径向极化压电陶瓷长圆管复合超声换能器的径向振动

提出了一种圆管式径向复合压电陶瓷换能器,并对其径向振动特性进行了分析。该换能器由径向极化的压电陶瓷圆管以及金属外圆管组成。利用解析法得出了金属圆管以及具有任意壁厚的径向极化压电陶瓷圆管径向振动的机电等效电路。基于金属圆管与压电圆管的机械边界条件,得出了换能器的六端机电等效电路。在此基础上得出了换能器共振及反共振频率方程的解析表达式,给出了换能器的共振及反共振频率与其几何尺寸之间的依赖关系。利用数值方法对换能器的径向振动特性进行了模拟及仿真,并与解析结果进行了比较。最后,设计并加工了一些径向复合管式压电陶瓷换能器,利用精密阻抗分析仪对其共振及反共振频率进行了实验测试。研究结果表明,利用解析理论得出的换能器共振及反共振频率与数值模拟结果以及实验测试结果符合很好。     

一种弯张换能器及其共振频率计算方法

提出一种弯张换能器即欧米伽换能器,推导出其共振频率和位移振形函数。把欧米伽换能器分成四个构成部分,利用旋转薄壳理论和压电理论分别求出各部分的能量并进行相加,得到整个欧米伽换能器能量的泛函表达式;把几何边界连续条件和包含待定系数的位移振形函数代入到欧米伽换能器能量泛函中,运用Rayleigh-Ritz法求出欧米伽换能器的共振频率,再把共振频率代入Rayleigh-Ritz偏微分方程和边界方程中求出位移振形函数的待定系数以获得确定的位移振形函数。该方法也被推广到对钹式换能器共振频率和位移振形函数的求解上。上述求解结果与实验结果和数值软件相结合论证了该方法的有效性。可获得以下结论:(1)欧米伽换能器陶瓷片的径向振动与金属端帽顶部的纵向振动同相,减少了声场中的反相分量,易作为低频换能器使用;(2)为解决欧米伽换能器和钹式换能器的优化设计提供了理论支持;(3)文中求解共振频率和位移振形函数的方法,即可以应用在由旋转薄壳组成的弯张换能器上也可以应用在由旋转薄壳组成的其它结构上,具有普遍性。     

四激励二维正交复合夹心式压电超声换能器的设计

提出了一种四激励二维正交复合夹心式压电超声换能器,换能器由四组纵向极化压电陶瓷晶堆、一个中心耦合金属块和四个外部金属圆锥组成。基于二维耦合振动机理和机电类比原理,建立了换能器的等效电路模型并推导了其谐振频率方程。利用有限元软件仿真分析了四激励正交复合换能器的频响特性和振动特性,并与其单独一个方向振子的振动特性进行了对比。加工了反相和同相模态的换能器,利用阻抗分析仪和激光测振仪测试了其频率响应和二维四向纵振动输出特性,并进行了大功率二维四向超声乳化实验测试。理论、仿真和实验结果表明:换能器具有反相和同相两个纵向正交共振模态,在这两种共振模态下均可实现二维四向纵振动输出,且换能器两个正交方向振子的纵向振动具有相互耦合加强的作用;等效电路法和有限元法所得换能器的共振频率和有效机电耦合系数与实验测试结果吻合,通过与单激励正交复合夹心式压电超声换能器的有效机电耦合系数对比,发现该换能器具有更高的有效机电耦合系数。     

夹心式径向复合压电超声换能器

对夹心式径向复合压电换能器径向振动特性进行了研究。该换能器由弹性内芯、预应力金属管及柱面压电陶瓷晶堆径向复合而成.利用机电类比法,得到了换能器的径向振动等效电路及频率方程。探讨了换能器第1、2阶径向共振频率及有效机电耦合系数与其几何尺寸的关系。研究表明,换能器第1阶径向共振频率随其内芯内径及预应力管壁厚度增大而降低;第2阶共振频率随内芯内径增大存在极小值,但随预应力管壁厚度增大单调下降。此外,采用第2阶径向共振模式能获得较高的有效机电耦合系数,并且压电陶瓷处于位移节线时,换能器有效机电耦合系数达极大值。对换能器共振频率的测试与有限元仿真表明。理论与实验及仿真结果符合较好。     

锥形剖面径向复合超声换能器的机电等效电路

研究了一种锥形剖面径向复合超声换能器。该换能器由一个等截面内金属圆环、一个轴向极化的压电陶瓷圆环和一个锥形剖面外金属圆环沿径向复合而成,且换能器的径向尺寸远大于高度。锥形剖面外金属圆环满足关系式h=h0r,h0为厚度变化常数。基于平面应力径向振动理论,推导了换能器的机电等效电路,得到了共振频率方程和反共振频率方程,进而研究了换能器的振动特性。并将理论计算的第1阶、第2阶径向共振频率和反共振频率与数值仿真结果相比较,二者结果一致。研究表明:锥形剖面换能器第1阶、第2阶径向共振频率、反共振频率、有效机电耦合系数不仅与换能器各部分的材料、径向几何尺寸有关,还与h0有关。h0越大,第1阶径向共振频率、反共振频率越大,有效机电耦合系数先增大后减小。与等截面相比,锥形剖面换能器沿径向向外辐射声波,辐射面积更大,辐射声功率更高,指向性更好。     

