Spectrophotometric determination of silicate with Rhodamine B by flow-injection analysis

A spectrophotometric flow-injection method for the determination of silicate based on the formation of an ion pair between molybdosilicic acid and Rhodamine B is proposed. It allows silicate to be determined over the concentration range 0.17–2.0 mg 1^?1 at a sampling rate of 40 h^?1, is reasonably precise and is highly tolerant to ions that commonly occur in waters. It has been applied with satisfactory results to the determination of silicate in various types of water.     

Spectrophotometric determination of tungsten with thiocyanate

The yellow W(V) thiocyanate complex is formed by shaking sodium tungstate solution in 0.2-0.8M potassium thiocyanate and 4-5M hydrochloric acid, with mercury. It is extracted with 2% tribenzylamine solution in chloroform and measured at 410 nm. U, Ti, V, Cr, Fe, Co, Ni, Mn, Al, Pb, Sn, Bi, Pd, Sb and Cu do not interfere. Pt and Mo in amount equal to that of tungsten give errors of up to 0.4 and 2% respectively. The sensitivity is 0.013 mug ml and Beer's law is obeyed up to 24 mug ml .     

Spectrophotometric determination of uranium in sea water with thiocyanate and rhodamine B

Summary Spectrophotometric Determination of Uranium in Sea-Water with Thiocyanate and Rhodamine B In the presence of a large excess of thiocyanate uranium(VI) forms a violet colour with Rhodamine B. The complex can be stabilized by addition of poly (vinyl alcohol). The calibration graph for measurement at 600 nm is linear in the range 0.5–10g of uranium per 25ml, the molar absorptivity being 3.56×10⁵1-mole^–1·cm^–1. The effect of foreign ions has been studied and the method can be applied to the determination of uranium in sea-water, with reliable results. Uranium is preconcentrated from sea-water by a flotation procedure with toluene in presence of benzoate and Safranine T, with nitrilotriacetic acid as masking agent. The method is highly selective for uranium, with a recovery of 97.9–99.2%.     

Spectrophotometric determination of osmium with ammonium thiocyanate

Summary A spectrophotometric method for the determination of osmium using ammonium thiocyanate is described. A stable reddish brown colour with an absorption maximum at 440 nm is produced when osmium tetroxide is heated for 30 min at a p_H between 1 to 4 over a boiling water bath with excess reagent. The recommended concentration range is from 3 to 15 ppm of osmium in aqueous medium and from 0.6 to 1.5 ppm when the brown colour (which turns blue) is extracted into isoamyl alcohol. Errors are about ± 1.5%.

---

Zusammenfassung Zur spektrophotometrischen Bestimmung von Osmium wird als Reagens Ammoniumthiocyanat empfohlen. Bei Erwärmung von Osmiumtetroxid bei p_H 1–4 mit überschüssigem Reagens (30 min) wird eine beständige rötlich-braune Färbung mit einem Absorptionsmaximum bei 440 nm gebildet. Der günstigste Konzentrationsbereich ist 3–15 ppm in wä\rigem Medium bzw. 0,6–1,5 ppm, wenn mit Isoamylalkohol extrahiert wird (wobei die Farbe nach Blau umschlägt). Die Fehler betragen etwa ± 1,5%.

     

Spectrophotometric determination of micro amounts of thiosulfate by liberation of thiocyanate from mercury(II) thiocyanate

The proposed determination of thiosulfate is based on the liberation of thiocyanate by the reaction of thiosulfate with mercury(II) thiocyanate and spectrophotometric determination of the thiocyanate with iron(III). The reaction of thiosulfate with mercury(II) thiocyanate is elucidated with reference to a system containing phosphate buffer; the phosphate is shown to participate directly in the reaction, and a balanced chemical equation is given. Optimum conditions are described for the stoichiometric formation of 3 mol of thiocyanate from 1 mol of thiosulfate. The method can be applied to the determination of thiosulfate in the range 3 × 10^?6–1.4 × 10^?4 M (1.7–78.5 μg thiosulfate in 5 ml).     

