Determination of arsenic in plant samples by inductively coupled plasma atomic emission spectrometry with ultrasonic nebulization: a complex problem

Under well-defined conditions, the analysis of most trace elements by inductively coupled plasma atomic emission spectrometry with ultrasonic nebulization (ICP-AES-USN) leads to accurate results for environmental matrices usually studied. Due to differences in matrix composition between standards and samples, ICP-AES-USN determinations of arsenic are interfered with by changes that take place mainly within the desolvation stage of the USN device. In this work, effects of plant matrices on the determination of As in six arsenic species have been investigated. Firstly, interferences were simulated by measuring analyte (species) signals in solutions containing variable concentrations of the main matrix elements encountered in mineralized plant samples (K, Ca, Mg, P and Na). Secondly, the influence of real plant matrices on emission signals of arsenic species was also studied. In this case, the observed effects were different than for individual matrix elements considered separately: Ca and Mg always present in real samples efficiently compensate the undesirable effects. Validation of this statement has been performed using mineralized plant reference materials. In addition, ICP-AES-USN results have been compared with those obtained by Zeeman electrothermal atomic absorption spectrometry.     

Feasibility of ETV-ICP-OES for Characterization of Archaeological Glasses

In the present study the possibilities of electrothermal vaporization inductively coupled plasma optical emission spectrometry (ETV-ICP-OES) for characterization of archaeological glasses were investigated. The objects of our research were fragments of a colorless late antique Roman flat window glass (fifth century A.D.) and colored medieval glass bracelets (eleventh–twelfth century A.D.) excavated in the region of Pernik (West Bulgaria).

The finely ground glass samples were analyzed directly and CHF₃ was used as evaporation and transport modifier. Dried aqueous standard solutions and certified reference materials with different matrix (glass, fly ash, and stream sediment) were used as calibration standards. No matrix effects were observed by the optimized conditions. Measurements were performed using common calibration curves obtained with all appropriate calibration standards and major, minor, and trace element concentrations were determined. ETV-ICP-OES analytical data were used to establish the type of glass, the fluxing agents, the typical coloring and decoloring elements, and the recipe norm.     

Reduction des interferences sur la determination des metaux lourds dans les sediments de cours d'eau et les boues de stations d'epuration par spectrometrie d'absorption atomique en four graphite

(Reduction of interferences in the determination of trace heavy metals in river sediments and sewage sludges by electrothermal atomic absorption spectrometry.)The interferences of synthetic matrices of river sediments and sewage sludges in the determination of lead, copper, cadmium, chromium and nickel by electrothermal atomic absorption spectrometry were studied; Pb, Cd and Ni were the most sensitive to interferences. The effects of hydrochloric, nitric, perchloric and hydrofluoric acids were tested; perchloric acid was found to interfere most during the determinations. Hydrofluoric acid must be eliminated by evaporation. Techniques for reducing chemical interferences were evaluated. The best method was found to be matrix modification with ammonium dihydrogenphosphate and ascorbic acid for the determination of lead and nickel, and rapid heating (Max Power) for the determination of cadmium. Determinants of copper and chromium were less prone to interference.     

Trends in sorption preconcentration combined with noble metal determination.

Nowadays much attention is being paid to the determination of trace amounts of noble metals in geological, industrial, biological and environmental samples. The most promising techniques, such as inductively coupled plasma atomic emission spectrometry (ICP-AES), inductively coupled plasma mass spectrometry (ICP-MS) and electrothermal atomic absorption spectrometry (ETAAS) are characterized by high sensitivity. However, the accurate determination of trace noble metals has been limited by numerous interferences generated from the presence of matrix elements. To decrease, or eliminate, these interferences, the sorption preconcentration of noble metals is often used prior to their instrumental detection. A great number of hyphenated methods of noble metal determination using sorption preconcentration have been developed. This review describes the basic types of available sorbents, preconcentration procedures and preparations of the sorbent to the subsequent determination of noble metals. The specific features of instrumental techniques and examples of ETAAS, FAAS, ICP-AES, ICP-MS determinations after the sorption preconcentration of noble metals are considered. The references cited here were selected mostly from the period 1996 - 2006.     

