Performance of programmed temperature vaporizer, pulsed splitless and on-column injection techniques in analysis of pesticide residues in plant matrices.

A programmed temperature vaporizer (PTV) injection technique has been recently implemented in our laboratory. In present paper its performance is compared with other GC injection techniques commonly used in trace analysis of organic contaminants. Twenty-six pesticides representing different chemical classes were selected for the study. This group comprised compounds typically subjected to discrimination in the injection port of the gas chromatograph, e.g., polar organophosphorus pesticides and thermolabile carbamates. In the first set of experiments standards in pure solvent were injected into GC systems employing different types of injection, i.e., (i) on-column, (ii) pulsed splitless, (iii) PTV solvent split, (iv) PTV splitless, and the responses of analytes were compared. Discrimination of troublesome compounds was significantly decreased with the application of PTV solvent split injection. In the second set of experiments repetitive injections of purified wheat samples were performed, with aims to evaluate the long-term stability of responses, as well as matrix effects in different stages of system contamination for each injection technique. The tolerance of the GC system to co-injected matrix components was increased in the order: on-column相似文献   

Quantitation in capillary gas chromatography with emphasis on the problems of sample introduction

Sampling techniques for practical quantitative capillary GC have to meet certain principal requirements. Both the absolute and the relative peak areas (e.g. column loads) must be reproducible with high precision and at high accuracy; discrimination of certain constituents according to their volatility should not take place on sampling. On the basis of systematic studies, the three most reliable sampling techniques used for GC analyses with the aim of achieving precise and accurate quantitative data proved to be the following: On-column, injection, splitless PTV injection, and an optimized version of split sampling called “cooled needle split” injection. The on-column technique can be optimized by using precolumns with wider internal diameters and without stationary phase coatings to overcome the problems of large liquid sampling volumes and for automation. The PTV technique should only be used in the splitless mode because discrimination cannot be suppressed completely with the split mode. All three of the techniques can be operated automatically, either to avoid “human interference”, i.e. to improve precision or for unattended operation to save man-power.     

大体积进样技术在环境分析中的应用

在毛细管气相色谱法(CGC)中,采用大体积进样技术(LVI),即使用能够容纳大体积样品的进样装置以及增加可控时间的溶剂蒸汽放空装置,可以满足环境样品中超痕量组分的分析要求,简化样品浓缩步骤以及实现液相色谱(LC)与CGC的在线联用。针对分析物的性质、毛细管柱的规格和分析的目的已发展了多种LVI。本文总结了几种常见的LVI,包括柱头进样(OCI)和程序升温进样(PTV),以及近年来发展的一些新技术,如在柱同时溶剂浓缩进样、样品直接引入进样/复杂基质进样和同时溶剂冷凝无分流进样,阐述了各种进样技术的基本原理及其与样品提取、LC纯化在线联用的方法在环境分析应用中的一些最新研究进展。     

Influence of the injection technique and the column system on gas chromatographic determination of polybrominated diphenyl ethers

In this paper, we present an investigation of the influence of the gas chromatographic separation system on the determination of polybrominated diphenyl ethers (PBDEs). Capillary columns, retention gaps and press-fit connectors, as well as different injection techniques have been evaluated with respect to yield and repeatability. The split/splitless injection has been optimized and compared to on-column injection, the septum equipped temperature programmable injector (SPI) and the programmable temperature vaporizing (PTV) injector. Furthermore, a comparison of the different operational modes of the PTV injector is presented. The results show that there are large variations in the yield of PBDEs depending on the column and the injection systems. Especially the high molecular weight BDE congeners can be subject to severe discrimination. Unfavorable conditions can lead to a complete loss of nona and deca substituted BDE congeners.     

Programmed-temperture split-splitless injection of triglycerides: Comparison to cold on-column injection

The performance of split and splitless programmed-temperature (PTV) injection is compared to cold on-column and hot (classical) split injection for the analysis of triglycerides on an apolar capillary gas chromatographic column. Quantitative accuracy and precision of PTV injection are determined for a synthetic mixture of triglycerides relative to cold on-column injection.     

