SFE of PAHs from soils with a high carbon content and analyte collection via combined liquid/solid trapping

Polynuclear aromatic hydrocarbons (PAHs) are recovered from a soil with a high carbon content (ca. 50%) with supercritical fluid extraction (SFE) as well as with conventional Soxhlet extraction. The influence of temperature and modifier volume on SFE efficiency and the effect of a combined liquid/solid trap for analyte collection are investigated in this study. Such traps, which make analyte collection and clean-up possible in one step, are compared with conventional analyte collection in pure organic solvents. A comparison between reproducibility and efficiency of SFE and Soxhlet extraction is presented.     

Application of sulfur microparticles for solid-phase extraction of polycyclic aromatic hydrocarbons from sea water and wastewater samples

The application of sulfur microparticles as efficient adsorbents for the solid-phase extraction (SPE) and determination of trace amounts of 10 polycyclic aromatic hydrocarbons (PAHs) was investigated in sea water and wastewater samples using high performance liquid chromatography coupled with an ultraviolet detector (HPLC–UV). Parameters influencing the preconcentration of PAHs such as the amount of sulfur, solution flow rate and volume, elution solvent, type and concentration of organic modifier, and salt effect were examined. The results showed that at a flow rate of 10 mL min⁻¹ for the sample solutions (100 mL), the PAHs could be adsorbed on the sulfur microparticles and then eluted by 2.0 mL of acetonitrile. For HPLC–UV analysis of extracted PAHs, the calibration curves were linear in the range of 0.05–80.0 μg L⁻¹; the coefficients of determinations (r²) were between 0.9934 and 0.9995. The relative standard deviations (RSDs) for eight replicates at two concentration levels (0.5 and 4.0 μg L⁻¹) of PAHs were lower than 7.3%, under optimized conditions. The limits of detection (LODs, <!-- no-mfc -->S/N<!-- /no-mfc --> = 3) of the proposed method for the studied PAHs were 0.007–0.048 μg L⁻¹. The recoveries of spiked PAHs (0.5 and 4 μg L⁻¹) in the wastewater and sea water samples ranged from 78% to 108%. The simplicity of experimental procedure, high extraction efficiency, short sample analysis, and using of low cost sorbent demonstrate the potential of this approach for routine trace PAH analysis in water and wastewater samples.     

Water stability of zeolite imidazolate framework 8 and application to porous membrane-protected micro-solid-phase extraction of polycyclic aromatic hydrocarbons from environmental water samples

Zeolite imidazolate framework 8 (ZIF-8) has permanent porosity, high surface area, hydrophobic property, open metal sites and remarkable water stability. These novel properties characterize the material as being different from other moisture sensitive metal-organic frameworks and endow ZIF-8 with the potential to extract trace analytes from environmental water samples. In the present study, ZIF-8 was synthesized and used as a sorbent for micro-solid-phase extraction of 6 polycyclic aromatic hydrocarbons (PAHs) from environmental water samples for the first time. Parameters influencing the extraction efficiency such as desorption time, extraction time, desorption solvent and salt concentration were investigated. Environmental water samples collected from a local lake were processed using this novel μ-SPE procedure. ZIF-8 proved to be a very efficient extraction sorbent for the extraction of trace analytes from water samples. The limits of detection from gas chromatography-mass spectrometric analysis of PAHs were 0.002-0.012 ng/ml. The linear ranges were 0.1-50 or 0.5-50 ng/ml. The relative standard deviations for five replicates of the extractions were in the range of 2.1-8.5%.     

Sensitive determination of polycyclic aromatic hydrocarbons in water samples using monolithic capillary solid-phase extraction and on-line thermal desorption prior to gas chromatography-mass spectrometry

A methacrylate-based monolithic capillary column has been evaluated for the preconcentration of polycyclic aromatic hydrocarbons (PAHs) from environmental water samples. For this purpose, the monolyte was in situ synthesized in a 6cm×0.32mm id fused-silica capillary. The microextraction unit was fitted to a micro-HPLC pump to pass 10mL of sample. The isolated pollutants were eluted by means of 10μL of methanol, the organic phase being directly collected in a specific interface that can be fitted to the injection port of the gas chromatograph without modification. The interface allows the on-line thermal desorption of the PAHs, avoiding the dilution and providing enough sensitivity to reach the legal limits established for these pollutants in the matrices selected. The limits of detection achieved for 10mL of water ranged between 2.8ng/L (indeno(1,2,3-cd)pyrene) and 11.5ng/L (acenaphthene) with acceptable precision (between 4.5 and 18.2% RSD). The method was applied to the determination of the selected PAHs in tap, river waters and sewage, being fluoranthene and pyrene detected in all of them at concentrations lower than the legal limits established for these compounds in the matrices assayed.     

