苯乙烯-马来酸酐共聚物增容Nylon-6/ABS共混体系的形态和力学性能

通过熔融共混法制备了苯乙烯-马来酸酐共聚物(SMA)增容的尼龙6(Nylon-6)/ABS共混物.采用TEM、SEM、FTIR等研究了SMA增容的Nylon-6/ABS共混物的相形态与性能.发现在Nylon-6和ABS的简单共混体系中,分散相易聚集,相界面清晰,断裂面光滑,呈脆性断裂,相容性差.加入少量SMA后,共混物由共连续相结构转变为典型的"海-岛"结构,分散相分布均匀,界面粘接程度增加,表明SMA对Nylon-6/ABS体系有显著的增容效果.     

Improvement of Impact Strength of Polylactide Blends with a Thermoplastic Elastomer Compatibilized with Biobased Maleinized Linseed Oil for Applications in Rigid Packaging

This research work reports the potential of maleinized linseed oil (MLO) as biobased compatibilizer in polylactide (PLA) and a thermoplastic elastomer, namely, polystyrene-b-(ethylene-ran-butylene)-b-styrene (SEBS) blends (PLA/SEBS), with improved impact strength for the packaging industry. The effects of MLO are compared with a conventional polystyrene-b-poly(ethylene-ran-butylene)-b-polystyrene-graft-maleic anhydride terpolymer (SEBS-g-MA) since it is widely used in these blends. Uncompatibilized and compatibilized PLA/SEBS blends can be manufactured by extrusion and then shaped into standard samples for further characterization by mechanical, thermal, morphological, dynamical-mechanical, wetting and colour standard tests. The obtained results indicate that the uncompatibilized PLA/SEBS blend containing 20 wt.% SEBS gives improved toughness (4.8 kJ/m²) compared to neat PLA (1.3 kJ/m²). Nevertheless, the same blend compatibilized with MLO leads to an increase in impact strength up to 6.1 kJ/m², thus giving evidence of the potential of MLO to compete with other petroleum-derived compatibilizers to obtain tough PLA formulations. MLO also provides increased ductile properties, since neat PLA is a brittle polymer with an elongation at break of 7.4%, while its blend with 20 wt.% SEBS and MLO as compatibilizer offers an elongation at break of 50.2%, much higher than that provided by typical SEBS-g-MA compatibilizer (10.1%). MLO provides a slight decrease (about 3 °C lower) in the glass transition temperature (T_g) of the PLA-rich phase, thus showing some plasticization effects. Although MLO addition leads to some yellowing due to its intrinsic yellow colour, this can contribute to serving as a UV light barrier with interesting applications in the packaging industry. Therefore, MLO represents a cost-effective and sustainable solution to the use of conventional petroleum-derived compatibilizers.     

Miscibility and compatibilization of poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene blends

Poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene (PTT/ABS) blends were prepared by melt processing with and without epoxy or styrene-butadiene-maleic anhydride copolymer (SBM) as a reactive compatibilizer. The miscibility and compatibilization of the PTT/ABS blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), capillary rheometer and scanning electron microscopy (SEM). The existence of two separate composition-dependent glass transition temperatures (T_gs) indicates that PTT is partially miscible with ABS over the entire composition range. In the presence of the compatibilizer, both the cold crystallization and glass transition temperatures of the PTT phase shifted to higher temperatures, indicating their compatibilization effects on the blends.The PTT/ABS blends exhibited typical pseudoplastic flow behavior. The rheological behavior of the epoxy compatibilized PTT/ABS blends showed an epoxy content-dependence. In contrast, when the SBM content was increased from 1 wt% to 5 wt%, the shear viscosities of the PTT/ABS blends increased and exhibited much clearer shear thinning behavior at higher shear rates. The SEM micrographs of the epoxy or SBM compatibilized PTT/ABS blends showed a finer morphology and better adhesion between the phases.     

