Determination and fractionation of sulphur in a contaminated dredged sediment

Conversion of sulphur compounds in reduced, contaminated sediments that are brought in upland conditions may largely affect the potential mobility of heavy metal contaminants. We applied selected methods for the determination of total sulphur and sulphur fractions in a contaminated sediment in the reduced state and after gradual drying and oxidation during 1 month. Dry ashing, followed by ion chromatographic detection, was reliable for the determination of total sulphur. Good recoveries were obtained in both reference samples and spiked samples. Total sulphur was 14.5±0.6 g kg⁻¹ relative to dry sediment. Wet chemical methods that involve the determination of acid-volatile, Zn–HCl-reducible, chromium-reducible, acetone-soluble and HI-reducible sulphur were used to estimate specific sulphur forms. Results for acetone-soluble sulphur were to high and not consistent with results for other fractions. Major part of sulphur in the sediment (90%) was inorganic. Sulphides were converted partially to sulphate and to intermediary oxidised sulphur compounds upon oxidation of the sediment. The results suggested that the intermediary oxidised sulphur pool in the reduced sediment (2.5 g kg⁻¹) mainly consisted of pyrite, that was not converted during drying and oxidation. No significant changes in organic sulphur were detected.     

Occurrence of residual water within disk-based solid-phase extraction and its effect on GC-MS measurement of organic extracts of environmental samples

Solid-phase extraction (SPE) is a widespread and powerful sample preparation technique in many analytical areas. Many of the used methods reduce residual water during sample preparation by drying the phase material. Despite the importance of this step, hardly any study deals specifically with the drying process, and if so, only few aspects are mentioned. The present study is the first systematic investigation of the drying process using SPE disks, including the influence of process parameters on the amount of residual water and its consequences for subsequent elution and gas chromatography-mass spectrometry (GC-MS) analysis. The following points were investigated in detail: (1) the change of pressure and volume flow during the drying process, (2) the remaining amount of water at different drying times for different SPE materials, (3) the influence of suspended particulate matter on the drying process and (4) the effects of the residual water on the elution step by using different organic solvents. The study shows that the volume of residual water in the SPE disk is affected by the fixation of the sorbent, the phase material, the amount of sorbent, the pumping settings and the duration of the drying process. Furthermore, systematic investigations demonstrate the influence of residual water on the GC-MS analysis and show analytical interferences only for a few of the investigated analytes. All results suggest that more problems in SPE GC-MS methods are caused by residual water than previously assumed.     

Determination and fractionation of sulphur in a contaminated dredged sediment

Conversion of sulphur compounds in reduced, contaminated sediments that are brought in upland conditions may largely affect the potential mobility of heavy metal contaminants. We applied selected methods for the determination of total sulphur and sulphur fractions in a contaminated sediment in the reduced state and after gradual drying and oxidation during 1 month. Dry ashing, followed by ion chromatographic detection, was reliable for the determination of total sulphur. Good recoveries were obtained in both reference samples and spiked samples. Total sulphur was 14.5±0.6 g kg⁻¹ relative to dry sediment. Wet chemical methods that involve the determination of acid-volatile, Zn–HCl-reducible, chromium-reducible, acetone-soluble and HI-reducible sulphur were used to estimate specific sulphur forms. Results for acetone-soluble sulphur were to high and not consistent with results for other fractions. Major part of sulphur in the sediment (90%) was inorganic. Sulphides were converted partially to sulphate and to intermediary oxidised sulphur compounds upon oxidation of the sediment. The results suggested that the intermediary oxidised sulphur pool in the reduced sediment (2.5 g kg⁻¹) mainly consisted of pyrite, that was not converted during drying and oxidation. No significant changes in organic sulphur were detected.     