Analysis of polycyclic aromatic hydrocarbons (PAHs) in environmental samples: a critical review of gas chromatographic (GC) methods

Polycyclic aromatic hydrocarbons (PAHs) are frequently measured in the atmosphere for air quality assessment, in biological tissues for health-effects monitoring, in sediments and mollusks for environmental monitoring, and in foodstuffs for safety reasons. In contemporary analysis of these complex matrices, gas chromatography (GC), rather than liquid chromatography (LC), is often the preferred approach for separation, identification, and quantification of PAHs, largely because GC generally affords greater selectivity, resolution, and sensitivity than LC. This article reviews modern-day GC and state-of-the-art GC techniques used for the determination of PAHs in environmental samples. Standard test methods are discussed. GC separations of PAHs on a variety of capillary columns are examined, and the properties and uses of selected mass spectrometric (MS) techniques are presented. PAH literature on GC with MS techniques, including chemical ionization, ion-trap MS, time-of-flight MS (TOF-MS), and isotope-ratio mass spectrometry (IRMS), is reviewed. Enhancements to GC, for example large-volume injection, thermal desorption, fast GC, and coupling of GC to LC, are also discussed with regard to the determination of PAHs in an effort to demonstrate the vigor and robustness GC continues to achieve in the analytical sciences.     

超临界流体分级萃取正构烷烃和多环芳烃

本工作用超临界ＣＯ２对环境模拟样品中的正构烷烃和多环芳烃的超临界分级萃取方法及超临界ＣＯ２的压力，温度和用量对分级效率的影响进行了详细的研究。结果表明，在低压、低温下（８０ＭＰａ，５０℃）能成功地分级萃取正构烷烃和多环芳烃，其Ｃ１０～Ｃ１８的萃取率为９９．９４％～５９．２８％，而多环芳烃基本未被萃取。当压力升至２６．０ＭＰａ、温度升至８０℃时，可有效地萃取多环芳烃，实现了正构烷烃和多环芳烃的有效分离     

Optimisation of supercritical fluid extraction of polycyclic aromatic hydrocarbons and their nitrated derivatives adsorbed on highly sorptive diesel particulate matter

Supercritical fluid extraction (SFE) was performed to extract complex mixtures of polycyclic aromatic hydrocarbons (PAHs), nitrated derivatives (nitroPAHs) and heavy n-alkanes from spiked soot particulates that resulted from the incomplete combustion of diesel oils. This polluted material, resulting from combustion in a light diesel engine and collected at high temperature inside the particulate filter placed just after the engine, was particularly resistant to conventional extraction techniques, such as soxhlet extraction, and had an extraction behaviour that differed markedly from certified reference materials (SRM 1650). A factorial experimental design was performed, simultaneously modelling the influence of four SFE experimental factors on the recovery yields, i.e.: the temperature and the pressure of the supercritical fluid, the nature and the percentage of the organic modifier added to CO₂ (chloroform, tetrahydrofuran, methylene chloride), as a means to reach the optimal extraction yields for all the studied target pollutants. The results of modelling showed that the supercritical fluid pressure had to be kept at its maximum level (30 MPa) and the temperature had to be kept relatively low (75 °C). Under these operating conditions, adding 15% of methylene chloride to the CO₂ permitted quantitative extraction of not only light PAHs and their nitrated derivatives, but also heavy n-alkanes from the spiked soots. However, heavy polyaromatics were not quantitatively extracted from the refractory carbonaceous solid surface. As such, original organic modifiers were tested, including pyridine, which, as a strong electron donor cosolvent (15% into CO₂), was the most successful. The addition of diethylamine to pyridine, which enhanced the electron donor character of the cosolvent, even increased the extraction yields of the heaviest PAHs, leading to a quantitative extraction of all PAHs (more than 79%) from the diesel particulate matter, with detection limits ranging from 0.5 to 7.8 ng for 100 mg of spiked material. Concerning the nitrated PAHs, a small addition of acetic acid into pyridine, as cosolvents, gave the best results, leading to fair extraction yields (approximately 60%), with detection limits ranging from 18 to 420 ng.     

