Miscibility study in the blends of novel poly (styrene-co-4-vinylphenyldimethylsilanol) and poly (n-butyl methacrylate)

The miscibility of poly (styrene-co-4-vinylphenyldimethylsilanol) (ST-VPDMS) and poly (n-butyl methacrylate) (PBMA) blends has been investigated by means of DSC and FT-IR spectroscopy. It was found that miscible blends were formed only for the copolymers containing 9–34 mol % 4-vinylphenyldimethylsilanol (VPDMS). The glass transition behavior of the miscible blends was analyzed by recently proposed equations in terms of the physical meaning of the fitting parameters. The results of FT-IR study were found to be fully consistent with the observation of the miscibility window obtained from glass transition temperature measurements. Quantitative information concerning intermolecular hydrogen bond interaction in the carbonyl stretching vibration region of the miscible blends was obtained by curve-fitting method. © 1994 John Wiley & Sons, Inc.     

Confocal microscopy studies of shear‐induced coalescence in blends of poly(butyl methacrylate) and poly(2‐ethylhexyl methacrylate)

This article reports the results of confocal fluorescence microscopy studies of shear‐induced coalescence in binary blends of poly(2‐ethylhexyl methacrylate) (PEHMA; 90 wt %) and poly(butyl methacrylate) (PBMA; 10 wt %). We prepared the blends by casting a mixture of latex dispersions of the components onto a substrate and allowing the film to dry under ambient conditions. The initial morphology of the film was a dispersion of 120‐nm PBMA spheres in a continuous PEHMA matrix. One‐fifth of the PBMA particles were labeled with anthracene, the emission of which we observed with confocal microscopy. The blends were sheared in a parallel‐plate rheometer at 80 and 100 °C for 1 and 10 h. Careful image analysis allowed us to estimate the mean size of the dispersed phase and the width of the size distribution. The results were compared with the theoretical limits of Wu and Taylor. After 10 h of shearing, the mean particle size decreased and the particle distribution became narrower in comparison with the results obtained after 1 h of shearing. We explain this result by inferring that before the sample reached steady‐state morphology, its rate of coalescence was greater than the rate of particle breakup. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2317–2332, 2001     

Miscibility of poly(ε-caprolactone), a semicrystalline polymer,with amorphous poly(styrene-4-hydroxystyrene) copolymers

The miscibility of poly(ε caprolactone) (PCL) with poly(styrene-co-4-hydroxystyrene) (PHS) copolymers was investigated as a function of comonomer composition experimentally and with calculations by two models; the binary interaction model and the association model. PCL was found to be completely miscible with PHS copolymers containing 5 or more mole percent of 4-hydroxystyrene (HS) comonomer units for the entire range of blend compositions. Segmental interaction densities, B_ijs, were determined by the analysis of the equilibrium melting point depression and by the application of the binary interaction model. By correlating the segmental interaction energy densities with the binary interaction model, thermodynamic miscibility is for comonomer composition over five mole percent of 4-hydroxystyrene, which is in agreement with the experimental phase behavior. Application of the association model for specific interactions to blends also predicts the experimental miscibility boundary and phase behavior for all the PHS copolymers/PCL blends. © 1995 John Wiley & Sons, Inc.     

The conformation of poly(3-dodecyl thiophene) within methacrylic polymer matrix

Blends of poly(3-dodecyl thiophene) (PDDT) with poly(methyl methacrylate), poly(butyl methacrylate) (PBMA), and poly(methyl methacrylate-co-butyl methacrylate) (PMMA/PBMA) were studied by polarization optical microscopy, atomic-force microscopy, and absorption spectroscopy and were modeled using molecular dynamics (MD) simulations. The observed thermochromic transitions are shown to be host-matrix dependent, with PDDT/PBMA absorption spectra differing substantially from pristine PDDT. The dispersion of PDDT within PBMA matrix is observed to be greater than in the other host polymers. MD calculations of both individual PDDT molecules and molecular aggregates suggest that the distribution of dihedral angles present in the PDDT backbone is the narrowest for aggregates of PDDT embedded within a polymer matrix. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2909–2917, 1999     

Miscibility windows for poly(styrene-co-vinyl phenol) blends with poly(alkyl methacrylate)s: Further comparisons of theoretical predictions to FTIR experimental data

We report the results of theoretical and experimental studies of styrene-co-vinyl phenol (STVPh) copolymer blends with poly(n-octyl methacrylate) (POMA) and poly(n-decyl methacrylate) (PDMA). This work is a natural extension to our recently reported studies of the phase behavior of analogous STVPh blends with poly(n-butyl methacrylate) (PBMA) and poly(n-hexyl methacrylate) (PHMA) where we employed an association model together with parameters obtained from studies of miscible homopolymer blends. The theoretically calculated miscibility maps for STVPh copolymer blends with the homologous series of poly(n-alkyl methacrylates) (PAMA) are in fine agreement with experiment.     

