飞机跑道胶痕的自动识别系统设计与实现

为了减轻机场跑道除胶工作人员的劳动强度,提高除胶工作效率,文章提出了一种基于机器视觉的胶痕自动查找和识别方法,设计了基于ARM单片机控制的图像无线采集和基于PC机控制的图像接收、图像预处理和图像识别系统。文章通过分析预处理后的数据特点,确定了基于细胞神经网络算法的胶痕识别算法,然后在MATLAB仿真环境下确定了该算法的最优模型和参数,最后在Visual C++ 6.0环境下完成了该算法的程序编译,调试并完成了对胶痕的自动识别过程。理论仿真和程序测试的结果证明了文章提出的方法在胶痕自动识别系统中的可行性,也为机场特种设备的无人化和智能化提供了参考。     

SrBi2Ta2O9/Bi4Ti3O12复合铁电薄膜的制备与特性研究

采用溶胶凝胶工艺在p-Si衬底上制备了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合铁电薄膜. 研究了SrBi₂Ta₂O₉/Bi₄Ti₃O₁₂复合薄膜的微观结构与生长行为、铁电性能和疲劳特性. 研究表明: Si衬底Bi₄Ti< 关键词： 2Ta₂O₉')" href="#">SrBi₂Ta₂O₉ 4Ti₃O₁₂')" href="#">Bi₄Ti₃O₁₂ 复合铁电薄膜 溶胶凝胶工艺     

一种车辆状态通用自动监测装置设计与实现

当前装备车辆底盘数据大都通过仪表盘进行显示,而没有对数据进行采集和存储,造成对车辆的基本状态无法进行有效的评估和故障趋势分析;针对这种情况,设计一种对车辆底盘运行参数进行采集和存储的装置,通过一个通用的多PIN接口与车辆仪表盘信号线相连,采用高速AD芯片、高速主控芯片和RS485通讯接口实现对仪表盘接线输出信号的采集、计算与数据的传输存储;应用表明,此装置解决了多种车辆底盘参数的采集记录问题,具有广泛的推广应用价值。     

Structure of Artificial Grain Boundaries in Sapphire Bicrystals with Intermediate Layers

The structure of the artificial grain boundaries in Al₂O₃ bicrystals withY₃Al₅O₁₂ and Y-stabilizedZrO₂ (Y-ZrO₂) intermediate layers was studiedwith high resolution electron microscopy, electron diffraction and energydispersive X-ray analysis. TheY₃Al₅O₁₂ intermediate layer wasfound to be polycrystalline with three different orientation relationshipsbetween the ₂O₃ and theY₃Al₅O₁₂. The structure of theY₃Al₅O₁₂/₂O₃ interfaces is described.Also₂O₃ bicrystals with an Y-ZrO₂/₂O₃/Y-ZrO₂/₂O₃/Y-ZrO₂intermediate layer, prepared at two different temperatures, werestudied.Recry stallization of the intermediate layers occurred during thesolid phase intergrowth of the ₂O₃ bicrystalsparts and only an Y-ZrO₂ layer was found as intermediatelayer. The misorientation between the consecutive Y-ZrO₂grains was less than 1.5°. Misfit dislocations and atomic height stepsdecorate the Y-ZrO₂/₂O₃interface.     

Correlation of fluctuation field and temperature coefficient of coercivity in a CoCrPtB thin film

The effect of the ratio of fluctuation field (H_f) to coercivity (H_c) on the temperature coefficient of coercivity [α(H_c)] was investigated for Co₅₅Cr_15.5Pt₂₈B_1.5/Co₆₃Cr₃₇/Cr, Co₆₉Cr₁₉Pt₉Ta₃/Cr, and Co₈₆Cr₁₀Ta₄/Cr thin films (longitudinal recording media) with very small average grain volume (V_phy). α(H_c) increases markedly with increase in temperature between near 250 and 350 K for Co₅₅Cr_15.5Pt₂₈B_1.5/Co₆₃Cr₃₇/Cr thin films. α(H_c) is approximately proportional to the ratio H_f/H_c for all thin films, as in the case of advanced data backup tapes prepared from ultrafine particles. α(H_c) and the ratio H_f/H_c increase as V_phy decreases. Smaller H_f/H_c values are necessary for small α(H_c) values, which is very important for the thermal stability of high-density recording media with very small V_phy.     