Determination of cholesterol in fat and muscle of pig by HPLC and capillary gas chromatography with solvent venting injection

Two methods for determination of cholesterol in fat and muscle of pig were evaluated: extraction with chloroform:methanol (2:1, v/v) followed by saponification (method 1) and direct saponification (method 2). HPLC and GC were used to determine cholesterol concentrations. GC analysis was performed with a capillary column of 100 μm using a PTV injector in the modes of cold split and solvent venting. Cholesterol was analyzed without derivatization. Both methods of extraction did not present significant differences (p > 0.01). Sample analysis by GC with solvent venting injection and HPLC showed the lowest % r.s.d. but GC in the cold split mode allowed to obtain a shorter analysis time. Cholesterol concentrations obtained by HPLC were not statistically different from the results obtained by GC with solvent venting injection and were slightly lower than those previously reported. Cholesterol concentrations in fat and muscle tissues respectively ranged from 52 to 77 mg/100 g and from 55 to 65 mg/100 g.     

Analysis of class 1 residual solvents in pharmaceuticals using headspace-programmed temperature vaporization-fast gas chromatography-mass spectrometry

A sensitive method is presented for the fast screening and determination of residual class 1 solvents (1,1-dichloroethene, 1,2-dichloroethane, 1,1,1-trichloroethane, carbon tetrachloride and benzene) in pharmaceutical products. The applicability of a headspace (HS) autosampler in combination with GC equipped with a programmed temperature vaporizer (PTV) and a MS detector is explored. Different injection techniques were compared. The benefits of using solvent vent injection instead of split or splitless-hot injection for the measurement of volatile compounds are shown: better peak shapes, better signal-to-noise ratios, and hence better detection limits. The proposed method is extremely sensitive. The limits of detection ranged from 4.9 ppt (benzene) to 7.9 ppt (1,2-dichloroethane) and precision (measured as the relative standard deviation) was equal to or lower than 12% in all cases. The method was applied to the determination of residual solvents in nine different pharmaceutical products. The analytical performance of the method shows that it is appropriate for the determination of residual class 1 solvents and has much lower detection limits than the concentration limits proposed by the International Conference on Harmonization (ICH) of Technical Requirements for the Registration of Pharmaceuticals for Human Use. The proposed method achieves a clear improvement in sensitivity with respect to conventional headspace methods due to the use of the PTV.     

AT-column, a novel concentrating technique for large-volume injections in gas chromatography

Nowadays, large-volume injection is widely used for the GC determination of trace analytes, specifically to improve detectability. The most popular injectors for large-volume injections are the programmable temperature vaporisation (PTV) injector and the cold on-column (COC) injector, where each device has its own advantages and limitations. The novel AT-column concentrating technique combines features of two other injection techniques, loop-type large-volume and vapour overflow. AT-column injection is based on solvent evaporation in an empty liner with solvent vapour discharge via the split line. Little or no optimisation is required. The only relevant parameter is the injection temperature which can easily be calculated using the equation of Antoine. As an application, AT-column injection is combined with GC-MS for the trace-level determination of labile analytes and with GC-flame ionisation detection for the analysis of high molecular weight polymer additives. In summary, AT-column is an injection technique that combines the inertness of the COC, and the flexibility and robustness of the PTV large-volume technique.     

Capillary gas chromatography of tert-butyldimethlysilylamino acids with PTV injection

The programmable temperature vaporizing injector (PTV) has been used to study the effects of injection temperature and initial heating period on the FID response factors of TBDMS derivatives of 17 protein amino acids. The relative response factors were calculated for injection temperatures of 50°C, 90°C, 160°C, 220°C, and 260°C with different initial heating periods (1 s, 5 s, and 10 s) and the results compared with the values obtained for the calculated response factors obtained under classical split injection conditions (300°C, continuous). Except for expected peak broadening effects, the initial heating period does not seem to have significative effects on relative peak areas. The response to the derivatives of alanine, glycine, α-aminobutyric acid, valine, proline, methionine, cysteine, phenylalanine, asparagine, and arginine was only slightly affected by increasing the injection temperature whereas the response factors for the derivatives of serine, threonine, glutamic acid, lysine, histidine, tyrosine, and tryptophan were strongly dependent upon initial injection temperatures, decreasing rapidly at temperatures above 160°C. The cold split-splitless injection is clearly advantageous over the classical hot injection techniques for the analysis of this type of aminoacid derivative.     

