Preparation of Co–Al and Ni–Al layered double hydroxide thin films by a sol–gel process with hot water treatment

Using hot water treatment of sol–gel derived precursor gel films, Co–Al and Ni–Al layered double hydroxide (LDH) thin films were prepared. The precursor gel films of Al₂O₃–CoO or Al₂O₃–NiO were prepared from cobalt or nickel nitrates and aluminum tri-sec-butoxide using the sol–gel method. Then, the precursor gel films were immersed in a NaOH aqueous solution of 100 °C. Nanocrystallites of Co–Al and Ni–Al LDH were precipitated with the hot water treatment with NaOH solution. The largest amounts of nanocrystals were obtained with a solution of pH = 10 for Co–Al LDH, and with that of pH = 9 for Ni–Al LDH. X-ray diffraction measurements confirmed that this process formed CO₃ ²⁻ intercalated LDHs. Both Co–Al and Ni–Al LDH thin films were confirmed to work as electrodes for electrochemical devices by cyclic voltammogram measurements.     

On the sol–gel preparation of different tungstates and molybdates

The preparation and characterization of the M′–M′′–O nitrate–tartrate (M′ = Ca, Ba, Gd and M′ = W, Mo) precursor gels synthesized by simple, inexpensive, and environmentally benign aqueous sol–gel method is reported. The obtained gels were studied by thermal (TG/DSC) analysis. TG/DSC measurements revealed the possible decomposition pathway of synthesized M′–M′′–O nitrate–tartrate gels. For the synthesis of different metal tungstates and molybdates, the precursor gels were calcined at different temperatures (650, 800, and 900 °C). According to the X-ray diffraction (XRD) analysis data, the crystalline compounds CaMo_1-x W _x O₄ doped with Ce³⁺ ions, BaMo_1-x W _x O₄ doped with Eu³⁺ ions and Gd₂Mo₃O₁₂ were obtained from nitrate–tartrate gels annealed at 650–900 °C temperatures. The XRD data confirmed that the fully crystalline single-phase powellite, scheelite, or Gd₂(MoO₄)₃ structures were formed already at 650 °C. Therefore, the suggested sol–gel method based on the complexation of metal ions with tartaric acid is suitable for the preparation of mixed tungstates–molybdates at relatively low temperature in comparison with solid-state synthesis.     

Study on synthesis and evolution of sodium potassium niobate ceramic powders by an oxalic acid-based sol–gel method

Potassium sodium niobate (KNN) ceramic powders by a variation of sol–gel method is synthesized. The metal precursors used for the KNN synthesis are potassium carbonate, sodium carbonate and niobium hydroxide, ethylene glycol are used as chelating and esterification agent, respectively. The effects of amount of oxalic acid (OA) and ethylene glycol (EG), pH value on the stability of the precursor sol were investigated. The evolution of (K_0.5Na_0.5)NbO₃ crystal phase was also investigated by XRD, IR, SEM and TG-DTA. The results showed that stable precursor sol was formed when n_(OA):n_(Mn+) = 3:1, n_(OA):n_(EG) = 1:2 and pH value was in the range of 2.5–3.5. Xerogel was sintered in the range of 500–650 °C to prepare K₆Nb_10.88O₃₀ and Na₂Nb₄O₁₁ powder. Then the compound was sintered at 750 °C to produce perovskite (K_0.5Na_0.5)NbO₃ ceramic powders. The grain size is about 100–200 nm.     

Application of mechanochemical activation for synthesis of uranium–lanthanoid mixed oxides

The applicability of mechanochemistry to produce uranium–lanthanoid mixed oxides is presented. Phase homogeneous uranium–cerium solid solutions of the type Ce _x U_1−x O₂ (x = 0.3 ÷ 0.95) and polyphase systems containing La _y U_1−y O_2+x (y = 0.12) were prepared by mechanochemical activation in air of sol–gel produced precursors. The possibility for synthesis of urania–lanthania solid solution by mechanochemical interaction of La₂O₃ with sol–gel produced U (IV,VI) oxide is established. The crystal structures of the obtained oxides before and after the mechanochemical treatment are analysed by the use of X-ray diffraction method. The size of the crystallites (8–16 nm), lattice parameters, crystallite strains and densities of the oxides are calculated by BRASS program for Rietveld calculation.     

