Cu/SiO_2气凝胶催化剂上CO的催化氧化性能

如何消除 CO对环境造成的污染 ,是当前人们所关心的课题之一 .催化氧化是消除 CO的一种有效方法 .常用的 CO氧化催化剂多以贵金属为基础 .目前 ,对非贵金属催化剂的研究也正在进行 ,其中 ,过渡金属 Cu、Co、Fe等对 CO的氧化有较好的催化作用 .传统的过渡金属催化剂多以氧化铝为载体 ,并发展了多种制备方法 ,如化学浸渍法、溶胶凝胶法[1] 等 ;催化剂的金属活性组分也由微米级颗粒发展到纳米级超细粒子[2 ] .但对载体的研究仍集中于氧化铝 .近几年发现 ,过渡金属交换的ZSM- 5分子筛具有较高的活性和稳定性 [3 ] .二氧化硅气凝胶是一种新…     

Ir/CeO2催化剂的表征和CO氧化性能

采用浸渍法制备了Ir/CeO2催化剂,考察了催化剂的CO氧化活性。随着Ir负载量的增加,Ir/CeO2催化剂的CO氧化活性先上升后下降,当Ir的负载量为1%时,催化剂的活性最高。Ir/CeO2催化剂中Ir以IrO2的形式存在,当低负载量(≤1%)时以高分散形式存在;高负载量(>1%)时以晶相IrO2的形式存在。随着Ir负载量增加,Ir粒子逐渐变大,反应比速率和反应转换频率(TOF)逐渐下降,表明小粒子上具有更高的CO反应活性。同时也发现金属态Ir催化剂的CO氧化活性高于氧化态IrOx催化剂。     

CuO Catalysts Supported on Porous TiO2 Microspheres for Low-Temperature CO Oxidation

The porous TiO₂ microspheres were prepared by the reversed-phase suspension polymerization and sol-gel method using reversed-phase suspension droplets as the templates. The CO oxidation catalytic properties of the CuO/TiO₂ catalysts prepared by hydrothermal method and impregnation method were extensively investigated. The structure of CuO/TiO₂ catalysts was determined by TG-DTA, XRD, TEM, and XPS. The results indicated that the redox capacity of CuO/TiO₂ was greatly depended on the aqueous solution concentration of Cu(NO₃)₂ used in the preparation of CuO/TiO₂ and the calcination temperature of the CuO/TiO₂ catalysts.     

Structure and Properties of Sol—Gel Derived CuNiMnZrO2 Catalysts for CO Hydrogenation

Two CuNiMnZrO2 catalysts (crystallized or non-crystallized) were prepared by co-hydrolyzing zirconium n-propoxide with Cu(NO3)2, Mn(NO3)2 and Ni(NO3)2 in an ethanol solution in the presence of diglycol. The physical and chemical properties of the catalysts were characterized using BET, XRD,TEM, XPS and CO-DRIFT techniques. It was found that the non-crystallizied CuNiMnZrO2 catalyst demonstrated highly dispersed active phases and high activity for CO adsorption, which resulted in good performance for synthesis of higher alcohols in CO hydrogenation compared to crystallized CuNiMnZrO2.     

Thermally Induced Phase Transformation on 12-Tungstophosphoric Acid/ZrO2 Sol-Gel

Zirconium (IV)-n-butoxide and tungstophosphoric acid (WP) were co-gelled at pH 3, 5 and 7 with HCl acid, C₂H₄O₂ acid and NH₄OH, respectively. Pyridine adsorption bands at 1610 and 1442 cm^–1 corresponding to Lewis acidic sites were observed by FTIR spectroscopy. Acidity determined by ammonia thermodesorption shows values around 1100 mol of NH₃/g, which correspond to solids showing super acidity. It was found that the incorporation of WP to gelling zirconia delay the formation of tetragonal zirconia. Raman spectroscopy shows the stabilization of the Keggin structure on zirconia thermally treated at 400°C.     

