Performance of a 2,4-DNPH coated annular denuder/HPLC system for formaldehyde monitoring in air

Summary The performance of annular denuders coated with 2,4-dinitrophenylhydrazine for collection of atmospheric HCHO has been evaluated by HPLC/UV analysis of samples coming from laboratory tests and field experiments. A number of parameters, such as collection efficiency at varying air humidity, detection limit, operative capacity and temporal self-consistency have been investigated to optimize the denuder behaviour under different weather conditions and to obtain short-term concentration profiles of HCHO. Deviations between measurements made simultaneously by the DNPH denuder method and differential optical absorption spectrometry (DOAS) have been found to average approximately 30% in the 0–5 ppb HCHO concentration range.     

Improved HPLC methodology in occupational exposure studies on formaldehyde

Summary This work describes an HPLC method for the determination of formaldehyde concentration in air. Traps containing 20–40 mesh silica gel coated with 2,4-dinitrophenylhydrazine (DNPH) are used. After aspiration of air the traps are eluted with methanol. The hydrazone formed is then separated on a C18 column using a mobile phase of methanolwater (50–50 v/v). The effluent is monitored with a UV detector at 365 nm. To calibrate and to compare this method with that of Niosh 2502 (traps coated with 2 benzylamino ethanol on Chromosorb 102), a mixing chamber that generated atmospheres of known concentration of formaldehyde was used.     

Development and comparison of different fluorimetric HPLC-methods with standard methods for the determination of formaldehyde in the atmosphere

Summary Three different fluorimetric methods for the measurement of atmospheric formaldehyde are described. The relatively unknown 2-diphenylacetylindan-1,3-dionhydrazine (DAIH) method was developed and optimized with an improved limit of detection of 2 ppbv corresponding to a sample volume of 7.5 L. Separation of lutidines necessary for the Nash method was successfully carried out and the separation time was reduced by a factor of 5. The detection limit of the Nash method was improved to 1 ppbv. In comparison, the N,N-diphenyl-1-naphthylamine-5-sulfonhydrazine (DNSH) method performed in a similar manner, reached an LOD of 0.5 ppbv. Finally, measurements made in candle smoke using the three different fluorimetric methods and three standard methods yielded very similar results.     

Development and validation of a liquid chromatography method for analysis of colistin sulphate

Summary The peptide antibiotic Colistin has been successfully separated into more than thirty components on a YMC-Pack Pro, C-18 column with a mobile phase of acetonitrile—sodium sulphate (0.7% m/v)—phosphoric acid (6.8% v/v dilution of 85% m/m H₃PO₄)—water (21.5∶50∶5∶23.5) at 1.0 mL per min and detection at 215 nm. Baseline resolution of the major components, colistin A and B, and many minor components was obtained. Robustness was evaluated by performing a full-factorial design experiment. The method showed good selectivity, repeatability, linearity and sensitivity.     

5(4)-Chloro-1-(2,4-dinitrophenyl)pyrazoles from 2,4-Dinitrophenylhydrazones of Chlorovinyl Ketones and β,β-Dichloroacrolein

A method has been developed for obtaining 3-alkyl(phenyl)-4(5)-chloro-1-(2,4-dinitrophenyl)pyrazoles from appropriate dinitrophenylhydrazones of 1-chloro-, 1,2-, and 2,2-dichlorovinyl ketones by heating the latter in polyphosphoric acid. The structure of the pyrazoles was studied by IR and ¹H NMR spectroscopy. __________ Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 7, pp. 1012–1019, July, 2005.     

Development and Validation of a Micellar Liquid Chromatographic Method with UV Detection for Determination of Azithromycin in Tablets and Capsules

A rapid and simple micellar liquid chromatographic method that does not require use of specific chromatographic columns has been developed and validated for azithromycin determination. The method uses a Hypersil C₁₈ column at 60 °C, 1-butanol–pH 6.86 phosphate buffer solution–water, 15:25:60 (v/v), containing 0.10 M sodium dodecyl sulfate, as mobile phase, and UV-detection at 215 nm. Different characteristics of the method were validated satisfactorily. The specificity, accuracy, linearity, precision (repeatability), and robustness of the method were demonstrated. The method proved suitable for determination of the azithromycin content of capsules and uncoated tablets.Revised: 5 February and 11 March 2004     

Ultra-high performance liquid chromatographic method for the determination of polycyclic aromatic hydrocarbons in a passive environmental sampler

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous compounds released in the environment by different sources. The aim of the present work was to validate a solid‐phase extraction (SPE) and a rapid ultra‐high performance liquid chromatographic (UHPLC) method for the analysis of PAHs in a passive environmental sampler, namely a Dacron® (the commercial name of a synthetic fiber based on polyethylene terephthalate) textile. The elution temperature was optimized to improve the resolution of early‐eluted compounds, namely acenaphthene (Ac) and fluorene (F). The UHPLC method lasts about 10 min and showed good linearity for all the 16 PAHs considered, with regression coefficients over 0.99. Recoveries, limits of detection (LODs), and limits of quantification (LOQs) of the SPE method were well within the performance criteria fixed by the Regulation n. 836/2011, namely 0.3 and 0.9 μg/kg, respectively.     

