Effect of Molecular Weight on Packing during Latex Film Formation

A UV-visible technique is used to study the evolution of transparency during film formation from latex particles. Latex particles with high and low molecular weight (HM and LM) polymethyl methacrylate (PMMA) are used to prepare films. Two sets of films with different latex content were prepared from HM and LM particles separately, by annealing PMMA particles above the glass transition temperature. Transmitted photon intensity, I(tr), from HM and LM films increased as the annealing temperature was increased. The increase in the transmitted photon intensity is attributed to the latex content (film thickness) for the annealed film samples. It is suggested that as the latex particles are packed (film thickness is increased) fewer voids or cracks are formed in the films. Positive and negative absorption coefficients are measured below and above 210 and 180 degrees C annealing temperatures for the HM and LM films. Packing coefficients are obtained for films in various latex contents. It is observed that LM particles are packed much easier than HM particles. Copyright 2001 Academic Press.     

Void closure and interdiffusion processes during latex film formation from surfactant-free polystyrene particles: a fluorescence study

This study reports a steady state fluorescence (SSF) technique for studying film formation from surfactant-free polystyrene (PS) latex particles. The latex films were prepared from pyrene (P)-labeled PS particles at room temperature and annealed at elevated temperatures for 5-, 10-, 20-, and 30-min time intervals above the glass transition (T(g)) temperature of polystyrene. During the annealing processes, the transparency of the film changed considerably. Scattered light (I(sc)) and fluorescence intensity (I(0P)) from P were measured after each annealing step to monitor the stages of film formation. Evolution of transparency of latex films were monitored using photon transmission intensity, I(tr). Scanning electron microscopy (SEM) was used to detect variation in the physical structure of annealed films. Onset temperature for film formation, T(0), void closure, T(v), and healing temperatures, T(h), were determined and corresponding activation energies were measured. Void closure and interdiffusion stages were modeled and related activation energies were determined.     

Interdiffusion of polymer chains during latex coating

The fluorescence method was used to study the interdiffusion of polymer chains during annealing of latex above its glass transition temperature (T_g). The latex film was prepared from mixture of naphthalene (N) (donor) and pyrene (P) (acceptor)-labeled poly(methyl methacrylate) (PMMA) latex particles. Heptane was used as the coalescent agent. A steady-state fluorescence technique was employed to measure the amount of direct nonradiative energy transfer from N to P during the interdiffusion of polymer chains across the particle–particle junction. Various latex films with different latex contents were used to measure the percentage critical occupation for the reliable steady-state fluorescence measurements. Diffusions activation energies in these latex films were measured and found to be around 30 kcal/mol, which was attributed to the backbone motion of PMMA chains.     

Time evolution of film formation from polystyrene particles: a percolation approach

This work reports the film formation process from surfactant-free polystyrene (PS) latex particles. Steady state fluorescence and photon transmission techniques were used to study the evolution of film formation. The films were prepared from fluorescein (F)-labeled PS latex particles at room temperature and annealed in 2.5-min-time intervals above the glass transition temperature (T _g) of PS. Fluorescence intensity (I _F) from F was measured after each annealing step to monitor the stages of film formation. Evolution of transparency of latex films was monitored by using the photon transmission intensity, I _tr. Drastic increase in I _tr and I _F above the critical annealing times, t _r and t _c, respectively, were attributed to the percolation behavior of the PS material. Critical exponents, β, of percolation clusters were measured and found to be around 0.31 and 0.37 for I _tr and I _F measurement, respectively, which were attributed to the site percolation model.     

Film formation from nano‐sized polystyrene latex particles

This work reports on the steady state fluorescence (SSF) technique for studying film formation from surfactant‐free, nano‐sized polystyrene (PS) latex particles prepared via emulsion polymerization. The latex films were prepared from pyrene (P)‐labeled PS particles at room temperature and annealed at elevated temperatures in 5, 10, 15, 20 and 30 min time intervals above the glass transition temperature (T_g) of PS. During the annealing processes, the transparency of the film was improved considerably. Monomer and excimer fluorescence intensities, I_P and I_E respectively, from P were measured after each annealing step to monitor the stages of film formation. Evolution of transparency of the latex films was monitored by using photon transmission intensity, I_tr. Void closure and interdiffusion stages were modeled and related activation energies were determined and found to be 10.3 and 50.3 kJ mol⁻¹. Void closure temperatures, T_v, were determined from the minima of I_tr value. Copyright © 2005 John Wiley & Sons, Ltd.     