Determination of 39 polybrominated diphenyl ether congeners in sediment samples using fast selective pressurized liquid extraction and purification

In order to reduce time of analysis, a new pressurized liquid extraction (PLE) method that automatically and rapidly achieves quantitative and selective extraction of 39 polybrominated diphenyl ether (PBDE) congeners in sediment samples was optimized. It consists of on-line cleanup by inclusion of sorbents in the extraction cell. The new method was compared with a conventional method based on the use of Soxhlet extraction followed by solid-phase extraction (SPE) with cartridges. The instrumental determination was performed by GC-MS, using negative chemical ionization in the selected-ion monitoring mode. Recoveries from 47 to 82% were obtained for spiked tri- to hepta-PBDE congeners in sediment sample. The repeatability of replicate extractions was better than 15% relative standard deviation. The detection limits obtained with the new developed method were between 1 and 46 pg/g dry weight. The reduction in the sample preparation (extraction + cleanup) time (from days to 30 min) with a similar efficiency than that afforded by the conventional Soxhlet extraction-SPE cleanup technique indicates the suitability of this method. The method was applied to sediment samples where the analytes were detected in the range of 0.86-2.49 ng/g dry mass.     

Development of a solid phase extraction procedure for HPLC-DAD determination of several angiotensin II receptor antagonists in human urine using mixture design

The optimisation of a solid phase extraction procedure involves several variables whose influence has been widely studied. However, in most cases, only process variables are taken into account. In this work, the influence of those process variables together with the fact of using mixtures of solvents during the elution step of the solid phase extraction of four angiotensin II receptor antagonist drugs has been studied. Since the influence on the extraction efficiency of several process variables were simultaneously tested, a D-optimal design was constructed. The composition of the elution solvent (a mixture of methanol, acetonitrile, ethanol and acetone at different proportions from 0 to 100% each solvent), the percentage and pH of the buffer solution added to the urine samples at the beginning of the extraction procedure; the percentage of the organic component and the volume of the washing solution, the drying time and the volume of the elution solvent were the studied variables. The chromatographic separation was carried out by gradient elution mode with 0.026% trifluoroacetic acid (TFA) in the organic phase and 0.031% TFA in the aqueous phase using an Atlantis dC18, 100 mm × 3.9 mm I.D. chromatographic column at a flow rate of 1 mL/min and a column temperature of 35 ± 0.2 °C. For detection a diode array detector set at 232 nm was used. The extraction procedure for spiked human urine samples was developed using C8 cartridges, phosphate buffer pH 6.8 as conditioning agent, a drying step of 10 min, a washing step with methanol-phosphate buffer (20:80, v/v) and methanol as eluent. Recovery percentages obtained: 84% for eprosartan, 74% for telmisartan, 74% for irbesartan and 89% for valsartan allow the determination of these drugs concentration levels in urine.     

Microwave-assisted solvent elution technique for the extraction of organic pollutants in water

Solid phase extraction (SPE) with appropriate solid sorbents has been commonly used in the routine extraction of organic pollutants in water. The elution of analytes from the solid sorbents normally takes place by organic solvents under an applied vacuum. In this study, a microwave-assisted solvent elution technique was developed for the elution of analytes from C₁₈ membrane disks during microwave irradiation from a microwave extraction system (MES). Several parameters, namely, elution solvent, elution temperature, duration of elution and the volume of solvent which may affect the elution efficiency of microwave-assisted solvent elution (MASE) technique towards organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), phthalate esters (PAEs), organophosphorus pesticides (OPs), fungicides, herbicides and insecticides from the membrane disk were investigated. Good recoveries above 75% were obtained for most of the organic pollutants using the optimum SPE-MASE technique. The effect of sodium chloride and humic acid on the recoveries on the target analytes were also investigated.     

离线超临界流体萃取和气相色谱-红外-质谱联用测定水中有机污染物

利用吸附剂ＧＤＸ－３０１对黄河水中的有机污染物富集并以超临界ＣＯ２脱附后,通过气相色谱、色谱－红外－质谱联用技术对各目标分析物逐一定性,并比较了超临界ＣＯ２萃取和溶剂洗脱的结果。实验表明,在２０ＭＰａ,６０℃,４０ｍｉｎ条件下进行超临界ＣＯ２萃取时的萃取效率和溶剂萃取效率相当或略高。     