Novel Silanol-Containing Polymers and Their Blends

ABSTRACT

Novel 4-vinylphenyldimethylsilanol polymer (PVPDMS) and co-polymers (ST-VPDMS) were synthesized by the oxyfunctionalization re- action of the silane. The reaction was found to proceed efficiently and quantitatively. Miscibility studies indicated that about 4 molpercnt; of 4-vin- ylphenyldimethylsilanol (VPDMS) functional group in the copolymer could achieve miscibility with poly(n-butyl methacrylate) (PBMA) and poly(N-vinylpyrrolidone) (PVPr). However, for copolymers containingmore than 34 molpercnt; VPDMS, their blends with PBMA were immiscible. The observed miscibility window of ST-VPDMS/PBMA blends was as- cribed to the competition between the self-association of dimethylsilanol groups and intermolecular hydrogen bonding of dimethylsilanol groups with the carbonyl groups of PBMA. A comparison of the efficiency of the miscibility enhancement and the miscibility windows of VPDMS, p-(hexafluoro-2-isopropyl) styrene (HFPS), and phenolic-containing polymers was made in terms of such competition. The glass transition behavior of the miscible blends involving VPDMS and HFPS-containing styrene copolymers with PBMA were analyzed by the Schneider equation.     

Polypropylene/poly(butyl methacrylate) blends prepared by diffusion and subsequent polymerization of butyl methacrylate in isotactic polypropylene pellets

Polypropylene/poly(butyl methacrylate)(PP/PBMA) blends were prepared by diffusion and subsequent polymerization of butyl methacrylate(BMA) in commercial isotactic polypropylene(iPP) pellets.The diffusion kinetics,diametrical distribution of PBMA in a pellet and phase morphology of a typical PP/PBMA blend were investigated.     

以离子-离子相互作用增强共混相容性Ⅰ.聚苯醚离聚体/聚(苯乙烯-乙烯吡啶)共混体系

本文从溶液行为和固体热行为对聚（2，6-二甲基1，4-苯醚）（PPO）离聚体（磺化聚苯醚或接化聚苯醚）／聚（苯乙烯-4-乙烯吡啶）（PS－VP）共混物进行了研究。DSC研究表明磺化度为7．7％mol的SPPO／PS－VP和羧化度为15％molCPPO炉S－VP在整个组成范围都是相容的。溶液行为研究表明，与对应的PPO／PS－VP共混物相比，这两个系列的共混物都表现出较高的比浓粘度。这是由于聚苯醚离聚体上的酸基发生质子转移，两组分间强烈的离子-离子相互作用导致分子间的络合，从而使比浓粘度的提高，也正是这种离子-离子相互作用使得这两对共混物完全相容。     

Synthesis of poly(styrene-co-3-trimethoxysilyl propyl methacrylate) microspheres coated with polysiloxane layer

A procedure has been developed to coat micron-sized poly(styrene-co-3-trimethoxysilyl propyl methacrylate) microspheres with a smooth layer of polysiloxane by the hydrolysis and condensation of methyl trimethoxylsilane (MTMS). Firstly, polystyrene microspheres containing silanol groups were prepared by conventional dispersion polymerization using 3-(trimethoxysilyl) propyl methacrylate (MPS) as a functional comonomer in an ethanol/water medium. Secondly, the synthesis of the polysiloxane shell was carried out using a sol–gel process of MTMS. The thickness of the shells can be easily varied with different copolymer seeds and MTMS feed ratio. When we used copolymer particles with 2.00 μm diameter as seeds, the thickness of the polysiloxane shells can be varied from 0.10 to 0.18 μm. The core/shell structure of the composite microspheres was characterized by transmission electron microscope (TEM).     