P123软模板对CuO-CeO2结构及其CO催化氧化性能的影响

采用软模板水热法制备了不同Cu/Ce物质的量之比的CuO-CeO₂(n_Cu:n_Ce=1:9、2:8、3:7、4:6、5:5、6:4、7:3)催化剂。考察了n_Cu:n_Ce和制备方法(软模板水热法和无模板共沉淀法)对CuO-CeO₂催化剂低温催化氧化CO性能的影响,并采用XRD、N₂-吸附脱附、TEM、H₂-TPR和XPS等表征手段对催化剂的结构、氧化还原特性和表面化学状态等进行了分析。结果表明,随着nCu:nCe的增加,CuO-CeO₂催化剂的CO催化氧化活性先升高后降低。当n_Cu:n_Ce=5:5时,催化剂在100℃时CO转化率即达到90%以上。采用软模板水热法制备的CuO-CeO₂催化剂大的比表面积、狭窄的孔道分布结构、活性CuO物种高的分散状态和CuO与CeO₂之间存在强相互作用是其具有优异的CO催化氧化活性的主要原因。     

Pt/TiO2催化剂上CO氧化反应动力学研究

利用沉积沉淀法制备了Pt/TiO₂催化剂, 将其在不同温度下焙烧, 以得到不同颗粒尺寸的Pt. 并将这些样品用于CO催化氧化反应以及反应动力学研究. 结果表明: 焙烧温度对催化剂有明显影响, Pt 颗粒尺寸随着焙烧温度的升高而增加; 与此同时, CO催化活性随焙烧温度的升高呈先增加后降低的趋势, 其中, 400℃焙烧的样品表现出最高的催化活性. 反应动力学结果表明, 催化剂上CO氧化反应表观速率方程为r=5.4×10^-7p_CO^0.17p_O2^0.36,说明在该催化剂上CO氧化遵循Langmuir-Hinshelwood机理. 同时, 对催化剂进行了CO化学吸附红外光谱和O₂化学吸附表征. 结果表明, 随着焙烧温度的升高, 催化剂上CO和O₂吸附量均呈现先升高后降低的趋势, 这与反应结果和反应动力学方程一致, 说明反应受到催化剂表面上CO和O₂吸附浓度的影响. 而在400℃焙烧的催化剂上, CO和O₂吸附量均最高, 因此其反应活性也最好. 这可能是焙烧过程影响了Pt 和TiO₂之间的相互作用引起的.     

Catalytic Combustion of Methane on Fe-TiO2 Catalysts Prepared by Sol-Gel Method

Two different series of titania-supported iron catalysts prepared by the sol-gel method have been characterised and tested in the combustion of methane at atmospheric pressure. In each series, the effect of metal loading (1, 5 and 10 wt%) and gelation pH (3 and 9) were studied. Characterisation data of calcined catalysts, carried out by specific area measurement, TPR, X-ray diffraction, XPS and EPR revealed no significant changes in metal dispersion. The catalytic activity of the solids were evaluated in the combustion of methane under stoichiometric mixture of CH₄/O₂ from 473 K up to the temperature required for total combustion. The best performance was shown by catalysts having 5 wt.%, which is ascribed to a balance of factors like the presence of a sufficient concentration of iron at the surface, achievement of relatively high dispersion state for iron and the presence of Fe⁺³ ions incorporated to the lattice of titania.     

制备方法对CuO/CeO_2-ZrO_2催化CO低温氧化活性的影响

采用微波加热分解法(一步法)和微波加热处理共沉淀+浸渍法(两步法)制备了CuO/CeO2-ZrO2催化剂,并对其进行了X射线衍射、低温氮气吸附/脱附和程序升温还原等表征,采用色谱流动法考察了催化剂的催化CO低温氧化性能.结果表明,一步法比两步法更有利于使催化剂表面CuO高度分散,CuO与CeO2-ZrO2间的相互作用更强,CuO更容易被还原,从而具有更高的催化CO氧化活性.与CeO2-ZrO2有相互作用的高分散和小颗粒CuO有利于催化剂活性的提高,与CeO2-ZrO2无相互作用的大颗粒CuO对催化剂的活性有抑制作用.     

