Phenylethynyl-pendant polyphenylquinoxalines curable by an intramolecular cycloaddition reaction

Polyphenylquinoxalines containing 2,2′-bis(phenylethynyl)diphenylene moieties along the polymer backbone have been synthesized. As anticipated, these polymers were found to undergo a novel curing reaction consisting of an intramolecular cycloaddition (IMC) of pendant groups to a dibenzoanthracene backbone structure. The IMC reduces chain mobility, and the fused ring structure increases the glass transition temperature of the polymer. The potential of this approach to curing high-temperature polymers was demonstrated in the processing of one such polymer having an initial T_g of 215°C. Curing at 245°C with no evolution of volatiles produced a T_g of 365°C. This very significant increase in potential use temperature via a volatiles-free IMC cure provides promise for a tough phenyiquinoxaline resin system which can be used to fabricate reinforced composites that have use temperatures far exceeding processing temperatures.     

The design,synthesis, and nonlinear optical properties of novel X‐type polyurethane containing dicyanovinylnitroresorcinoxy group with enhanced SHG thermal stability

Novel X‐type polyurethane 5 containing 4‐(2′,2′‐dicyanovinyl)‐6‐nitroresorcinoxy groups as nonlinear optical (NLO) chromophores, which constitute parts of the polymer backbone, was prepared and characterized. Polyurethane 5 is soluble in common organic solvents such as acetone and N,N‐dimethylformamide. It shows thermal stability up to 280 °C from thermogravimetric analysis with a glass transition temperature (T_g) obtained from differential scanning calorimetry thermogram of around 120 °C. The second harmonic generation (SHG) coefficient (d₃₃) of poled polymer film at 1064‐nm fundamental wavelength is around 6.12 × 10^?9 esu. The dipole alignment exhibits a thermal stability even at 5 °C higher than T_g, and there was no SHG decay below 125 °C due to the partial main chain character of the polymer structure, which is acceptable for NLO device applications. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Aqueous solution behavior of comb‐shaped poly(2‐ethyl‐2‐oxazoline)

A series of comb polymers consisting of a methacrylate backbone and poly(2‐ethyl‐2‐oxazoline) (PEtOx) side chains was synthesized by a combination of cationic ring‐opening polymerization and reversible addition–fragmentation chain transfer polymerization. Small‐angle neutron scattering (SANS) studies revealed a transition from an ellipsoidal to a cylindrical conformation in D₂O around a backbone degree of polymerization of 30. Comb‐shaped PEtOx has lowered T_g values but a similar elution behavior in liquid chromatography under critical conditions in comparison to its linear analog was observed. The lower critical solution temperature behavior of the polymers was investigated by turbidimetry, dynamic light scattering, transmission electron microscopy, and SANS revealing decreasing T_cp in aqueous solution with increasing molar mass, the presence of very few aggregated structures below T_cp, a contraction of the macromolecules at temperatures 5 °C above T_cp but no severe conformational change of the cylindrical structure. In addition, the phase diagram including cloud point and coexistence curve was developed showing an LCST of 75 °C of the binary mixture poly[oligo(2‐ethyl‐2‐oxazoline)methacrylate]/water. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Semicrystalline poly(vinyl ether)s with high and phototunable glass transition temperature: application for thermally stable and reworkable adhesives

The photoinduced solid–liquid phase transition of azobenzene-based polymers is an attractive method to synthesize stimuli-responsive functional materials. As the structure–property relationships of such materials are not fully understood, a new class of polymer backbone, that is, poly(vinyl ether) (PVE), was studied for the development of azobenzene-based polymers with high thermal stability. For this purpose, a series of azobenzene-based PVEs with different monomer structures were synthesized using a Lewis acid catalyst-based cationic polymerization method. Typical PVEs are viscous polymers with low glass-transition temperatures (T_g's). The flexibility of the polymer backbone improves with the use of alkylene spacers, changing the order of alignment of the mesogenic azobenzene moieties attached to the backbone, leading to high T_g's of the azobenzene-based PVEs. One of the synthesized PVEs shows a high glass-transition temperature of 94 °C, which is 14 °C higher compared to that of the corresponding polymethacrylate. Furthermore, the PVE exhibits photoinduced solid–liquid phase transition from the semicrystalline state. This phase transition material, with its high thermal stability, has the potential for broader applications, such as for the phototuning of adhesion. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 568–577     