Miscibility and transesterification in ternary blends of poly(ethylene naphthalate)/poly(trimethylene terephthalate)/poly(ether imide)

Miscibility and morphology of poly(ethylene 2,6-naphthalate)/poly(trimethylene terephthalate)/poly(ether imide) (PEN/PTT/PEI) blends were investigated by using a differential scanning calorimeter (DSC), optical microscopy (OM), wide-angle X-ray diffraction (WAXD), and proton nuclear magnetic resonance (¹H-NMR). In the ternary blends, OM and DSC results indicated immiscible properties for polyester-rich compositions of PEN/PTT/PEI blends, but all compositions of the ternary blends were phase homogeneous after heat treatment at 300 °C for more than 30 min. An amorphous blend with a single T _g was obtained in the final state, when samples were annealed at 300 °C. Experimental results from ¹H-NMR identified the production of PEN/PTT copolymers by so-called “transesterification”. The influence of transesterification on the behaviors of glass transition and crystallization was discussed in detail. Study results identified that a random copolymer promoted the miscibility of the ternary blends. The critical block lengths for both PEN and PTT hindered the formation of crystals in the ternary blends. Finally, the transesterification product of PEN/PTT blends, ENTT, was blended with PEI. The results for DSC and OM demonstrated the miscibility of the ENTT/PEI blends.     

Latices of poly(fluoroalkyl mathacrylate)‐b‐poly(butyl methacrylate) copolymers prepared via reversible addition–fragmentation chain transfer polymerization

Poly(fluoroalkyl mathacrylate)‐block‐poly(butyl methacrylate) diblock copolymer latices were synthesized by a two‐step process. In the first step, a homopolymer end‐capped with a dithiobenzoyl group [poly(fluoroalkyl mathacrylate) (PFAMA) or poly(butyl methacrylate) (PBMA)] was prepared in bulk via reversible addition–fragmentation chain transfer (RAFT) polymerization with 2‐cyanoprop‐2‐yl dithiobenzoate as a RAFT agent. In the second step, the homopolymer chain‐transfer agent (macro‐CTA) was dissolved in the second monomer, mixed with a water phase containing a surfactant, and then ultrasonicated to form a miniemulsion. Subsequently, the RAFT‐mediated miniemulsion polymerization of the second monomer (butyl methacrylate or fluoroalkyl mathacrylate) was carried out in the presence of the first block macro‐CTA. The influence of the polymerization sequence of the two kinds of monomers on the colloidal stability and molecular weight distribution was investigated. Gel permeation chromatography analyses and particle size results indicated that using the PFAMA macro‐CTA as the first block was better than using the PBMA RAFT agent with respect to the colloidal stability and the narrow molecular weight distribution of the F‐copolymer latices. The F‐copolymers were characterized with ¹H NMR, ¹⁹F NMR, and Fourier transform infrared spectroscopy. Comparing the contact angle of a water droplet on a thin film formed by the fluorinated copolymer with that of PBMA, we found that for the diblock copolymers containing a fluorinated block, the surface energy decreased greatly, and the hydrophobicity increased. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 471–484, 2007     

Melting behavior,miscibility, and hydrogen-bonded interactions of poly(ε-caprolactone)/poly(4-hydroxystyrene-co-methoxystyrene) blends

The miscibility of poly(4-hydroxystyrene-co-methoxystyrene) (HSMS) and poly(ε-caprolactone) (PCL) was investigated by differential scanning calorimetry and Fourier transform infrared spectroscopy (FTIR). HSMS/PCL blends were found to be miscible in the whole composition range by detecting only a glass transition temperature (T_g), for each composition, which could be closely described by the Fox rule. The crystallinity of PCL in the blends was dependent on the T_g of the amorphous phase. The greater the HSMS content in the blends, the lower the crystallinity. The polymer–polymer interaction parameter, χ₃₂, was calculated from melting point depression of PCL using the Nishi-Wang equation. The negative value of χ₃₂ obtained for HSMS/PCL blends has been compared with the value of χ₃₂ for poly(4-hydroxystyrene) (P4HS)/PCL blends. The specific nature, quantitative analysis, and average strength of the intermolecular interactions in HSMS/PCL and P4HS/PCL blends have been determined at room temperature and in the molten state by means of Fourier transform infrared spectroscopy (FTIR) measurements. The FTIR results have been in good correlation with the thermal behavior of the blends. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 95–104, 1998     

Miscibility and Thermal Behaviour of Poly(styrene-co-itaconic acid)/Poly(butyl methacrylate-co-4-vinylpyridine) Mixtures. Accessibility and Self-Association Effects