Synthesis and Characterization of Sol-Gel Cu-ZrO2 and Fe-ZrO2 Catalysts

Fe-ZrO₂ and Cu-ZrO₂ xerogels were prepared by a sol-gel method. The effect of the hydrolysis catalyst during the gelation step, namely H₂SO₄ or NH₄OH, on the properties of the resulting materials was investigated by XRD, BET, TGA/DTA, TPD of ammonia, FTIR, and TPR. Fe-ZrO₂ and Cu-ZrO₂ xerogels, with sulfuric acid introduced as the hydrolysis catalyst, mainly crystallyzed in the tetragonal phase and exhibited larger surface area and acid amount than those obtained with NH₄OH. Ammonia TPD shows that copper promoted sulfated zirconia is the most acidic material. TGA and FTIR reveal that under oxidizing conditions sulfated zirconia promoted with iron and copper retains more sulfate species than unpromoted sulfated zirconia. Regardless of the hydrolysis catalyst employed, copper promoted catalysts calcined at 600°C, contain a large fraction of copper oxide specieseasily reduced at low temperatures. These copper oxide species are believed to have different environment and interactions with the surface oxygen vacancies of the zirconia support. A FeO-like phase appears to be the most probable one after reduction of Fe-ZrO₂ catalysts prepared with NH₄OH as the hydrolysis catalyst. The formation of Fe° species may be hindered by the high dispersion and interaction of Fe²⁺ ions with the zirconia support. On the other hand, the reduction peaks of iron oxide and sulfate species exhibit a considerable overlap in the TPR profiles of sulfated Fe-ZrO₂ samples. Hence, the nature of the supported phase in the latter samples is rather uncertain.     

Low temperature CO oxidation on Au/TiO2 sol-gel catalysts

A comparative study on Au/TiO₂catalysts prepared by impregnation with HAuCl₄of commercial TiO₂ or by impregnation of sol-gel derived TiO₂has been carried out during CO oxidation. Specific surface areas and mean Au particle of 49 and 74 m²/g and 35 and 25 Å were obtained for impregnated commercial TiO₂ and sol-gel preparations, respectively. XRD patterns shown that in sol-gel derived TiO₂ only anatase phase was identified, while in commercial TiO₂ anatase and rutile phases co-exist. Titania support effect on Au activity for the oxidation of CO has been observed. The light-off during the reaction on Au/TiO₂initiates at 50°C, whereas for commercial impregnated TiO₂ catalyst the light-off initiates at 200°C.     

Preparation,Characterization, and Catalytic Behavior of Nanostructured Mesoporous CuO/ZrO2 Catalysts for Low-Temperature CO Oxidation

High-surface area mesoporous 20 mol% CuO/ZrO₂ catalyst was prepared by a surfactant-assisted method of nanocrystalline particle assembly, and characterized by x-ray powder diffraction (XRD), N₂ adsorption, transmission electron microscopy (TEM), H₂-TPR, TG-DTA, and x-ray photoelectron spectra (XPS) techniques. The catalytic properties of the CuO/ZrO₂ nanocatalysts calcined at different temperature were evaluated by low-temperature carbon monoxide oxidation using a CATLAB system. The results showed that these mesoporous nanostructured CuO/ZrO₂ catalysts were very active for low-temperature CO oxidation and the CuO/ZrO₂ catalyst calcined at 400°C exhibited the highest catalytic activity.     