利用HCI程序确定儿茶酚化合物的反相高效液相色谱最佳分离条件

有效地确定了反相高效液相色谱分离儿茶酚化合物的最佳条件。在水和甲醇的二元流动相里分别加入乙酸缓冲液,利用基于ln k=ln kw +SF, k=A+B/F, ln k=L+MF+NF2 (F是流动相中有机物甲醇的体积分数)等保留因子的一次或二次方程式的塔板理论得到色谱分离结果;利用保留原理得到等度和梯度洗脱的最佳条件。得出最佳初始流动相是含0.1%乙酸的水和含0.1%乙酸的甲醇(体积比为75∶25)的混合溶液;梯度洗脱条件：初始流动相保持15 min,然后用10 min的时间将上述二元流动相的体积比线性变换成50∶50,直到完成全部分离。通过实验证实该计算结果与实验值相近。     

Use of solid-phase microextraction/gas chromatography-electron capture detection for the determination of energetic chemicals in marine samples

Gas chromatography with electron capture detection (GC-ECD) is a highly explosive-sensitive analytical technique. However, its application to the analysis of sediment extracts is hampered by the presence of numerous endogenous interferences. In the present study, solid-phase microextraction (SPME) was used both as a purification technique for sediment extracts and as an extraction technique for water samples prior to analysis by GC-ECD. SPME/GC-ECD coupling was optimized and applied to the trace analysis of nine explosives including nitroaromatics and RDX in real seawater and marine sediment samples. Addition of a high concentration of salt (30%, w/v) in the aqueous medium and use of a carbowax/divinylbenzene (CW/DVB) coating led to optimal extraction efficiencies. Method detection limits (MDLs) ranged from 0.05 to 0.81 microg/L in water and from 1 to 9 microg/kg in dry sediment. Except for RDX, spike recoveries in seawater were satisfactory (89-147%) when samples were fortified at 2 microg/L of each analyte. Spike recoveries from dry sediment fortified at 10 microg/kg of each analyte gave lower recoveries but these could also be due to degradation in the matrix. With a smaller volume of aqueous sample required compared to solid-phase extraction (SPE), SPME is an attractive method for the analysis of limited volumes of sediment pore-water. Moreover, the use of SPME eliminated interferences present in sediment extracts thus allowing the detection of the target analytes that were otherwise difficult to detect by direct injection.     

Electrokinetic sample extraction and enrichment: a new method for the isolation of analytes from sludge-type matrices

Electrokinetic sample extraction and enrichment is introduced as a newly developed concept for the analysis of substances in sludge-type or paste-like matrices. It is based on electrokinetic transport phenomena as electromigration and electroosmosis occurring when an electrical field is applied to the fresh, wet samples. Problems usually associated to sample drying can be avoided, e.g., losses of volatile analytes or contamination. We have designed and built a suitable apparatus for electrokinetic sample extraction and enrichment. Appropriate operating conditions (field strength, buffer composition, concentration, and volume) were identified in experiments with an artificial sludge model and real-world lake sediments. A proof of principle of the method was provided by the electromigrative extraction and online enrichment on a solid-phase sorbent disk of an azo dye from a diatomaceous earth slurry. Electroosmotic extraction and enrichment of a cyanobacterial hepatotoxin at trace levels was finally investigated as an application example using lake sediments. Rather clean extracts were obtained even with high organic content sediment samples, as shown by high-performance liquid chromatography with diode array detection.      

高效液相色谱-串联质谱法同时测定水中13种有机污染物

以地表水环境质量标准严格控制的特定项目为依据,建立了直接进样-高效液相色谱-串联质谱同时测定水中13种化学性质差异较大的有机污染物的分析方法,这13种有机污染物为乐果、敌敌畏、敌百虫、对硫磷、甲基对硫磷、马拉硫磷、内吸磷、丙烯酰胺、苯胺、联苯胺、甲萘威、微囊藻毒素-LR、阿特拉津。水样经0.22 μm尼龙66滤膜过滤后,采用Kromasil 100-5 C18柱(150 mm×2.1 mm, 5 μm)分离,以甲醇-0.01%甲酸水溶液为流动相进行梯度洗脱,流速0.5 mL/min,柱温40 ℃,电喷雾正离子模式(ESI⁺)电离,多反应监测模式(MRM)进行检测,外标法定量。13种化合物的浓度与其峰面积在一定浓度范围内均呈现良好的线性关系(r≥0.9995),方法检出限为0.02~0.1 μg/L。测定低、中、高浓度的加标样品,13种化合物的相对标准偏差为0.5%~5.0%(n=6),实际样品加标平均回收率为81.2%~112%。此方法灵敏度高、干扰小、分析速度快,可适用于地表水、地下水中这13种有机污染物的同时分析。     