Summary: The miscibility and thermal behaviour of binary mixtures of poly(styrene-co-itaconic acid) containing 11 or 27 mol % of itaconic acid (PSIA-11 or PSIA27) with poly(butyl methacrylate) (PBMA)or poly(butyl methacrylate-co-4-vinylpyridine) containing 10 or 26 mol% of 4-vinylpyridine (PBM4VP-10, PBM4V-P26) were investigated by differential scanning calorimetry, scanning electron microscopy, FTIR spectroscopy and thermogravimetry. The results showed that 11 mol % of itaconic acid and 10 mol % of 4-vinylpyridine respectively introduced within the polystyrene and poly(butyl methacrylate) matrices induced the miscibility of this pair of polymers due to specific interactions of hydrogen bonding type with partial pyridine protonation that occurred between the two copolymers as evidenced by FTIR from the appearance of two new bands at 1607 cm⁻¹ and 1640 cm⁻¹. Increasing itaconic acid content from 11 to 27 mol % led to a decrease of the intensity of the specific interactions within PSIA-27/PBM4VP blends and is attributed to both accessibility and self association effects as evidenced by DSC from the change of the shape of the Tg- composition curves and by FTIR spectroscopy. As shown from the thermogravimetric study, the presence of these specific interactions delayed the anhydride formation and improved the thermal stability of the blends.     

Miscibility in blends of poly(3-hydroxybutyrate) and poly(vinylidene chloride-co-acrylonitrile)

Miscibility behavior of poly(3-hydroxybutyrate) [PHB]/poly(vinylidene chloride-co-acrylonitrile) [P(VDC-AN)] blends have been investigated by differential scanning calorimetry and optical microscopy. Each blend showed a single T_g, and a large melting point depression of PHB. All the blends containing more than 40% PHB showed linear spherulitic growth behavior and the growth rate decreased with P(VDC-AN) content. The interaction parameter χ₁₂, obtained from melting point depression analysis, gave the value of −0.267 for the PHB/P(VDC-AN) blends. All results presented in this article lead to the conclusion that PHB/P(VDC-AN) blends are completely miscible in all proportions from a thermodynamic viewpoint. The miscibility in these blends is ascribed to the specific molecular interaction involving the carbonyl groups of PHB. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2645–2652, 1997     

Effect of oligomers on the polymer diffusion rate in poly(butyl methacrylate) latex films

The aqueous phase of a poly(butyl methacrylate) (PBMA) latex dispersion contained an oligomeric component that was isolated after sedimentation of the PBMA latex particles. The component contained both water‐soluble PBMA oligomer and some longer chain species that were present as a very fine colloidal dispersion. We describe the isolation and characterization of this component. This component was then added to a purified PBMA latex dispersion from which the aqueous component was previously removed. Latex films were prepared, and in the presence of the oligomeric material, the rate of polymer diffusion in the latex film was strongly enhanced. The magnitude of the enhancement was fit quantitatively to the Fujita–Doolittle equation, indicating that the oligomers acted like a traditional plasticizer to increase the free volume in the system. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3933–3943, 2000     

Preparation of silica-coated poly(styrene-co-4-vinylpyridine) particles and hollow particles

This paper presents a novel method for preparation of polymer-silica colloidal nanocomposites based on emulsion polymerization and subsequent sol-gel nanocoating process. The polystyrene latex particles bearing basic groups on their surfaces were successfully synthesized through emulsion polymerization using 4-vinylpyridine (4VP) as a functional comonomer and polyvinylpyrrolidone (PVP) as a surfactant. A series of poly(styrene-co-4-vinylpyridine)/SiO2 nanocomposite particles with smooth or rough core-shell morphology were obtained through the coating process. The poly(styrene-co-4-vinylpyridine) particles could be dissolved subsequently or simultaneously during the sol-gel coating process to form hollow particles. The effects of the amount of 4VP, PVP, NH(4)OH, and tetraethoxysilane (TEOS) on both the nanocomposite particles and hollow particles were investigated. Transmission electron microscopy showed that the morphology of the nanocomposite particles and hollow particles was strongly influenced by the initial feed of the comonomer 4VP and the coupling agent PVP. The conditions to obtain all hollow particles were also studied. Thermogravimetric analysis and energy dispersive X-ray spectroscopy analyses indicated that the interiors of hollow particles were not really "hollow".     