PPO/SEBS-g-MAH共混体系的形态结构与冲击性能

从亚微相态和冲击性能出发 ,对比了采用熔融挤出法制备的PPO/SEBS和PPO/SEBS g MAH两种共混物 .结果表明 ,在本文所研究的弹性体用量范围内 ,PPO/SEBS为“海 岛”型结构 ,而PPO/SEBS g MAH呈现网状结构 ;PPO/SEBS体系无脆韧转变现象 ,PPO/SEBS g MAH体系则在弹性体用量为 10 %～ 15 %时出现明显的脆韧转变 ,缺口冲击强度达到 95 0J/m ,这种超韧现象源于其网状结构的形成 .文中进一步用DSC和毛细管流变仪对共混体系的热性能和流变性能进行了测试 ,探讨了PPO/SEBS g MAH共混物网状结构的形成原因     

Improvement in toughness of poly(l-lactide) (PLLA) through reactive blending with acrylonitrile-butadiene-styrene copolymer (ABS): Morphology and properties

Poly(l-lactide) (PLLA) was melt-blended with acrylonitrile-butadiene-styrene copolymer (ABS) with the aim of enhancing impact strength and elongation at break of PLLA, but not sacrificing its modulus and stiffness significantly. However, PLLA and ABS were found to be thermodynamically immiscible by simply melt blending and the formed blends show deteriorated mechanical properties. The reactive styrene/acrylonitrile/glycidyl methacrylate copolymer (SAN-GMA) by incorporating with ethyltriphenyl phosphonium bromide (ETPB) as the catalyst was used as the in situ compatibilizer for PLLA/ABS blends to improve the compatibility between PLLA and ABS. The reactive process during melt blending was investigated by Fourier transformed infra-red (FTIR). It showed that the epoxide group of SAN-GMA reacted with PLLA end groups under the mixing conditions and that the addition of ETPB accelerated the reaction. Phase structure and physical properties of the compatibilized blends were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), dynamic mechanical analysis (DMA), tensile tests and impact property measurements. It was found that the size of ABS domains in PLLA matrix is significantly decreased by addition of the reactive compatibilizer. The dynamic mechanical analysis revealed markedly shifted glass transition temperatures for both PLLA and ABS, indicating the improved compatibility between PLLA and ABS. The mechanical tests showed the compatibilized PLLA/ABS blends had a very nice stiffness-toughness balance, i.e., the improved impact strength and the elongation at break with a slightly loss in the modulus.     

Evaluation of the SEBS copolymer in the compatibility of PP/ABS blends through mechanical,thermal, thermomechanical properties,and morphology

Polypropylene (PP) blends with acrylonitrile-butadiene-styrene (ABS) were prepared using the styrene-ethylene-butylene-styrene copolymer (SEBS) as a compatibilizing agent. The blends were prepared in a co-rotational twin-screw extruder and injection molded. Torque rheometry, Izod impact strength, tensile strength, heat deflection temperature (HDT), differential scanning calorimetry, thermogravimetry, and scanning electron microscopy properties were investigated. The results showed that there was an increase in the torque of PA6/ABS blends with SEBS addition. The PP/ABS/SEBS (60/25/15%) blend showed significant improvement in impact strength, elongation at break, thermal stability, and HDT compared with neat PP. The elastic modulus and tensile strength have not been significantly reduced. The degree of crystallinity and the crystalline melting temperature increased, indicating a nucleating effect of ABS. The PP/ABS blends compatibilized with 12.5% and 15% SEBS presented morphology with well-distributed fine ABS particles with good interfacial adhesion. As a result, thermal stability has been improved over pure PP and the mechanical properties have been increased, especially impact strength. In general, the addition of the SEBS copolymer as the PP/ABS blend compatibilizer has the advantage of refining the blend's morphology, increasing its toughness and thermal stability, without jeopardizing other PP properties.     

