流变相法合成LiNi0.85Co0.15O2的结构与电化学性能

以一种新型的软化学方法——流变相法, 成功地合成了锂离子电池正极材料LiNi_0.85Co_0.15O₂. 将在600～850 ℃氧气氛下处理6 h后得到的LiNi_1－yCo_yO₂ (y＝0.10, 0.15, 0.20, 0.25), 进行X射线粉末衍射(XRD)与电化学测试. 测试结果表明, 流变相前体经过800 ℃烧结后合成的LiNi_0.85Co_0.15O₂晶胞参数a＝0.2866 nm, c＝1.4193 nm及晶胞体积V＝0.1010 nm³, 以0.1 C倍率在3.0～4.3 V (vs. Li^＋/Li)放电时, 首次放电容量可以达到198.2 mAh/g, 20次循环后, 其放电容量仍在174 mAh/g以上.     

298.15 K Li2B4O7-MgCl2-H2O体系热力学性质的电动势法测定及离子相互作用模型的研究

测定了298.15 K下, 无液接电池Li-ISE│Li₂B₄O₇ (m_A)(aq.), MgCl₂(m_B)(aq.)│AgCl/Ag的电动势, 利用测定结果计算了Li₂B₄O₇-MgCl₂-H₂O体系离子强度在0.05～3 mol•kg^－1范围内, 不同MgCl₂离子强度分数的溶液中LiCl的平均活度系数, 并给出了其随离子强度I, B₄O₇^2－和Mg^2＋浓度的变化规律. 结合以往关于该体系和Li₂B₄O₇-LiCl-H₂O, Li₂B₄O₇-H₂O体系的等压研究结果, 用迭代和多元线性回归方法对Li^＋-Mg^2＋-Cl^－-B₄O₇^2－-H₂O体系的离子相互作用模型进行了研究. 具体方法为考虑了该体系在不同的总硼浓度范围H₃BO₃, B(OH)₄^－, B₃O₃(OH)₄^－和B₄O₅(OH)₄^2－四种含硼化合物的存在以及各硼化合物间的化学平衡, 以修正了的Pitzer渗透系数方程和活度系数方程为基础, 对该体系的等压法和电动势法研究结果进行最小二乘拟合, 拟合的标准偏差为0.0167, 用该模型计算的该体系的渗透系数、活度系数与实验值基本一致.     

核壳结构的Co3O4@δ-MnO2/Pt作为锂氧电池高效催化正极

通过简易、可控的水热方法在泡沫镍基体上直接生长了核壳结构的阵列型Co₃O₄@δ-MnO₂/Pt正极。阵列电极有利于电极的润湿、氧气的传输和Li₂O₂的负载。Co₃O₄@δ-MnO₂/Pt正极对氧还原和氧析出反应具有高的催化性能,可促使Li₂O₂依附Co₃O₄@δ-MnO₂/Pt阵列生长,从而保持阵列结构。该生长行为有利于Li₂O₂在充电时分解。以Co₃O₄@δ-MnO₂/Pt为催化正极的锂氧电池显示出高的容量（在电流密度100 mA·g^-1时容量为2 480 mAh·g^-1）,以及长的循环寿命（容量限定在500 mAh·g^-1时,在200 mA·g^-1电流密度下,可循环65次）,该性能超过了使用Co₃O₄或Co₃O₄@δ-MnO₂催化剂的电池。     

Fe2O3/Al2O3二元气凝胶合成高质量单壁纳米碳管

通过溶胶和超临界干燥方法制得了Fe₂O₃/Al₂O₃二元气凝胶，其比表面积和孔隙体积分别为246 m²·g^-1和1.89 cm³·g^-1，并具有较宽的孔径分布。以Fe₂O₃/Al₂O₃二元气凝胶作催化剂，通过甲烷催化裂解成功地合成了高质量的单壁纳米碳管。利用FESEM、TEM和HRTEM、Raman光谱等分析手段研究了反应温度对单壁纳米碳管生长的影响。结果表明在900 ℃时合成单壁纳米碳管的质量较高，并且合成的炭产物为毡状，该炭产物主要为高质量的单壁纳米碳管。     