Synthesis and nonlinear optical properties of novel Y‐type polyurethane containing tricyanovinylthiazole with enhanced thermal stability of second harmonic generation

A novel Y‐type poly[iminocarbonyloxyethyl‐5‐methyl‐4‐{2‐thiazolylazo‐4‐(1,2,2‐tricyanovinyl)}resorcinoxyethyloxycarbonylimino‐(3,3′‐dimethoxy‐4,4′‐biphenylene)] 4 containing 5‐methyl‐4‐{5‐(1,2,2‐tricyanovinyl)‐2‐thiazolylazo}resorcinoxy groups as nonlinear optical (NLO) chromophores, which constitute part of the polymer backbone, was prepared and characterized. Polyurethane 4 is soluble in common organic solvents such as acetone and N,N‐dimethylformamide. It showed a thermal stability up to 250 °C in thermogravimetric analysis thermogram and the glass‐transition temperature (T_g) obtained from differential scanning calorimetry thermogram was around 118 °C. The second harmonic generation coefficient (d₃₃) of poled polymer films at 1560 nm fundamental wavelength was around 8.43 × 10^?9 esu. The dipole alignment exhibited a thermal stability even at 12 °C higher than T_g, and there was no SHG decay below 130 °C due to the partial main‐chain character of the polymer structure, which is acceptable for NLO device applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1166–1172, 2010     

Synthesis,characterization, and thermal properties of ring‐opening metathesis polynorbornenes and their hydrogenated derivatives bearing various ester and cyano groups

Doubly functionalized polar norbornenes 3a – 3g substituted by both a variety of ester and cyano groups were polymerized by ring‐opening metathesis polymerization (ROMP) with a Ru carbene complex 2 bearing 3‐bromopyridine as a ligand (third generation Grubbs' catalyst) in a living manner. The successive hydrogenation of the main‐chain double bond in the synthesized living ROMP polymers 4a – 4g with a hydridoruthenium complex was exploited. The comparison of thermal properties of a series of ring‐opening metathesis polymers 4a – 4g with those of their hydrogenated derivatives 5a – 5g revealed the decrease of glass transition temperatures (T_g) but little change of the 5% decomposition temperature (T_d⁵). In all cases examined in this study, a decrease of T_g by hydrogenation was around 20–40 °C, regardless of the ester substitutents. In the presence of the additional PCy₃, triethylamine, and methanol after complete consumption of monomer 3a under the living ROMP condition, the tandem ROMP‐hydrogenation of the resulting polymer 4a generated in situ was attained under a H₂ (9.8 MPa) atmosphere at 80 °C to afford the hydrogenated polymer 5a , retaining the narrow polydispersity of 1.03. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3314–3325 2008     

Glass transition temperatures of several fluorine-containing polymers

The glass transition temperatures T_g of several fluorine-containing polymers were determined by use of the differential scanning calorimeter. Values between ?3 and 230°C were obtained. In polymers of α-olefins, T_g increases with the fluorine content of the backbone and the length of the n-perfluoroalkyl branch. In styrene polymers T_g also is higher if the backbone contains fluorine but nearly the same T_g's are found for polymers with phenyl and pentafluorophenyl groups. Saturated polymers of perfluoro-α,ω-dienes have lower T_g's than polyperfluoro-α-olefins. The T_g's of chloroperfluoropolymers are higher than those of perfluoropolymers. Polyperfluoropentadiene-1,3 has the lowest T_g of the polymers examined. Polyperfluoropentadiene-1,3 forms by 1,4-addition.     

Consequences of the ‘jacketed’ effect on mesomorphic and orientational properties of ‘side-on fixed’ liquid crystalline polymers

Abstract

The mesomorphic properties have been studied as a function of the degree of polymerization for certain ‘side-on fixed’ polyacrylates. A peculiar evolution of the clearing temperature, T _IN, as well as of the glass transition temperatures, T _g, revealed that beyond a certain backbone length, T _IN and T _g decrease as the main chain length increases. The nematic ‘jacketed’ structure of these polymers induces a more or less high anisotropy of the polymer backbone conformation in the nematic phase and this can counterbalance the usual effect of an increase in the degree of polymerization on the thermodynamical properties of these systems. This evolution allows us to explain the unusual diamagnetic anisotropy anomaly observed as a function of temperature for this type of polymer.     