Extraction and analysis of pharmaceuticals in polluted sediment using liquid chromatography mass spectrometry

A multi-residue method for the extraction and clean-up of sediment samples was developed for the analysis of pharmaceutical residues. Sediment samples were collected in the proximity of sewage water plant in Stockholm, Sweden. Target analytes were the basic β-blocker propranolol, the neutral neuroleptic carbamazepine and the acidic anticoagulant warfarin, the painkiller diclofenac and the lipid regulator gemfibrozil. The extraction solvent was optimised with regard to pH and organic modifer. Extraction and clean up were performed with liquid-liquid extraction and ultra-sonication followed by solid-phase extraction. One extraction solvent, containing acetone/McIlvaine buffer pH4, provided satisfactory extraction for all substances. LC/MSMS in the MRM mode was used for determination. The recoveries of the extraction and clean-up steps were 60–75% (±2–8%) and LOQs were in the range 0.4–8?ng/g sediment (dry weight). The pharmaceuticals found in the sediment samples were propranolol and carbamazepine, representing substances with basic and neutral properties. Additionally, the samples were analysed with LC/QTOF for verification with the use of accurate mass measurement in the full-scan mode. Pharmaceuticals not represented in the original method were looked for. Non-target pharmaceuticals found using the LC/QTOF system were the basic β-blocker metoprolol and the acidic painkiller naproxen.     

快速溶剂萃取-离子色谱法测定茶叶中的有机酸

建立了快速溶剂萃取-离子色谱法（ASE—IC）测定茶叶中的9种有机酸。优化了ASE苹取条件,以水为萃取溶剂,80℃下萃取5min,循环两次。采用Ionpac AS11HC柱分离,KOH溶液梯度洗脱,流速1,0mL／min,抑制电导检测。9种有机酸的检出限为0．009-0．160μg／mL,线性范围为0．5—10μg／mL,相关系数大于0．999,加标回收率为93．4％-99．2％,相对标准偏差为1．4％-4．1％。     

Quantitative Speciation of Arsenic in Water and Sediment Samples from the Mokolo River in Limpopo Province,South Africa

The Mokolo River is disposed to environmental contaminants such as arsenic (As) due to its proximity to several anthropogenic activities. Speciation of As in water and sediment samples from Mokolo River is crucial to evaluate the level and distribution of As in the river and underlying sediment since toxicity depends on its chemical forms. In this study, As species in water and sediment were determined by developing a new method for sediment extraction. Effective microwave-assisted extraction of As species in sediment samples was achieved using 0.3?M (NH₄)₂HPO₄ and 50?mM EDTA, which showed no species interconversion during extraction. The chromatographic separation and detection of As(III), dimethylarsinic acid (DMA), monomethylarsonic acid, and As(V) in water and sediment samples were achieved by coupling to high-performance liquid chromatography to inductively coupled plasma mass spectrometry. Baseline separation of four As species was achieved in 12?min using gradient elution with 10 and 60?mM NH₄NO₃ at pH 8.7 as the mobile phase. The analytical figures of merit and validation of analytical procedures were assessed and adequate performance and percentage recoveries ranging from 81.1 to 102% for water samples and 73.0–92.0% for sediments were achieved. The As species concentration in water and sediment samples was found to be in the range of 0.304–4.99?µg?L^?1 and 74.0–92.0?ng?g^?1, respectively. DMA was not detected in both water and sediment samples.     

