Effect of nanocrystallization on the mechanical and magnetic properties of finemet-type alloy (Fe<Subscript>78.5</Subscript>Si<Subscript>13.5</Subscript>B<Subscript>9</Subscript>Nb<Subscript>3</Subscript>Cu<Subscript>1</Subscript>)

The kinetics of primary crystallization and the effect of structural parameters of the precipitating nanocrystalline α-phase Fe-Si on changes in microhardness, coercive force, and saturation magnetization in an amorphous Finemet-type 5BDSR alloy (Fe_78.5Si_13.5B₉Nb₃Cu₁) obtained by melt quenching are studied. It is found that both an increase in bulk density and an increase in the average nanoparticle size contribute to the hardening of the amorphous/nanocrystalline alloy.     

Magnetocaloric effect in (La<Subscript>0.6</Subscript>Ca<Subscript>0.4</Subscript>)<Subscript>0.9</Subscript>Mn<Subscript>1.1</Subscript>O<Subscript>3</Subscript>

The results of investigations of the magnetization, susceptibility, and magnetic-field-induced changes in the entropy of polycrystalline manganite (La_0.6Ca_0.4)_0.9Mn_1.1O₃ near the magnetic phase transition have been presented. Magnetic measurements have been carried out at temperatures in the range from 210 to 310 K in magnetic fields of up to 9 T. The magnetocaloric effect has been revealed by measuring the magnetic-field dependences of magnetization. The magnitude of the magnetocaloric effect is compared with similar results obtained for other manganites.     

Magnetic and Mössbauer Studies of Fe<Subscript>76</Subscript>Mo<Subscript>8</Subscript>Cu<Subscript>1</Subscript>B<Subscript>15</Subscript> Amorphous Alloy

“Zero field”-Mössbauer and magnetization measurements have been performed on an amorphous Fe₇₆Mo₈Cu₁B₁₅ alloy in the temperature range of (10-340) K. The room-temperature Mössbauer spectrum exhibits magnetic dipole and electric quadrupole interactions. At approximately 306 K, the magnetic interactions vanish and the alloy shows fully paramagnetic behavior. On the other hand, the relative representation of paramagnetic component becomes weak with decreasing temperature and below 220 K the magnetic dipole interactions prevail. Below this temperature an anomaly in the low-temperature dependencies of ac susceptibility and of magnetization, measured during cooling the specimen from 340 K down to 20 K is observed. The anomaly on the magnetization curve vanishes in the field of 200 Oe.     

Modulated magnetic structure in quasi-one-dimensional clinopyroxene NaFeGe<Subscript>2</Subscript>O<Subscript>6</Subscript>

The magnetic structure of the NaFeGe₂O₆ monoclinic compound has been experimentally investigated using the elastic scattering of neutrons. At a temperature of 1.6 K, an incommensurate magnetic structure has been observed in the form of an antiferromagnetic helix formed by a pairs of the spins of the Fe³⁺ ions with helical modulation in the ac plane of the crystal lattice. The wave vector of the magnetic structure has been determined and its temperature behavior has been studied. The analysis of the temperature dependences of the specific heat and susceptibility, as well as the isotherms of the field dependence of the magnetization, has revealed the existence of not only the order-disorder magnetic phase transition at the point T _N = 13 K, but also an additional magnetic phase transition at the point T _c = 11.5 K, which is assumingly an orientation phase transition.     

Magnetic,thermal, and electrical properties of an Ni<Subscript>45.37</Subscript>Mn<Subscript>40.91</Subscript>In<Subscript>13.72</Subscript> Heusler alloy

The magnetization, the electrical resistivity, the specific heat, the thermal conductivity, and the thermal diffusion of a polycrystalline Heusler alloy Ni_45.37Mn_40.91In_13.72 sample are studied. Anomalies, which are related to the coexistence of martensite and austenite phases and the change in their ratio induced by a magnetic field and temperature, are revealed and interpreted. The behavior of the properties of the alloy near Curie temperature T_C also demonstrates signs of a structural transition, which suggests that the detected transition is a first-order magnetostructural phase transition. The nontrivial behavior of specific heat detected near the martensite transformation temperatures is partly related to a change in the electron density of states near the Fermi level. The peculiar peak of phonon thermal conductivity near the martensitic transformation is interpreted as a consequence of the appearance of additional soft phonon modes, which contribute to the specific heat and the thermal conductivity.     