Development of multiwalled carbon nanotubes based micro-solid-phase extraction for the determination of trace levels of sixteen polycyclic aromatic hydrocarbons in environmental water samples

Micro-solid-phase extraction (μ-SPE) was developed for the determination of trace level of 16 United States Environmental Protection Agency priority polycyclic aromatic hydrocarbons (PAHs) in river water samples with gas chromatography-mass spectrometry (GC-MS). In the μ-SPE device, multiwalled carbon nanotubes was employed as sorbent and was packed inside an porous polypropylene membrane "envelope" whose edges were heat-sealed to secure the contents. The μ-SPE device was placed in a stirred sample solution to extract the analytes. The porous polypropylene membrane envelope in μ-SPE device acts as a filter to exclude potential interferences, such as eliminating or reducing the influence of particles that are bigger than the pore size. After extraction, analyte desorption was carried out with a suitable organic solvent under ultrasonication. Important extraction parameters were optimized in detail, including the selection and amount of sorbent materials, the extraction temperature and extraction time, desorption solvent and desorption time, amount of organic modifier, agitation speed and sample ionic strength. Under the developed extraction conditions, the proposed method provided good linearity in the range of 0.1-50 μg/L, low limits of detection (4.2-46.5 ng/L), and good repeatability of the extractions (relative standard deviations, <12%, n=5). The developed μ-SPE method was successfully applied to the extraction of PAHs in river water samples. The μ-SPE method was demonstrated to be a fast and efficient method for the determination of PAHs from environmental water samples.     

Fluidized-bed extraction of polycyclic aromatic hydrocarbons from contaminated soil samples

Summary Due to the carcinogenity and ubiquity of polycyclic aromatic hydrocarbons in the environment they are of ongoing interest to analytical chemistry. In this study, a comparison of the classic Soxhlet extraction and, fluidized-bed extraction, has been conducted. The extraction of polycyclic aromatic hydrocarbons by this technique has been optimized considering as experimental variables the variation of the number of extraction cycles and the holding time after reaching the heating temperature by means of a surface response design. The significance of the operational parameters of the fluidized-bed extraction on the performance characteristics has been investigated. For the determination of the analytes a selective clean-up of the extracts followed by a fast gas chromatography method with mass spectrometric detection was used, resulting in low limits of detection (0.2 pg μL⁻¹). The accuracy of the complete analytical method was established by extraction and analysis of reference materials.     

The quantitative effect of microextractor cell geometry on the analytical supercritical fluid extraction efficiencies of environmentally important compounds

Summary The quantitative effect of microextractor cell geometries on supercritical fluid extraction (SFE) efficiencies of polycyclic aromatic hydrocarbons (PAHs) and methoxychlor from octadecyl-bonded sorbents has been evaluated and compared to similar effects seen upon increasing the supercritical fluid density. For the PAHs studied, correlations between the fused ring number and the relative increase in recoveries have been established. SFE recoveries can be increased by greater than a factor of two by decreasing the diameter to length ratio from 120 to 11. The relative recovery increase upon decreasing the diameter to length ratio of the extraction vessel is dependent on the analyte extractability, increasing in proportion to the fused ring number for the PAHs. Recoveries increased linearly as a function of supercritical fluid density for the PAHs studied. The change in the relative recovery upon increasing the supercritical carbon dioxide density again was dependent on the analyte type, decreasing linearly with fused ring number. Although fluid density generally had the greatest effect on achievable SFE recoveries, the cell geometry had effects of a similar order of magnitude, highly dependent on the initial extractability of the analyte.     

Polyimide‐coated magnetic nanoparticles as a sorbent in the solid‐phase extraction of polycyclic aromatic hydrocarbons in seawater samples

Magnetic polyimide poly(4,4′‐oxydiphenylene‐pyromellitimide) nanoparticles were successfully synthesized and developed for the solid‐phase extraction of polycyclic aromatic hydrocarbons in seawater samples. The aromatic rings of polyimide coating provided a good adsorption capacity (28.3–42.5 mg/g) for polycyclic aromatic hydrocarbons because of the π–π stacking interaction. The developed method was used as a simple, fast, and efficient extraction and preconcentration technique for the trace analysis of polycyclic aromatic hydrocarbons. The high chemical, physical and thermal stability, excellent reusability, and good magnetic properties are the merits of the sorbent. High preconcentration factors (41–63) were obtained. The sorbent was also characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, energy dispersive X‐ray spectrometry, transmission electron microscopy, and vibrating sample magnetometry. After optimizing several appropriate extraction parameters, the results indicated that the extraction recoveries of polycyclic aromatic hydrocarbons were in the range of 61.6–94.7%, with relative standard deviations between 2.9 and 5.4%, the calibration graph was linear in the concentration range of 1–100 μg/L (r > 0.9991) with limit of detection in the range of 0.15–0.19 μg/L (n = 3). Seawater samples were analyzed as real samples and good recoveries (68.5–99.5%) were obtained at different spiked values.     