Liquid chromatography/tandem mass spectrometric bioanalysis using normal-phase columns with aqueous/organic mobile phases - a novel approach of eliminating evaporation and reconstitution steps in 96-well SPE

Bioanalytical methods using automated 96-well solid-phase extraction (SPE) and liquid chromatography with electrospray tandem mass spectrometry (LC/MS/MS) are widely used in the pharmaceutical industry. SPE methods typically require manual steps of drying of the eluates and reconstituting of the analytes with a suitable injection solvent possessing elution strength weaker than the mobile phase. In this study, we demonstrated a novel approach of eliminating these two steps in 96-well SPE by using normal-phase LC/MS/MS methods with low aqueous/high organic mobile phases, which consisted of 70-95% organic solvent, 5-30% water, and small amount of volatile acid or buffer. While the commonly used SPE elution solvents (i.e. acetonitrile and methanol) have stronger elution strength than a mobile phase on reversed-phase chromatography, they are weaker elution solvents than a mobile phase for normal-phase LC/MS/MS and therefore can be injected directly. Analytical methods for a range of polar pharmaceutical compounds, namely, omeprazole, metoprolol, fexofenadine, pseudoephedrine as well as rifampin and its metabolite 25-desacetyl-rifampin, in biological fluids, were developed and optimized based on the foregoing principles. As a result of the time saving, a batch of 96 samples could be processed in one hour. These bioanalytical LC/MS/MS methods were validated according to "Guidance for Industry - Bioanalytical Method Validation" recommended by the Food and Drug Administration (FDA) of the United States.     

Gas chromatography-mass spectrometric determination of fthalide and heptachlor epoxide in environmental samples

Methods were developed to determine traces of 4,5,6,7-tetrachlorophthalide (fthalide) and 1,4,5,6,7,8,8-heptachloro-2,3-epoxy-2,3,3a,7a-tetrahydro-4,7-methanoindene (heptachlor epoxide) in environmental samples such as river water, sediment and fish. The samples were cleaned up by using convenient disk type solid phase extractors and cartridges and analyzed by GC/MS with selected ion monitoring. Fthalide and heptachlor epoxide in water samples could be determined in the range 0.1-0.3 ng ml(-1) with relative standard deviations (RSDs) of 1.0-4.8%. The estimated detection limits were 0.020-0.031 ng ml(-1), 5.1-7.3 ng g(-1) and 2.7-4.2 ng g(-1) in water, sediment and fish samples, respectively. The recoveries were 96-103, 99-101, 66-85 and 67-77% with RSDs of 4.3-10.2, 2.4-2.5, 4.6-5.2 and 2.1-3.8% in river water, sea water, sediment and fish samples, respectively.     

Optimization of a Multiresidue Analysis of 65 Pesticides in Surface Water Using Solid-Phase Extraction by LC-MS/MS

An analytical method was developed and validated for simultaneous quantitation of 65 pesticides, including one single solid-phase extraction (SPE) procedure in surface water by liquid chromatography coupled to tandem mass spectroscopy. Different parameters that have an influence on extraction efficiency were evaluated in this research. Different types of cartridges, elution solvents, and sorbent drying time were investigated, and the most appropriate one was selected. Moreover, various pretreatment techniques were applied to remove sediments from water without the loss of pesticides. Centrifugation was introduced as the best option at the beginning of sample preparation to resolve the clogging of the sorbent cartridges. The recoveries of all pesticides ranged from 70% to 120%, with a relative standard deviation of less than 13.7%. The feasibility of the method was evaluated on 10 surface water samples with different concentrations of sand, sediment, and particles.     

Micellar and aqueous‐organic liquid chromatography using sub‐2 μm packings for fast separation of natural phenolic compounds

The objective of the present work was to investigate the chromatographic behavior of natural phenolic compounds in micellar and aqueous‐organic LC using a short column packed with 1.8 μm particles. Firstly, the effect of ACN and SDS on elution strength and selectivity was examined by isocratic submicellar (0–30% ACN/5% 1‐butanol/1–6 mM SDS) and micellar (0–30% ACN/5% 1‐butanol/40–60 mM SDS) systems. The varied concentrations of two modifiers in the mobile phases revealed different eluting power. Then, the application of organic modifier gradient was discussed in both submicellar and micellar LC using mobile phases of 4 mM SDS/5% 1‐butanol or 50 mM SDS/5% 1‐butanol containing ACN gradient from 0 to 30%, respectively. For micellar system, the separation was found to be better in gradient than isocratic elution. Additionally, the sensitivity of aqueous‐organic LC was examined. The mobile phase was a mixture of ACN and water employing gradient elution at a flow rate of 0.5 mL/min, with analysis time below 9 min. It was found that separation efficiency was significantly better compared with micellar LC. Besides, the aqueous‐organic LC has been applied to separation of various phenolic compounds in Yangwei granule or Radix Astragali samples.     