Effects of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] on the charge distributions of low‐density polyethylene/polystyrene blends

The effect of the triblock copolymer poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) on the formation of the space charge of immiscible low‐density polyethylene (LDPE)/polystyrene (PS) blends was investigated. Blends of 70/30 (wt %) LDPE/PS were prepared through melt blending in an internal mixer at a blend temperature of 220 °C. The amount of charge that accumulated in the 70% LDPE/30% PS blends decreased when the SEBS content increased up to 10 wt %. For compatibilized and uncompatibilized blends, no significant change in the degree of crystallinity of LDPE in the blends was observed, and so the effect of crystallization on the space charge distribution could be excluded. Morphological observations showed that the addition of SEBS resulted in a domain size reduction of the dispersed PS phase and better interfacial adhesion between the LDPE and PS phases. The location of SEBS at a domain interface enabled charges to migrate from one phase to the other via the domain interface and, therefore, resulted in a significant decrease in the amount of space charge for the LDPE/PS blends with SEBS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2813–2820, 2004     

Phase behavior,crystallization, and nanostructures in thermoset blends of epoxy resin and amphiphilic star‐shaped block copolymers

This article reports thermoset blends of bisphenol A‐type epoxy resin (ER) and two amphiphilic four‐arm star‐shaped diblock copolymers based on hydrophilic poly(ethylene oxide) (PEO) and hydrophobic poly(propylene oxide) (PPO). 4,4′‐Methylenedianiline (MDA) was used as a curing agent. The first star‐shaped diblock copolymer with 70 wt % ethylene oxide (EO), denoted as (PPO‐PEO)₄, consists of four PPO‐PEO diblock arms with PPO blocks attached on an ethylenediamine core; the second one with 40 wt % EO, denoted as (PEO‐PPO)₄, contains four PEO‐PPO diblock arms with PEO blocks attached on an ethylenediamine core. The phase behavior, crystallization, and nanoscale structures were investigated by differential scanning calorimetry, transmission electron microscopy, and small‐angle X‐ray scattering. It was found that the MDA‐cured ER/(PPO‐PEO)₄ blends are not macroscopically phase‐separated over the entire blend composition range. There exist, however, two microphases in the ER/(PPO‐PEO)₄ blends. The PPO blocks form a separated microphase, whereas the ER and the PEO blocks, which are miscible, form another microphase. The ER/(PPO‐PEO)₄ blends show composition‐dependent nanostructures on the order of 10?30 nm. The 80/20 ER/(PPO‐PEO)₄ blend displays spherical PPO micelles uniformly dispersed in a continuous ER‐rich matrix. The 60/40 ER/(PPO‐PEO)₄ blend displays a combined morphology of worm‐like micelles and spherical micelles with characteristic of a bicontinuous microphase structure. Macroscopic phase separation took place in the MDA‐cured ER/(PEO‐PPO)₄ blends. The MDA‐cured ER/(PEO‐PPO)₄ blends with (PEO‐PPO)₄ content up to 50 wt % exhibit phase‐separated structures on the order of 0.5–1 μm. This can be considered to be due to the different EO content and block sequence of the (PEO‐PPO)₄ copolymer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 975–985, 2006     

Dependence of the interfacial reaction and morphology development on the functionality of the reactive precursors in reactive blending

PMMA containing 50 wt% of anthracene-labeled PMMA chains end-capped by a phthalic anhydride group (anth-PMMA-anh) has been melt blended at 180°C with PS containing 33 wt% of chains end-capped by an aliphatic primary amine (PS-NH₂) and PS bearing 3.5 pendant amine groups (as an average) along the chains (PS-co-PSNH₂), respectively. The reactive chains have been synthesized by atom transfer radical polymerization. Conversion of anth-PMMA-anh into PS-b-PMMA and PS-g-PMMA copolymers has been monitored by SEC with a UV detector. The interfacial reaction mainly occurs in the initial melting and softening stage (<1.0 min.), although at a rate which strongly depends on the number of reactive groups attached to PS chains, the higher conversion being observed for the PS-co-PSNH₂ containing blends. The phase morphology depends on the architecture of the in-situ formed copolymer. Indeed, a coarser phase dispersion is observed in case of the graft copolymer compared to the diblock.     

Weld line morphology and strength of polystyrene/polyamide-6/poly(styrene-co-maleic anhydride) blends

The effect of weld line on the morphology and mechanical properties of 70/30 polystyrene and polyamide-6 blends with various amounts of poly(styrene-co-maleic anhydride) (SMA) as compatibilizer was investigated. For blends without or with low content of SMA, the dispersed domains near the weld line were elongated parallel to the weld line; and the dispersed domains in weld line were spherical. But for blend with high content of SMA, the isotropic morphology was observed. And the difference of morphology at weld line caused the distinction of fracture mechanism. The tensile strength of the blend is greatly influenced by the morphology of dispersed domains at weld line. While the morphology has only slight effect on impact strength of the blends.     