Eu3+掺杂SiO2-B2O3-NaF玻璃的制备及发光性质

The Eu-doped SiO₂-B₂O₃-NaF glass was prepared by sol-gel process, using tetraethoxy Silicane, boric acid and sodium fluoride as starting materials, 0.10 mol·L^-1 EuCl₃ solution as the dopant. The luminescent properties of Eu³⁺ doped SiO₂-B₂O₃-NaF phosphors were investigated. The phosphors showed prominent luminescence in pink, the strong emission of Eu³⁺ comes from electronic transition of ⁵D₀- ⁷F₁（591 nm）and ⁵D₀- ⁷F₂（615 nm）,which derived from two transition modes of magnetic-dipole and electric-dipole .The peak intensity of 591nm in SiO₂-B₂O₃-NaF matrix is much stronger than it in the other matrixes, it means that SiO₂-B₂O₃-NaF has sensitization on the transition of ⁵D₀- ⁷F₁ (Eu³⁺). If there are broad bonds in the range of 275～380 nm in the excitation spectrum of Eu³⁺ -doped SiO₂-B₂O₃-NaF glass, the emission peak intensity should be intensified. It is because the electron migration CT band of O^2--Eu³⁺. For all Eu³⁺ concentrations used, the investigation found that when the mass of fraction got to 29.19×10^-3, the luminescence intensity reached the summit. And there is a phenomenon of concentration quenching. Investigation with the same concentration of Eu³⁺ at different annealed temperature, we found that the sample annealed at 400 ℃, the luminescence intensity achieved its maximum value, and Eu³⁺ in this matrix had a phenomenon of temperature quenching. The structural characterization of these luminescent materials was carried by used XRD and TEM. The result showed that the phosphor was in amorphous phase.     

层状Li(Ni1/3Co1/3Mn1/3)O2正极材料的合成与电化学性能研究

采用共沉淀-喷雾造粒法制备前驱体, 于750 ℃在空气中煅烧20 h合成出层状Li(Ni_1/3Co_1/3Mn_1/3)O₂正极材料, 并用XRD, SEM, 粒度分析和电性能测试考察了所得材料结构、形貌及电化学性能. 本层状Li(Ni_1/3Co_1/3Mn_1/3)O₂正极材料具有α-NaFeO₂结构, 六方晶系, R3m空间群, 其晶胞参数为a＝0.2865 nm, c＝1.4238 nm. 当材料分别在2.8～4.2, 2.8～4.5 V间进行充放电时, 其首次放电容量分别为173.5和185.4 mAh•g^－1, 首次充放电效率分别为90%和83.8%, 40次循环后容量保持率分别为96%和84%.     

Criegee自由基CH2O2与H2O反应机理及动力学的理论研究

在6-311＋G(2d,2p)水平下, 采用密度泛函理论(DFT)的B3LYP方法, 研究了Criegee 自由基CH₂O₂与H₂O的反应. 结果表明反应存在三个通道: CH₂O₂＋H₂O®HOCH₂OOH (R1); CH₂O₂＋H₂O®HCO＋OH＋H₂O (R2); CH₂O₂＋H₂O®HCHO＋H₂O₂ (R3), 各通道的势垒高度分别为43.35, 85.30和125.85 kJ/mol. 298 K下主反应通道(R1)的经典过渡态理论(TST)与变分过渡态理论(CVT)的速率常数k^TST与k^CVT均为2.47×10^－17 cm³•molecule^－1•s^－1, 而经小曲率隧道效应模型(SCT)校正后的速率常数k^CVT/SCT为 5.22×10^－17 cm³•molecule^－1•s^－1. 另外, 还给出了200～2000 K 温度范围内拟合得到的速率常数随温度变化的三参数Arrhenius方程.     

面向异丁烷脱氢介孔γ-Al2O3基催化剂的合成及其高催化性能

采用溶剂蒸发自组装法调控载体形貌及孔道结构,成功制备了有序介孔氧化铝载体。以铬氧物种为活性组分,碱金属钾为助剂,采用浸渍法制备负载型催化剂,用于异丁烷催化脱氢反应,研究了反应温度、原料流速、催化剂粒径等因素对催化性能的影响。采用X射线粉末衍射、透射电子显微镜、N₂物理吸附、氢气程序升温还原及热重等表征方法探讨了载体形貌、孔道结构与催化性能的构效关系,结果表明,低温下有利于控制异丙醇铝的水解和缩合及介孔γ-Al₂O₃的研制。与常规的γ-Al₂O₃相比,所制备的介孔γ-Al₂O₃的有更大的比表面积和良好的有序性,在600℃、101.325kPa、GHSV=1 000 h^-1的条件下,10%（w/w）Cr₂O₃/γ-Al₂O₃催化剂性能最佳,异丁烷的转化率达63.1%,异丁烯的选择性达到85.5%。与传统的催化剂相比,介孔Cr₂O₃/γ-Al₂O₃催化剂具有大的比表面积,高度分散的活性组分,优良的催化性能和良好的抗积碳能力。     