Analytical evaluation of BEA zeolite for the pre-concentration of polycyclic aromatic hydrocarbons and their subsequent chromatographic analysis in water samples

The analytical performance of BEA – a commercial zeolite – is evaluated for the pre-concentration of fifteen Environmental Protection Agency – polycyclic aromatic hydrocarbons and their subsequent HPLC analysis in tap and lake water samples. The pre-concentration factors obtained with BEA have led to a method with excellent analytical figures of merit. One milliliter aliquots were sufficient to obtain excellent precision of measurements at the parts-per-trillion concentration level with relative standard deviations varying from 4.1% (dibenzo[a,h]anthracene) to 13.4% (pyrene). The limits of detection were excellent as well and varied between 1.1 (anthracene) and 49.9 ng L⁻¹ (indeno[1,2,3-cd]pyrene). The recovery values of all the studied compounds meet the criterion for regulated polycyclic aromatic hydrocarbons, which mandates relative standard deviations equal or lower than 25%. The small volume of organic solvents (100 μL per sample) and amount of BEA (2 mg per sample) makes sample pre-concentration environmentally friendly and cost effective. The extraction procedure is well suited for numerous samples as the small working volume (1 mL) facilitates the implementation of simultaneous sample extraction. These are attractive features when routine monitoring of numerous samples is contemplated.     

Coupled SFE/SFC/GC for the trace analysis of pesticide residues in fatty food samples

An on-line SFE-chromatographic system, where SFE has been coupled with SFC and GC, was developed and utilized for trace analyses of organochlorine and organophosphorus pesticide residues from gram-sized complex sample matrices, such as chicken fat, ground beef, and lard. The SFE process and chromatographic techniques were instrumentally integrated for efficient and automated on-line analysis, having minimal sample handling between the sample preparation and separation steps. A cleanup step, incorporating packed column SFC, allowed the fractionation of relatively small-sized, non-polar pesticides from the co-extracted fatty materials. This permitted final high-resolution separation of analytes on a capillary GC column. Detection of pesticides was accomplished using selective electron-capture and nitrogen-phosphorus detectors. Pesticide concentrations determined with the on-line system were accurate and reproducible, for fatty samples containing both fortified and incurred pesticides. This method, utilizing supercritical carbon dioxide, was considerably faster and less laborious than the conventional analytical procedures based on liquid extraction.     

Optimised accelerated solvent extraction of PCBs and PAHs from compost

This study is the first thorough method optimisation for accelerated solvent extraction (ASE) of polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs) from chemically dried compost. For PCBs, optimised solvent composition, temperature, pressure, number of static cycles, duration, and flush volume were as follows: toluene/acetone 1?:?3 (v/v), 120°C, 2000?psi, 3?×?5?min, and 50%, respectively. Limits of quantification and method precision were between 0.16 and 2.46?µg?kg^?1 dw and 6–17% respectively for individual PCBs. Absolute recoveries of isotope-labelled extraction standards used for each of the analytes ranged from 65 to 105% and relative recoveries were between 85 and 99%. The method proofed to be robust and was successfully applied to different compost samples.

The optimisation of PAHs extraction was performed and resulted in the following conditions: solvent: hexane/acetone 1/3 (v:v), temperature: 140°C, pressure: 1500?psi, extraction time: 3?×?5?min, and 50% flush volume. Limits of detection and method precision for individual PAHs were between 1.1 and 37.2?µg?kg^?1?dw and 12–34% respectively. Absolute and relative recoveries ranged from 24 to 68% and from 85 to 99%, respectively. Optimal extraction conditions for PAHs were more difficult to determine due to the inhomogeneous distribution of PAHs in samples. However, the method appeared to be feasible and suggestions for further improvements are presented.     

