US EPA) method, which employs a combination of hydrochloric and nitric acids for the extraction, but higher extraction efficiency was obtained when only nitric acid was employed. The US EPA method gave better results only for Sb. In the PM samples, the elements found in the highest average concentrations by ICP were Zn and Al (3–6 μg m^− 3). The anions found in the highest average concentrations were SO₄^2 − in PM_2.5 (2–4 μg m^− 3) and Cl⁻ in TSP (2–6 μg m^− 3). Principal component analysis (PCA) in combination with enrichment factors (EF) indicated industrial sources in PM_2.5. Analysis of TSP suggested both anthropogenic and natural sources. In conclusion, this work contributes data on air quality, as well as a method for the analysis of PM samples by ICP-MS.