纳米固体超强酸SO42-/Fe2O3的制备及其催化合成乙酸乙酯

将Fe₂O₃纳米粉体经一定浓度的H₂SO₄浸泡活化后制成纳米固体超强酸SO₄^2-/Fe₂O₃,将其用于催化合成乙酸乙酯以考察其活性。利用均匀设计分析了超强酸制备过程及酯化反应过程中各因素的影响,研究结果表明较好的制备条件是:H₂SO₄浓度:2.5mol·L^-1;浸泡时间:1h;活化温度:167℃;活化时间:1h,此时获得的固体超强酸SO₄^2-/Fe₂O₃的粒径小于50nm。当催化剂用量为冰乙酸质量的5%,n(乙醇)∶n(冰乙酸)为3∶1,反应3.5h后乙酸的转化率高于80%。该催化剂经H₂SO₄溶液浸泡、活化再生后可重新使用,推断出其酸强度H₀<-14.5。     

Cr2O3和CrO3/Cr2O3催化剂的2-氯-1,1,1-三氟乙烷气相氟化反应的活性物种和失活

采用沉淀法和浸渍法制备了2种铬基（Cr₂O₃和CrO₃/Cr₂O₃）催化剂,用于气相氟化2-氯-1,1,1-三氟乙烷合成1,1,1,2-四氟乙烷。研究发现含有低价铬（Cr³⁺）物种的Cr₂O₃催化剂上2-氯-1,1,1-三氟乙烷的稳态转化率为18.5%,而含有高价铬（Cr⁶⁺）物种和低价铬（Cr³⁺）物种的CrO₃/Cr₂O₃催化剂初始转化率达到30.6%,然而存在明显的失活。含有Cr⁶⁺物种的CrO₃/Cr₂O₃催化剂的2-氯-1,1,1-三氟乙烷氟化反应初始TOF值为1.71×10^-4 mol_HCFC-133a·mol_Cr（Ⅵ）^-1·s^-1,高于含有Cr³⁺物种的Cr₂O₃催化剂（4.16×10^-5 mol_HCFC-133a·mol_Cr（Ⅲ）^-1·s^-1）。Cr₂O₃催化剂在氟化反应前后催化剂的物相结构保持不变;而含有高价铬物种的CrO₃/Cr₂O₃催化剂经HF反应后生成了CrO_xF_y活性物种。然而,CrO_xF_y物种在反应中挥发或转化成稳定但无活性的CrF₃,从而导致催化剂失活。     

基于纳米ZnO-ZrO2催化发光丙酮传感器的研究

研究了丙酮在纳米ZnO-ZrO2(质量比为4:1)表面催化发光行为,发现基于这种纳米催化剂的气体传感器对丙酮的检测具有高灵敏度和较强的选择性。在波长460 nm,温度219℃,载气流速25 mL/min时进行定量分析,催化发光强度与丙酮浓度在一定范围内呈良好的线性关系,线性范围为0.1～4000 mL/m3(r=0.9996,n=6);检出限为1.6 mL/m3(S/N=3)。传感器工作时间可达106h以上,可用于丙酮的实时在线检测。     

Nanosized SrCO3-based chemiluminescence sensor for ethanol

The development of a nanosized SrCO₃-based sensor based on the generated chemiluminescence (CL) from catalytic oxidation of organic vapors was demonstrated. The luminescence characteristics and effect of different parameters, such as temperature and flow rate, were discussed with a prepared CL detection system. This sensor was evaluated for the measurement of gaseous ethanol as a model analyte. Under the optimized conditions, the linear range of CL intensity versus concentration of ethanol vapor is 6-3750 ppm (r=0.998, n=8), with the limit of detection of 2.1 ppm. This SrCO₃ sensor shows high selectivity to ethanol. There is no response while the foreign substances, such as gasoline, ammonia and hydrogen, are passing through the sensor. The hydrocarbons can slightly interfere with the ethanol measurement. The sensor also exhibits good stability and durability during 100 h reaction with 2000 ppm ethanol. The interactions between ethanol molecules and SrCO₃ involving CL emission were investigated by utilizing gas chromatography in this paper and the possible mechanism of CL from ethanol oxidation on SrCO₃ was discussed.     

