Effect of gate length on breakdown voltage in AlGaN/GaN high-electron-mobility transistor

The effects of gate length L_G on breakdown voltage VBRare investigated in AlGaN/GaN high-electron-mobility transistors(HEMTs) with L_G= 1 μm~20 μm. With the increase of L_G, VBRis first increased, and then saturated at LG= 3 μm. For the HEMT with L_G= 1 μm, breakdown voltage VBRis 117 V, and it can be enhanced to 148 V for the HEMT with L-_G= 3 μm. The gate length of 3 μm can alleviate the buffer-leakage-induced impact ionization compared with the gate length of 1 μm, and the suppression of the impact ionization is the reason for improving the breakdown voltage.A similar suppression of the impact ionization exists in the HEMTs with LG 3 μm. As a result, there is no obvious difference in breakdown voltage among the HEMTs with LG= 3 μm~20 μm, and their breakdown voltages are in a range of 140 V–156 V.     

Direct probing of Schottky barriers in Si nanowire Schottky barrier field effect transistors

This work elucidates the role of the Schottky junction in the electronic transport of nanometer-scale transistors. In the example of Schottky barrier silicon nanowire field effect transistors, an electrical scanning probe technique is applied to examine the charge transport effects of a nanometer-scale local top gate during operation. The results prove experimentally that Schottky barriers control the charge carrier transport in these devices. In addition, a proof of concept for a reprogrammable nonvolatile memory device based on band bending at the Schottky barriers will be shown.     

Tunable quantum dot resonator embedded in a quantum wire

Combined quantum wire and quantum dot system is theoretically predicted to show unique conductance properties associated with Coulomb interactions. We use a split gate technique to fabricate a quantum wire containing a quantum dot with two tunable potential barriers in a two-dimensional electron gas. We observe the effects of the quantum dot cavity on the electron transport through the quantum wire, such as Coulomb oscillations near the pinch-off voltage and periodic conductance oscillations on the first conductance plateau.     

65 nm互补金属氧化物半导体场效应和晶体管总剂量效应及损伤机制

对65 nm互补金属氧化物半导体工艺下不同尺寸的N型和P型金属氧化物半导体场效应晶体管(NMOSFET和PMOSFET)开展了不同偏置条件下电离总剂量辐照实验.结果表明:PMOSFET的电离辐射响应与器件结构和偏置条件均有很强的依赖性,而NMOSFET表现出较强的抗总剂量性能;在累积相同总剂量时,PMOSFET的辐照损伤远大于NMOSFET.结合理论分析和数值模拟给出了PMOSFET的辐射敏感位置及辐射损伤的物理机制.     

Fabrication of BDD quantum node switches on embedded GaAs quantum wires grown by selective MBE

In view of applications to hexagonal binary decision diagram (BDD) LSIs, a first attempt is made to form quantum BDD node switches on selectively grown (SG) embedded quantum wires (QWRs) by molecular beam epitaxy (MBE). SG branch switches controlled by a Schottky wrap gate (WPG) were successfully fabricated by MBE growth and subsequent device processing. Gate control characteristics were studied by gate-dependent Shubnikov–de-Haas measurements, and the behavior was found to be similar to that of devices fabricated on wires by etching. The switch exhibited clear conductance quantization at low temperature, and temperature dependence of the voltage slope of conductance jump was clarified. A Y-branch BDD node device using two SG branch switches was successfully fabricated, and realized clear path switching characteristics.     