Ceramic encapsulated latex composites

This work reports the encapsulation of latex particles in Al2O3-polystyrene (PS) composite films. These films were prepared from PS particles in Al2O3 dispersion at room temperature in various latex contents. Composite films were annealed at elevated temperatures in 10 min time interval above the glass transition temperature (Tg) of polystyrene. Transmitted photon intensities, I(tr) were monitored after each annealing step. AFM micrographs were also used to observe the physical changes of the composite films during annealing. It was observed that latex particles are encapsulated above a critical Al2O3 content of 33 wt% which corresponds to the critical occupation probability of p(c) = 0.33 at which the film obey the site-percolation model with a critical exponent of 0.45. Below p(c), it was seen that complete latex film formation process took place, where transparency of the film was increased by annealing.     

A photon transmission study for film formation from poly(vinyl acetate) latex particles with different molecular weights

The photon transmission technique was used to monitor the temperature evolution of film formation from poly(vinyl acetate) (PVAc) latex particles with two different molecular weights. Two sets of latex films were prepared below the glass transition temperature (T_g) of PVAc, which are named as low (LM) and high molecular weight (HM) films. These films were annealed at elevated temperatures above the T_g of PVAc for various time intervals. It is observed that transmitted photon intensity (I_tr) from these films increased as the annealing temperature was increased. Onset temperatures (T_H) at given times (τ_H) for starting the optical clarity of LM and HM films were measured and used to calculate the healing activation energies (ΔH) for the PVAc minor chains, and found to be as 28.1 kcal/mol and 27.7 kcal/mol, respectively. The increase in the transmitted photon intensity, I_tr above T_H was attributed to the increase in the number of disappeared interfaces between the deformed latex particles. Prager–Tirrell (PT) model was employed to interpret the increase in the crossing density of chains at the junction surfaces. The interdiffusion (backbone) activation energies (ΔE) were measured and found to be 177.5 kcal/mol and 210.7 kcal/mol for a diffusing PVAc chains across the junction surface of LM and HM latex films, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2918–2925, 2007     

Film Formation from Nanosized Copolymeric Latex Particles: A Photon Transmission Study

The photon transmission technique was used to monitor the evolution of transparency during film formation from nanosized copolymeric latex particles. The latex films were prepared from poly(methyl methacrylate-co-butyl methacrylate) (P(MMA-co-BMA)) particles which were produced by microemulsion polymerization. These films were annealed at elevated temperatures in various time intervals above the glass transition temperature (T(g)) of P(MMA-co-BMA). It is observed that the transmitted photon intensity (I(tr)) from these films increased as the annealing temperature increased. There are three different film formation stages. These stages are explained by the void closure, healing, and interdiffusion processes, respectively. The activation energies for viscous flow (DeltaH approximately 16 kcal/mol), minor chains (DeltaE(H) approximately 27 kcal/mol), and backbone motion (Delta E(b) approximately 132 kcal/mol) were obtained using various models. Void closure (tau(v), T(v)) and healing points (tau(H), T(H)) were determined. Using the time-temperature pairs, void closure and healing activation energies were measured and found to be 21 and 30 kcal/mol, respectively. Copyright 2001 Academic Press.     

Swelling of interpenetrating networklike particles in a soft polymer matrix

Fast transient fluorescence technique was used to monitor swelling of hard latex particles in a soft polymer matrix. Various film samples were prepared from pyrene (P) and/or naphthalene (N)-labeled poly(methyl methacrylate) (PMMA) particles in a low-molecular-weight poly(isobutylene) (PIB) matrix. These PMMA particles contain interpenetrating PIB channels. Film samples were annealed at elevated temperatures to promote particle swelling. Fluorescence lifetimes, tau, were measured for each film sample. It was observed that tau values decrease as the PIB content in the matrix is increased. The decrease in tau was explained by the increase in quenching of excited P and N molecules by low-molecular-weight PIB penetrating into the PIB channels in the PMMA particles. A drastic decrease in tau above a certain temperature was attributed to the effect of particle size on the swelling of the latex particles in the PIB matrix. It was observed that small particles (P-labeled) swell at much lower annealing temperatures than large (N-labeled) particles.     

Kinetics of latex formation of PBMA latex in the presence of alkali soluble resin using atomic force microscopy

 The effect of alkali-soluble resin (ASR), poly(ethylene-co-acrylic acid), EAA, postadded to emulsifier-free monodisperse poly(butyl methacrylate) (PBMA) latexes on the kinetics of film formation was investigated using atomic force microscopy (AFM). Corrugation height of latex particles in films was monitored at various annealing temperatures as a function of annealing time. Enhanced polymer diffusion was found in a latex film containing ASR regardless of anneal-ing temperature. With increasing annealing temperature, a much higher rate of polymer diffusion was found in latex films containing ASR. These results can be interpreted that the low molecular weight and low Tg EAA resin adsorbed at the particle surface is more susceptible to diffusion than that of the PBMA in the film formation stage, thus it enhances the mobility of PBMA polymer. Received: 30 October 1997 Accepted: 20 March 1998     