A cataluminescence gas sensor based on nanosized V2O5 for tert-butyl mercaptan

This work proposed a gas sensor for the determination of tert-butyl mercaptan, one of the highly toxic volatile sulfur compounds, which was based on cataluminescence emission during its catalytic oxidation on the surface of nanosized V₂O₅. The cataluminescence characteristics and the optimum conditions, including the morphology of sensing material, the wavelength of cataluminescence emission, the oxygen flow rate and working temperature were investigated in detail. Under the optimized conditions, the calibration curve of the relative cataluminescence intensity versus the concentration of tert-butyl mercaptan vapor was made, with the linear range of 5.6-196 μg mL⁻¹ and the detection limit of 0.5 μg mL⁻¹ (S/N = 3). The relative standard deviation (R.S.D.) (n = 5) of relative cataluminescence intensity for 84 μg mL⁻¹ tert-butyl mercaptan was 3.6%. There is no or weak response to some common substances, such as formic acid, alcohol (methanol, ethanol, propanol, isopropanol, n-butanol, isoamyl alcohol), o-dichlorobenzene, acetonitrile, ethyl acetate, aldehyde (formaldehyde, acetaldehyde and propanal), 1,2-dichloroethane and ammonia. Furthermore, the proposed sensor was successfully used for determining tert-butyl mercaptan in four artificial samples, with a good recovery. The results demonstrated that the proposed gas sensor had a promising capability for the tert-butyl mercaptan in routine monitoring.     

H2O2-鲁米诺-荧光素钠-K2CO3高灵敏化学发光法测定二氧化碳

在碱性介质中, CO₃^2－对H₂O₂氧化鲁米诺化学发光反应具有重要作用, 荧光素钠对该反应具有很强的增敏作用. 据此, 建立了化学发光法测定二氧化碳的新方法. 方法的线性范围为1.0×10^－10～5.0×10^－6 mol•L^－1 CO₃^2－, 检出限为 1.2×10^－11 mol•L^－1 CO₃^2－ (相当于5.3×10^－10 g•L^－1 CO₂). 该方法用于室内外空气中二氧化碳含量的测定, 相对标准偏差1.8%～2.1% (n＝11), 加标实验回收率97.6%～101.4%. 论文还探讨了反应的发光机理, 发光反应很可能是由溶液中的CO₃^2－与H₂O₂作用而产生的活性自由基引发, 荧光素钠对发光的增敏作用为化学能量转移过程.     

A novel gaseous pinacolyl alcohol sensor utilizing cataluminescence on alumina nanowires prepared by supercritical fluid drying

A cataluminescence (CTL) sensor using Al₂O₃ nanowires as the sensing material was developed for the determination of trace pinacolyl alcohol in air samples based on the catalytic chemiluminescence (CL) of pinacolyl alcohol on Al₂O₃ nanowires. Eight catalysts were examined and the CL intensity on Al₂O₃ nanowires prepared by supercritical fluid drying was the strongest. This novel CL sensor showed high sensitivity and selectivity to gaseous pinacolyl alcohol at optimal temperature of 340 °C. Quantitative analysis was performed at a wavelength of 460 nm. The linear range of CTL intensity versus concentration of gaseous pinacolyl alcohol was 0.09 × 10⁻⁶ to 2.56 × 10⁻⁶ g mL⁻¹ (r = 0.9983, n = 6) with a detection limit (3σ) of 0.0053 × 10⁻⁶ g mL⁻¹. None or only very low levels of interference were observed while the foreign substances such as water vapor, ethanol, ammonia, chloroform, benzene, nitrogen dioxide, methylbenzene, hydrochloric acid, methanol and butanol were passing through the sensor. The response time of the sensor is less than 100 s, and the sensor had a long lifetime more than 60 h. The sensor would be potentially applied to analysis of the nerve agents such as Soman.     

Highly Responsive and Selective Ethanol Gas Sensor Based on Co3O4-Modified SnO2 Nanofibers

SnO₂ nanofibers were synthesized by electrospinning and modified with Co₃O₄ via impregnation in this work. Chemical composition and morphology of the nanofibers were systematically characterized, and their gas sensing properties were investigated. Results showed that Co₃O₄ modification significantly enhanced the sensing performance of SnO₂ nanofibers to ethanol gas. For a sample with 1.2 mol% Co₃O₄, the response to 100 ppm ethanol was 38.0 at 300℃, about 6.7 times larger than that of SnO₂ nanofibers. In addition, the response/recovery time was also greatly reduced. A power-law dependence of the sensor response on the ethanol concentration as well as excellent ethanol selectivity was observed for the Co₃O₄/SnO₂ sensor. The enhanced ethanol sensing performance may be attributed to the formation of p-n heterojunctions between the two oxides.     