反向衬底偏压下纳米N沟道金属氧化物半导体场效应晶体管中栅调制界面产生电流特性研究

研究了反向衬底偏压V_B下纳米N沟道金属氧化物半导体场效应晶体管中栅调制界面产生(GMG)电流I_GMG特性, 发现I_GMG曲线的上升沿与下降沿随着|V_B|的增大向右漂移. 基于实验和理论模型分析, 得出了V_B与这种漂移之间的物理作用机制, 漂移现象的产生归因于衬底偏压V_B 调节了表面电势φ_s在栅电压V_G 中的占有比重: |V_B|增大时相同V_G下φ_s会变小, φ_s 的变化继而引发上升沿产生率因子g_r减小以及下降沿产生率因子g_f增大. 进一步发现I_GMG 上升沿与下降沿的最大跨导G_MR, G_MF 在对数坐标系下与V_B成线性关系, 并且随着|V_B|增加而增大. 由于漏电压V_D在I_GMG 上升沿与下降沿中的作用不同, 三种V_D下G_MR-V_B曲线重合而G_MF-V_B曲线则产生差异. 增大V_D 会增强g_f 随V_G的变化, 因此使得给定V_B 下的G_MF变大. 同时这却导致了更大V_D下G_MF-V_B 曲线变化的趋势减缓, 随着V_D从0.2 V变为0.6 V, 曲线的斜率s从0.09减小到0.03. 关键词： 产生电流 表面势 衬底偏压 N沟道金属氧化物半导体场效应晶体管     

Low frequency impedance of a round superconducting wire

We calculated the electric field E on the surface of a straight superconducting wire with circular cross-section carrying AC transport current I=I_acosωt. Performing the Fourier analysis of E, we found that both components of the first harmonic have the same form: the critical current I_c in prefactor and the rest depending on the ratio F=I_a/I_c. The in-phase component leads to the classical result of loss calculation, while the out-of-phase component was derived for the first time. Thus the wire can be symbolized by a complex self-inductance L₁(I)=L₁′(I)−jL₁″(I) where L₁′ represents the reactive power while L₁″ the losses. When the lock-in amplifier, used to sort out the components of the first harmonic, is utilized in the wide-band mode, it allows one to determine the magnetic flux penetrated in the wire volume at two significant moments of the AC cycle: at zero current (remanent flux) and at the amplitude value of current.     

声表面波单电子输运器件中量子线的电学特性研究

通过在Al_xGa_1-xAs/GaAs异质结表面制作一对分裂门,获得了用于实现声表面波单电子输运的准一维量子线.实验研究了0.3K时电子沿该量子线的输运性质.通过自洽求解二维薛定谔方程和泊松方程,分析了该量子线的导带能量和电子浓度的分布,并讨论了量子线宽度对分裂门方向形成限制势的影响.特别是对其线性电子浓度随温度及分裂门电压的变化关系进行了数值模拟,所得到的钳断电压与实验测量值符合较好. 关键词： 量子线 分裂门 线性电子浓度 钳断电压     

Neutrino astronomy and massive long-lived particles from the big bang

We consider the neutrino flux from the decay of long-lived big-bang particles. The red-shift z_tr at which the neutrino transparency of the universe sets in is calculated as a function of neutrino energy: z_tr 1 × 10⁵ for TeV neutrinos and z_tr 3 × 10⁶ for 10 MeV neutrinos. One might expect the production of detectable neutrino flux at z z_tr, but, as demonstrated in this paper, the various upper limits, most notably due to nucleosynthesis and diffuse X- and gamma-rays, preclude this possibility. Unless the particle decay is strongly dominated by the pure neutrino channel, observable neutrino flux can be produced only at the current epoch, corresponding to red-shift z ≈ 0. For the thermal relics which annihilate through the gauge bosons of SU(3)×SU(2)×U(1) group, the neutrino flux can be marginally detectable at 0.1 < E_v < 10 TeV. As an example of non-thermal relics we consider gravitinos. If gravitinos are the lightest supersymmetric particles (LSP) they can produce the detectable neutrino flux in the form of a neutrino line with energy , where M_G is the gravitino mass. The flux strongly depends on the mechanisms of R-parity violation. It is shown that heavy gravitinos (M_G 100 GeV) can make up the dark matter in the universe.     

Towards a chemically driven molecular electron pump

Charge can be pumped through a tiny gated portal from a reservoir at low electrochemical potential to one at the same or higher electrochemical potential by cyclically modulating the portal and gate energies. A theoretically and experimentally well established mechanism is Thouless adiabatic pumping, achieved by a precisely timed out-of-phase modulation of at least two parameters of the system. Here we show that stochastic modulation between two configurations of gate and portal energies can drive efficient pumping by a different, nonadiabatic, mechanism that may provide a basis for chemically driven electron pumping through a molecular wire.     