Latex film formation studied with the atomic force microscope: Influence of aging and annealing

The surface structure of latex dispersion films was examined with an atomic force microscope. All measurements were done in air on latex films having a minimum film formation temperature of 12°C and a glass transition temperature of 18°C. One aim of this study was to follow structural changes during film formation. Three minutes after spreading the film, its surface layer dried. Afterwards, the structure of the film did not change anymore. Only after 4 months could structural changes be observed: Though individual latex particles could be identified, the particles partly melted into one another.After annealing films at 50° or 60°C for 4 h, the latex particles partly melted into one another, but individual particles could still be identified. When annealing at or above 80°C, no individual latex particles were visible anymore. With increasing temperature the film roughness decreased from 3 nm without annealing to 0.8 nm at 100°C annealing temperature. In addition, islands of 2–4 nm thickness appeared on the film surface. These islands could be scraped off the film by increasing the force between tip and sample, indicating that they are composed of surfactant which was squeezed out of the film.     

EFFECT OF THE PHASE STRUCTURE EVOLUTION ON THE PROPERTIES OF FILMS FORMED FROM PBA/P(St-co-MMA) COMPOSITE LATEX

A group of heterogeneous latexes poly(butyl acrylate)/poly(styrene-co-methyl methacrylate)(PBA/P(St-co-MMA)) were prepared by a semi-continuous seeded emulsion polymerization process under monomer starved conditions.The glass transition temperature(T_g)and the mechanical properties of the film formed from the composite latex changed with the evolution of the particle morphology.A photon transmission method was used to monitor the phase structure evolution of films which were prepared from core-shell PBA/...     

Site percolation model for latex film formation in soft polymer matrix

The UV-visible (UVV) technique was used to monitor latex film formation in a soft polymer matrix. Various film samples were prepared by increasing the amount of poly(methyl methacrylate) (PMMA) particles in a poly(isobutylene) (PIB) matrix. These samples were then annealed above the glass transition temperature to promote latex film formation. Transmitted photon intensities, Itr, were measured for each film. It is observed that Itr decrease as the latex content is increased, which was explained by the increase in scattered light intensity, Isc. The drastic increase in Isc above a certain latex content is attributed to the site percolation of latex particles in the PIB matrix. The percolation threshold and the critical exponent were measured and found to be 0.3 and 0.4, respectively. The increase in Itr by annealing of film samples above Tg was explained with the void closure process below 0.8 occupation probability. When the film is occupied completely with the latex particles, interdiffusion of polymer chains was observed. Viscous flow and chain diffusion activation energies were determined and found to be 8 and 51 kcal/mol, respectively.     

Self-organization of polymer particles on hydrophobic solid substrates in aqueous media. I. Self-organization of cationic polymer particles on alkylated glass plates

Monodisperse, cationic polymer particles bearing quaternary ammonium groups effectively self-organized on hydrophobic solid substrates such as alkylated glass plates and polymer films to form particle monolayers. With an increase of the particle surface charge density, the surface coverage decreased and the morphology of particle monolayers changed from aggregated type to dispersed type. The dispersed type of particle monolayers having a relatively regular particle distance was formed at higher temperature. The self-organization behaviors on alkylated glass plates were different from those on unmodified glass plates through electrostatic interaction. The formation of particle monolayers on alkylated glass plates occurred only over a certain latex concentration range in contrast with that on unmodified glass plate. The adhesive strength of particle monolayers was enhanced by annealing at temperatures above the glass transition temperature (T _g) of the particles. Lens-shaped particle monolayers were fabricated by annealing the dispersed type of particle monolayers.     

Molecular Weight Effect on Latex Film Formation from Polystyrene Particles: A Photon Transmission Study

The photon transmission method was used to probe the time evolution of film formation from latex particles. Two different latex films were prepared from high molecular weight (HM) and low molecular weight (LM) polystyrene particles at room temperature and were annealed at various temperatures in 2.5-min time intervals above the glass transition. The increase in the transmitted photon intensity (Itr) is attributed to the increase in "crossing density" at the junction surface. The Prager-Tirrell model was employed to interpret the increase in crossing density at the junction surface. The back and forth activation energies were measured for HM and LM films and found to be around 59 and 87 kcal/mol for a reptating polymer chain across the junction surface. Monte Carlo simulations were performed for photon transmission through a rectangular lattice. The number of transmitted photons (Ntr) was calculated as a function of the mean free path of photons. It was observed that Ntr, similar to Itr, increases as the square of the mean free path of photons is increased. Copyright 1999 Academic Press.     