Thermal properties of Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–PbO–P<Subscript>2</Subscript>O<Subscript>5</Subscript> glass system

Thermal behavior of xGa₂O₃–(50 − x)PbO–50P₂O₅ (x = 0, 10, 20, and 30 mol.% Ga₂O₃) and xGa₂O₃–(70 − x)PbO–30P₂O₅ (x = 0, 10, 20, 30, and 40 mol.% Ga₂O₃) glassy materials were studied by thermo-mechanical analysis (TMA) and differential thermal analysis (DTA). Replacement of PbO for Ga₂O₃ is accompanied by increasing glass-transition temperature (263 ≤ T _g/°C ≤ 535), deformation temperature (363 ≤ T _d/°C ≤ 672), crystallization temperature (396 ≤ T _c/°C ≤ 640) and decreasing of coefficient of thermal expansion (5.1 ≤ CTE/ppm K⁻¹ ≤ 16.7). Values of Hruby parameter were determined (0.1 ≤ K _H ≤ 1.3). The thermal stability of prepared glasses increases with increasing of concentration of Ga₂O₃.     

The influence of humic acid on the pH-dependent sorption of americium(III) onto kaolinite

This work investigates the sorption of americium [Am(III)] onto kaolinite and the influence of humic acid (HA) as a function of pH (3–11). It has been studied by batch experiments (V/m = 250:1 mL/g, C _Am(III) = 1 × 10⁻⁵ mol/L, C _HA = 50 mg/L). Results showed that the Am(III) sorption onto the kaolinite in the absence of HA was typical, showing increases with pH and a distinct adsorption edge at pH 3–5. However in the presence of HA, Am sorption to kaolinite was significantly affected. HA was shown to enhance Am sorption in the acidic pH range (pH 3–4) due to the formation of additional binding sites for Am coming from HA adsorbed onto kaolinite surface, but reduce Am sorption in the intermediate and high pH above 6 due to the formation of aqueous Am-humate complexes. The results on the ternary interaction of kaolinite–Am–HA are compared with those on the binary system of kaolinite–HA and kaolinite–Am and adsorption mechanism with pH are discussed. Effect of different molecular weight of HA, with three HA fractions separated by ultrafiltration techniques, on the Am sorption to kaolinite were also studied. The results showed that the enhancement of the sorption of Am onto kaolinite at the acidic pH conditions (pH 3–4) was higher with HA fractions of higher molecular weight. Also, the Am sorption over a pH range from 6 to 10 decreased with decreasing molecular weight of HA.     

Stable α-heteroatom-free dialkylcarbenes: a DFT study

The stability of the singlet dicyclopropylcarbene (ΔE _S–T = 15.3 kcal/mol, 1) is increased not only by cyclization to 2,5-dicyclopropylcyclopentanylidene (ΔE _S–T = 20.3 kcal/mol, 2), but even more so by unsaturation to 2,5-dicyclopropylcyclopentenylidene (ΔE _S–T = 22.5 kcal/mol, 3). In a further attempt to pave the way toward synthesis of new stable dialkylcarbenes, we introduced different substituents on the α-cyclopropyls of 3, where the stability was increased over twice of 1 (ΔE _S–T = 37.8 kcal/mol) for 2,5-bis(2,3-dihydroxycyclopropyl)-3,4-dinitrocyclopentenylidene, 3_{\textOH-\textNO 2} {\mathbf{3}}_{{{\text{OH}}{-}{\text{NO}}_{ 2}}} .     