Programmable Temperature Vaporizer (PTV) Applied to the Triglyceride Analysis of Milk Fat

The PTV (Programmable Temperature Vaporizer) is a split/splitless injector which allows the sample to be introduced at a relatively low temperature, thus affording accurate and reproducible sampling. After injection the PTV is rapidly heated to transfer the vaporized components into the capillary column. This type of injector has proved to be an efficient tool for the evaluation of fatty acids, essential oils, and pesticides in food analysis. In this work the suitability of PTV for the analysis of milk fat purity by the Official EU method was evaluated. This method is based on the gas chromatographic determination of triglycerides only according to their total number of carbon atoms followed by the application of formulae deriving from multiple linear regressions. The analysis is currently carried out with a packed column or a short capillary column and an on-column injection system. Several samples of pure milk fat and mixtures of milk fat with foreign fat were analyzed with the same capillary column and by using both PTV and on-column injection systems. The results show that the gas chromatographic profile obtained by PTV is comparable with that obtained by the on-column injector, while repeatability and reproducibility data meet the requirements indicated in the Official Method. Therefore, this study demonstrates that it is possible to use the PTV instead of the on-column injector to determine the purity of milk fat with this method.     

Gas chromatographic separation of sugars by on-column injection on glass capillary columns

Sugars were separated gas chromatographically on short apolar glass capillary columns by using cold, on-column injection (OCI) techniques. After silylation, oligomers up to the hexasaccharides could be efficiently separated in resonable retention times. Response factors of silylated sugars were determined as a function of varying sample amounts and concentrations. The optimum injection amount was found to be 1 μl in heptane as solvent.     

Improving the reproducibility of quantitative gas-liquid chromatography by modifying the injection system

Summary In order to increase accuracy of split ratio measurements by interruption of the septum purge gas stream a gas chromatograph (GLC) sample injection system was modified by the introduction of a rapid-action gate-valve in the appropriate gas line. The effects of this modification are described. It is shown to improve the reproducibility of injected amounts in multiple analysis and thus the accuracy of quantitative determinations.     

Vaporising systems for large volume injection or on-line transfer into gas chromatography: Classification, critical remarks and suggestions

Techniques for large volume introduction of liquid samples into capillary gas chromatography (GC) follow a small number of principals. Vaporising systems, vapour discharge modes and methods for solvent-solute separation are classified and evaluated.

Presently, programmed temperature vaporising (PTV) solvent split injection is the preferred method if on-column techniques cannot be applied. Critical re-evaluation suggests, however, that solvent evaporation and solvent-solute separation should be performed in separate compartments and optimized individually. Permanently hot chambers offer the highest capacity for solvent evaporation. The preferred techniques for solvent-solute separation are stationary phase focusing in a coated capillary or solvent trapping in an uncoated capillary precolumn. The vaporising chamber-precolumn solvent split-gas discharge system is proposed for large volume injection and on-line transfer of water-containing solvent mixtures, and in-line vaporiser-precolumn solvent split-overflow system for most on-line transfer applications.     

Large volume injection techniques in capillary gas chromatography

Large volume injection (LVI) is a prerequisite of modern gas chromatographic (GC) analysis, especially when trace sample components have to be determined at very low concentration levels. Injection of larger than usual sample volumes increases sensitivity and/or reduces (or even eliminates) the need for extract concentration steps. Also, an LVI technique can serve as an interface for on-line connection of GC with a sample preparation step or with liquid chromatography. This article reviews the currently available LVI techniques, including basic approaches to their optimization and important real-world applications. The most common LVI methods are on-column and programmed temperature vaporization (PTV) in solvent split mode. Newer techniques discussed in this article include direct sample introduction (DSI), splitless overflow, at-column, and "through oven transfer adsorption desorption" (TOTAD).     