HPLC in photokinetics: Determination of reaction mechanism and photochemical quantum yields of (E)-1-phenylpropene

Summary A combined method of high-performance liquid chromatography and UV-absorption spectroscopy is described for use in dynamic systems. It provides a way of obtaining detailed mechanistic information as well as quantitative data (rate constants, quantum yields), even though neither mechanism nor photoproducts are known. The kinetic treatment of the photoreaction of (E)-1-phenylpropene was successful, showing a photo-isomerization and a parallel step. Information on this additional step is obtained by using HPLC to observe the changes in the concentrations of the reactants' selectivity. The necessity of process control is demonstrated.Dedicated to Prof. Ernst Bayer on the occasion of his 60^th anniversary.     

Development and Validation an LC Method for the Determination of Bendroflumethiazide in Human Plasma and its Pharmacokinetics

A simple, rapid, sensitive high performance liquid chromatography method with fluorescent detection was developed and validated for the determination of bendroflumethiazide in human plasma. Extraction from the plasma was by liquid-liquid extraction using ethyl acetate. Mosapride citrate was used as the internal standard. The chromatographic separation was performed on reverse phase LiChrosphere C18 column with mobile phase comprising of acetonitrile and phosphate buffer (38:62 v/v). The assay precision ranged from 0.9–12.5 and accuracy between 96.8–108.8%, revealing that the method has good reproducibility over the concentration range of 0.98–100.16 ng mL⁻¹. The validated method has been applied to analyze the bendroflumethiazide concentrations for application in pharmacokinetic, bioavailability or bioequivalence studies.     

Development of an Ion-pair HPLC method for the determination of 2,4- and 2,6-toluendiamine in human plasma

Summary An ion-pair HPLC method is presented for the determination in plasma of 2,4- and 2,6-toluendiamine (TDA), known carcinogens. The chromatographic conditions consisted in isocratic elution on a reversed phase C₁₈ column with 5 mM octanesulfonic acid in methanol-water, 45∶55, as mobile phase. UV detection was performed at 235 nm. Samples were analyzed after a simple single step liquid-liquid extraction and the method was validated by measurement of precision (interassay and intraassay), sensitivity, specificity, linearity, and recovery. The detection limit for both TDAs in plasma was 20 ng mL⁻¹. The correlation coefficients based on the intrassay calibration curve were 0.998 and 0.997 for 2,6- and 2,4-TDA, respectively. The intraassay accuracy, expressed in terms of recovery, was found to be up to 89.91% and 97.05% for 2,6- and 2,4-TDA, respectively.     

Development and Validation of an HPLC Method for Determination of Ceftiofur Sodium

An isocratic high-performance liquid chromatographic method has been developed for assay of ceftiofur sodium in drug substance and in sterile powder for injection. Chromatography was performed on a 250 mm × 4.6 mm, 5 μm particle, C₁₈ column with a 78:22 (v/v) mixture of 0.02 m disodium hydrogen phosphate buffer (pH adjusted to 6.0 with 85% orthophosphoric acid) and acetonitrile as mobile phase, at a flow rate of 1.0 mL min⁻¹. The separation was monitored by UV detection at 292 nm. Validation of the method for linearity and range, intra- and inter-day precision, accuracy, specificity, recovery, robustness, and limits of quantification and detection yielded good results. The calibration plot was linear from 20.0–120.0 μg mL⁻¹ and the correlation coefficient was 0.9999. It was shown that ceftiofur was degraded under acidic, alkaline, oxidative, and photolytic conditions. The method was found to be stability-indicating and could be used for routine analysis of ceftiofur sodium for injection.     

Determination and Validation of an LC Method for Fluvoxamine in Tablets

A new, simple, rapid and specific reversed-phase high-performance liquid chromatography (HPLC) method was developed and validated for the determination of fluvoxamine in pharmaceutical dosage forms. The HPLC separation was achieved on a C₁₈ μ-Bondapack column (250 mm × 4.6 mm) using a mobile phase of acetonitrile–water (80:20, v/v) at a flow rate of 1 mL min⁻¹. Proposed method is based on the derivatization of fluvoxamine with 1,2-naphthoquinone-4-sulphonic acid sodium salt (NQS) in borate buffer of pH 8.5 to yield a orange product. The HPLC method is based on measurement of the derivatized product using UV-visible absorbance detection at 450 nm. The method was validated for specificity, linearity, precision, accuracy, robustness. The degree of linearity of the calibration curves, the percent recoveries of fluvoxamine, the limit of detection and quantification, for the HPLC method were determined. The assay was linear over the concentration range of 45–145 ng mL⁻¹ (r = 0.9999). Limit of detection and quantification for fluvoxamine were 15 and 50 ng mL⁻¹, respectively. The results of the developed procedure (proposed method) for fluvoxamine content in tablets were compared with those by the official method. The method was found to be simple, specific, precise, accurate, reproducible and robust.     

