稀土元素La掺杂BaFe12O19微结构和磁性能的研究术

用固相法制备了镧掺杂M型钡铁氧体（Ba1--xLaxFel2O19,x=0．0-0．6）,针对不同取代量与不同温度的烧结,研究取代量和温度对钡铁氧体微结构和磁性能的影响．在烧结温度为1100-1175℃,当X=0．0-0．6时,样品主要有单一的六角M型钡铁氧体相构成．SEM表明,La离子的加入不会影响钡铁氧体微观形貌．在磁性能方面,随着La离子的增加,钡铁氧体的饱和磁化强度先增加后减小,矫顽力逐渐增加．在同一取代量下,钡铁氧体的饱和磁化强度随烧结温度升高呈现上升趋势,矫顽力随着烧结温度的升高而降低．饱和磁化强度在x=0．2,烧结温度1175℃时达到最大值62．8emu／g,矫顽力在x=0．6,烧结温度1125℃时达到最大值3911．5Oe．     

用于光学纳米干涉仪温度控制的多路控温仪

温度变化是影响纳米干涉仪的一个重要的因素。介绍了一种精密的温度控制仪器 ,它以DS162 4为温度传感器 ,利用单片机AT89C5 2进行数据的采集、传送、温度的控制 ,利用数字式电位器实现低成本的模拟量控制方案。标定后可以实现 0 .0 5℃测量精度。这种温度控制仪具有RS2 3 2通用接口 ,能够与上位计算机相连 ,实现温度的长时间测量和远程温度控制 ,利用PC机的计算能力得出被控系统的模型参数。实验表明在 0 .5h内 ,干涉仪达到热平衡 ,温度变化小于 0 .0 5℃。     

同轴型行波热声热机的实验研究

自行设计搭建了国际首台同轴型行波热声热机的实验装置 ,以氮气为工质 ,获得频率为1 3 7Hz的谐振声波。回热器热端温度达到 2 0 0℃左右时 ,热声热机开始起振 ,平均振幅 0 .1 4bar     

六方MoN的合成新路线

 在高温高压极端条件下利用CH₄Cl还原二氧化钼的方法合成了六方MoN。反应条件为：压力2 GPa,温度1 500 ℃,时间2 h。并利用XRD对合成产物进行了表征。经最小二乘法拟合后结果表明,该合成产物具有六方结构对称性,其晶格常数为a＝0.572 nm,c＝0.560 nm。经过对其衍射峰位和峰强进行拟合计算,并与实验结果进行比较, 结果表明 MoN 产物的空间群为P6₃/mmc,其中Mo原子位于2b (0, 0, 1/4)和6h (x, 2x, 1/4),x＝0.489。N原子位于2a (0, 0, 0)和6g (0.5, 0, 0)。所采用的方法具有反应条件易达到、反应时间短、反应产物单相性好等特点。     

钼镍镀层的制备及其光谱性能（英文）

采用电沉积法在镍合金表面制备钼镍镀层。研究钼镍镀层的硬度、磨损质量和摩擦系数、热膨胀等性能。分别用发射光谱法、能谱法、扫描电镜法和X衍射法等对钼镍镀层进行表征。在镍合金表面镀上一层钼镍镀层,可使其的硬度和耐磨性大幅度提高并减小磨擦系数,钼镍镀层的硬度为518 HV,比镍合金的硬度(300 HV)提高了72.67%;钼镍镀层的磨损质量是镍合金的磨损质量的1/1.94;镍合金和钼镍镀层的磨擦系数分别为0.640和0.559。镍合金的物理热膨胀曲线在100~120℃温度范围和570~640℃范围形成了2个峰,镍合金+钼镍镀层的物理热膨胀曲线在570~640℃范围形成了1个峰。在570~640℃范围可明显改善其热膨胀,镍合金+钼镍镀层的物理热膨胀曲线在570~640℃范围形成的峰远比镍合金的物理热膨胀曲线在570~640℃范围形成的峰小,可能是因为钼进入到镍的晶格中,抑制了镍在570~640℃范围发生晶格转变(bcc→fcc)所致。镍合金+钼镍镀层的物理热膨胀曲线在595~625℃范围形成的小峰,可能是由于MoNi_4和MoNi由半晶型结构转变为晶型结构所致。     

利用双周期光纤光栅实现应变和温度同时测量

提出了一种新颖双周期光纤光栅传感器。在同一段氢载光纤上先后写入长周期光纤光栅、短周期布拉格光纤光栅 ,利用长周期光栅和布拉格光栅对应变和温度敏感性的差异 ,可实现应变和温度的同时测量。实验中采用这种灵敏结构的双周期光栅 ,在 0～ 170 0 με和 2 0℃～ 12 0℃范围内 ,测量精度可达到± 16 με和± 0 8℃。     

R32添加剂对提高CO_2水-水热泵系统效率的实验研究

本文对CO_2系统中添加R32添加剂含量在1%~5%进行了实验研究。实验结果表明:在R32添加剂含量为5%时,压缩比明显提高;添加R32添加剂后,压缩机功率降低;系统制热效率在部分工况下明显提高,当R32添加剂含量为4%,蒸发温度为0℃时,其最大制热效率达到4.43,与CO_2纯质相比,提高近4%;当R32添加剂含量为4%,系统制冷效率达到最大,在蒸发温度为0℃时,最大值为3.87,与CO_2纯质相比,提高近7%;气体冷却器出口水温都有所降低。     

活性炭负载硅钼钒杂多酸催化苯羟基化反应

以活性炭为载体,采用回流吸附法制备了负载型硅钼钒杂多酸催化剂,以冰醋酸作溶剂,过氧化氢作氧化剂,研究了由苯直接羟基化制苯酚的催化活性。结果表明,苯为2mL,冰醋酸为15mL,过氧化氢为5mL,当负载型杂多酸的用量为0.2g、反应温度70℃、反应时间60m in时,硅钼钒催化合成苯酚的收率可达7.4%,选择性达97.1%。     

碳在钼(100)和钼(111)表面上的超结构

用一定能量的氩离子束轰击含碳、氧的钼(100)和(111)表面,不能除去表面上的碳。而用能量为1千电子伏,束流为6微安的氮离子轰击10—15分钟,氮在表面的吸附达到饱和值。加热到400—600℃之间碳、氧从表面上基本消失,600—650℃之间吸附在表面上的氮大量脱附,即氮峰陡降到较低值,碳又偏析到表面上。加热到730℃和775℃氮从表面消失,分别得到碳在钼(100)表面上的p(2×2)和c(6×2)结构。而若将大量脱附氮的钼(111)表面,冷却到室温,氧又偏析到表面上。重新加热到650℃以上碳先从表面消失 关键词：     

Bi(Pb)-Sr-Ca-Cu-O(F)超导薄膜

本文介绍用电阻加热、单源混合分层蒸镀的方法制备掺 Pb 的 Bi-Sr-Ca-Cu-O(F)薄膜.我们用钼舟作加热源,用称量法控制膜的组份,采用金属 Bi、Pb、Cu 以及晶体 SrF_2和CaF_2 作原材料,把它们混合放入钼舟内加热蒸发.衬底为单晶 MgO(100).在热处理过程中通入湿氧和干氧,烧结温度850℃,获得了起始转变温度116K,零电阻温度103K 的超导薄膜.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.