X-Ray fluorescence analysis of trace elements in fruit juice

X-Ray fluorescence spectrometry is applied to the determination of trace elements in fruit juice characterized by a high content of sugar and other soluble solid substances. Samples are prepared by evaporation, carbonization and pressing into discs. The synthesis of standards is described in detail. All element concentrations are directly estimated from linear calibration curves obtained without any matrix correction. The results of the analysis are in good agreement with those given by inductively coupled plasma-atomic emission spectrometry and atomic absorption spectrometry techniques.     

Chemometric tools improving the determination of anti-inflammatory and antiepileptic drugs in river and wastewater by solid-phase microextraction and liquid chromatography diode array detection

An analytical method for the simultaneous determination of seven non-steroidal anti-inflammatory drugs (naproxen, ketoprofen, diclofenac, piroxicam, indomethacin, sulindac and diflunisal) and the anticonvulsant carbamazepine in river and wastewater is reported. The method involves pre-concentration and clean-up by solid-phase microextraction using polydimethylsiloxane/divinylbenzene fibers, followed by liquid chromatography with diode array detection analysis. Owing to the fact that river water samples did not contain interferences and no sensitivity changes due to sample matrix were observed, external calibration was implemented. Standardization was also applied in order to carry out the prediction step by preparing only two diluted standards that were subjected to the pre-concentration step and a set of standards prepared in solvent. For the analysis of wastewater samples, in contrast, it was necessary to implement standard addition calibration in combination with the multivariate curve resolution-alternating least squares (MCR-ALS) algorithm, which allowed us to overcome matrix effect and exploit the second order advantage. Recoveries ranging from 72% to 125% for all pharmaceuticals proved the accuracy of the proposed method in river water samples. On the other hand, wastewater sample recoveries ranged from 83% to 140% for all pharmaceuticals, showing an acceptable performance – considering this sample contains no modeled interferences.     

Account of Matrix Effects in the Spectrometric Determination of Trace Elements Using the Single-Point Standard Addition Method

Journal of Analytical Chemistry - Possibilities of taking into account matrix effects in the determination of trace elements by electrothermal atomic absorption spectrometry and inductively coupled...     

Determination of manganese by graphite furnace atomic absorption spectrometry: matrix effect control by multiple linear regression model

The multivariate interference effects due to nitrates of sodium, potassium, magnesium and calcium on electrothermal atomization of manganese were modelled by using the multiple linear regression method in conjunction with a suitable experimental design. Since the model proved to be able to efficiently predict the simultaneous effects of the considered salts in a wide range of concentrations, it was applied to provide a computational correction of the matrix effects occurring in the ETAAS analysis of manganese in seawater, after preconcentration of the analyte on Chelex-100 resin and elution with nitric acid. Preliminary results showed that the matrix effects are significantly reduced, leading to an improvement in accuracy of the ETAAS analysis.     

Influence of sample matrix components on the selection of calibration strategies in electrothermal vaporization inductively coupled plasma mass spectrometry

Quantification of both digested and slurry samples were studied using ultrasonic slurry electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS). The results of external calibration using aqueous standards, method of additions, and In as an internal standard were compared. The elements studied include: Mn, Ni and Cu and the materials analyzed include: NIST SRM 1548 total diet and SRM 1549 milk powder. Palladium was used as a physical carrier and oxygen ashing was used to remove the organic part of the slurry matrix. Different degrees of matrix suppression effects were observed when different skimmer cones were employed. Aging of the skimmer cone and consequent loss of its original circular symmetry and decrease in orifice size resulted in differences in sampling of the ion beam and changes in the degree of matrix effects were observed as the skimmer cone was rotated. The presence of matrix suppression effects is evidenced by strong suppressions in the Ar₂, C and analyte signals. When matrix suppression effects were present, the method of external calibration provided low recoveries (average accuracy 73 ± 12%), therefore it was necessary to use the method of additions to compensate for these problems, providing an average accuracy of 108 ± 13%. When matrix effects were absent, the external calibration method resulted in an average accuracy of 101 ± 16%.     