Spectrophotometric determination of trace amounts of cadmium and lead with iodide and Rhodamine B

Summary Highly sensitive spectrophotometric methods have been developed for determination of cadmium and lead, based on the CdI₄ ^2– or PbI₄ ^–2 anionic complexes with Rhodamine B in the presence of polyvinyl alcohol to form ion-association complexes. The molar absorptivity is 4.2×10⁵l·mole^–1·cm^–1 at 600 nm for cadmium and 5.7×10⁵l·mole^–1·cm^–1 at 610 nm for lead. The complexes have the composition [CdI₄ ^2–]·[RhB⁺]₂ and [PbI₄ ^2–]·[RhB⁺]₂ as established by Job's method of continuous variations and the molarratio method. The colour reaction selectivity is fairly good and the method can be applied for direct spectrophotometric determination of cadmium or lead in some pure metals. A species [PbI₃ ^–]·[RhB⁺] can also be formed, and extracted into toluene or a toluene/diethyl ether mixture.

---

Spektrophotometriscbe Bestimmung von Spuren Cadmium und Blei mit Jodid und Rhodamin B

Zusammenfassung Hochempfindliche spektrophotometrische Methoden für die Bestimmung von Cadmium und Blei wurden entwickelt; sie beruhen auf der Reaktion von CdJ₄ ^2– bzw. PbJ₄ ^2– mit Rhodamin B in Gegenwart von Polyvinylalkohol unter Bildung von Ionenassoziat-Komplexen. Die molare Absorptivität für Cadmium beträgt 4,2×10⁵l·mol^–1·cm^–1 bei 600 nm und für Blei 5,7×10⁵l·mol^–1·cm^–1 bei 610 nm. Wie nach der Methode der kontinuierlichen Variation nach Job bzw. mittels Molarverhältnis ermittelt wurde, lautet die Formel [CdJ₄] [RhB]₂ bzw. [PbJ₄] [RhB]₂. Die Selektivität der Farbreaktion ist gut. Das Verfahren kann zur direkten spektrophotometrischen Bestimmung von Cadmium bzw. Blei in verschiedenen reinen Metallen verwendet werden. Auch eine Verbindung [PbJ₃ ^–] [RhB⁺] kann hergestellt werden, die sich mit Toluol oder mit einem Gemisch aus Toluol und Diethylether extrahieren läßt.

     

Spectrophotometric determination of molybdenum in rocks with thiocyanate

A rapid procedure for the determination of microgram amounts of molybdenum in rocks is described. After acid decomposition, molybdenum is extracted from a hydrochloric acid solution into xylene with tributyl phosphate. After back-extraction with water, molybdenum is extracted as the α-benzoinoximate into chloroform, stripped into hydrochloric acid extracted as the thiocyanate into amyl alcohol, and determined spectrophotometrically. The molybdenum thiocyanate color produced is stable, sensitive, and reproducible. Results of analyses of several of the U.S. Geological Survey standard rocks are given.     

Spectrophotometric determination of chloride in non-polar media by the mercury(II) thiocyanate reaction

A simple, rapid and accurate method for the spectrophotometric determination of chloride in non-polar media is described. The method is based on the well-known reaction of mercury(II) thiocyanate with chloride to release thiocyanate, which then reacts with iron(III). The optimum concentrations of reagents for the determination of chloride in 2,2,4-trimethylpentane (iso-octane) and cyclohexane are reported. The molar absorptivity of the complex at 505 nm is 5120 ± 200 dm³ mol^?1 cm^?1 for iso-octane and 5340 ± 340 dm³ mol^?1 cm^?1 for cyclohexane. Beer's Law is obeyed in the range 2 × 10^?7–2 × 10^?5 mol dm^?3 (0.01–1 mg l^?1) chloride.     

Spectrophotometric Determination of Trace Ruthenium with Molybdate and Ethyl Rhodamine B

Spectrophotometric determination of trace Ru(Ⅲ) with molybdate had been reported by references. Its sensitivity is much better. However, the colour reaction of ion-association complex of Ru(Ⅲ)-molybdate-rhodamine B(ERB) system has not been reported till now.     

Spectrophotometric determination of thiocyanate ions in stratal waters

The formation of [FeSCN]²⁺ complex in hydrochloric and sulfuric acid medium was studied by spectrophotometry using iron(III) sulfate and ammonium iron(III) sulfate solutions as reactants. A method for the determination of 10–200 μg SCN^? in 25 mL water solutions containing ammonium iron(III) sulfate in sulfuric acid medium was developed; its determination limit is 2.6 μg (P = 0.99, n = 9). The method was applied for the analysis of model water samples with macro- and micro-component compositions similar to that of water from the Arigol licensed area. Operational control of the accuracy rate was performed by the standard addition method. The developed method can be applied to analyze water samples containing 1–90 mg/L thiocyanate ions.     