异山梨醇型聚碳酸酯与ABS树脂共混体系的结构与性能研究

采用异山梨醇型聚碳酸酯(DB),与掺混型ABS熔融共混制备了具有不同聚丁二烯(PB)含量和丙烯腈(AN)含量的DB/掺混型ABS合金,并在考察掺混型ABS特征对合金结构与性能的影响的基础上,分别使用同种掺混型ABS以及各种商品化ABS树脂,比较了DB/ABS合金和双酚A型聚碳酸酯/ABS合金的性能及其变化规律.结果表明,对DB/掺混型ABS(70/30)合金而言,PB含量变化对于合金拉伸性能的影响明显大于AN含量变化所带来的影响,在PB含量为6.3 wt%条件下,各不同AN含量的合金体系均有最好的性能表现.PB含量和AN含量变化对合金分散相形态的影响与力学拉伸性能变化特征一致.DB/ABS合金体系均具有良好的热稳定性与热力学相容性,受AN含量和PB含量变化的影响较小,合金玻璃化转变温度与DB非常接近.以双酚A型聚碳酸酯为基础的聚碳酸酯(PC)/ABS合金及以异山梨醇型聚碳酸酯为基础的DB/ABS合金,在拉伸性能变化上均表现出完全相同的规律,且无论是采用掺混型ABS还是采用商品化ABS的体系,PC/ABS与DB/ABS合金在拉伸性能所反映出的规律也是基本一致的.     

Synthesis of a random copolymer and its compatibility for thermotropic liquid crystalline polymer/poly(ether ether ketone) blends

A random copolymer (RCP) containing poly(ether ether ketone) (PEEK) and thermotropic liquid crystalline polymer (TLCP) segments was synthesized. Its chemical structure and liquid crystalline properties were characterized by FT‐IR, differential scanning calorimetry (DSC) and polar light microscopy (PLM) respectively. A single glass transition temperature (T_g) at 134.0°C, a melting temperature (T_m) at 282.0°C and a temperature of ignition (T_i) at 331.3°C can be observed. Blends of PEEK and TLCP with and without RCP as compatibilizer were prepared by extrusion and the effect of RCP on the thermal properties, dynamic mechanical properties, morphology and static tensile mechanical properties of blends was investigated by means of DSC, dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), etc. Dynamic mechanical measurements indicated that there appeared to be only a single tan δ peak resulting from the glass transition of the PEEK‐rich phase and the T_g value shifted towards higher temperature due to the presence of compatibilizer, as suggested partial compatibility. Morphological investigations showed that the addition of RCP to binary blends reduced the dispersed phase size and improved the interfacial adhesion between the two phases. The ternary compatibilized blends showed enhanced tensile modulus compared to their binary blends without RCP. The strain at break decreased for the ternary blends due to embrittlement of the matrix by the incorporation of some RCP to the matrix phase. Copyright © 2007 John Wiley & Sons, Ltd.     

Supertoughness and critical interparticle distance dependence in poly(butylene terephthalate) and poly(ethylene‐co‐glycidyl methacrylate) blends

Supertough poly(butylene terephthalate) (PBT)‐based blends were obtained by the melt blending of PBT with 0–30 wt % poly(ethylene‐co‐glycidyl methacrylate) (EGMA). The reaction between PBT and EGMA was detected by torque measurements. The particle size was almost constant with increasing EGMA content, and this indicated that compatibilization occurred. The minimum EGMA content for achieving supertoughness (i.e., an impact strength 16 times greater than that of PBT) was 20 wt %. The interparticle distance was the parameter controlling toughness in these PBT/EGMA blends. The dependence of the critical interparticle distance (τ_c) on the modulus of the dispersed phase appeared only at low τ_c values, and the primary dependence of τ_c on the ratio of the modulus of the matrix to the modulus of the rubbery dispersed phase was proposed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2236–2247, 2003     

Effect of pressure on phase behavior in polymer blends of poly(2,6-dimethyl-1,4-phenylene oxide) and poly(styrene-co-p-fluorostyrene) copolymers