Optimum coupling of a Gaussian beam to a corner reflector with a four-wavelength antenna

The coupling of a Gaussian radiation beam to a corner reflector with a four-wavelength long wire antenna was studied theoretically and experimentally. The antenna configuration in conjunction with a Schottky barrier diode is recently used widely as a fast submillimeter wave detector. The optimum angle focusing the radiation to the antenna has been obtained and is 11° (half-width at the 8.7dB points).     

Enhancement of fMAX of InP-based HEMTs by double-recessed offset gate process

A double-recessed offset gate process technology for InP-based high electron mobility transistors (HEMTs) has been developed in this paper. Single-recessed and double-recessed HEMTs with different gate offsets have been fabricated and characterized. Compared with single-recessed devices, the maximum drain-source current (I_D,max) and maximum extrinsic transconductance (g_m,max) of double-recessed devices decreased due to the increase in series resistances. However, in terms of RF performance, double-recessed HEMTs achieved higher maximum oscillation frequency (f_MAX) by reducing drain output conductance (g_ds) and drain to gate capacitance (C_gd). In addition, further improvement of f_MAX was observed by adjusting the gate offset of double-recessed devices. This can be explained by suppressing the ratio of C_gd to source to gate capacitance (C_gs) by extending drain-side recess length (L_rd). Compared with the single-recessed HEMTs, the f_MAX of double-recessed offset gate HEMTs was increased by about 20%.     

基于原位等离子体氮化及低压化学气相沉积-Si_3N_4栅介质的高性能AlGaN/GaN MIS-HEMTs器件的研究

通过对低压化学气相沉积(LPCVD)系统进行改造,实现在沉积Si_3N_4薄膜前的原位等离子体氮化处理,氮等离子体可以有效地降低器件界面处的氧含量和悬挂键,从而获得了较低的LPCVD-Si_3N_4/GaN界面态,通过这种技术制作的MIS-HEMTs器件,在扫描栅压范围V_(G-sweep)=(-30 V,+24 V)时,阈值回滞为186 mV,据我们所知为目前高扫描栅压V_(G+)(20 V)下的最好结果.动态测试表明,在400 V关态应力下,器件的导通电阻仅仅上升1.36倍(关态到开态的时间间隔为100μs).     

基于有限元方法的有机场效应晶体管特性模拟与实验验证

采用有限元方法,借助多物理场软件COMSOL模拟了底栅顶接触结构有机场效应晶体管电位和载流子浓度随源漏电压Vds的变化。模拟结果表明,当固定栅压V_g=-10 V时,改变V_(ds)从0~-10 V,对于电位分布,从栅极到源漏电极竖直方向有渐进的变化,而从源极到漏极的水平方向呈现由大到小明显的梯度变化。对于载流子浓度,观察到沟道处从源极向漏极逐渐减少,在靠近漏极的区域减少得尤为明显,而当源漏电压等于栅极电压时,产生夹断现象。进一步将模拟结果与实际制备的器件性能进行了对比,模拟结果与实验数据所显示的分布趋势大体相同,印证了模拟的合理性。由此表明,采用模拟方法分析有机场效应晶体管的器件特性,对于实际制备器件具有重要的指导意义。     

III–V quantum devices and circuits based on nanoscale Schottky gate control of hexagonal quantum wire networks

The concept, the present status, key issues and future prospects of a novel hexagonal binary decision diagram (BDD) quantum circuit approach for III–V quantum large-scale integrated circuits (QLSIs) are presented and discussed. In this approach, the BDD logic circuits are implemented on III–V semiconductor-based hexagonal nanowire networks controlled by nanoscale Schottky gates. The hexagonal BDD QLSIs can operate at delay-power products near the quantum limit in the quantum regime as well as in the many-electron classical regime. To demonstrate the feasibility of the present approach, GaAs Schottky wrap gate (WPG)-based single-electron BDD node devices and their integrated circuits were fabricated and their proper operations were confirmed. Selectively grown InGaAs sub-10 nm quantum wires and their hexagonal networks have been investigated to form high-density hexagonal BDD QLSIs operating in the quantum regime at room temperature.     