Low-temperature combustion synthesis of CuCr2O4 spinel powder for spectrally selective paints

CuCr₂O₄ spinel powder with high quality black hue, investigated as solar-absorbing pigment for spectrally selective paint, was synthesized by an environmental friendly sol–gel combustion process using citric acid as the fuel and metal nitrates as oxidizers. Single-phase CuCr₂O₄ spinel crystals were obtained after heat treatment of the as-burnt powder at a low temperature (600 °C) and the average crystallite size of the CuCr₂O₄ powders increased with the calcining temperature. Morphological analysis of powders calcined at various temperatures was done by field emission scanning electron microscopy. CuCr₂O₄ powder calcined at 700 °C was chosen as pigment to fabricate thickness sensitive spectrally selective paint coatings by simple spray-coating technique. For the sake of comparison, the as-burnt powder composed of mixed metal oxides (i.e., CuO and Cr₂O₃) was also used as pigment. The results reveal that the spinel CuCr₂O₄ based paint coatings exhibit much higher spectral selectivity (α _s = 0.88–0.91, ε ₁₀₀ = 0.27–0.35) which is depending on the coating thicknesses than that of coatings using as-burnt powder as pigment (α _s = 0.83–0.88, ε ₁₀₀ = 0.60–0.66). The CuCr₂O₄-based paint coatings showed no visible degradation after 600 h of condensation test and the performance criterion value is 0.04, indicating that the coatings have excellent long term stability.     

Structure and dielectric properties of 80%Pb(Zn1/3Nb2/3)O3–20%PbTiO3 thin films prepared by modified sol–gel process

80%Pb(Zn_1/3Nb_2/3)O₃–20%PbTiO₃ (PZN–PT) thin films have been prepared on Pt/Ti/SiO₂/Si substrates using a modified sol–gel method. In our method, niobium pentaoxide is used as a substitution instead of niobium ethoxide which is moisture-sensitivity and much more expensive. Microstructure and electrical properties of PZN–PT thin films have been investigated. X-ray diffraction analysis shows that proper annealing temperature of PZN–PT thin films is 600 °C. The PZN–PT thin films annealed at 600 °C are polycrystalline with (111)-preferential orientations. Field-emissiom scanning electron microscope analysis revealed PZN–PT thin films possess well-defined and crack-free microstructure. The thickness of thin films is 290 nm. The Pt/PZN–PT/Pt capacitors have been fabricated and it presents ferroelectric nature. The remanent polarization (Pr), spontaneous polarization (Ps), and the coercive electric field (Ec) are 8.71 μC/cm², 43.06 μC/cm², and 109 kV/cm at 1 MHz, respectively. The dielectric constant (ε_r) and the dissipation factor (tan δ) are about 500.3 and 0.1 at 1 kHz, respectively.     

Sandwich-type Uranium-Substituted of Bismuthotungstate: Synthesis and Structure Determination of [Na(UO2)2(H2O)4(BiW9O33)2]13?

The sandwich-type [Na(UO₂)₂(H₂O)₄(BiW₉O₃₃)₂]¹³⁻ uranium (VI) has been synthesized by reacting the trivacant species of B-α-[BiW₉O₃₃]⁹⁻ with and investigated by IR and UV–Vis spectroscopy, and elemental analysis. The X-ray single crystal analysis was carried out on Na₁₃[Na(UO₂)₂(H₂O)₄(BiW₉O₃₃)₂] · 33H₂O (I) which crystallizes in the orthorhombic system, space group Pna2₁ with a = 33.8454(19) ?, b = 21.1484(12) ?, c = 13.2403(7) ?, α = 90°, β = 90°, γ = 90°, and Z = 4. The polyanion consists of two lacunary B-α-[BiW₉O₃₃]⁹⁻ groups which sandwich two uranyl cations and one sodium cation. The uranium atoms adopt distorted pentagonal–bipyramidal coordination, achieved by two equatorial bonds to each BiW₉O₃₃ unit and one external water ligand. The coordination of each uranium atom is evident by the shift of ν_as(W–O_b–W) and ν_as(Bi–O) stretching vibrational bonds. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Structural characterization of amorphous and nanostructured bismuth silicate xerogels