NOTE: Synthesis and Characterization of a Poly(acrylamide) with Pendant 1,4-piperazine-2,5-dione Moieties via Post-polymerization Cyclization

A poly(acrylamide) was synthesized from N ^α -Boc-N ^? -acrolyl-l-lysylglycine methyl ester via radical polymerization. This polymer typically had Mn ～ 100,000 g/mol, Mw ～ 300,000 g/mol, and a T_g of 93°C. Removal of Boc with TFA and cyclization with DABCO? in DMSO at 65°C afforded a soluble piperazinedione-containing polymer that had a T_g of 157°C and thermal stability up to 300°C. These results demonstrate a viable and efficient synthetic route to piperazinedione-containing polyacrylamides of high molecular weight. Related polymers that incorporate substituted indane moieties could be useful high T_g materials for fabrication of LC and NLO devices.     

Thiol–norbornene materials: Approaches to develop high Tg thiol–ene polymers

The ability to prepare high T_g low shrinkage thiol–ene materials is attractive for applications such as coatings and dental restoratives. However, thiol and nonacrylated vinyl materials typically consist of a flexible backbone, limiting the utility of these polymers. Hence, it is of importance to synthesize and investigate thiol and vinyl materials of varying backbone chemistry and stiffness. Here, we investigate the effect of backbone chemistry and functionality of norbornene resins on polymerization kinetics and glass transition temperature (T_g) for several thiol–norbornene materials. Results indicate that T_gs as high as 94 °C are achievable in thiol–norbornene resins of appropriately controlled chemistry. Furthermore, both the backbone chemistry and the norbornene moiety are important factors in the development of high T_g materials. In particular, as much as a 70 °C increase in T_g was observed in a norbornene–thiol specimen when compared with a sample prepared using allyl ether monomer of analogous backbone chemistry. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5686–5696, 2007     

Demonstration of isospecific free radical polymerization of acrylate controlled by conformation and chirality of monomer

Radical polymerization of lactic acid‐based chiral and achiral methylene dioxolanones, a model for conformationally s‐cis locked acrylate, was carried out with AIBN to demonstrate an isospecific free radical polymerization controlled by chirality and conformation of monomer. Polymerization of the dioxolanones proceeded smoothly without ring opening to give a polymer with moderate molecular weight and 100% of maximum isotacticity. ESR spectrum indicated a twisted conformation of the growing poly(methylene dioxolanone) radical in contrast to an acyclic analogous radical, suggesting a restriction of the free rotation around main chain C_α? C_β bond of the growing radical center. Chirality as well as the polarity and bulkiness of monomer affected the polymer tacticity, and chiral alkyl substituent would afford a high isotactic polymer, in which higher the enantiomeric excess of the monomer was, higher the isotacticity of the polymer was. While, achiral or polar substituents including dibenzyl and trichloromethyl groups would afford an atactic polymer. In addition, glass transition temperature (T_g) of the resulting polymers was significantly high, ranging from 172.2 to 229.8 °C, and even for an isotactic polymer T_g was as high as 206.8 °C. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2007–2016     

Synthesis and characterization of soluble polyimides derived from [1,1′;4′,1″]terphenyl‐2′,5′‐diol and biphenyl‐2,5‐diol

Two series of polyimides based on laterally attached p‐terphenyl and biphenyl groups were synthesized. The solubility and thermal properties were studied using DSC, thermogravimetric analysis, and the solubility test. These polymers exhibited good thermal stability and excellent solubility. The high solubility for both polymer series was attributed to the non‐coplanarity of diamine monomers and the use of fluorinated dianhydride, whereas the slightly better solubility for polymers based on p‐terphenyl was attributed to further weakening of interchain interaction of the polymers. Both polymer series exhibited glass‐transition temperatures (T_g's) in the range of 244–272 °C. The T_g's of polymers containing laterally attached p‐terphenyls were higher than those of their counterparts containing biphenyls by 5–17 °C. This was attributed to the formation of an interdigitated structure that hinders the segmental movement of polymer chains. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2998–3007, 2001     