Melt‐processable blends of ionic poly(p‐phenylene terephthalamide) and poly(4‐vinylpyridine): Relaxation behavior

Melt‐processable blends were prepared from rigid molecules of an ionically modified poly(p‐phenylene terephthalamide) (PPTA) and flexible‐coil molecules of poly(4‐vinylpyridine) (PVP). Dynamic mechanical analyses of blends with 50% or more of the ionic PPTA component revealed the presence of two distinct phases. The glass‐transition temperature of the more stable, ionic PPTA‐rich phase increased linearly with the ionic PPTA content. The second phase present in these blends was an ionic PPTA‐poor, or a PVP‐rich, phase. For this phase, a reasonably good fit of the data, showing the glass‐transition temperature as a function of the ionic PPTA content, was achieved between the results of this study and the reported results of previous investigation of molecular composites of the same two components with ionic PPTA contents of 15 wt % or less. The possible influence of annealing on the blend structure of a 90/10 blend of ionic PPTA and PVP was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1468–1475, 2003     

Miscibility and crystallization behavior in blends of poly(methyl methacrylate) and poly(vinylidene fluoride): Effect of star‐like topology of poly(methyl methacrylate) chain

A tetraarmed star‐shaped poly(methyl methacrylate) (s‐PMMA) was synthesized via atom transfer radical polymerization with 2‐bromoisobutyryl pentaerythritol as the initiator. For comparison, a linear PMMA with the identical molecular weight (l‐PMMA) was also prepared. The blends of the two PMMA samples with poly (vinylidene fluoride) (PVDF) were prepared to investigate the effect of macromolecular topological structure on miscibility and crystallization behavior of the binary blends. The behavior of single and composition‐dependent glass transition temperatures was found for the blends of s‐PMMA with PVDF, indicating that the s‐PMMA is miscible with PVDF in the amorphous state just like l‐PMMA. The miscibility was further evidenced by the depression of equilibrium melting points. It is found that the blends of s‐PMMA and PVDF displayed the larger k value of Gordon–Taylor equation than the blends of l‐PMMA and PVDF blends. According to the depression of equilibrium melting points, the intermolecular parameters for the two blends were estimated. It is noted that the s‐PMMA/PVDF blends displayed the lower interaction parameter than l‐PMMA/PVDF blends. The isothermal crystallization kinetics shows that the crystallization of PVDF in the blends containing s‐PMMA is faster than that in the blends containing the linear PMMA. The surface‐folding free energy of PVDF chains in the blends containing s‐PMMA is significantly lower than those in the blends containing l‐PMMA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2580–2593, 2007     

Graft copolymers having hydrophobic backbone and hydrophilic branches. X. Preparation and properties of water-dispersible polyanionic microspheres having poly(methacrylic acid) branches on their surfaces

The free radical copolymerization of poly(t-butyl methacrylate) (PBMA) macromonomer with styrene in ethanol give monodispersed microspheres with 0.8-1.6 μm diameter. The resulting microspheres were treated with HCl solution to convert into anionic microspheres having poly(methacrylic acid) chains. ESCA analysis of the microsphere surface suggested that PBMA chains were favorably located on the surface of the microspheres. The particle size of the microspheres decreased with increasing molecular weight and concentration of the macromonomer. Water dispersibilities of the microspheres were evaluated by measuring the relative turbidity of the suspension of microspheres as a function of pH. The results show that they were strongly dependent on pH. © 1995 John Wiley & Sons, Inc.     

Morphology and properties of poly(vinyl chloride)–poly(butadiene-co-acrylonitrile) blends

The objective of this research was to study the structure-property relationships of two poly(vinyl chloride) (PVC)–poly(butadiene-co-acrylonitrile) (BAN) blends which exhibit differences in blend compatibility. Studies were carried out utilizing differential scanning calorimetry, dynamic mechanical testing, stress–strain, transmission electron microscopy (TEM), and infrared dichroism experiments at different temperatures. The BAN 31/PVC (BAN containing 31% acrylonitrile) system is considered to be nearly compatible as evidenced by T_g shifts, stress–strain results, orientation characteristics, and TEM micrographs. Similar experiments indicate that the BAN 44/PVC system is incompatible, and contains a mixed phase of BAN 44-PVC and a pure BAN 44 phase. The extent of heterogeneity in the compatible BAN 31/PVC system, however, plays an important role in the orientation characteristics of the blends.