Bismuth silicate xBi₂O₃·(1 − x)SiO₂ xerogels, 0 ≤ x ≤ 0.5, doped with gadolinium have been synthesized by sol–gel method. The study aims to evidence by X-ray diffraction (XRD), electron paramagnetic resonance (EPR) and nuclear magnetic resonance (NMR) the structural changes in amorphous Bi₂O₃–SiO₂ xerogels, function of Bi₂O₃ content and heat treatment. As was proved by XRD, nanostructured samples were obtained after 30 min heat treatment at 400 °C of the as-prepared samples with x > 0, in the mainly amorphous matrices nanocrystals of Bi_5.6Si_0.5O_9.4 phase being developed. The dimension of the nanocrystallites are function of the bismuth content, and vary from few nanometers to 25 nm for samples with x = 0.14 and x = 0.5 respectively. The local order around silicon, reflected by 29Si MAS NMR spectra, is less dependent on both composition and thermal history of the samples, showing that an amorphous silicon rich phase is present in all samples. The changes in the local order around Gd³⁺ ions, as reflected by the EPR spectra dependence on composition and especially on the heat treatment, support the assumption that a part of these paramagnetic ions is incorporated in the bismuth rich phase.     

Effects of Fe-doping of ceria-based materials on their microstructural and dynamic oxygen storage and release properties

The structural/textual characteristics and dynamic oxygen storage capacity (DOSC) of Fe_0.1Ce_0.9O_x and Fe_0.1Ce_0.6Zr_0.3O_x samples prepared by sol–gel method are investigated by X-ray powder diffraction (XRD), Raman, Hydrogen temperature-programmed reduction (H₂-TPR), X-ray photoelectron spectroscopy (XPS) and mass spectrometry with CO/O₂ transient pulses. The dynamic oxygen storage capacity and rate are largely promoted by Fe doping, and their thermal stability is enhanced by Fe and Zr co-doping. The DOSC (at 673 K) are ordered as: Fresh: Fe_0.1Ce_0.6Zr_0.3O_x (566.6 μmol/g) > Fe_0.1Ce_0.9O_x (551.8 μmol/g) > Ce_0.67Zr_0.33O₂ (287.5 μmol/g) > CeO₂ (140.3 μmol/g); Annealed_1,173K: Fe_0.1Ce_0.6Zr_0.3O_x (101.6 μmol/g) > Ce_0.67Zr_0.33O₂ (45.3 μmol/g) > Fe_0.1Ce_0.9O_x (44.9 μmol/g) > CeO₂ (43.3 μmol/g). The H₂-TPR results showed that Fe-incorporation improve the total oxygen storage capacity (TOSC) of mixed oxide and low temperature activity. The TOSC are ordered as: Fe_0.1Ce_0.9O_x (1.53 mmol/g) > Fe_0.1Ce_0.6Zr_0.3O_x (1.42 mmol/g) > Ce_0.67Zr_0.33O₂ (1.16 mmol/g) > CeO₂ (0.88 mmol/g). XRD and Raman results indicate that Fe_0.1Ce_0.9O_x and Fe_0.1Ce_0.6Zr_0.3O_x are characterized with the fluorite-type cubic structure similar to CeO₂. TPR and XPS analyses reveal that the introduction of Fe into ceria and ceria-zirconia mixed oxides strongly modified the structural and textural properties, which influenced the kinetics of bulk oxygen diffusion.     

Electric-field-induced antiferroelectric to ferroelectric and ferroelectric to paraelectric phase transition at various temperatures in (Pb,La)(Zr,Ti)O<Subscript>3</Subscript> antiferroelectric thick films

(Pb, La)(Zr, Ti)O₃ antiferroelectric thick films with (100)-preferred orientation were fabricated on Pt(111)/Ti/SiO₂/Si(100) substrates via a sol–gel method. The electric-field-induced antiferroelectric (AFE) to ferroelectric (FE) phase transition characteristics were studied by C (capacitance)–E (electric field) measurements at different temperature. The films were in AFE state under 0 kV/cm below 122 °C, and the switching field values decreased, with increasing temperature. The films were in FE state between 122 and 135 °C, and when the temperature above 135 °C, the films were in PE state. The temperature-dependent dielectric parameters were deconvoluted using a Gaussian fit multi-peaks showed that two typical phase transitions were discovered. The first peak is the AFE-to-FE phase transition and the second peak is the FE-to-PE phase transition which has been verified by C–E tests.     