Preparation of HPEEK by Oligomer A2+B3 Approach

A series of hyperbranched poly(ether ether ketones) with different chain length between branching point (L) were prepared using a A₂+B₃ methodology, in which the A₂ is hydroxyl‐terminated PEEK oligomer. The L affects the properties of the polymers such as the inherent viscosity, the degree of crystallinity, the thermal properties of the polymers etc. The polymer with a L₂≈8 had T _g (122.4°C), T _c (200.2°C), and broad T _m (247.4°C). With the increment of L, up to the point L₂≈20 and L₂≈35, the polymers become semi‐crystalline, with a melting point of 300.9°C and 317.9°C, respectively. Their wide angle X‐ray scattering (WAXS) pattern indicated that their crystal structure is exactly the same as that of the linear homopolymer.     

Synthesis and characterization of new poly(arylene ether)s containing heterocyclic units. II.

A series of new poly(arylene ether)s, containing naphthalene, pyridine, and quinoline units have been prepared by solution condensation polymerization. The synthesis involves nucleophilic displacement of aromatic dihalides with aromatic potassium bisphenates in an anhydrous dipolar aprotic solvent at elevated temperatures. The polymers, having inherent viscosity from 0.24 to 1.32 dL/g, were obtained in quantitative yield, have excellent thermal stability as shown by 10% weight loss temperatures in nitrogen and air (above 450 and 430°C, respectively) and high glass transition temperatures (in the range of 150–220°C). The introduction of quinoline moieties in the polymer backbone positively influences the thermal properties, such as high T_g/T_m ratios. © 1995 John Wiley & Sons, Inc.     

Blending to Make Nonhealable Polymers Healable: Nanophase Separation Observed by CP/MAS 13C NMR Analysis

Can commodity polymers are made to be healable just by blending with self-healable polymers? Here we report the first study on the fundamental aspect of this practically challenging issue. Poly(ether thiourea) (PTUEG₃; T_g=27 °C) reported in 2018 is extraordinary in that it is mechanically robust but can self-heal even at 12 °C. In contrast, poly(octamethylene thiourea) (PTUC₈; T_g=50 °C), an analogue of PTUEG₃, cannot heal below 92 °C. We found that their polymer blend self-healed in a temperature range above 32 °C even when its PTUEG₃ content was only 20 mol %. Unlike PTUEG₃ alone, this polymer blend, upon exposure to high humidity, barely plasticized, keeping its excellent mechanical properties due to the non-hygroscopic nature of the PTUC₈ component. CP/MAS ¹³C NMR analysis revealed that the polymer blend was nanophase-separated, which possibly accounts for why such a small amount of PTUEG₃ provided the polymer blend with humidity-tolerant self-healable properties.     

Enhanced Temporal Stability of an NLO Polyurethane via a Two‐Dimensional Chromophore

A new NLO‐active polyurethane (T_g = 145°C) based on a two‐dimensional NLO chromophore has been investigated. Two ends of this lambda‐shaped chromophore can be directly bound to the main chain of polyurethane. After poling, fast relaxation of the effective second harmonic (SH) coefficient was observed at temperatures higher than 122°C. Moreover, excellent temporal stability at 100°C was obtained despite the operating temperature being very close to the fast relaxation temperature. This is due to the fact that embedding the rigid lambda‐shaped chromophores into the polymer backbone effectively restricts molecular motion at temperatures close to T_g.     

Synthesis,Characterization, and Functionalization of Hyperbranched Poly(ether ether ketone)s with Phenoxypheyl Side Group

