Synthesis, characterization and analytical applications of Ni(II)-ion imprinted polymer

Ion recognition-based separation techniques have received much attention because of their high selectivity for target ions. In this study, we have prepared a novel ion imprinted polymer (IIP) to remove nickel ions with high selectivity. The imprinted polymer was prepared by copolymerization of 2-hydroxy ethyl methacrylate (HEMA) with nickel vinylbenzoate complex in the presence of ethylene glycol dimethacrylate (EGDMA) as a crosslinker. The polymerization was carried out in bulk with free radical initiation using 2-methoxy ethanol as a solvent and porogen. The adsorbed nickel was completely eluted with 15 mL of 1 M HCl. Control polymer was also prepared by similar experimental conditions without using imprint ion. The above synthesized polymers were characterized by surface area measurements, FT-IR, microanalysis and SEM analysis. The adsorption capacity of IIP and CP was found to be 1.51 and 0.65 mmol g⁻¹, respectively. The optimal pH for quantitative enrichment was 6.5. Nature of eluent, eluent concentration and eluent volume were also studied. The relative selectivity factor (α_r) values of Ni(II)/Zn(II), Ni(II)/Cu(II) and Ni(II)/Co(II) were 78.6, 111.1 and 91.6, respectively. Five replicate determinations of 30 μg L⁻¹ of Ni(II) gave a mean absorbance of 0.067 with a relative standard deviation of 1.06%. The lowest concentration determined by GTA-AAS below which the recovery becomes non-quantitative is 6 μg L⁻¹. IIP was tested for removal of Ni(II) from sea water sample.     

Crystal structure of Ni(II) complex and fluorescence properties of Zn(II) complex with the Schiff base derived from diethenetriamine and PMBP

The Schiff base, H₂L, was derived from 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (PMBP) and diethenetriamine. The crystal structure of [NiL(C₂H₅OH)]·H₂O obtained from ethanol solution was determined by X-ray diffraction analysis. The coordination geometry of Ni(II) ion is a distorted octahedron with three oxygen atoms and three nitrogen atoms. Under the excitation of ultraviolet light, strong fluorescence of solid Zn(II) complex was observed. In addition, the fluorescence enhancement was obtained in the presence of Zn²⁺ in THF solution of the ligand, indicating that H₂L may be a potential fluorescent sensor for Zn²⁺.     

Electrical conductivity and photoconductivity of polymer composites containing Cu(II)/Cr(III) heteropolynuclear complexes

The electrical conductivity and photoconductivity of films of composites based on electrically neutral poly(vinyl butyral) with additions of Cu(II)/Cr(III) heteropolynuclear complexes introduced in the form of solutions or mechanically ground polycrystalline powders are studied. Photocurrents in samples prepared in different ways differ no more than tenfold. The photoconductivity of the composite films increases with decreasing distance between the metal centers in the complexes. A phenomenological model of carrier photogeneration and transport in films of polymer composites with embedded particles of heteropolynuclear complexes prepared from a solution or by grinding is proposed. The slight difference in photocurrents between samples containing the same complexes but prepared by different methods can be accounted for by the close geometric sizes of particles of the complexes.     

Dispersion of dielectric characteristics of polymer structures based on the Cu(II) complex

The results of the study of the dielectric response of thin-layer polymer films based on [Cum-Salpn-1,3] monomers and the H₂mSalpn-1,3 ligand synthesized by electrochemical polymerization are presented. A frequency dispersion of dielectric characteristics that corresponds to the distribution of a set of relaxors is revealed. The role of a metal center, i.e., divalent copper, and the azomethine group during dielectric polarization is discussed.     

Hybrid of chitin and humic acid as high performance sorbent for Ni(II)