The effect of pressure on the miscibility of blends of poly(2,6-dimethyl-l,4-phenylene oxide) (PPO) with a random copolymer of styrene and para-fluorostyrene, P(S-co-p-FS), has been studied by high pressure differential thermal analysis (HPDTA). P(S-co-p-FS) copolymers less than 36 mole % p-FS are miscible with PPO in all proportions irrespective of pressure up to 200 MPa, using the customary criterion of a single calorimetric glass relaxation. P(S-co-p-FS) copolymers containing 40 to 50 mole % p-FS undergo phase separation upon annealing at elevated temperatures, indicating the existence of a lower critical solution temperature (LCST). In these blends, pressure displaces the phase boundary associated with the LCST to higher temperatures causing an apparent increase in polymer miscibility. The phase diagram for the blend of PPO and P(S-co-p-FS) containing 46 mole % p-FS, shows that the critical composition at about 50 wt % PPO does not change with pressure, but the consolute temperature T_c increases with increasing pressure. The pressure dependence of the LCST (dT_c/dP) of this system is about 0.35°C/MPa.     

Viscoelastic interfacial properties of compatibilized poly(ε‐caprolactone)/polylactide blend

Poly(ε‐caprolactone)/polylactide blend (PCL/PLA) is an interesting biomaterial because the two component polymers show good complementarity in their physical properties. However, PCL and PLA are incompatible thermodynamically and hence the interfacial properties act as the important roles controlling the final properties of their blends. Thus, in this work, the PCL/PLA blends were prepared by melt mixing using the block copolymers as compatibilizer for the studies of interfacial properties. Several rheological methods and viscoelastic models were used to establish the relations between improved phase morphologies and interfacial properties. The results show that the interfacial behaviors of the PCL/PLA blends highly depend on the interface‐located copolymers. The presence of copolymers reduces the interfacial tension and emulsified the phase interface, leading to stabilization of the interface and retarding both the shape relaxation and the elastic interface relaxation. As a result, besides the relaxation of matrices (τ_m) and the shape relaxation of the dispersed PLA phase (τ_F), a new relaxation behavior (τ_β), which is attribute to the relaxation of Marangoni stresses tangential to the interface between dispersed PLA phase and matrix PCL, is observed on the compatibilized blends. In contrast to that of the diblock copolymers, the triblock copolymers show higher emulsifying level. However, both can improve the overall interfacial properties and enhance the mechanical strength of the PCL/PLA blends as a result. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 756–765, 2010     

ABS的MAH/St多单体熔融接枝及其对PA6/ABS共混体系相形态和力学性能的影响

通过多单体熔融接枝的方法制备出了具有较高接枝率的ABS接枝物 (ABS g (MAH co St) ) ,并对其接枝机理进行了初步探讨 .研究表明 ,MAH、St接枝ABS时 ,反应主要发生在ABS中聚丁二烯的双键部位 .同时 ,当MAH与St的用量比约为 1:1时接枝率达到最高 .ABS g (MAH co St)作为尼龙 6 (PA6 ) ABS共混体系相容剂起到了良好的增容效果 .实验证明 ,相容剂使用前后 ,共混物的相区尺寸由几十 μm减小到 1μm以下 ,且分布更加均匀 ;共混物的拉伸强度和冲击强度等力学性能也同时得到均衡改善 .     

SMA、OMMT对PA6/ABS共混物聚集态结构及性能影响的研究

采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射(XRD)等手段研究了苯乙烯-马来酸酐共聚物(SMA)、有机蒙脱土(OMMT)对尼龙6(PA6)/丙烯腈-丁二烯-苯乙烯(ABS)共混物体系聚集态结构及性能的影响.结果表明,SMA与OMMT的加入均可提高PA6/ABS共混物体系的强度及模量,但加入OMMT后共混物的韧性有所下降,而PA6/ABS/SMA共混物的韧性随SMA含量的增加呈上升趋势.SMA、OMMT对PA6/ABS共混体系都有细化ABS分散相的作用,随SMA加入量的增加,ABS分散相尺寸逐渐减小,分布趋于均匀;当OMMT加入量在4 phr以内时,对ABS分散相粒径影响不大,超过4 phr后,随着OMMT含量的增加,ABS分散相的尺寸逐渐减小.XRD与TEM的分析结果表明,对PA6/OMMT(100/5)共混物,OMMT主要以剥离形态分布,同时也存在少量OMMT聚集体;PA6/ABS/OMMT共混物中OMMT则基本以剥离形态选择分布在PA6基体相中.     