TPR studies on steam reforming of 2-propanol on Rh/Al2O3, Ru/Al2O3 and Pd/Al2O3

Reaction pathways for steam reforming of 2-propanol (isopropyl alcohol, IPA) on Rh/Al₂O₃, Ru/Al₂O₃ and Pd/Al₂O₃ have been studied by temperature-programmed reactions (TPRs) of IPA and acetone in the presence of steam. The results of TPRs suggest that that of IPA on Rh/Al₂O₃ and Ru/Al₂O₃ proceeds via acetone, while the steam reforming of IPA on Pd/Al₂O₃ takes place via propene from acetone. This revised version was published online in August 2006 with corrections to the Cover Date.     

Detection of acetone in the human breath as diabetes biomarker based on PPy/WO3 nanocomposite sensor by FFT continuous cyclic voltammetry method

This research represents a novel detection method of acetone level in the exhaled breath samples (RH=88 %) based on polypyrrole/tungsten oxide (PPy/WO₃) nanocomposite sensor. The PPy/WO₃ sensor was fabricated by the deposition of nanocomposite on/between interdigitated electrodes (IDEs) through electrospray coating and was then characterized by FE-SEM imaging. In this detection method, the coulometric signal of the sensor was calculated using Fast Fourier Continuous Cyclic Voltammetry (FFTCCV), where cyclic voltammetry (CV) was applied to the sensor in the defined potential rang and then charge changes of the sensor was obtained by integration of the current in all scanned potential ranges. FFTCCV method enhances the sensitivity of the sensor when exposed to the gas mixtures containing acetone. In addition to its fast coulometric response time (≤5 s) in the two linear ranges of 0.7–2.8 ppm and 2.8–28.2 ppm (R²=0.99), FFTCCV method provides the low detection limit of 70 ppb, and high sensitivity toward acetone at the optimum values of the parameters. The fabricated sensor showed great selectivity toward acetone when exposed to humid air and some exhaled gas like carbon dioxide, ammonia, methanol, ethanol and alkyl amines. The results were very satisfying as the sensor was capable to detect different acetone levels in human exhaled breath as non-invasive diagnosis of diabetes with a good correlation (R²≃0.9) to the routine blood sugar test taken by different commercial glucometers results.     

纳米复合氧化物催化发光法测定空气中的甲醛

基于纳米复合氧化物上甲醛被催化氧化产生化学发光的现象, 建立了直接测定空气中微量甲醛的方法. 实验发现, 甲醛在许多纳米级金属氧化物表面都有发光现象, 但在纳米级钼钒钛(原子比为2∶3∶5)复合氧化物表面上有较高的发光强度和较好的选择性. 最佳实验条件为: 分析波长535 nm, 测定温度265 ℃, 载气流速150 mL/min. 方法的检测限(3σ)为0.04 mg/m³, 线性范围为0.07～34 mg/m³, 相关系数为0.9994, 回收率为98.2%～101.4%. 对常见共存物的研究发现, 除丙酮外, 苯、氨、二氧化硫和乙醇不干扰测定.     

Structures, vibrational frequencies, and electron affinities of SF5On/SF5On (n = 1–3)

The molecular structures, vibrational frequencies, and electron affinities of the SF₅O_n/SF₅O_n⁻ (n = 1–3) species have been examined with four hybrid density functional theory (DFT) methods. The basis set used in this work is of double-ζ plus polarization quality with additional diffuse s- and p-type functions, denoted DZP++. The geometries are fully optimized with each DFT method independently. The SF₅O_n (n = 1–3) species should be potential greenhouse gases. The anion SF₅O₂⁻ with C_s symmetry has a ³A″ electronic state, and the neutral SF₅O₃ with ²A″ electronic state has C_s symmetry. The anions SF₅O₂⁻ and SF₅O₃⁻ should be regarded as SF₅⁻·O₂ and SF₅O⁻·O₂ complexes, respectively. Three different types of the neutral–anion energy separation presented in this work are the adiabatic electron affinity (EA_ad), the vertical electron affinity (EA_vert), and the vertical detachment energy (VDE). The EA_ad values predicted by the B3PW91 method are 5.22 (SF₅O), 4.38 (SF₅O₂), and 3.61 eV (SF₅O₃). Compared with the experimental vibrational frequencies, the BHLYP method overestimates the frequencies, and the other three methods underestimate the frequencies. The bond dissociation energies D_e (SF₅O_n → SF₅O_n−m + O_m) for the neutrals SF₅O_n and D_e (SF₅O_n⁻ → SF₅O_n−m⁻ + O_m and SF₅O_n⁻ → SF₅O_n−m + O_m⁻) for the anions SF₅O_n⁻ are reported.