Hybrid of humic acid (HA) and chitin has been synthesized and the hybrid material (chitin-HA) was then applied as sorbent to adsorb Ni(II). The HA was extracted from peat soil of Gambut District, South Kalimantan, Indonesia, according to the procedure recommended by IHSS (International Humic Substances Society). The chitin was isolated from crab shell waste of sea food restaurants through deproteination using NaOH 3.5% (w/v) and followed by removal of inorganic impurities using HCl 1 M. The synthesis of chitin-HA was performed by reacting gelatinous chitin solution in HCl 0.5 M and HA solution in NaOH 0.5 M. Parameters investigated in this work consists of effect of medium acidity on the sorption, sorption rate (k_s) and desorption rate (k_d) constants, Langmuir (monolayer) and Freundlich (multilayer) sorption capacities, and energy (E) of sorption. The k_s and k_d were determined according to a kinetic model of first order sorption reaching equilibrium, monolayer sorption capacity (b) and energy (E) were determined according to the Langmuir isotherm model, and multilayer sorption capacity (B) was determined based on the Freundlich isotherm model.Sorption of Ni(II) on both chitin and chitin-HA was maximum at pH 8.0. The kinetic expression resulted from the proposed kinetic model has been shown to be more applicable than the commonly known Lagergren equation obtained from the pseudo-first order sorption model. The application of the proposed model revealed that the presence of HA increased the k_s from 0.018 min⁻¹ for chitin to 0.031 min⁻¹ for chitin-HA. As for k_s, the value of b was also bigger in the presence of HA, i.e. 7.42 × 10⁻⁵ mol/g for chitin and 9.93 × 10⁻⁵ mol/g for the chitin-HA. Unlike k_s and b, the value of E slightly decreased from 23.23 to 21.51 kJ/mol for the absence and presence of HA, respectively. It can also be deduced that the presence of HA on chitin contributed more to the additional layer of Ni(II) sorbed on sorbent. Without HA, B for chitin was only 6.17 times higher than b, while with the presence of HA, the enhancement of the sorption capacity from the multilayer (B) to the monolayer (b) was 19.40. The increase of k_s, b, B, and the decrease of E would be very benefit in the real application of chitin-HA for the recovery of Ni(II) from aqueous samples.     

Nanoparticles of Ni(II) and Co(II) metallo-organic molecular materials

We have investigated the effect of thermal annealing on the diode characteristics of solution-processed novel core–shell coaxial n–p nanorods heterojunction consisting of n-type ZnO as a core and p-type CuS as a shell material. The values of turn-on-voltage, rectification ratio, reverse saturation current density, barrier height, and ideality factors have been improved as the as-prepared heterojunction is annealed at higher temperatures owing to the improvement in the interface between ZnO and CuS as evidenced from the high-resolution transmission electron microscopy. The X-ray diffraction results also confirm the improvement in the crystalline quality of ZnO and CuS through annealing. The experimental current–voltage data are consistent with the presence of dominating recombination-tunneling conduction occurring through the interface defect states between ZnO and CuS. The results demonstrate that an annealing process plays a dominant role in the interfacial defects which helps to modify the diode performance paving a way to cheaper electronic nanodevices.     

ESCA study of Ni(II) dithiocarbazato complexes

N 1s, S 2p and Ni 2p_3/2 binding energies for the Ni(II) dithiocarbazates and N 1s and S 2p binding energies for the methyl esters of dithiocarbazic acids were measured. It was found that the band width of N 1s narrows on going from the esters to the complexes, thus suggesting a closer similarity between the two nitrogen atoms as a consequence of coordination. S 2p binding energies were found to be similar in the above complexes independent of the chromophore present in them. A possible explanation is suggested for this unusual result.     

High performance polymer light-emitting diodes doped with a novel phosphorescent iridium complex

High performance polymer light-emitting diodes (PLEDs) based on a phosphor of noble metal complex bis(1,2-dipheny1-1H-benzoimidazole) iridium (acetylacetonate) [(pbi)₂Ir(acac)] doped in poly(N-vinylcarbazole) (PVK) host with various concentration were demonstrated. The photoluminescence (PL) and electroluminescence (EL) spectra of the PLEDs exhibited an emission intensity decrease of PVK and a gradually enhanced feature of (pbi)₂Ir(acac) with increased doping concentration. The device with a 5 wt% (pbi)₂Ir(acac) doped PVK system showed a high power efficiency of 3.84 lm/W and a luminance of 26,006 cd/m². The results indicated that both energy transfer and charge trapping have a significant influence on the performance of PLEDs. The devices have a broadened EL spectrum of full-width at half-maximum (FWHM) more than 100 nm, which can be realized for WOLEDs.     