六极杆碰撞反应池–ICP–MS法测定海水中痕量金属元素

建立了直接稀释法测定海水中痕量金属元素Cr,Cu,Zn,Cd,Pb的方法。样品经稀释10倍后,使用基体匹配及内标校正,采用六极杆碰撞反应池–电感耦合等离子体质谱仪直接测定稀释后海水样品中的5种元素Cr,Cu,Zn,Cd,Pb。各元素在0.0~100μg/L范围内均呈现良好的线性关系,线性相关系数(r~2)均大于0.999 0,方法检出限为0.004~0.209μg/L。测定结果的相对标准偏差为2.4%~4.4%(n=6),加标回收率为92%~113%。该方法简单快捷,适用于近岸海水中痕量元素Cr,Cu,Zn,Cd,Pb的分析。     

Determination of rare earth elements and other trace elements (Y, Mn, Co, Cr) in seawater using Tm addition and Mg(OH)₂ co-precipitation

This paper reports on a novel procedure for determining trace element abundances (REE and Y, Cr, Mn, Co) in seawater by inductively coupled plasma sector field mass spectrometry (ICP-SFMS). The procedure uses a combination of pre-concentration using co-precipitation onto magnesium hydroxides and addition of thulium spike. The validity of the method was assessed onto 25 ml volumes of certified reference materials (NASS- and CASS-4) and in house seawater standard. Procedural blanks were determined by applying the same procedure to aliquots of seawater previously depleted in trace elements by successive Mg(OH)₂ co-precipitations, yielding estimated contributions to the studied samples better than 1.1% for all elements, with the exception of Cr (<3.3%) and Co (up to 8%). The reproducibility of the method over the six month duration of the study was smaller than 11% RSD for all the studied elements. Results obtained for NASS-5 and CASS-4 agree well with published working values for trace elements.     

Determination of As,Cd, Cu,Hg and Pb in biological samples by modern electrothermal atomic absorption spectrometry

Pollution from heavy metals has increased in recent decades and has become an important concern for environmental agencies. Arsenic, cadmium, copper, mercury and lead are among the trace elements that have the greatest impact and carry the highest risk to human health. Electrothermal atomic absorption spectrometry (ETAAS) has long been used for trace element analyses and over the past few years, the main constraints of atomic absorption spectrometry (AAS) methods, namely matrix interferences that provoked high background absorption and interferences, have been reduced. The use of new, more efficient modifiers and in situ trapping methods for stabilization and pre-concentration of these analytes, progress in control of atomization temperatures, new designs of atomizers and advances in methods to correct background spectral interferences have permitted an improvement in sensitivity, an increase in detection power, reduction in sample manipulation, and increase in the reproducibility of the results. These advances have enhanced the utility of Electrothermal atomic absorption spectrometry (ETAAS) for trace element determination at μg L⁻¹ levels, especially in difficult matrices, giving rise to greater reproducibility, lower economic cost and ease of sample pre-treatment compared to other methods. Moreover, the recent introduction of high resolution continuum source Electrothermal atomic absorption spectrometry (HR-CS-ETAAS) has facilitated direct solid sampling, reducing background noise and opening the possibility of achieving even more rapid quantitation of some elements. The incorporation of flow injection analysis (FIA) systems for automation of sample pre-treatment, as well as chemical vapor generation renders (ETAAS) into a feasible option for detection of As and Hg in environmental and food control studies wherein large numbers of samples can be rapidly analyzed. A relatively inexpensive approach with low sample consumption provide additional advantages of this technique that reaches figures of merit equivalent to Inductively coupled plasma mass spectrometry (ICP-MS). Herein is presented an overview of recent advances and applications of (ETAAS) for the determination of As, Cd, Cu, Hg and Pb in biological samples drawn from studies over the last decade.     