Effect of external actions on the magnetic properties and corrosion resistance of Co<Subscript>70.5</Subscript>Fe<Subscript>0.5</Subscript>Cr<Subscript>4</Subscript>Si<Subscript>7</Subscript>B<Subscript>18</Subscript> amorphous alloy

Variations in the magnetic characteristics (specific saturation magnetization and coercive force) of Co–Fe–Cr–Si–B amorphous alloy (AA) are studied after high-pressure torsion (HPT) and heat treatment. The behavior of AA magnetic properties is analyzed with respect to structural transformations caused by external actions. The corrosion resistance of AA upon transitioning from an amorphous to a crystalline state is investigated. The established optimum annealing and HPT conditions yield a satisfactory combination of the magnetic properties and corrosion resistance of the investigated alloy.     

Effect of the Structural Disorder and Short-Range Order on the Electronic Structure and Magnetic Properties of the Fe<Subscript>2</Subscript>VAl Heusler Alloy

The Fe₂VAl Heusler alloy is of great interest because ab initio calculations predict the absence of magnetization in it and a half-metal behavior with a pseudogap at the Fermi level. At the same time, experimental data (low-temperature specific heat, electrical resistivity, and magnetic properties) show that it is difficult to achieve such characteristics, and Fe₂VAl samples usually have the characteristics of a poor magnetic metal. Ab initio calculations have been performed for ordered and disordered (Fe_1–xV _x )₃Al Heusler alloys with x = 0.33. It has been shown that the alloy in a structurally ordered state (L2₁ structure) is a half-metal with a deep pseudogap at the Fermi level and does not have magnetization. At the same time, antisite defects in the iron and vanadium sublattices of the disordered alloy (D0₃ structure) lead to an increase in the conductivity and to the appearance of spin polarization and magnetization of (2.1±0.1)μ_B/f.u. The short-range order in the disordered phase has been generated by increasing the concentration of clusters characteristic of the bcc structure of α-Fe, which results in an increase in the magnetization to (2.5±0.1)μ_B/f.u.     

X-ray diffraction studies of the structure of nanocrystals in Fe<Subscript>73.5</Subscript>Si<Subscript>13.5</Subscript>B<Subscript>9</Subscript>Nb<Subscript>3</Subscript>Cu<Subscript>1</Subscript> soft magnetic alloys before and after thermomechanical treatment

The structure of the Fe_73.5Si_13.5B₉Nb₃Cu₁ soft magnetic alloy has been investigated using X-ray diffraction in transmission geometry. The initial alloy prepared by rapid quenching from the melt has a short-range order (∼2 nm) in the atomic arrangement, which is characteristic of the Fe-Si structure with a body-centered cubic lattice. The alloy subjected to annealing contains Fe-Si nanocrystals with sizes as large as 10–12 nm. The annealing under a tensile load leads to an extension of the nanocrystal lattice so that, after cooling, a significant residual deformation is retained. This can be judged from the relative shifts of the (hkl) peaks in the X-ray diffraction patterns measured for two orientations of the scattering vector, namely, parallel and perpendicular to the direction of the load applied. The deformation is anisotropic: within the accuracy of the experiment, no distortions in the [111] direction are observed and the distortions in the [100] direction are maximum. It is known that crystals with a composition close to Fe₃Si exhibit a negative magnetostriction; i.e., their magnetization induced under a load (Villari effect) applied along the [100] direction is perpendicular to this direction along one of the easy magnetization ([010] or [001]) axes. In the alloy, the orientation of the nanocrystal axes is isotropic and the majority of the nanocrystals have a composition close to Fe₃Si. The direction of magnetization of these nanocrystals is determined by the residual deformation of their lattice and lies near the plane perpendicular to the direction of the tensile load applied during heat treatment. This is responsible for the appearance of transverse magnetic anisotropy of the easy-plane type in the Fe_73.5Si_13.5B9Nb₃Cu₁ alloy.     