Nanostructured collagen layers obtained by adsorption and drying

The supramolecular organization of collagen adsorbed from a 7 microg/ml solution on polystyrene was investigated as a function of the adsorption duration (from 1 min to 24 h) and of the drying conditions (fast drying under a nitrogen flow, slow drying in a water-saturated atmosphere). The morphology of the created surfaces was examined by atomic force microscopy (AFM), while complementary information regarding the adsorbed amount and the organization of the adsorbed layers was obtained using radioassays, X-ray photoelectron spectroscopy (XPS), and wetting measurements. The collagen adsorbed amount increased up to an adsorption duration of 5 h and then leveled off at a value of 0.9 microg/cm2. For samples obtained by fast drying, modeling of the N/C ratios obtained by XPS in terms of thickness and surface coverage, in combination with the adsorbed amount, water contact angle measurements and AFM images, indicated that the adsorbed layer formed a felt starting from 30 min of adsorption, the density and/or the thickness of which increased with the adsorption time. Upon slow drying, the collagen layers formed after adsorption times up to about 2 h underwent a strong reorganization. The obtained nanopatterns were attributed to dewetting, the liquid film being ruptured and adsorbed collagen being displaced by the water meniscus. At higher adsorption times, the organization of the collagen layer was similar to that obtained after fast drying, because the onset of dewetting and/or collagen displacement were prevented by the high density of the collagen felt.     

Determination of total phosphorus and nitrogen in turbid waters by oxidation with alkaline potassium peroxodisulfate and low pressure microwave digestion, autoclave heating or the use of closed vessels in a hot water bath: comparison with Kjeldahl digestion

The evaluation of the use of alkaline peroxodisulfate digestion with low pressure microwave, autoclave or hot water bath heating for the determination of total phosphorus and nitrogen in turbid lake and river waters is described. The efficiency of these digestion procedures were compared to a Kjeldahl digestion procedure with sulphuric acid-potassium sulfate and copper sulfate. The final solution before digestion was 0.045 M in potassium peroxodisulfate and 0.04 M in sodium hydroxide. Procedures were evaluated by the analysis of suspensions of two reference materials, National Institute of Environmental Science, Japan, no. 3 Chlorella and no. 2 pond sediment and natural turbid waters. Best recoveries of phosphorus and nitrogen by microwave heating were obtained when solutions were digested at 95 °C for 40 min. Quantitative recoveries of phosphorus from Chlorella suspensions up to 1000 mg/l were obtained by all three heating procedures, but incomplete recoveries of nitrogen occurred above 20 mg N/l in the digested sample. Good recoveries of phosphorus and nitrogen from suspended sediment suspensions were obtained only from solutions containing <150 mg/l of suspended sediments. Recoveries of phosphorus from phosphorus compounds containing COP and CP bonds added to distilled water were quantitative (94-113%) except for polyphosphates (microwave, 34±8; autoclave, 114±6; water bath, 96±4) and aluminium phosphate (8-23%). Recoveries of nitrogen compounds containing CN bonds added to distilled water were quantitative (94-96%). The analysis of a range of natural turbid water samples by alkaline peroxodisulfate and microwave, autoclave and water bath heating gave similar total phosphorus and nitrogen results. All procedures using alkaline peroxodisulfate underestimate phosphorus concentrations at high suspended sediment concentrations (>150 mg/l) and are only suitable for the analysis of very turbid samples when the turbidity is due to organic matter (algal cells, plant detritus). Underestimation of nitrogen occurs when samples contain more than 20 mg N/l.