In-situ vaporization and matrix removal for the determination of rare earth impurities in zirconium dioxide by electrothermal vaporization inductively coupled plasma atomic emission spectrometry

A novel method for the determination of trace rare earth impurities in ZrO₂ powder has been developed based on electrothermal vaporization inductively coupled plasma atomic emission spectrometry. A polytetrafluoroethylene slurry was used as a fluorinating reagent to convert both the matrix (Zr) and the analytes (rare earth elements) into fluorides with different volatilities at a high temperature in a graphite furnace. The more volatile ZrF₄ was removed in-situ by selective vaporization prior to the determination of the analytes, removing matrix spectral interferences. Under optimum operating conditions, the absolute detection limits of the analytes varied from 0.04 ng (Yb) to 0.50 ng (Pr) with relative standard deviations less than 5%. The recommended approach has been successfully applied to the determination of trace rare earth impurities (La, Pr, Eu, Gd, Ho and Yb) in ZrO₂ powder and the results were in good agreement with those obtained by pneumatic nebulization inductively coupled plasma atomic emission spectrometry after the separation of the matrix using a solvent extraction procedure.     

一种用于电热蒸发-原子光谱的微型化固相萃取技术

与传统的液 液萃取相比 ,固 液萃取技术具有省时、溶剂用量少、不易乳化和高富集因子等优点[1],它可与各种检测方法联用[2 ],已在痕量无机物或有机物的分离富集与测定中广泛应用 .但是常规的固相萃取中的洗脱过程存在洗脱体积大 ,时间长及要求二次处理等缺点 ,这与电热蒸发 (ＥＴＶ)进样 /电感耦合等离子体原子发射光谱 /质谱 (ＩＣＰ ＡＥＳ/ＭＳ)和电热原子吸收光谱 (ＥＴＡＡＳ)很不匹配 .基于此 ,本文设计了一种填充有Ｐ5 0 7萃淋树脂 ( 1 40目 )的超微柱 ( 0 6μｍ(ｉ.ｄ .)× 1 0ｍｍ) .它既可用作分离富集柱 ,又可作为ＥＴＶ ＩＣＰ…     

Trace analysis of high-purity graphite by LA-ICP-MS

Laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) has been established as a very efficient and sensitive technique for the direct analysis of solids. In this work the capability of LA-ICP-MS was investigated for determination of trace elements in high-purity graphite. Synthetic laboratory standards with a graphite matrix were prepared for the purpose of quantifying the analytical results. Doped trace elements, concentration 0.5 microg g(-1), in a laboratory standard were determined with an accuracy of 1% to +/- 7% and a relative standard deviation (RSD) of 2-13%. Solution-based calibration was also used for quantitative analysis of high-purity graphite. It was found that such calibration led to analytical results for trace-element determination in graphite with accuracy similar to that obtained by use of synthetic laboratory standards for quantification of analytical results. Results from quantitative determination of trace impurities in a real reactor-graphite sample, using both quantification approaches, were in good agreement. Detection limits for all elements of interest were determined in the low ng g(-1) concentration range. Improvement of detection limits by a factor of 10 was achieved for analyses of high-purity graphite with LA-ICP-MS under wet plasma conditions, because the lower background signal and increased element sensitivity.     

Optimized simultaneous determination of several elements in human intestinal Caco-2 TC7 cells by inductively coupled plasma-mass spectrometry after closed vessel microwave digestion

A rapid procedure, based on closed vessels microwave digestion and inductively coupled plasma-mass spectrometry (ICP-MS), was evaluated to ascertain the effect of chronic exposure to cadmium on intracellular accumulation of minor and essential trace elements in cultured epithelial cells (Caco-2 TC7). For all measurements, the method of external calibration was used and 3 elements (Be, Sc, In) were selected as internal standards. Optimization procedures are discussed and results are presented for the total determination of 9 key analytes (Na, Mg, Ca, Cr, Mn, Cu, Zn, Mo, and Cd) in certified reference materials (CRMs) and 20 samples of Caco-2 TC7 cells long-term exposed to Cd. The performance characteristics of the analytical system were evaluated by calibration and linearity, limits of detection and quantitation, accuracy with spiking, trueness and repeatability with available CRMs. As a complement to the ICP-MS determinations, both available CRMs and cell samples were analyzed either by electro thermal- or flame atomic absorption spectrometry. The results were in good agreement with the ICP-MS results.     