Excited-state absorption in a terpyridyl platinum(II) pentynyl complex

The singlet excited-state lifetime of a terpyridyl platinum(II) pentynyl complex was determined to be 268+/-87 ps by fitting femtosecond transient absorption data, the triplet excited-state lifetime was found to be 62 ns by fitting nanosecond transient absorption decay data, and the triplet quantum yield was measured to be 0.16. A ground-state absorption cross section of 2.5 x 10(-19) cm(2) at 532 nm was deduced from UV-vis absorption data. Excited-state absorption cross sections of 3.5 x 10(-17) cm(2) (singlet) and 4.5 x 10(-17) cm(2) (triplet) were obtained by using a five-level dynamic model to fit open-aperture Z scans at picosecond and nanosecond pulse widths and a variety of pulse energies.     

ESR spectral studies of a Cu(II) salicylidene tyrosine complex

A novel Schiff base derived from salicylidene and tyrosine and its copper(II) complex have been synthesized and characterized. The composition of the complex is K[CuL(Ac)] · H₂O, where L = H₁₃C₁₆NO₄. Electron spin resonance (ESR) spectra of the copper(II) complex were investigated at different temperatures and in various solvents. The second-order effect and the relaxation effect were observed in the solution spectrum at room temperature and satisfactorily explained by the spin Hamiltonian. The bonding parameters of the Cu(II) complex were calculated with spectral parameters from ESR spectra at low temperature. Its bonding characterization and stability were discussed. The result shows that both the in-plane σ-bond and the in-plane π-bond in the complex play an important role.     

Ion and polymer chain motion in a superionic sodium-poly (ethylene oxide) complex

Magnetic resonance measurements have been performed on the ion conducting complex poly(ethylene oxide)_4.5NaClO. Low temperature²³Na NMR spectra suggest a highly symmetric environment for the Na-ions as evidenced by the absence of quadrupole broadening. Proton spin-lattice relaxation measurements provide an estimate of ~4×10^?10 sec for the polymer chain motional correlation time at T = 69C. Correlation times of tumbling paramagnetic probe molecule have been extracted from EPR spectra of¹⁵N-enriched TANOL-doped complex. Changes in polymer chain mobility above T = 120C are inferred from the results and may be consistent with previous scanning calorimetry measurements.     

Sonochemical syntheses of a new nano-plate cadmium(II) coordination polymer as a precursor for the synthesis of cadmium(II) oxide nanoparticles

Nanoplates of the three-dimensional coordination polymer, {[Cd(3)(3-pyc)(4)(N(3))(2)(H(2)O)](n) (1), 3-pyc(-)=pyridine-3-carboxylate), have been synthesized by a sonochemical process and characterized by scanning electron microscopy, X-ray powder diffraction, IR spectroscopy and elemental analyses. Cadmium(II) oxide nanoparticles were prepared from thermal decomposition in oleic acid and direct calcination of compound 1 at different temperatures. The thermal stability of nano-sized compound 1 was studied by thermal gravimetric (TG) and differential thermal analyses (DTA). Results show that the size and morphology of the CdO nanoparticles are dependent upon the particles size of compound 1 and the thermolysis temperature. A decrease in the particle size of compound 1 leads to a decrease in the particle size of the CdO, while an increase in the processing temperature leads to an increase in the particle size of the produced cadmium(II) oxide nano-particles.     

Studies on Cu(II), Zn(II), Ni(II) and Co(II) complexes derived from two dipeptide Schiff Bases

Some new metal complexes of two dipeptide Schiff bases derived from salicylaldehyde and dipeptides such as glycyl-DL-alanine and glycyl-DL-phenylalanine have been synthesized and characterized by elemental analysis, molar conductance, IR, UV spectra, TG and DTA studies. The COO stretching bands in IR spectra suggest that the carboxylate acts as a monodentate group when binding with metal. The ligands are coordinated to the central metal as tetradentate ligands. The bonding sites are the carboxylate oxygen, imino nitrogen, amide nitrogen and phenolic oxygen.     

Structural investigation of mM Ni(II) complex isomers using transmission XAFS: the significance of model development