A study of the aerobic reaction between dopamine and Fe(III) in the presence of S<Subscript>2</Subscript>O<Subscript>3</Subscript><Superscript>2−</Superscript>

The reaction between Fe(III) and dopamine in aqueous solution in the presence of Na₂S₂O₃ was followed through UV–Vis spectroscopy, pH and oxy-reduction potential (Eh) measurements. The formation and quick disappearing of the complex [Fe(III)HL¹⁻]²⁺, HL¹⁻ = monoprotonated dopamine was observed with or without S₂O₃ ²⁻ at pH 3. An unexpected reaction occurs in presence of thiosulfate forming the stable anion complex [Fe(III)(L²⁻)₂]¹⁻, L²⁻ = dopacatecholate (λ = 580 nm) and the auto-increasing of the pH, from 3 to 7. It was proposed that H⁺ and molecular oxygen are consumed by free radical thiosulfate formed during the reaction.     

Low temperature preparation and electric properties of highly (100)-oriented Pb<Subscript>0.8</Subscript> La<Subscript>0.1</Subscript>Ca<Subscript>0.1</Subscript>Ti<Subscript>0.975</Subscript>O<Subscript>3</Subscript> thin films prepared by a sol–gel route

Highly (100)-oriented Pb_0.8La_0.1Ca_0.1Ti_0.975O₃ (PLCT) thin films deposited on Pt/Ti/SiO₂/Si substrate were successfully achieved by a sol–gel route. The influence of annealing temperature on microstructures and electric properties was investigated; it was found that the PLCT film could be crystallized only at 450 °C. When the annealing temperature increased to 500 °C, the PLCT film exhibited highly (100)-oriented, which also possessed higher remnant polarization Pr (27 μC/cm²) and better pyroelectric figure of merit (F _d = 205 μC/m²k) at room temperature. It was also found too high annealing temperature (625 °C) could lead to recrystallization of film, and the small grains caused by recrystallization could make polarization reversal difficult and disturbed the preferred crystal growth in film, which was not benefit to obtain enhanced electric properties.     

Some studies on the phase formation and kinetics in TiO<Subscript>2</Subscript> containing lithium aluminum silicate glasses nucleated by P<Subscript>2</Subscript>O<Subscript>5</Subscript>

Lithium aluminum silicate (LAS) glasses of compositions (wt%) 10.6Li₂O–71.7SiO₂–7.1Al₂O₃–4.9K₂O–3.2B₂O₃–1.25P₂O₅–1.25TiO₂ were prepared by the melt quench technique. Crystallization kinetics was investigated by the method of Kissinger and Augis–Bennett using differential thermal analysis (DTA). Based on the DTA data, glass ceramics were prepared by single-, two-, and three-step heat treatment schedules. The interdependence of different phases formed, microstructure, thermal expansion coefficient (TEC) and microhardness (MH) was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), thermo-mechanical analysis (TMA), and microhardness (MH) measurements. Crystallization kinetics revealed that Li₂SiO₃ is the kinetically favored phase with activation energy of 91.10 kJ/mol. An Avrami exponent of n = 3.33 indicated the dominance of bulk crystallization. Based upon the formation of phases, it was observed that the two-stage heat treatment results in highest TEC glass ceramics. The single-step heat treatment yielded glass ceramics with the highest MH.     

Structural and thermal properties of monolithic silica–phosphate (SiO<Subscript>2</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>) gel glasses prepared by sol–gel technique

A sol–gel process for producing monolithic silica–phosphate (SiO₂–P₂O₅) system different concentrations of P₂O₅, starting with tetra-ethoxysilane TEOS, and triethyl-phosphate as sources of SiO₂ and P₂O₅ was performed. The gels were heat-treated at temperatures ranging from 100 up to 900 °C. The structural and chemical analyses of the samples were determined by using X-ray diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). It was found from the XRD that the existence of phosphorus enhances the crystallization of silica gel, while the FTIR indicated the main functional groups of silica–phosphate. It is important to study the effect of hydroxyl in silica–phosphate glass. The results obtained are promising to use the prepared samples in a variety of applications, ranging from traditional application such as lighting products) to the modern application (such as optical fibers. Optical studies were measured by using the spectrophotometer in wavelength range 0.2–2.5 μm. The refractive index (n) was calculated for the prepared samples, it was found to be strongly affected by structural rearrangement resulting from the elimination of the solvent and the Si–OH, Si–O–Si and Si–O–OH bonding by phosphate and aluminum and it increases by increasing phosphate concentrations. The weight losses have investigated for prepared samples.     