Comparison of packed and capillary columns for quantitative gas chromatography of triglycerides in milk fat

Summary Quantitative gas chromatography of triglycerides in conjunction with established triglyceride formulae can be used to determine various milk fat parameters. Since the evaluation of, for example, iodine number or content of non-milk fats (foreign fats) in milk fat requires only the separation of triglycerides by carbon number and since repeatabilities, especially of the highboiling triglycerides, have been less acceptable with capillary columns in the past, packed columns have been used exclusively. There is, however, an increasing demand for the use of capillary instead of packed columns and to that end the present investigation has been carried out. To achieve a suitable resolution, with this particularly exacting high-temperature application, a short 5 m capillary column of extreme temperature stability has been used. As well as modification of various analytical conditions different injection techniques have been investigated. On-column, PTV and split injection were compared with regard to repeatability. The cold-on-column injection technique was found to produce the best results, being comparable to the excellent precision of a packed column. Thus, a method is now available by means of which the determination of milk fat parameters by the triglyceride formulae, such as the amount of foreign fats in milk fat, can now be carried out with a standardized capillary column.     

Headspace-programmed temperature vaporizer-fast gas chromatography-mass spectrometry coupling for the determination of trihalomethanes in water

A new method based on the use of a headspace autosampler in combination with a GC equipped with a programmable temperature vaporizer (PTV) and an MS detector has been developed for the screening and quantitative determination of trihalomethanes (THMs) in different aqueous matrices. The use of headspace generation to introduce the sample has the advantage that no prior sample treatment is required, thus minimizing the creation of analytical artifacts and the errors associated with this step of the analytical process. The PTV inlet used was packed with Tenax-TA. The injection mode was solvent vent, in which the analytes are retained in the hydrophobic insert packing by cold trapping, while the water vapour is eliminated through the split line. This allows rapid injection of the sample in splitless mode, very low detection limits being achieved without the critical problem of initial sample bandwidth. The capillary column used allowed rapid separations with half-height widths ranging from 1.68 s (chloroform) to 0.66 s (bromoform). The GC run time was 7.3 min. The use of mass spectrometry allows the identification and quantification of the analytes at the low ppt level. The S/N ratio was at least 10-fold higher when the SIM mode was used in data acquisition as compared to the scan mode. The proposed method is extremely sensitive, with detection limits ranging from 0.4 to 2.6 ppt.     

Critical aspects of the determination of pentafluorobenzyl derivatives of aldehydes by gas chromatography with electron-capture or mass spectrometric detection: Validation of an optimized strategy for the determination of oxygen-related odor-active aldehydes in wine

This work presents a thorough study of some aspects critical to the quantitative performance of methods for the determination of volatile aldehydes previously derivatized to pentafluorobenzyl hydroxylamine oximes. The conclusions of the study are further applied to the validation of an optimized procedure for the determination of oxidation-related aldehydes from wine. Aspects studied include the chromatographic injection, the analytical performance of electron-capture detection (ECD) or MS detection, and the way in which the derivatization is carried out. Different injection techniques have been optimized and compared (classical splitless-hot injection; cold splitless; and large volume solvent split injection). All of them were carried out in a programmed temperature vaporization (PTV) injector, with a 350 microL internal volume liner (3.4 mm internal diameter). Classical splitless injection of hexane extracts is troublesome and requires large carrier gas flows (>10 mL min(-1)). Cold splitless injection was clearly superior. Large volume solvent split injection has been also optimized. ECD has been found to lack the necessary selectivity for the determination of unsaturated aldehydes in wine, although the quantitation of several minor aldehydes is possible. MS detection has proven to be superior for the determination of these compounds in wine. The way in which the reagent is applied is also critical and for the case of wine is important to ensure that the reagent is applied after some of the major wine aldehydes have been eliminated. The finally proposed method is extremely sensitive. Method detection limits ranged from 0.002 microg L(-1) (for unsaturated aldehydes) to 0.73 microg L(-1) (for phenylacetaldehyde) and precision (measured as relative standard deviation) is < or =6% in all cases. The method makes it possible to determine quantitatively in a single run the wine aldehydes with sensory significance (isobutyraldehyde, 2-methylbutanal, isovaleraldehyde, (E)-2-hexenal, (E)-2-heptenal, (E)-2-octenal, (E)-2-nonenal, methional and phenylacetaldehyde).     