Mo,Ta, W在NixAl1-x(x=0.25,0.5,0.75) 中的择优占位

用多体势结合分子动力学计算了L1₂型NiAl₃, L1₂型Ni₃Al, L1₀型NiAl和B₂ 型NiAl的晶格常数, 结合能以及合金形成热; 分析了结构性点缺陷在上述四种合金中的存在形式; 在此基础上研究了合金化元素Mo, Ta, W在Ni_xAl_1-x(x=0.25,0.5,0.75)中的择优占位行为. 计算结果表明: 对于四种结构的Ni-Al合金, 偏离理想化学配比时,主要的结构缺陷形式是反位置; 根据占位能最小化, 第三组元元素Mo, Ta, W在上述四种Ni-Al中都显著优先占据Al格位. 关键词： 多体势 Ni-Al合金 占位     

Magnetopolaron in a Rectangular Harmonic Quantum Wire

Cyclotron resonance of a magnetopolaron in a rectangular harmonic quantum wire withmagnetic fidd normal to the quanturn wire is investigated theoretically. The results weobtained show that, the Landau levels in the quantum wire are raised relative to those intwo-dimensional quanturn well due to the addition of a parabolic potential. The results alsoshow that, the cyclotron frequency and cyclotron mass of ID polaron are very different fromthose of 2D polaron, especially for weak magnetic field region ω_C << ω_LO     

Observation of the Kondo effect in a spin-3/2 hole quantum dot

We report the observation of Kondo physics in a spin-3/2 hole quantum dot. The dot is formed close to pinch-off in a hole quantum wire defined in an undoped AlGaAs/GaAs heterostructure. We clearly observe two distinctive hallmarks of quantum dot Kondo physics. First, the Zeeman spin splitting of the zero-bias peak in the differential conductance is independent of the gate voltage. Second, this splitting is twice as large as the splitting for the lowest one-dimensional subband. We show that the Zeeman splitting of the zero-bias peak is highly anisotropic and attribute this to the strong spin-orbit interaction for holes in GaAs.     

Electron transport in gated InGaAs and InAsP quantum well wires in selectively grown InP ridge structures

The purpose of this work is to fabricate ribbon-like InGaAs and InAsP wires embedded in InP ridge structures and investigate their transport properties. The InP ridge structures that contain the wires are selectively grown by chemical beam epitaxy (CBE) on pre-patterned InP substrates. To optimize the growth and micro-fabrication processes for electronic transport, we explore the Ohmic contact resistance, the electron density, and the mobility as a function of the wire width using standard transport and Shubnikov–de Haas measurements. At low temperatures the ridge structures reveal reproducible mesoscopic conductance fluctuations. We also fabricate ridge structures with submicron gate electrodes that exhibit non-leaky gating and good pinch-off characteristics acceptable for device operation. Using such wrap gate electrodes, we demonstrate that the wires can be split to form quantum dots evidenced by Coulomb blockade oscillations in transport measurements.     

Direct growth of graphene films without catalyst on flexible glass substrates by PECVD

A hydrogen-plasma-etching-based plasma-enhanced chemical vapor deposition(PECVD) synthesis route without metal catalyst for preparing the graphene films on flexible glass is developed. The quality of the prepared graphene films is evaluated by scanning electron microscopy, x-ray photoelectron spectroscopy, high-resolution transmission electron microscopy, ultraviolet-visible spectroscopy, and electrochemical measurements. In a radio frequency(RF) power range of50 W–300 W, the graphene growth rate increases with RF power increasing, while the intensity ratio of D-to G-Raman peak(ID/IG) decreases. When the RF power is higher than 300 W, the ID/IGrises again. By optimizing experimental parameters of hydrogen plasma etching and RF power, the properties of as-prepared flexible graphene on glass are modulated to be able to achieve the graphene's transparency, good electrical conductivity, and better macroscopic uniformity.Direct growth of graphene film without any metal catalyst on flexible glass can be a promising candidate for applications in flexible transparent optoelectronics.