故障注入技术在机载计算机模拟量采集中的应用

近年来航空武器的功能性能快速提高,机载计算机处理能力也越来越强。接口模块作为处理多种接口信号的重要部件,在机载计算机中起着至关重要的作用。文中结合故障注入技术,在以往常用模拟量采集电路基础上,设计了模拟量激励产生电路,实现模拟量采集电路的故障注入,结合测试软件完成模拟量采集电路的检测,达到提高机载计算机的测试性的目标。     

Catalytic effect of water,water dimer,water trimer,HCOOH, H2SO4, CH3CH2COOH and HN(NO2)2 on the isomerisation of HN(NO2)2 to O2NNN(O)OH: a mechanism study

In this article, the isomerisation mechanisms of HN(NO₂)₂ to O₂NNN(O)OH without and with catalyst X (X = H₂O, (H₂O)₂, (H₂O)₃, HCOOH, H₂SO₄, CH₃CH₂COOH and HN(NO₂)₂) have been investigated theoretically at the CBS-QB3 level of theory. Our results show that the catalyst X (X = H₂O, (H₂O)₂, (H₂O)₃, HCOOH, H₂SO₄ and CH₃CH₂COOH) shows different positive catalytic effects on reducing the apparent activation energy of the isomerisation reaction processes. Such different catalytic effects are mainly related to the number of hydrogen bonds and the size of the ring structure in X (X = H₂O, (H₂O)₂ and (H₂O)₃)-assisted transition states, as well as different values of pK_a for H₂SO₄, HCOOH and CH₃CH₂COOH. Very interesting is also the fact that H₂SO₄-assisted reaction is the most favourable for the hydrogen transfer from HN(NO₂)₂ to O₂NNN(O)OH, due to the smallest pK_a (?3.0) value of H₂SO₄ than H₂O, HCOOH, H₂SO₄ and CH₃CH₂COOH, and also because of the largest ∠X???H???Y (the angle between the hydrogen bond donor and acceptor) involved in H₂SO₄-assisted transition state. Compared to the self-catalysis of the isomerisation mechanisms of HN(NO₂)₂ to O₂NNN(O)OH, the apparent activation energy of H₂SO₄-assisted channel also reduces by 9.6 kcal?mol^?1, indicating that H₂SO₄ can affect the isomerisation of HN(NO₂)₂ to O₂NNN(O)OH, most obvious among all the catalysts H₂O, (H₂O)₂, (H₂O)₃, HCOOH, H₂SO₄, CH₃CH₂COOH and HN(NO₂)₂.     

Valence states of copper atoms in cuprates determined from the change in the electron-capture constant of 64Cu

The change in the ⁶⁴Cu electron-capture constant for the compounds Cu₂O, YBa₂Cu₃O₇, YBa₂Cu₃O₆, Nd₂CuO₄, Nd_1.8Ce_0.2CuO₄, La₂CuO₄, La_1.7Sr_0.3CuO₄, Tl₂Ba₂CaCu₂O₈, and Bi₂Sr₂CaCu₂O₈ has been measured. It is concluded that the copper in YBa₂Cu₃O₇, Nd₂CuO₄, La₂CuO₄, La_1.7Sr_0.3CuO₄, Tl₂Ba₂CaCu₂O₈, and Bi₂Sr₂CaCu₂O₈ is exclusively divalent, whereas in Cu₂O, YBa₂Cu₃O₆, and Nd_1.8Ce_0.2CuO₄ univalent copper is present. Fiz. Tverd. Tela (St. Petersburg) 39, 1793–1794 (October 1998)     

Ternary compounds and isothermal section in Lu–Fe–Ga ternary system at 773 K

The isothermal section of the Lu–Fe–Ga ternary system at 773?K was investigated and constructed based on X-ray powder diffraction analysis. Thirteen binary compounds, Lu₂Fe₁₇, Lu₆Fe₂₃, LuFe₂, LuGa₃, LuGa₂, Lu₃Ga₅, LuGa, Lu₃Ga₂, Lu₅Ga₃, Fe₃Ga, Fe₆Ga₅, Fe₃Ga₄, FeGa₃, nine ternary solid solutions, T₁-LuFe_2–1.43Ga_0–0.57, T₂-LuFe_1.34–0.92Ga_0.68–1.08, T₃-LuFe_0.52–0.26Ga_1.48–1.74, T₅-LuFe_2.04–1.72Ga_0.96–1.28, T₆-Lu₆Fe_23–21.4Ga_0–1.6, T₇-Lu₂Fe_17–14.5Ga_0–3.5, T₈-Lu₂Fe_12.9–8.1Ga_4.1–8.9, T₉-LuFe_6.8–5.5Ga_5.2–6.5, T₁₀-LuFe_5.2–4.5Ga_6.8–7.5, and two ternary compounds, T₄-LuFe_2.35Ga_0.65 and T₁₁-Lu₂FeGa₈ have been confirmed. The structures of the five new ternary compounds or solid solution T₂, T₃, T₄, T₅ and T₈ are determined by Rietveld refinement method.     