Novel fluoride‐teminated hyperbranched poly(ether ether ketone) with 4‐phenoxyphenyl side group (HPEEK‐F) was prepared from 2‐(4‐phenoxyphenyl)‐1,4‐diphenol (A₂) and 1,3,5‐tris[4‐(4‐flourobenzoyl) phenoxy]benzene (B₃). An end‐capping approach was used to synthesize tertiary amino‐terminated fluorescent (HPEEK‐DMA) and phenyl ethynyl‐terminated self‐crosslinking poly(ether ether ketone)s (HPEEK‐PEP). These three polymers have the same backbone structure and degree of branching (DB=0.67), and different terminal groups. The nature of the terminal group was shown as the influences of the glass transition temperature (T_g) and decomposition temperature (T_d) of polymers. The T_g of HPEEK‐F and HPEEK‐DMA are 30°C lower than HPEEK‐PEP, whereas the T_d of HPEEK‐F are 90°C and 50°C higher than HPEEK‐DMA and HPEEK‐PEP, respectively. The HPEEK‐DMA fluoresce blue‐green in solid and in solution. This kind of hyperbranched polymer contains a large amount of terminal chromophore groups which can easily lead to the formation of intramolecular excimers. The fluorescence signal was decreased with increasing acidity, furthermore, the two peaks at 466 nm and 507 nm indicated a blue shift occurred. After curing, the HPEEK‐PEP displayed a T_g at 235.5°C, which is 100°C higher than original polymers. Thermally cured samples show good anti‐chemical corrodibility in DMF, THF, DMAc and NMP solvents.     

Determination of ultra-low glass transition temperature via differential scanning calorimetry

A novel method was developed to determine the ultra-low glass transition temperature (T_g) of materials through physical blending via differential scanning calorimetry. According to the Fox equation for polymer blends, a blend of two fully compatible polymers has only one T_g. The single T_g is a function of the T_gs of the two simple polymers. Thus, the ultra-low T_g of one material can be obtained from the T_gs of another polymer and their blends. The error of T_g measurements depends on the measurement error of the T_gs for the blends and another polymer. The method was successfully applied to determine the T_gs of acetyl tributyl citrate (ATBC), tributyl citrate (TBC) and poly(ethylene glycol)s (PEG)s with different molecular weights. The T_gs for ATBC, TBC, PEG-4000 and PEG-800 were ?57.0 °C, ?62.7 °C, ?76.6 °C and ?83.1 °C, respectively. For all the samples, the standard deviation of measurements was less than 3.3 °C, and the absolute error of measurements was theoretically not more than 5.3 °C. These results indicate that this method has acceptable precision and accuracy.     

Polymerization of N-(p-aminobenzoyl)caprolactam: Block and alternating copolymers of aromatic and aliphatic polyamides

The polymerization behavior of N-(p-aminobenzoyl)caprolactam was studied. It was found that polymerization could proceed by either elimination of caprolactam or by ring opening. Polymers prepared at temperatures above 200°C showed a greater tendency for ring opening to produce alternating aromatic/aliphatic copolymers than did polymers prepared at lower temperatures. Block copolymers of poly(p-benzamide) and nylon 6 were prepared by a two-stage hydrolytic polymerization process or by anionic polymerization at temperatures > 200°C. Polymer microstructures were determined using ¹³C-NMR spectroscopy by comparison with homopolymers and model alternating copolymers. The alternating copolymer prepared by condensation of N-(p-aminobenzoyl)-6-caproic acid showed a melting transition at 300–305°C in the DSC and a T_g in subsequent heating cycles of 116–119°C. Copolymers made with the two-stage process were rich in p-benzamide sequences and showed no T_g or T_m below 400°C. Copolymer made with NaH was rich in nylon 6 units, showed a T_m of 175–180°C and a T_g of 80–81°C, and was homogeneous in both the melt and solid.     

Free volumes in nematic and smectic liquid-crystalline polymers probed by positron annihilation

Free volumes in thermotropic side-chain liquid-crystalline polymers were probed by positron annihilation technique. Lifetime spectra of positrons were measured in the temperature range between 130 and −60°C in cooling. For a nematic liquid-crystalline polymer (polyacrylate), the lifetime of ortho-positronium (τ₃) was decreased with decreasing temperature above the glass transition temperature (T_g, 21°C) with larger temperature coefficient than that below T_g. The intensity of ortho-positronium (I₃) was constant above T_g. These facts mean that the size of the free-volume holes decreased with the decreasing the temperature but the concentration was almost constant in nematic phase. For a smectic liquid-crystalline polymer (poly(p-methylstyrene) derivative), a discontinuous decrease in the value of τ₃ and that of I₃ were observed at 107°C, which was the transition temperature from smectic to crystalline phase. Such discontinuous changes were not observed for the polyacrylate specimen. This difference was considered to be attributed to the higher-ordered structure of the smectic phase. © 1996 John Wiley & Sons, Inc.