Latex film formation and dissolution: A fluorescence study

A new technique based on steady state fluorescence (SSF) measurements is introduced for studying dissolution of polymer films. These films are formed from naphthalene (N) and pyrene (P) labeled poly(methyl methacrylate) (PMMA) latex particles, sterically stabilized by polyisobutylene (PIB). Annealing was performed above T_g at elevated temperatures for 30 min time intervals for film formation. Film formation from these latexes is monitored by the extent of energy transfer from N to P using SSF and by the transmitted photon intensity from these films using UV visible (UVV) methods. Desorption of P labeled PMMA chains was monitored in real-time by the change of pyrene fluorescence intensity. Dissolution experiments were performed in various solvents with different solubility parameters, δ, at room temperature. Diffusion coefficients, D, in various solvents were measured and found to be around 10⁻¹⁰ cm²/s. Strong relationships between D and δ were observed. Diffusion activation energy was measured by performing dissolution experiments in toluene-heptane mixtures at elevated temperatures and determined to be 24.4 kcal mol⁻¹.     

Diffusion energies of oxygen diffusing into polystyrene (PS)/poly (N‐isopropylacrylamide) composites

Diffusion coefficient of oxygen penetrating into polystyrene (PS) latex/poly (N‐isopropylacrylamide) (PNIPAM) microgel composite films were measured using Fluorescence technique. Three different (5, 15, and 40 wt%) PS content films were prepared from PS/PNIPAM mixtures. Diffusivity of PS/PNIPAM composite films were studied by diffusion measurements which were performed over the temperature range of 24–70°C. Pyrene was used as the fluorescent probe. The diffusion coefficients (D) of oxygen were determined using the Stern–Volmer fluorescence quenching method combined with Fickian transport and were computed as a function of temperature for each PS content film. The results showed that D values were strongly dependent on both temperature and PS content in the film. Diffusion energies were measured and found to be dependent on the composition of the composite films. Copyright © 2011 John Wiley & Sons, Ltd.     

苝酰亚胺功能化聚苯乙烯乳胶粒水凝胶膜

将带有硼酸基团的苝酰亚胺荧光分子引入聚苯乙烯共聚乳胶粒表面,再将其嵌入聚丙烯酰胺水凝胶膜内,合成了对葡萄糖敏感的水凝胶膜。通过扫描电子显微镜、激光粒径分析仪对微球的外观形貌、单分散性进行表征,并用原子吸收光谱法间接测定了微球表面苝酰亚胺的含量,研究了苝酰亚胺功能化聚苯乙烯乳胶粒的紫外-可见吸收光谱图及其水凝胶膜的荧光性能。结果表明:苝酰亚胺功能化聚苯乙烯乳胶粒水凝胶膜经浓度逐渐增大的葡萄糖溶液浸泡后,其荧光强度降低,但发射峰位置不变。当葡萄糖浓度达到200 mmol/L时,其荧光淬灭效率为0.34。     

Film formation stages for poly(vinyl acetate) latex particles: a photon transmission study

Photon transmission technique was used to monitor the evolution of transparency during film formation from poly(vinyl acetate) (PVAc) latex particles. The latex films were prepared below the glass transition temperature (T _g) of PVAc. These films were annealed at elevated temperatures in various time intervals above the T _g of PVAc. It is observed that transmitted photon intensity (I _tr) from these films increased as the annealing temperature is increased. It is seen from I _tr curves that there are two film formation stages. These successive stages are named void closure (viscous flow) and interdiffusion. The activation energies for viscous flow (ΔH) and backbone motion (ΔE _b) were obtained by using well-defined models. The averaged values of the backbone (ΔE _b) and the viscous flow activation energies (ΔH) were found to be 188.6 and 5.6 kcal/mol, respectively. The minimum film formation (τ _M,T _M) and healing points (τ _H,T _H) were determined. Minimum film formation (ΔE _M) and healing activation energies (ΔE _H) were measured using these time–temperature pairs. ΔE _M and ΔE _H were found to be 32.5 and 28.3 kcal/mol, respectively.     

Film formation from pure and mixed latices; transient fluorescence study

A fast transient fluorescence technique was used to study latex film formation induced by organic solvent vapor. Mixtures of pyrene (P)- and naphthalene (N)-labeled and/or pure naphthalene-labeled latex films were prepared separately from poly(methyl methacrylate) (PMMA) particles. Then these pure and mixed latex films were exposed to vapor of various chloroform-heptane mixtures in seven different experiments. In both films, fluorescence lifetimes from N were monitored during vapor-induced film formation. It was observed that N lifetimes decreased as the vapor exposure time is increased. A Stern-Volmer kinetic analysis was used for low quenching efficiencies to interpret the decrease in N lifetimes. A Prager-Tirrell model was employed to obtain back-and-forth frequencies, nu, of reptating PMMA chains during latex film formation induced by solvent vapor. In both pure and mixed latex films, nu values were found to be correlated with the chloroform content in the vapor mixture. It was observed that polymer interdiffusion obeyed a t1/2 law during film formation.