The study of phase,microstructure, and magnetocaloric properties in LaFe11.6*xSi1.4B0.1 alloys

The effect of Fe on the phase and magnetocaloric property of LaFe_11.6*xSi_1.4B_0.1 alloys with x = 1.0–1.4 have been studied. The results show that the excess of Fe will make the α-Fe phases increase, but the easy corrosion LaFeSi phase reduces in LaFe_11.6*xSi_1.4B_0.1 alloys. All LaFe_11.6*xSi_1.4B_0.1 alloys keep the first-order magnetic phase transition. The saturation magnetizations of LaFe_11.6*xSi_1.4B_0.1 alloys with x > 1 are much higher than LaFe_11.6Si_1.4B_0.1 alloy under 2T magnetic field. This results in the maximum isothermal magnetic entropy changes, and the relative cooling power of LaFe_11.6*xSi_1.4B_0.1 alloys is bigger than for LaFe_11.6Si_1.4B_0.1 alloys.     

The system Na2CO3–CaCO3–MgCO3 at 6 GPa and 900–1250°C and its relation to the partial melting of carbonated mantle

In order to constrain the Na₂CO₃–CaCO₃–MgCO₃ T–X diagram at 6?GPa in addition to the binary and pseudo-binary systems we conducted experiments along the Na₂CO₃–Ca_0.5Mg_0.5CO₃ join. At 900–1000°C, melting does not occur and isothermal sections are presented by one-, two- and three-phase regions containing Ca-bearing magnesite, aragonite, Na₂CO₃ (Na₂) and Na₂(Ca_1–0.9Mg_0-0.1)_3-4(CO₃)_4-5 (Na₂Ca_3-4), Na₄(Ca_1–0.6Mg_0–0.4)(CO₃)₃ (Na₄Ca), Na₂(Ca_0-0.08Mg_1–0.92)(CO₃)₂ (Na₂Mg) phases with intermediate compositions. The minimum melting point locates between 1000°C and 1100°C. This point would resemble that of three eutectics: Mgs–Na₂Ca₃–Na₂Mg, Na₂Mg–Na₂Ca₃–Na₄Ca or Na₂Mg–Na₄Ca–Na₂, in the compositional interval of [45Na₂CO₃·55(Ca_0.6Mg_0.4)CO₃]–[60Na₂CO₃·40Ca_0.6Mg_0.4CO₃]. The liquidus projection has seven primary solidification phase regions for Mgs, Dol, Arg, Na₂Ca₃, Na₄Ca, Na₂ and Na₂Mg. The results suggest that extraction of Na and Ca from silicate to carbonate components has to decrease minimum melting temperature of carbonated mantle rocks to 1000–1100°C at 6?GPa and yields Na-rich dolomitic melt with a Na# (Na₂O/(Na₂O?+?CaO?+?MgO))?≥?28?mol%.     

Weak ferromagnetism in BiFeO3 doped with titanium

The Bi_1−xA_xFe_1−xTi_xO₃ (A—Ca, Sr, Pb, Ba) and BiFe_1−xTi_xO_3+δ systems have been studied using X-ray, neutron powder diffraction and magnetization measurements in a magnetic field up to 14 T. It was found that all Bi_1−xA_xFe_1−xTi_xO₃ solid solutions are rhombohedral up to x=0.3. In the case of BiFe_1−xTi_xO_3+δ the rhombohedral distortion preserved up to x=0.11. A homogeneous weakly ferromagnetic state was found for Bi_1−xCa_xFe_1−xTi_xO₃ (0.15≤x≤0.25) and BiFe_1−xTi_xO_3+δ (0.06≤x≤0.11), probably due to magnetoelectric interactions, whereas Bi_1−xA_xFe_1−xTi_xO₃ (A—Sr, Pb, Ba) compounds above doping level x>0.1 seem to be collinear antiferromagnets.     