Optimisation and validation of a generic method for the LC assay of six corticosteroids and salicylic acid in dermopharmaceutical forms

Summary A generic method was developed for the liquid chromatographic (LC) assay of six corticosteraids and salicylic acid in different dermatological formulations containing methylparaben and propylparaben or sorbic acid as preservatives. An adequate separation was obtained using octadecylsilica as stationary phase and a mixture of acetonitrile (MeCN) and 25 mM phosphate buffer of pH 3.5 as mobile phase. Segmented gradient elution was applied from 30 to 45% of MeCN in 9.9 minutes, then from 45 to 96% in 19.0 minutes. UV detection was performed at 240 nm. The method was validated. Very good results were obtained with respect to linearity, selectivity, precision and accuracy.     

Development of a highly sensitive method for determining atmospheric carbonyl compounds by passive sampling and application of the method to a survey of indoor air

A simple, highly sensitive analytical method for measuring many kinds of carbonyls in air using a passive sampler containing a sorbent (silica gel) coated with 2,4-dinitrophenylhydrazine has been developed. The carbonyls collected by the sampler were extracted with a solvent, and the extracts were subjected to high-performance liquid chromatography (HPLC; UV detection) without first being concentrated. In this method, the volume injection is examined, and is found to have a sensitivity at least 20 times that of ordinary HPLC methods. The air concentrations of nine carbonyls collected by passive sampling over a period of 24?h were estimated by means of conversion equations derived from the results of active sampling;c?=?^{10[log ( y} )^{??? b ] a} , where c is the carbonyl concentration in air (µg/m³); y is the amount of carbonyl collected by the passive sampler (µg); and a and b are constants for each carbonyl compound. The calculated air concentrations were consistent with the concentrations measured by active sampling. This method may be useful in determining personal exposure to ambient carbonyls.     

Development and Validation of a Liquid Chromatographic Method for Determination of Efavirenz in Human Plasma

A simple, rapid, and sensitive high-performance liquid chromatographic method for estimation of efavirenz in human plasma has been developed and validated. Chromatography was performed with C₁₈ analytical column and 50:50 acetonitrile–phosphate buffer (pH 3.5) as mobile phase. Compounds were monitored by UV detection at 247 nm. The retention time for efavirenz was 6.45 min and that for the internal standard, nelfinavir, was 2.042 min. Response was a linear over the concentration range of 0.1 μg–10 μg mL⁻¹ in human plasma. The method was simple, specific, precise and accurate and was useful for bioequivalence and pharmacokinetic studies of efavirenz.     

LC Determination of Gemfibrozil in Tablets

A simple, selective, precise and accurate reversed phase-HPLC assay for analysis of gemfibrozil in tablets was developed and validated. Separation and quantification were achieved on a Phenomenex C₁₈ column under isocratic conditions using a mobile phase (methanol:water, 80:20, v/v) maintained at 1.1 mL min⁻¹. UV-detection was at 280 nm. Atorvastatin was selected as an internal standard. The standard curves were linear over the range of 0.5–3.0 μg mL⁻¹ (r > 0.999). The limits of detection and quantification were 0.20 and 0.51 μg mL⁻¹, respectively. The recoveries for gemfibrozil were above 99.01%. The intra-day and inter-day precision (RSD) for gemfibrozil were below 1.74 and 1.83%, respectively. No chromatographic interferences from the tablet excipients were found. The results of the developed procedure in tablets were compared with those of the reference method to assess gemfibrozil content. Statistical comparison of the results with the reference method using spectrofluorimetric method showed excellent agreement and proved no significant difference in accuracy and precision. This HPLC method is fast and simple for the analysis of gemfibrozil in pharmaceutical preparations.     