Magnetically induced phase transitions in LaCoO<Subscript>3</Subscript> in fields of up to 500 T

The differential magnetization of LaCoO₃ in magnetic fields of up to 500 T has been measured at a temperature of 4.2 K. The magnetization curve reveals several features which suggest a complex pattern of the transition of LaCoO₃ from the low-spin state to the high-spin state. The magnetic moment starts to grow in fields above 50 T to reach a plateau in the 130–240-T region, after which the magnetic moment continues to rise up to saturation in fields ∼500 T.     

Magnetically controlled thermoelastic martensite transformations and properties of a fine-grained Ni<Subscript>54</Subscript>Mn<Subscript>21</Subscript>Ga<Subscript>25</Subscript> alloy

Comparative studies of physical characteristics (the electrical resistivity, the magnetic susceptibility, the magnetization, the bending deformation, and the degree of shape recovery during subsequent heating) of the Ni₅₄Mn₂₁Ga₂₅ ferromagnetic alloy as-cast and rapidly quenched from melt have been performed in the temperature range 2–400 K. The results are compared to the results of studying the structural–phase transformations by transmission and scanning electron microscopy and X-ray diffraction. It is found that the rapid quenching influences the microstructure, the magnetic state, the critical temperatures, and the specific features of thermoelastic martensite transformations in the alloy. It is found that the resource of the alloy plasticity and thermomechanical bending cyclic stability demonstrates a record-breaking increase in the intercritical temperature range and during subsequent heating.     

Structure of tetragonal martensite in the In<Subscript>95.42</Subscript>Cd<Subscript>4.58</Subscript> cast alloy

The structure of martensite in the In_95.42Cd_4.58 alloy has been studied by metallography, X-ray diffraction, dilatometry, and transmission electron microscopy. It has been shown that a massive structure built of colonies of tetragonal lamellar plates divided by a twin boundary {101}FCT is formed in the alloy under cooling below the martensite FCC → FCT transition temperature. The alloy recrystallizes after a cycle of FCT → FCC → FCT transitions with a decrease in the grain size by several times compared with the initial structure such fashion that the size of massifs and individual martensite lamella in the massif correlates with the change in the size of the alloy grain. Using thermal cycling, it has been revealed that the alloy tends to stabilize the high-temperature phase.     

Structural and magnetic properties of size-controlled Mn<Subscript>0.5</Subscript>Zn<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles and magnetic fluids

Mn_0.5Zn_0.5Fe₂O₄ ferrite nanoparticles with tunable Curie temperature and saturation magnetization are synthesized using hydrothermal co-precipitation method. Particle size is controlled in the range of 54 to 135 Å by pH and incubation time of the reaction. All the particles exhibit super-paramagnetic behaviour at room temperature. Langevin’s theory incorporating the interparticle interaction was used to fit the virgin curve of particle magnetization. The low-temperature magnetization follows Bloch spin wave theory. Curie temperature derived from magnetic thermogravimetric analysis shows that Curie temperature increases with increasing particle size. Using these particles magnetic fluid is synthesized and magnetic characterization is reported. The monolayer coating of surfactant on particle surface is confirmed using thermogravimetric measurement. The same technique can be extended to study the magnetic phase transition. The Curie temperature derived using this measurement complies with the low-temperature magnetic measurement. The room-temperature and high-temperature magnetization measurements are also studied for magnetic fluid systems. The magnetic parameters derived for fluid are in good agreement with those obtained for the particle system.     

Optical properties of the Cr<Subscript>5</Subscript>S<Subscript>6</Subscript> single crystal

Results of the investigation of optical density spectra of Cr₅S₆ single crystals in the infrared region have been presented. A comparative analysis of the temperature dependences of the magnetization and the light absorption has been performed. Physical mechanisms to explain the specific features of the spectral and temperature dependences of the optical density have been proposed.     