Optimisation of programmable temperature vaporizer-based large volume injection for determination of pesticide residues in fruits and vegetables using gas chromatography-mass spectrometry

The applicability of programmable temperature vaporizer (PTV) solvent vent injection to the gas chromatographic (GC) determination of pesticide residues in fruits and vegetables was evaluated with the aim of miniaturizing the current multiresidue method. For that purpose 24 pesticides representing different chemical classes were initially chosen for optimisation of the large volume injection (LVI) parameters. Various parameters related to the optimum injector performance were tested for several types of packed and empty liners using both fast (at-once) and speed-controlled PTV solvent vent injection of standard solutions in ethyl acetate. In the next step, several packed and empty liners were evaluated for their suitability for pesticide multiresidue analysis. Parameters identified as optimal were then applied for PTV solvent vent injection of sample extracts prepared using the miniaturized multiresidue method to assess the long-term stability of the system. The combined use of large volume injection of 10 microl ethyl acetate extract into an empty multi-baffled or a CarboFrit packed liner using PTV injectors and GC-MS analysis enabled the detection and quantification of 124 pesticides in fruit and vegetable samples at the 0.01 mg/kg level using miniaturized reversed-phase solid-phase extraction (RP-SPE) of diluted acetone extract and clean-up on a small anion-exchange SPE column.     

Application of programmed-temperature split/splitless injection to the trace analysis of aliphatic hydrocarbons by gas chromatography.

The dependence of the programmed-temperature solvent split sampling technique using a PSS (programmed-split/splitless) injection mode on different variables affecting the introduction of large sample volumes for a mixture of alkanes in capillary GC was evaluated. Apart from the studies found in the literature on different factors such as speed of injection. presence of adsorbent in the liner, internal diameter of the liner, initial and final injector temperature, split flow-rate and initial split time, affecting the chromatographic signal of different compounds, others were studied whose influence has not been considered until now. They include length of the microsyringe needle, adsorbent distribution in the liner, injection volume on analyte discrimination, speed of injector heating, time which the column stays at the initial temperature and time that the injector stays at the final temperature. Once finalised, the study of the PSS injection mode was compared with the conventional mode of gas chromatography splitless injection, and found that the proposed method increases sensitivity in GC trace analysis. Finally, the application of both injection modes in the determination of aliphatic hydrocarbons was tested in an atmospheric particulate sample.     

Pesticide residue analysis in food with CGC — study of long-term stability by the use of different injection techniques

An experiment was designed to study the long-term stability of analyses of pesticide residues in a complex food matrix using three different injection techniques. A spinach sample was spiked with five sulfur-containing pesticides of varying volatility and thermolability: azinphos-ethyl, dimethoate, methiocarb, ethiofencarb, and tri-allate. Tri-allate was selected as internal standard because of its thermal stability and its good chromatographic properties. Flame photometric detection resulted in chromatograms not subject to interference by peaks of compounds of the matrix. Starting with a clean and freshly, silanized injector an additional deactivation was found to occur on the first injection of a food sample resulting in an increased peak area for all pesticides in relation to tri-allate. Highest long-term stability was found with PTV injection. Best results for thermolabile carbamates were obtained using on-column injection. However, they were prone to faster deterioration.