压电陶瓷薄圆环振子径向振动的机电等效电路及其分析

本文对轴向极化压电陶瓷薄圆环的径向振动进行了研究，推出了其机电等效电路，得出了振子的共振和反共振频率方程并进行了实验验证。探讨了振子的共振和反共振频率与其材料和几何尺寸之间的依赖关系。     

弯张换能器尺寸与其同相振动谐振频率的关系

本文用有限元计算方法研究了弯张换能器各方向尺寸与其同相振动谐振频率之间的关系，得出以下结论：不一定所有尺寸的换能器都具有理想的同相振动模态；长、宽、高尺寸不变时，若换能器的壳体厚度值增大，则同相振动的谐振频率值随之增大；壳体厚度不变的情况下，减小长，宽、高中的任意一个参数时，其同相振动谐振频率将增高。     

Ⅳ型弯张换能器振动辐射特性分析

本文利用等效电路支路阻抗分析方法,研究了Ⅳ型弯张换能器振动辐射特性与换能器结构之间的关系,得出一系列对换能器设计有用的结论．     

弯张换能器的等效电路支路阻抗分析方法

本文提出了适用于弯张换能器的等效电路支路阻抗分析方法,归纳总结了一些描述IV型弯张换能器振动辐射的特性参量,通过支路阻抗分析方法计算这些特性量可以进行换能器局部结构的优化设计。     

基于传输矩阵法的任意变厚度环型压电超声换能器

变厚度环型径向振动压电超声换能器可以实现阻抗变换、能量集中,具有辐射面积大、全指向性等优点,在功率超声、水声等领域被广泛应用.由于求解复杂变厚度金属圆环径向振动的波动方程比较困难,本文使用传输矩阵法将变厚度金属圆环的径向振动转化为N个等厚度金属圆环径向振动的叠加,得到了任意变厚度金属薄圆环径向振动的等效电路图、共振频率方程和位移放大系数表达式,分析了锥型、幂函数型、指数型、悬链线型金属圆环的位移放大系数与几何尺寸的关系.在此基础上,推导了由任意变厚度金属圆环和等厚度压电圆环复合而成的压电超声换能器径向振动的等效电路和共振频率方程.为了验证理论结果的正确性,使用有限元软件进行仿真,所得一阶、二阶的共振频率和位移放大系数的数值解与理论解符合较好.本研究给出了任意变厚度金属圆环径向振动的普适解,为设计和优化径向压电超声换能器提供了理论指导.     

A new type of high power composite ultrasonic transducer

A new type of high power composite ultrasonic transducer was proposed and studied. The composite transducer consists of a sandwich longitudinal piezoelectric transducer, an isotropic metal hollow cylinder with large radial dimension, and the front and back metal radiation mass. By means of its special structure and Poisson’s effect, the composite transducer can produce vibrations both in its longitudinal and radial directions, and therefore, it can radiate sound waves in three-dimensional space. The electro-mechanical equivalent circuit of the composite transducer was derived and the resonance frequency equation was obtained analytically. Numerical methods were used to simulate the vibration of the composite transducer, and the vibrational displacement distribution, the resonance frequency and the radiation sound field are given. Some composite transducers are designed and manufactured; their resonance frequencies and the radiation acoustic field are measured and compared with the analytical and numerical results. It can be seen that the measured frequencies and acoustic field contour are in good agreement with the analytical and numerical results. It is expected that this kind of composite ultrasonic transducer can be used in more and more power ultrasonic applications, such as ultrasonic cleaning, ultrasonic extraction, ultrasonic sonochemistry and other ultrasonic liquid processing, where high ultrasonic power and large ultrasonic processing space are needed increasingly.     

Cymbal piezoelectric composite underwater acoustic transducer

The working principle of Cymbal piezoelectric composite underwater acoustic transducer was studied in this paper. PZT-5A piezoelectric ceramic disk was used as piezoelectric phase and brass foil was used as end cap electrode of the Cymbal transducer. The silicon rubber was used as the insulated proof layer of the underwater acoustic transducer. The properties of this transducer used as hydrophone, such as operation frequency, free-field voltage receiving sensitivity and directivity, were investigated. Several kinds of prototype of this transducer were fabricated and the properties of this transducer used as hydrophone were tested. The results show that the properties of this transducer used as hydrophone depend on the dimensions of Cymbal transducer because the piezoelectric properties of this transducer are dependent on the dimensions of Cymbal transducer's end caps. The appropriate dimensions for getting higher free-field voltage receiving sensitivity with -184.7 dB were obtained.     