Magnetic properties and the magnetoimpedance effect of nanostructured Fe<Subscript>73.5</Subscript>Si<Subscript>16.5</Subscript>B<Subscript>6</Subscript>Nb<Subscript>3</Subscript>Cu<Subscript>1</Subscript> ribbons with induced magnetic anisotropy

The structure and magnetic properties and the magnetoimpedance effect of nanocrystalline Fe_73.5Si_16.5B₆Nb₃Cu₁ alloy ribbons, obtained from the amorphous state by annealing under different conditions, were comparatively analyzed. Despite the similarity of the samples’ structural states and the processes of their quasi-static magnetization reversal, the features of the magnetoimpedance effect are indicative of significant differences in the processes of their dynamic magnetization.     

Influence of deformation on the structural transformation of the Pd<Subscript>40</Subscript>Ni<Subscript>40</Subscript>P<Subscript>20</Subscript> amorphous phase

The influence of plastic deformation on the structure of the Pd₄₀Ni₄₀P₂₀ amorphous alloy has been investigated using X-ray diffraction and measurements of the velocity of sound. It has been revealed that the rolling of the sample leads to a change in the structure of the amorphous phase (distortion of the first coordination sphere) and that the structural transformations are more pronounced in the near-surface region of the sample. The rolling also results in a decrease in the transverse velocity of sound. The observed effects decrease with time. It has been demonstrated that the revealed effects are associated with the inelastic deformation of the amorphous alloy.     

Transport and magnetic properties of a Zn<Subscript>0.1</Subscript>Cd<Subscript>0.9</Subscript>GeAs<Subscript>2</Subscript> + 10 wt % MnAs composite with magnetic clusters at high pressure

The temperature (T = 77–420 K) dependences of the electrical resistivity and the magnetization, the magnetic-field (H ≤ 5 kOe) and pressure (P ≤ 7 GPa) dependences of the resistivity, the Hall coefficient, and the magnetization have been measured in the Zn_0.1Cd_0.9GeAs₂ + 10 wt % MnAs composite with the Curie temperature T _C = 310 K. The magnetoresistive effect has been observed at high hydrostatic pressure to 7 GPa. At nearly room temperature, the pressure dependence of the magnetization demonstrated a transition from the ferromagnetic to paramagnetic state at P ~ 3.2 GPa that was accompanied by the semiconductor–metal phase transition.     

Atomic and magnetic structures of Fe<Subscript>70</Subscript>Al<Subscript>5</Subscript>B<Subscript>25</Subscript> amorphous alloys

The short-range order around boron, aluminum, and iron atoms in Fe₇₅B₂₅ and Fe₇₀Al₅B₂₅ amorphous alloys has been studied by ¹¹B and ²⁷Al nuclear magnetic resonance at 4.2 K and ⁵⁷Fe Mössbauer spectroscopy at 87 and 295 K. The average magnetic moment of iron atoms μ(Fe) in these alloys has been measured by a vibrating sample magnetometer. It has been revealed that the substitution of aluminum atoms for iron atoms does not disturb μ(Fe) in the Fe₇₀Al₅B₂₅ alloy, gives rise to an additional contribution to the ¹¹B NMR spectrum in the low-frequency range, and shifts maxima of the distribution of hyperfine fields at the ⁵⁷Fe nuclei. In the Fe₇₀Al₅B₂₅ amorphous alloy, the aluminum atoms substitute for iron atoms in the nearest coordination shells of boron and iron atoms. This alloy consists of nanoclusters in which boron and iron atoms have a short-range order of the tetragonal Fe₃B phase type.     

Effect of megaplastic deformation on the magnetic properties of FeNi alloy

The effect megaplastic deformation has on the coercivity and specific saturation magnetization of soft-magnetic equiatomic FeNi alloy is studied at room temperature in a Bridgman chamber by means of X-ray diffraction, Mössbauer spectroscopy and magnetometry. Structural features responsible for changes in the alloy’s properties at different stages of deformation are revealed.     

Magnetic properties of the CuCoAlBO<Subscript>5</Subscript> single crystal

High-quality CuCoAlBO₅ single crystals have been grown, and their crystal structure, magnetic susceptibility, and magnetization have been studied. It has been established that the CuCoAlBO₅ compound is an uncompensated antiferromagnet or ferrimagnet with a small magnetic moment and the magnetic ordering temperature T _N = 28 K. A model has been proposed for the magnetic structure. A strong anisotropy of the magnetic properties has been revealed.