Influence of anionic substitution on phase transitions in Cu6PS5I1− x Cl x mixed crystals

Cu₆PS₅I_{1? ?} ? _x Cl _x mixed crystals were grown using chemical vapour transport. Isoabsorption studies of optical absorption edge and optical polarization measurements were performed in the temperature range 77–320?K. The influence of anionic I?→?Cl substitution on the phase transitions in Cu₆PS₅I_{1? ?} ? _x Cl _x mixed crystals is studied. Compositional dependence of the phase-transition temperatures is obtained and the x,T-diagram for Cu₆PS₅I_{1? ?} ? _x Cl _x mixed crystals is constructed.     

CH3NH3 + as a quantum and classical rotor

Spin-lattice relaxation time T ₁ is determined for protons in three polycrystals (CH₃NH₃)₅Bi₂Cl₁₁, (CD₃NH₃)₅Bi₂Cl₁₁ and (CH₃ND₃)₅Bi₂Cl₁₁. The temperature dependence of the relaxation times obtained for (CH₃NH₃)₅Bi₂Cl₁₁ and (CD₃NH₃)₅Bi₂Cl₁₁ are interpreted as a result of correlated motions of the three-proton groups of the monomethylammonium cation. ²H NMR lines of (CD₃NH₃)₃Sb₂Br₉ have been recorded between 5 K and 291 K using solid echo method. The ²H NMR line shape analysis shows that characteristic shape of tunnelling methyl group appears at about 25 K and coming down with temperature up to 5 K is more distinct. From theoretical calculation, it has been found that in the quadrupolar constants is 161.3 kHz and tunnelling frequency is above 3 MHz.     

IR-Spectra of M2UO2F4.H2O Complexes

This work is devoted to the study of and Rb₂UO₂F₄.H₂O and Cs₂UO₂F₄. H₂O IR-spectra with the aim of obtaining a set of vibration frequencies characterising M₂U0₂F₄.H₂O complexe elucidating the role and nature of water bonds in the structures of the above-mentioned compounds; and receiving preliminary information on the structure of M₂UO₂F₄.H₂O. The investigated compounds were synthesized in accord with our previous paper¹. M₂UO₂D₂O and M₂UO₂F₄.HDO were obtained by recrystallizing M₂UO₂F₄.H₂O from D₂O and HDO respectively     

Bi2O3-B2O3-BaO玻璃的制备及其近红外发光性能的研究

采用高温熔融法制备了xBi₂O₃-50B₂O₃-(50-x)BaO玻璃, 测定了样品玻璃的近红外光区的发射谱、荧光寿命以及Raman光谱. 在808 nm波长光的激发下, 50Bi₂O₃-50B₂O₃二元玻璃中未观察到近红外发光; 随体系中BaO的加入, 当x为40, 45以及49时, 玻璃样品中观察到了近红外宽带发光现象; BaO含量进一步增加, 当x=10–30时, 近红外发光现象消失; 而当玻璃中Bi浓度很低时, 在0.5Bi₂O₃-50B₂O₃-50BaO及1Bi₂O₃-50B₂O₃-50BaO玻璃中发现了近红外发光现象, 且存在多个发光峰. 对铋离子近红外发光机理进行了初步的探讨.     

Effect of conduction band nonprabolicity on the Rashba spin splitting of AlGaN/GaN QWs

By using the perturbation expansion method and self-consistent iterative method, we evaluate the effect of the conduction band nonprabolicity on the wave vector (k_t) dependent Rashba coefficient (α) and nonlinear Rashba spin splitting (ΔE) in the Al_0.5Ga_0.5N/GaN quantum well (QW). The effective mass (energy) under the first order approximation m_t1 (E_k1) is in proximity to the iterative result m_tp (E_kp) and m_t1>m_tp, E_k1<E_kp, showing the higher order contributions to m_t (E_k) are small. The sign of the nonparabolic correction to E_k is just opposite to that of the correction to m_t. The increase of α and ΔE due to the conduction band nonparabolicity reaches about 3% at k_t=1 nm⁻¹. Around the left heterointerface, the probability density is high and E_k0>E_kp>E_k1, so α₀<α_p<α₁, ΔE₀<ΔE_p<ΔE₁. With increasing k_t, α decreases, and ΔE increases slowly. For small k_t, α₀ (ΔE₀), α₁ (ΔE₁) and α_p (ΔE_p) are nearly the same. While for large k_t, the difference between α₀ and α₁ (α_p) increases rapidly, but the difference between ΔE₀ and ΔE₁ (ΔE_p) increases slowly.     