Pt/MOx(M=Ni,Fe,Co,Ce)催化剂上CO氧化反应中抗H2O与CO2的性能研究

我们研究了4种负载型Pt催化剂（1Pt/NiO、1Pt/FeO_x、1Pt/Co₃O₄和Pt/CeO₂）上不同反应条件下CO氧化活性及抗H₂O和CO₂性能.发现反应气氛中CO₂的加入与CO形成了竞争吸附,并在催化剂表面形成了碳酸盐物种堵塞了活性位,从而导致催化剂失活.反应气氛中H₂O的加入对1Pt/CeO₂催化剂的活性有所抑制,但对1Pt/FeO_x、1Pt/NiO和1Pt/Co₃O₄催化剂的活性却有促进作用.在1Pt/FeO_x和1Pt/CeO₂催化剂上的分步反应实验和动力学研究表明,尽管H₂O的加入在两种催化剂上均与CO形成了竞争吸附,但在1Pt/FeO_x催化剂上H₂O在载体表面解离形成的羟基更易与CO反应,开辟了新的反应途径,从而提高了反应性能.此外,H₂O的加入能有效分解该催化剂上的碳酸盐物种,从而保持了其稳定性.     

Low-Temperature CH4 Total Oxidation on Catalysts Based on High Surface Area SnO2

Pure SnO₂, sulfated SnO₂-SO₄ ^2- and Pd supported on SnO₂ and SnO₂-SO₄ ^2- were prepared from SnO₂ precursor with high surface area, and used for CH₄ deep oxidation. The catalysts were characterized by means of N₂-BET, XRD, TG-DTA, XPS and TPD. SnO₂-SO₄ ^2- shows higher activity than SnO₂, due to the presence of more active oxygen species, superacid sites and its higher BET surface area. Pd/SnO₂ and Pd/SnO₂-SO₄ ^2- display essentially the same activity to each other, while it is much higher than the activity on SnO₂ and SnO₂-SO₄ ^2-. The main reason is ascribed to the concerted action between Pd and the supports.     

CO and Methane Oxidation Over CeXZr1-XO2 Mixed Oxide Supported PdO Catalysts

In this paper, the Ce_XZr_1-XO₂-supported PdO catalysts were prepared and the effect of Ce/Zr ratio on catalytic activity for CO and methane oxidation was studied, both activity and the reduction behavior of catalyst depend on the Ce/Zr ratio. The reduction behavior of those catalysts was characterized by means of TPR.     

酸化膨润土负载金催化剂用于CO氧化

用盐酸和硫酸对膨润土（Ben）进行改性处理,采用浸渍法（IMP）、沉积-沉淀法（DP）和阳离子吸附法(CA)制备改性膨润土负载的金催化剂,以CO氧化作为探针反应对催化剂的催化性能进行了研究,采用BET、XRD、TEM和TPD等对催化剂进行表征。 结果表明,经过简单的酸处理后的膨润土比表面积和孔体积有了大幅度的提高,硫酸酸化的膨润土作为载体较之盐酸酸化土更容易得到活性较高的金催化剂,XRD粒径计算结果和TEM观察结果证明,硫酸酸化的膨润土作为载体相比盐酸酸化土可以得到Au颗粒度更小的催化剂。 不同制备方法中,阳离子吸附法能较好的将Au负载于膨润土载体上,得到小颗粒的金催化剂,且在吸附48 h、450 ℃焙烧、150 ℃下H2还原的预处理条件下得到的催化剂活性最好。     

制备方法对CuO-CeO2/ZrO2催化CO氧化性能的影响

以ZrO2为载体、采用不同的浸渍次序制备了3种CuO-CeO2/ZrO2催化剂并在不同的温度(500,650和800℃)下进行焙烧,利用X射线衍射(XRD)、程序升温还原(H2-TPR和CO-TPR)及CO程序升温脱附(CO-TPD)技术对所制备的催化剂进行了表征,并采用色谱流动法考察了其催化CO低温氧化反应性能。结果表明,当焙烧温度为650℃时,3种催化剂的CO催化氧化活性均最佳,且三者的催化活性大小顺序为:CuO/CeO2/ZrO2>CuO-CeO2/ZrO2>CeO2/CuO/ZrO2。结合催化剂的表征和活性测试结果,我们认为高分散的CuO是CO的吸附中心,有利于CO的低温氧化反应,而大颗粒的CuO几乎对CO没有吸附作用,不利于CO的低温氧化反应。在3种催化剂中,CuO/CeO2/ZrO2催化剂具有最佳的低温还原特性和最大的CO2脱附峰面积,相应地具有最佳的催化氧化活性。     