Chemometric investigation of systematic error in the analysis of biological materials by flame and electrothermal atomic absorption spectrometry

Systematic errors observed when using flame atomic absorption spectrometry (FAAS) and electrothermal atomic spectrometry (ETAAS) for the analysis of biological solid materials (seafood products) were evaluated. The effect of the sample pre-treatment method (microwave-assisted acid digestion, ultrasound-assisted acid leaching and slurry sampling) as well as the number of times that a certain pre-treatment process is repeated, were two factors evaluated. They give information about the effect of the sample pre-treatment on the uncertainty in the analysis. In addition, the number of measurements (i.e., number of times that an acid digest, an acid leachate or aqueous slurry are analysed) and the calibration technique used (aqueous calibration method or standard addition technique) were other two variables taken into account. This last factor gives information about the effect of the calibration on the results, while the replicate measurements showed the repeatability. A fifth variable named as sample matrix tests the influence of the matrix sample on the systematic error through the use of different reference materials. This variable allows the study of the effect of the trace element concentrations on the uncertainty because the trace elements contents are different in each reference material. Experimental design and principal component analysis approaches were used as chemometric tools. It has been found that the use of the slurry sampling technique in ETAAS and FAAS and the determination of high element concentrations by ETAAS have led to poor precision.     

Determination of Hg in seawater by inductively coupled plasma mass spectrometry after on-line pre-concentration

A method for the determination of Hg in seawater by inductively coupled plasma mass spectrometry, after an on-line separation and pre-concentration, is described. The matrix separation was accomplished by retention of the Hg complex with the ammonium salt of O,O-diethyl dithiophosphoric acid on C₁₈ immobilized on silica in a micro-column. Before pre-concentration, the seawater sample was acidified with HNO₃ to 0.14 mol l⁻¹. Methanol was used as the eluent, which was introduced into the conventional pneumatic nebulizer of the instrument. External calibration with aqueous analytical solutions, submitted to the same procedure, was used. An enhancement factor of 16 was obtained, and the limit of detection was 5 ng l⁻¹. The sample consumption was 2.3 ml per determination, and the sampling frequency was 21 h⁻¹. The accuracy was tested by comparison with vapor generation inductively coupled plasma mass spectrometry. The agreement between the Hg concentrations measured by the two methods in the seawater samples was good.     

Example of a technique for evaluation of interferences caused by complicated sample matrix elements in ICP-AES determination

An example of a useful and rapid procedure for the evaluation of interferences caused by complicated sample matrices in inductively coupled plasma atomic emission spectrometry (ICP-AES) is described. Using simple acid-base standards, all the elements investigated were determined separately in complicated matrices with satisfactory results. Multiple linear regression was used to calculate the linear correction coefficients for each matrix element analyzed. Good analytical results improved still further when this correction method was used.     

Geoanalysis using plasma spectrochemistry – milestones and future prospects

Highlights of plasma spectrochemistry in geoanalysis are reviewed. The techniques are evaluated in terms of recent instrumental developments, calibration strategies, spectral and matrix interferences and analytical performance. While acid decomposition results in solutions containing low salt contents, this decomposition strategy is inappropriate for numerous sample types due to poor recoveries. On the other hand, alkali fusions result in total decomposition, but solutions containing high salt contents constrain the accuracy due to interference effects in the inductively coupled plasma (ICP), the sample introduction system, and in the quadrupole mass spectrometer interface. Therefore, practical limits of determination are evaluated in terms of salt tolerances. It is concluded that ICP-atomic emission spectrometry (AES) is employed mainly for the accurate determination of the major and minor elements and the more abundant trace elements. On the other hand, ICP-mass spectrometry (MS) is used mainly for the determination of trace elements and together with the possibility of obtaining some isotopic information, it profoundly enhances the capability for solving geochemical problems. Several methods of direct solid sample introduction are described. These include direct current (DC) arc emission spectroscopy (DC-AES), slurry nebulization (SN), spark ablation (SA), laser ablation (LA) and glow discharges (GD). These devices allow direct solid analysis of bulk samples, single minerals and inclusions.