Pressurised liquid extraction of polycyclic aromatic hydrocarbons from gas and particulate phases of atmospheric samples

Pressurised liquid extraction (PLE) was applied to determine the atmospheric levels of 16 polycyclic aromatic hydrocarbons (PAHs) in the gas and particulate phases. The method involved high‐volume air sampling with quartz fibre filters (QFFs) and polyurethane foam (PUF) plugs and analytes were subsequently extracted from the samples by PLE, and determined with GC‐MS. We optimised the PLE conditions for the solvent, the number of cycles and extraction temperature. Recoveries were higher than 90% for most compounds. Method LODs and LOQs were between 0.001 and 0.02 ng/m³ and between 0.01 and 0.05 ng/m³. Air samples were taken from a site in the region of Tarragona in Catalonia, Spain, where one of the largest petrochemical complexes in southern Europe is located. The total concentration of PAHs were from 6.7 to 27.66 ng/m³, with predominant levels of PAHs appearing in the gas phase (48–81%), and an average level of benzo[a]pyrene, the most carcinogenic PAH, of 0.86 ng/m³.     

Direct determination of benzo[a]pyrene in water samples by a gold nanoparticle-based solid phase extraction method and laser-excited time-resolved Shpol'skii spectrometry

The strong affinity between polycyclic aromatic hydrocarbons (PAH) and the surface of gold colloids is investigated to device an extraction method for water samples. Within the 20-100 nm particle diameter range, the 20 nm gold nanoparticles showed the best extraction efficiencies for all the studied analytes. The new approach is combined to laser-excited time-resolved Shpol'skii spectrometry for the direct analysis of benzo[a]pyrene in drinking water samples. For a 500 μL sample volume, the analytical figures of merit demonstrate precise and accurate analysis at the parts-per-trillion level. The extraction efficiencies are statistically equivalent to 100% with relative standard deviations lower than 2%. The average recoveries were varied from 87.5% to 96.5% for different concentration of analytes. The simplicity of the experimental procedure, the low analysis cost, and the excellent analytical figures of merit demonstrate the potential of this approach for routine analysis of drinking water samples.     

Rotating-disk sorptive extraction of nonylphenol from water samples

In this study the sorption of nonylphenol was implemented on a rotating Teflon disk coated with a PDMS film on one of its surfaces. In this way, the disk, which has a high surface area, contacts only the liquid sample, which can be stirred at higher velocity than with the stir bar used in stir-bar sorptive extraction (SBSE), without damaging the phase while at the same time facilitating analyte mass transfer to the PDMS surface. We refer to the procedure as rotating-disk sorptive extraction (RDSE). Extraction variables such as disk rotational velocity, extraction time, and surface area of PDMS film were studied to establish the best conditions for extraction. With increasing rotational velocity, the amount of extracted analyte significantly increases because the stagnant layer concomitantly decreases. On the other hand, the extracted amount concomitantly increases with extraction time, reaching equilibrium at approximately 20 min, which can be reduced to 10 min when the surface area of PDMS increases from 1.74 to 6.97 cm². Precision of the method was determined by using the same disk (n = 6) and different disks (n = 3), showing relative standard deviations for the analyte of 3.7% and 10%, respectively. The detection limit of the method was 0.09 μg/L NP, defined at a signal to noise ratio of 3. The method was applied to a real sample, achieving quantitative recovery. The PDMS phase on the disk could be used for at least 50 experiments. In any case, replacement of the PDMS film on the disk is very easy and inexpensive, as compared to the commercial alternative SBSE.     

Effect of moisture on supercritical fluid extraction of polynuclear aromatic hydrocarbons and phenols from soil using an automated extractor

An automated supercritical fluid extraction system was evaluated with polynuclear aromatic hydrocarbons and phenols to demonstrate extraction efficiency, collection efficiency, and sample cross contamination. Results showed that 75/25 glass beads/octadecyl silica provided the highest collection efficiency for these classes of compounds. Also, the automated SFE system was used to study the effect of different percentages of water (w/w) in soil on extraction efficiency of fortified PAH and phenols at different temperatures and pressures. Results showed that the presence of (available) water in soil (>10%) does, increase extraction efficiency of higher molecular weight PAH at higher temperature. Also it was demonstrated that temperature rather than pressure had a marked effect on extraction efficiency. The extraction efficiency of phenols from soil which contained 5% of water, using pure supercritical CO₂, was higher than those obtained from dry soil or soil containing 1 % water. Extraction of phenols from soil did not show a dependence on pressure or temperature.     

Systematic study of the influence of modifiers on the CO2-supercritical extraction of PAHs in soil

Summary An exhaustive study of the behaviour in supercritical fluid extraction of eight PAHs in real samples of soil compared to spiked samples in silica has been carried out. The presence of a modifier is mandatory for quantitative extraction of the native analytes, but is unnecessary in spiked samples. The type and volume of modifier to be added and the sample-modifier contact time were optimized and the influence of the particle size assessed.