Thermal Stability of Pt/Al2O3 Catalysts Prepared by Sol-Gel

A series of Pt/Al₂O₃ catalysts were prepared using a sol-gel method. The influence of several parameters used in the synthesis including: metal content, identity of the metal precursor, and the water/alkoxide ratio on the structural properties of the fresh (dried) and calcined samples were studied. It was found that the BET surface area decreased with an increase in the platinum content. A surface area of 500 m²/g was obtained following calcination at 773 K. The structure of fresh samples as determined by FTIR corresponded to that of a pseudoboehmite structure. Samples prepared using a water/alkoxide ratio (H₂O/ATB) of 9 showed a well-defined, uniform pore size distribution following calcination at 773 K. Metal dispersions comparable to those obtained using impregnation methods were obtained. Aging studies (calcination at 873 K for 24 h) performed on these catalysts, exhibited sintering behavior which were similar to Pt/Al₂O₃ catalysts prepared by other methods. The sample prepared using a H₂O/ATB ratio of 9 had the highest surface area and was more thermally resistant towards metal sintering. A bimodal metal particle size distribution was observed: some particles exhibited sintering while others of similar size showed a greater thermal stability to sintering. The sample having the largest surface area and the highest thermal stability following thermal treatment was a consequence of a more condensed structure and a higher pore roughness obtained after drying the gel. This enabled the formation of an alumina structure which was more amorphous and limited aggregation of platinum particles due to surface diffusion within the pore structure.     

Effect of La2O3 on Catalytic Performance of Au/TiO2 for CO Oxidation

Pure TiO₂ and La-doped TiO₂ were prepared by the sol-gel method. Au was supported on TiO₂ by the deposition-precipitation (DP) method, and its catalytic activity for CO oxidation was tested. The results showed that doping La in Au/TiO₂ could improve its catalytic activity obviously for CO oxidation. The analyses of X-ray diffraction (XRD), temperature-programmed desorption (TPD), and Brunauer-Emmett-Teller (BET) surface area further showed that the presence of La in TiO₂ not only increased its surface area and restrained the growth of TiO₂ crystallites, but could also enhance the microstrain of TiO₂. In terms of O₂-TPD, a new adsorbed species O⁻ appeared on the surface of La-doped TiO₂. The results of in-situ Fourier transform-infrared (FT-IR) spectroscopy illustrated that the high activity of Au/La₂O₃-TiO₂ was attributed to the presence of La promoting the reactivity of CO adsorbed on the Au site and the formation of the second active site on the surface of TiO₂     

CrOx/SiO2催化剂上丙烷在CO2气氛中脱氢反应的研究

采用XRD、UV-vis DRS、ESR和微分吸附量热等技术,考察了铬担载量分别为2.5、5和10wt%的CrO_x/SiO₂催化剂的结构、表面性质和氧化还原性能。结果表明,催化剂表面上存在多种Cr的氧化态和聚集形式。随着Cr担载量从2.5wt%到10wt%的逐渐增大,催化剂表面占主导地位的Cr物种由CrO₃单体转为多聚CrO₃和Cr₂O₃晶相。在CO₂气氛中催化剂对丙烷转化率和丙烯选择性的大小顺序为2.5wt%CrO_x/SiO₂>5wt%CrO_x/SiO₂>10wt%CrO_x/SiO₂,反应过程中的原位ESR和UV-visDRS测定结果表明,催化剂表面的反应活性中心为Cr⁵⁺,Cr⁵⁺可由催化剂预处理过程中Cr³⁺的氧化及丙烷反应过程中CrO₃单体的还原产生,在反应中CO₂可使Cr³⁺重新氧化为Cr⁵⁺.