Development of a Validated Stability-Indicating LC Method for Nitazoxanide in Pharmaceutical Formulations

A reversed-phase liquid chromatographic (LC) method was developed for the assay of nitazoxanide (NTZ) in solid dosage formulations. An isocratic LC separation was performed on a Phenomenex Synergi Fusion C₁₈ column (250 mm × 4.6 mm, i.d., 4 μm particle size) using a mobile phase of 0.1% o-phosphoric acid solution, pH 6.0: acetonitrile (45:55, v/v) at a flow rate of 1.0 mL min⁻¹. Detection was achieved with a photodiode array detector at 240 nm. The detector response for NTZ was linear over the concentration range from 2 to 100 μg mL⁻¹ (r = 0.9999). The specificity and stability-indicating capability of the method were proved using stress conditions. The RSD values for intra-day precision were less than 1.0% for tablets and powder for oral suspension. The RSD values for inter-day precision were 0.6 and 0.7% for tablets and powder for oral suspension. The accuracy was 100.4% (RSD = 1.8%) for tablets and 100.9% (RSD = 0.3%) for powder for oral suspension. The limits of quantitation and detection were 0.4 and 0.1 μg mL⁻¹. There was no interference of the excipients on the determination of the active pharmaceutical ingredient. The proposed method was precise, accurate, specific, and sensitive. It can be applied to the quantitative determination of drug in tablets and powder for oral suspension.     

Stress Degradation Studies on Tadalafil and Development of a Validated Stability-Indicating LC Assay for Bulk Drug and Pharmaceutical Dosage Form

A stability-indicating HPLC assay method was developed for the quantitative determination of tadalafil in bulk samples and in pharmaceutical dosage forms in the presence of the degradation products. It involved a 250 mm × 4.6 mm, 5 μm C-18 column. The gradient LC method employs solution A and B as mobile phase. Solution A contains a mixture of buffer (phosphate buffer and tetra-n-butyl ammonium hydrogen sulfate) pH 2.5: acetonitrile (80:20, v/v) and solution B contains a mixture of water: acetonitrile (20:80, v/v). The flow rate was 1.0 mL min⁻¹ and the detection wavelength was 220 nm. The retention time of tadalafil is about 17 min. Tadalafil was subjected to different ICH prescribed stress conditions. Degradation was found to occur in hydrolytic and to some extent in oxidative stress conditions, while the drug was stable to photolytic and thermal stress. The drug was particularly labile under alkaline hydrolytic conditions. The drug was subjected to stress conditions of hydrolysis, oxidation, photolysis and thermal degradation. The assay of stress samples was calculated against a qualified reference standard and the mass balance was close to 99.5%. The developed RP-LC method was validated with respect to linearity, accuracy, precision and ruggedness.     

A chemical potential driven micro-membrane sampler and its application for the determination of trace carbonyl compounds in air

A chemical potential driven micro-membrane sampler for enrichment of trace gaseous carbonyl compounds has been developed. The sampler is composed of exposed parts with membrane and analysis parts with polypropylene tube. The membrane acts as a barrier, through which the analytes dynamically diffuse and transfer from absorbents present outside to extract solvent inside through the difference of chemical potential. Formaldehyde and acetic acid were selected as verification samples. Quantification is achieved through high performance liquid chromatography (HPLC) analysis. The mass of analytes determined shows a linear correlation with concentration of the gaseous analytes. The limits of detection of formaldehyde and acetic acid after 8 h sampling were 3.32 and 0.76 μg m⁻³.     

A Stability-Indicating LC Method for the Simultaneous Determination of Telmisartan and Ramipril in Dosage Form

A simple, rapid, and precise method is developed for the quantitative simultaneous estimation of telmisartan and ramipril in combined pharmaceutical dosage form. A chromatographic separation of the two drugs was achieved with an ACE 5 C₁₈, 25-cm analytical column using buffer–acetonitrile (55:45 v/v). The buffer used in mobile phase contains 0.1 M sodium perchlorate monohydrate in double distilled water pH adjusted 3.0 with trifluoroacetic acid. The instrumental settings are flow rate of 1.5 mL min⁻¹, column temperature at 30 °C, and detector wavelength of 215 nm using a photodiode array detector. The resolution between ramipril and telmisartan were found to be more than 5. Theoretical plates for ramipril and telmisartan were 13,022 and 6,629. Tailing factor for ramipril and telmisartan was 0.94 and 0.98. Telmisartan, ramipril and their combination drug product were exposed to thermal, photolytic, hydrolytic and oxidative stress conditions, and the stressed samples were analysed by the proposed method. Peak homogeneity data of telmisartan and ramipril is obtained using photodiode array detector, in the stressed sample chromatograms, demonstrated the specificity of the method for their estimation in presence of degradants. The described method shows excellent linearity over a range of 20–400 μg mL⁻¹ for telmisartan and 2.5–50 μg mL⁻¹ for ramipril. The correlation coefficient for telmisartan and ramipril are 1. The relative standard deviation for six measurements in two sets of each drug in tablets was always less than 2%. The proposed method was found to be suitable and accurate for quantitative determination and the stability study of telmisartan and ramipril in pharmaceutical preparations.