High‐accuracy transmission XAFS determined using the hybrid technique has been used to refine the geometries of bis(N‐n‐propyl‐salicylaldiminato) nickel(II) (n‐pr Ni) and bis(N‐i‐propyl‐salicylaldiminato) nickel(II) (i‐pr Ni) complexes which have approximately square planar and tetrahedral metal coordination. Multiple‐scattering formalisms embedded in FEFF were used for XAFS modelling of the complexes. Here it is shown that an IFEFFIT‐like package using weighting from experimental uncertainty converges to a well defined XAFS model. Structural refinement of (i‐pr Ni) was found to yield a distorted tetrahedral geometry providing an excellent fit, χ_r² = 2.94. The structure of (n‐pr Ni) is best modelled with a distorted square planar geometry, χ_r² = 3.27. This study demonstrates the insight that can be obtained from the propagation of uncertainty in XAFS analysis and the consequent confidence which can be obtained in hypothesis testing and in analysis of alternate structures ab initio. It also demonstrates the limitations of this (or any other) data set by defining the point at which signal becomes embedded in noise or amplified uncertainty, and hence can justify the use of a particular k‐range for one data set or a different range for another. It is demonstrated that, with careful attention to data collection, including the correction of systematic errors with statistical analysis of uncertainty (the hybrid method), it is possible to obtain reliable structural information from dilute solutions using transmission XAFS data.     

Ni（Ⅱ）,Cu（Ⅱ）,Zn（Ⅱ）的硝酸盐与氟哌酸的固态配合物的 …

由氟哌酸与Ｎｉ（Ⅱ）、Ｃｕ（Ⅱ）、Ｚｎ（Ⅱ）的硝酸盐合成了三个未见报道的固态配合物,并用元素分析、摩尔电导、红外光谱、热重分析表征了它们的组成和性质。     

Co（Ⅱ）,Ni（Ⅱ）非有机溶剂液—液萃取行为的研究

In PEG-Eriochrome cyanine R-(NH4)2SO4 system the liquid-liquid extraction behaviour of Co(II) and Ni(II) without organic solvents was investigated. We found that Ni(II) was almost extracted by PEG phase while Co(II) was not extracted in the water solutions of NaAc-HAc (pH=5) and (NH4)2SO4. Thus Co(II) was quantitatively separated from mixed solutions of Ni(II) and Co(II) ions.     

Adsorption of Hydrogels Based on Cellulose for Cu(II) and Ni(II): Behaviors and Mechanisms

Hydrogels based on cellulose-graft-poly (acrylic acid) copolymers (C-g-AA) were synthesized by graft copolymerization in a phosphoric acid solvent. Fourier transform infrared (FT-IR) spectra confirmed the structure of the C-g-AA. The adsorption behaviors of the hydrogels for Cu(II) and Ni(II) were investigated. The results showed that their adsorption capacity increased as the initial concentrations of metal ions and the pH value of the solution increased. Freundlich and Langmuir isotherm models were employed to analyze the data from batch adsorption experiments. The results indicated that there were very good correlation coefficients for their linearized equations. The maximum adsorption amounts of the hydrogels for the metal ions, based on the Langmuir model, were 182 and 200 mg/g for Cu(II) and Ni(II), respectively. When the initial concentration of metal ions was 1000 mg/g the actual adsorption amounts of the hydrogels for Cu(II) and Ni(II) were 181 and 183 mg/g, respectively.     

Phenoxide bridged tetranuclear Co(II), Ni(II), Cu(II) and Zn(II) complexes: Syntheses,characterization and fluorescence studies

A tetranucleating compartmental Schiff base ligand system has been derived from 2,6-diformyl-4-methylphenol, p-phenylenediamine and 2-aminomethylbenzimidazole. Phenoxide bridged later first row transition metal(II) complexes of this ligand have been prepared by conventional sequential route. Ligand and complexes were characterized by routine physicochemical characterizations. The mutual influence of metal centers in terms of cooperative effect on the electronic, magnetic, electrochemical and structural properties was investigated. The Schiff-bases exhibit fluorescence originating from intraligand (π→π?) transitions. Metal mediated fluorescence enhancement is observed on complexation with Zn(II), whereas metal mediated fluorescence quenching occurs in all other complexes.     

Vibrational spectra of polaprezinc,a polymeric Zn(II) complex of carnosine

Polaprezinc, the Zn(II) complex of the dipeptide carnosine (β‐alanyl histidine) presents an interesting biological and pharmacological activity, specially as an anti‐ulcer agent. The infrared and Raman spectra of this compound were recorded and briefly discussed. Some comparisons were made with related complexes and with free carnosine. The results confirm the coordination environment of the Zn(II) cation, constituted by the terminal amino N‐atom, the deprotonated amide N‐atom and one carboxylate oxygen of one dipeptide molecule and the N‐atom of the imidazole moiety of a second carnosine molecule. Copyright © 2007 John Wiley & Sons, Ltd.