Composition and superconductivity in single layer Bi-2201 phases

Several materials with nominal 2201 composition were prepared from various systems Bi_2+xSr_2-xCuO_6+z, Bi₂Sr_2-xCuO_6+z, Bi_2-xPb_xSr₂O_6+z, Bi_2.1-xPb_xCuO_6+z,Bi₂Sr_2-yLa_yCuO_6+z, Bi_1.9Pb_0.1Sr_2-yLa_yCuO_6+z, Bi_2-xPb_xSr_1.6La_0.4CuO_6+z and Bi_2.1-xPb_xSr_1.5La_1.4CuO_6+z in different gas atmospheres. According to the structural investigations the 2201 phase shows solid solution behaviour. However, irrespectively of the method of preparation the appearance of superconductivity is confined to multiphase material. Furthermore, the superconducting volume fraction is uniformly as low as ? 3%. The observed presence of trace superconductivity is easily explainable by small admixtures of superconducting foreign phases and in disagreement with the assumption of intrinsic superconducting properties of the Bi based 2201 phase.     

Measurement of L X-ray fluorescence cross sections and relative intensities for some elements in the atomic range 78 ≤ Z ≤ 92

The L X-ray fluorescence cross sections (σ_Ll, σ_Lα, σ_Lη, σ_Lβ, σ_Lβ6, σ_Lβ2,₄, σ_Lβ1,₃, σ_Lβ9,10, σ_Lγ, σ_Lγ1, σ_Lγ2,3, σ_Lγ4 and σ_Lγ5) and relative intensities (I_Lα, I_Ll, I_Lη, I_Lβ, I_Lβ6, I_Lβ2,4, I_Lβ1,3, I_Lβ9,10, I_Lγ, I_Lγ1, I_Lγ2,3, I_Lγ4 and I_Lγ5) for some elements in the atomic range 78 ≤ Z ≤ 92 have been measured at 59.54 keV photons energies from an Am-241 point source. The L X-rays emitted by samples have been counted by a Si(Li) detector. The L X-ray fluorescence cross sections and relative intensities have been also calculated theoretically by using atomic parameters. The measured values have been compared with the theoretical values.     

Size-dependent microstructure and europium site preference influence fluorescent properties of Eu-doped Ca10(PO4)6(OH)2 nanocrystal

In this study, Eu³⁺-doped nanocrystalline Ca₁₀(PO₄)₆(OH)₂ (Ca_10−xEu_x(PO₄)₆(OH)₂) with different particle sizes have been prepared by the thermal decomposition of precursors. Size-dependent microstructure could be observed in nanocrystalline Ca_10−xEu_x(PO₄)₆(OH)₂. The lattices of Ca_10−xEu_x(PO₄)₆(OH)₂ nanocrystals were more distorted in comparison with the bulk, and the smaller the particle size, the more distorted the lattices. Room temperature photoluminescence showed europium site preference was also size-dependent, with the majority of Eu³⁺ ions occupying Ca(II) sites in the bulk, but more and more Eu³⁺ ions occupying Ca(I) sites in Ca_10−xEu_x(PO₄)₆(OH)₂ with decreasing particle size. Fluorescent properties of Ca_10−xEu_x(PO₄)₆(OH)₂ were considered to be influenced by both microstructure and site preference of Eu³⁺ ions. An abnormal strong intensity of ⁵D₀-⁷F₀ transition was observed in bulk and larger Ca_10−xEu_x(PO₄)₆(OH)₂ nanocrystals, but the relative intensities of ⁵D₀-⁷F₀ transition to ⁵D₀-⁷F_1,2,3,4 transition of Eu³⁺ became weaker as the particle sizes decreased. As the particle sizes became smaller, the ratios of the red emission transition (⁵D₀-⁷F₂) to the orange emission transition (⁵D₀-⁷F₁) (R/O values) first increased by comparing the bulk sample with 96 nm sample, and then decreased by comparing 96 nm sample to 57 nm sample. The quenching concentrations of Ca_10−xEu_x(PO₄)₆(OH)₂ samples increased with decreasing particle size. Possible mechanisms responsible for these phenomena were proposed. Since nanosized Ca_10−xEu_x(PO₄)₆(OH)₂ showed higher fluorescent intensities, higher R/O values and higher quenching concentrations, this material is considered to be a promising phosphor.