Synthesis,characterization, and 2,4-dichlorophenoxyacetic acid degradation on In-Na<Subscript>2</Subscript>Ti<Subscript>6</Subscript>O<Subscript>13</Subscript> sol–gel prepared photocatalysts

Indium-Na₂Ti₆O₁₃ doped semiconductors were prepared by the sol–gel method using titanium and sodium alkoxides as precursors. The gelled samples were annealed at 700 °C for 4, 6, and 8 h, and then characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and UV–Vis diffused reflectance spectroscopy (DRS). XRD patterns of the samples show the formation of the Na₂Ti₆O₁₃ phase, whose crystallinity depends on the annealing time. The band gap calculated from the UV–Vis Kubelka–Munk function report similar values (3.2–3.4 eV) for all of the samples annealed at different times. SEM observations of the semiconductors showed microfiber bundle morphologies of about 5 μm. Meanwhile, by EDS analysis, indium oxide highly homogeneously dispersed on the hexatitanate surface was identified. The evaluation of the In-Na₂Ti₆O₁₃ semiconductors in the 2,4-dichlorophenoxyacetic acid (2,4-D) photodecomposition using ultraviolet light (λ = 254 nm) irradiation show that the photoactivity of the solids depends on the annealing time applied to the samples. The role of indium oxide is related to the indium oxide dispersed on the surface of the titanate diminishing the electron-hole recombination rate.     

Synthesis and characterization of spinel-type CuAl<Subscript>2</Subscript>O<Subscript>4</Subscript> nanocrystalline by modified sol–gel method

Nanocrystalline Copper aluminate (CuAl₂O₄) was prepared by sol–gel technique using aluminum nitrate, copper nitrate, diethylene glycol monoethyl ether and citric acid were used as precursor materials. This method starts from of the precursor complex, and involves formation of homogeneous solid intermediates, reducing atomic diffusion processes during thermal treatment. The formation of pure crystallized CuAl₂O₄ nanocrystals occurred when the precursor was heat-treated at 600 °C in air for 2 h. The stages of the formation of CuAl₂O₄, as well as the characterization of the resulting compounds were done using thermo–gravimetric analysis, X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. The products were analyzed by transmission electron microscopy and ultraviolet–visible (UV–Vis) spectroscopy to be round, about 17–26 nm in size and E _g = 2.10 eV.     

Preparation and dielectric properties of highly preferred-(100) orientation (Pb,La)(Zr,Ti)O<Subscript>3</Subscript> antiferroelectric thick films by sol–gel processing

Pb_0.97La_0.02Zr_0.95Ti_0.05O₃ (PLZT) antiferroelectric thick films of highly preferred-(100) orientation with different thickness were successfully deposited on Pt(111)/Ti/SiO₂/Si(100) substrates depending on the sol–gel process technique. The effects of the PLZT thick films in the preparation and electric properties are investigated. The films show polycrystalline perovskite structure with a (100) preferred orientation by X-ray diffractometer analyses. The antiferroelectric nature of the thick films is demonstrated by P (polarization)–E (electric field). The temperature dependence of the dielectric constant and dielectric loss displays the similar behavior in both cases at 100 kHz while the values of polarization characteristic are decreased with the increase of the film thickness. The phase switching current are studied as a function of a gradually change dc electric field and the voltage dependent current density of the most highly (100)-oriented PLZT film is 1.49 × 10⁻⁸ A/cm² over electric field range from 0 to ±261 kV/cm. The film at 2,498 nm exhibits excellent dielectric properties and highly preferred-(100) orientation.