Effect of PEO‐PPO‐PEO copolymer on the mechanical and thermal properties and morphological behavior of biodegradable poly (L‐lactic acid) (PLLA) and poly (butylene succinate‐co‐L‐lactate) (PBSL) blends

A blend of two biodegradable and semi‐crystalline polymers, poly (L‐lactic acid) (PLLA; 70 wt%) and poly (butylene succinate‐co‐L‐lactate) (PBSL; 30 wt%), was prepared in the presence of various polyethylene oxide‐polypropylene oxide‐polyethylene oxide (PEO‐PPO‐PEO) triblock copolymer contents (0.5, 1, 2 wt%). Mechanical, thermal properties, and Fourier transform infrared (FTIR) analysis of the blends were investigated. It was found that the addition of copolymer to PLLA/PBSL improved the fracture toughness of the blends as shown by mode I fracture energies. It was supported by morphological analysis where the brittle deformation behavior of PLLA changed to ductile deformation with the presence of elongated fibril structure in the blend with copolymer system. The glass transition temperature (T_g), melting temperature (T_m) of PLLA, and PBSL shift‐closed together indicated that some compatibility exists in the blends. In short, PEO‐PPO‐PEO could be used as compatibilizer to improve the toughness and compatibility of the PLLA/PBSL blends. Copyright © 2010 John Wiley & Sons, Ltd.     

Thermal behaviors and characteristics of polylactide/poly(butylene succinate) blend films via reactive compatibilization and plasticization

Polylactide (PLA)/poly(butylene succinate) (PBS) blend films modified with a compatibilizer and a plasticizer were hot‐melted through a twin screw extruder and prepared by hydraulic press. Toluene diisocyanate (TDI) and polylactide‐grafted‐maleic anhydride (PLA‐g‐MA) were used as compatibilizers, while triethyl citrate and tricresyl phosphate acted as plasticizers. The effects of the type and content of compatibilizer and plasticizer on the mechanical characteristics, thermal properties, crystallization behavior, and phase morphology of the PLA/PBS blend films were investigated. Reactive compatibilization at increasing levels of TDI improved the compatibility of the PLA and PBS, affecting the toughness of the films. As evidenced by scanning electron microscope, the addition of TDI enhanced the interfacial adhesion of the blends, leading to the appearance of many elongated fibrils at the fracture surface. Furthermore, PLA/PBS blending with both TDI and PLA‐g‐MA led to an acceleration of the cold crystallization rate and an increment of the degree of crystallinity ( ). Toluene diisocyanate could be a more effective compatibilizer than PLA‐g‐MA for PLA/PBS blend films. The synergistic combination of compatibilizer and plasticizer brought a significant improvement in elongation at break and tensile‐impact toughness of the PLA/PBS blends, compared with neat PLA. Their failure mode changed from brittle to ductile due to the improved compatibility and molecular segment mobility of the PLA and PBS phases. Differential scanning calorimeter results revealed that the plasticizers triethyl citrate and tricresyl phosphate changed the thermal behavior of T_cc and T_m, affecting α′ and α crystal formations. However, these plasticizers only slightly improved the thermal stability of the films.     

THE EFFECT OF BLENDING SEQUENCE ON PHASE MORPHOLOGY OF NYLON 6/ABS/SMA BLENDS

The preparation process-dependent phase morphology of blends composed of nylon 6 and acrylonitrile-butadiene- styrene(ABS)over a composition range of 30-70 wt% using a styrene-maleic anhydride(SMA)copolymer as the compatibilizing agent with a constant content(5phr)was investigated.The results of the scanning electron microscope (SEM)observation revealed that compared with the binary blends of nylon 6 and ABS,the existence of SMA caused a composition shift of phase inversion to a higher weight fraction of...