直线自校正式超声步进电机的研究

本文把原有的直线行波电机改制成一种直线式具有自校正功能的超声步进电机,讨论了该电机的驱动理论和步进定位理论,分析了弹性体滑块在驻波钢梁上的受力过程,给出了电机在步进定位阶段滑决所经恢复力的近似解析表达式,并用实验的方法进行了验证,理论计算与实验结果基本符合.     

纵-扭复合模式夹心式功率超声压电换能器的研究

本文对纵-扭复合模式功率超声换能器进行了研究,该换能器由指数型前后金属喇叭盖板以及轴向极化和切向极化的两组压电陶瓷晶片组成。文中推出了换能器中纵向及扭转两种振动模式的共振频率方程。通过改变换能器前后指数型盖板的半径减编系数,得出了换能器中纵向与扭转两种振动模式同频共振的条件。实验表明,换能器的设计频率与测试频率基本一致,而且,换能器的纵向及扭转共振频率也比较接近,该换能器可望应用于超声加工及焊接等高振幅的功率超声技术中。     

Study on the multifrequency Langevin ultrasonic transducer

Langevin ultrasonic transducers are widely used in high-power ultrasonics and underwater sound. In ultrasonic cleaning, a matching metal horn rather than a metal cylinder is used as the radiator in order to enhance the radiating surface and improve the acoustic matching between the transducer and the processed medium. To raise the effect of ultrasonic cleaning, the standing wave in the cleaning tank should be eliminated. One method to eliminate the standing wave in the tank is to use the multifrequency ultrasonic transducer. In this paper, the Langevin ultrasonic horn transducer, with two resonance frequencies, is studied. The transducer consists of two groups of piezoelectric ceramic elements: the back metal cylinder, the middle metal cylinder and the front matching metal horn. The vibrational modes of the transducer are analysed, and resonance frequency equations of the transducer in the half-wave and the all-wave vibrational modes are derived. According to the resonance frequency equations, transducers with two resonance frequencies are designed and made. The resonance frequencies, the effective electromechanical coupling coefficients and the equivalent electric impedances of the transducers are measured. It is shown that the measured resonance frequencies are in good agreement with the computed results, and the transducer can be excited to vibrate at two resonance frequencies, which correspond to the half-wave and the all-wave vibrational modes of the transducer.     

矩形辐射器压电多频超声换能器的研究

研究了一种具有多个共振频率的矩形辐射器夹心式超声换能器,换能器由圆柱形后盖板、压电陶瓷晶堆及矩形六面体辐射器前盖板组合而成。利用表观弹性法和一维近似理论给出了多频换能器横向及纵向理论共振频率方程。对一种特殊情况下的此类换能器进行了有限元及实验分析,给出了各自的频率输入导纳曲线。对理论和实验结果进行分析后表明,此类矩形辐射器夹心式超声换能器可以在不同的振动模态上工作,具有多个共振频率.     

Study of a new type linear ultrasonic motor with double-driving feet

A new type linear USM with double-driving feet has been developed. The stator consists of eight piezoelectric ceramic plates and one brass plate. Piezoelectric ceramics plates are polarized along the thickness and are symmetrically bonded to the two surfaces of one rectangle brass plate. Double-driving feet are assembled on the same side of the brass plate. The working vibration mode is a composite in-plane bimode, which consists of the first longitudinal in-plane vibration mode and the second bending one. The basic size of the linear USM is determined carefully by FEA. The characteristics of the prototype motor were measured experimentally.     

Study on the high power air-coupled ultrasonic compound transducer

The high power air-coupled compound ultrasonic transducer in flexural vibration is studied. The transducer consists of a sandwich longitudinal piezoelectric transducer and a circular thin plate in flexural vibration. The resonance frequency equation and the equivalent circuit of a circular radiator with clamped boundary condition are derived. The resonance frequency equation and the equivalent circuit of the compound transducer are also obtained. The radiated acoustic field of the circular thin plate radiator is analyzed and the directional pattern is calculated. It can be seen that when the vibrational order of the circular thin plate in flexural vibration is increased, the radiated acoustic field becomes complex.     

矩形扭转压电换能器的研制

本文从压电和机械振动等基本理论出发，首次较系统地建立了矩形扭转压电换能器的理论，推导出频率方程，并通过实验进行了验证。     

Study of the sandwiched piezoelectric ultrasonic torsional transducer

The sandwiched piezoelectric ultrasonic torsional transducer was studied. The transducer consists of front and back metal cylinders, and coaxially segmented, tangentially polarized, piezoelectric ceramic tubes. The torsional vibration of the tangentially polarized piezoelectric ceramic slender tube was studied first and its electromechanical equivalent circuit was derived. Based on the network theory and the electromechanical equivalent circuit, the torsional vibration of the piezoelectric ceramic cylinder, formed by stacking a number of identical short piezoelectric ceramic rings, was analysed and the electromechanical equivalent circuit of the piezoelectric ceramic stack in torsional vibration was developed. Finally, the sandwiched ultrasonic torsional transducer was studied and resonance frequency equations were derived which can be used to design and calculate the torsional transducers for different applications.