用钼酸盐和罗丹明B连续光度法测定铈和钪

聚乙烯醇存在下，铈或钪钼杂多酸与罗丹明Ｂ（ＲＢ）形成离子缔合物，最大吸收均位于５７０ｎｍ，摩尔吸光系数分别为１．１６×１０＾６和５．６２×１０＾５Ｌ．ｍｏｌ＾－１．ｃｍ＾－１，ｃｍ＾－１，０－１．２μｇ／２５ｍＬＣｅ和０－２．０μｇ／ｍＬＳｃ服从比耳定律，检测限１．５ｎｇ／ｍＬＣｅ（ｎ＝１０）和１．１ｎｇ／ｍＬＳｃ（ｎ＝９）。缔合物的摩尔比为Ｃｅ：ｍＯ：ＲＢ＝１：６：３和 Ｓｃ：Ｍｏ：ＲＢ＝１：１     

Selective complexometric determination of mercury with thiocyanate as masking agent

A method is proposed for selective complexometrie determination of mercury, thiocyanate being used as masking agent. An excess of EDTA is added and the surplus is back-titrated at pH 5-6 with lead nitrate, Xylenol Orange or Methylthymol Blue being used as indicator. Thiocyanate is then added to decompose the mercury-EDTA complex and the liberated EDTA is titrated with lead nitrate. The interference of various cations has been studied.     

罗丹明B-硫氰酸盐分光光度法测定微量金

本文研究了Au(Ⅲ)-KSCN-罗丹明B-阿拉伯树胶水相显色体系和光度特性。缔合物的λ_(max)为595nm,表现摩尔吸光系数ε=1.23×10~5L mol~(-1).cm~(-1).Au(Ⅲ)浓度在0.0～8.0μg/25mL时服从比耳定律。所制定的测金光度法,结合巯基棉分离技术,已试用于金精矿的分析,获得了较好结果     

Spectrophotometric determination of mercury in soils with triphenyltetrazolium chloride

The formation of the acidocomplex of mercury(II) with triphenyl-tetrazolium chloride is studied spectrophotometrically in water-organic media. The composition of the complex is established as TTC:Hg:I = 1:1:1. The molar absorptivity (255) = (6.45 +/- 0.12) x 10(4) 1 mole(-1). cm(-1) is determined. The selectivity of the reaction is studied and the method for determination of mercury(II) 0.1-0.8 mug/ml is shown. Extraction investigations of the system discussed were carried out. The characteristic values for the extraction equilibrium and the equilibrium in the aqueous phase was determined: extraction constant K(ex) = 3.16 x 10(4), distribution constant K(D) = 20.67, and association constant = 1.53 x 10(3). 5 A rapid and sensitive extractive-photometric method for determination of mercury(II) in soil was developed. The determination was carried out without preliminary elimination of mercury.     

Spectrophotometric determination of thiocyanate via coprecipitation and thermal decomposition of copper(I) thiocyanate

A method for determination of thiocyanate (6–100 μg described. It is based on the coprecipitation of copper(I) thiocyanate with copper(I) iodide, followed by decomposition of copper(I) thiocyanate in air at 450°C. The decomposition products are CuS, CuO, SO₂, CO₂ and N₂. Released sulphur dioxide is absorbed in sodium tetrachloromercurate(II) solution, and determined spectrophotometrically with bleached p-rosaniline. The method is unaffected by the presence of halides, sulphide, sulphite and thiosulphate.     

Spectrophotometric determination of mercury(II) with sodium sulfite

A photometric procedure is developed for determining mercury(II) in aqueous media. It is based on the reaction of mercury(II) with sodium sulfite giving a product with an absorption maximum at 230 nm. The optimum conditions are found. The procedure allowed 0.5 to 13.0 μg/mL of mercury(II) to be determined for 1 min. The effect of some metal cations is estimated.     

Spectrophotometric determination of molybdenum with thiocyanate after extraction of the tetraphenylarsonium and tetraphenylphosphonium complexes

Microchimica Acta - Spectrophotometric determination of molybdenum with thiocyanate by extraction of the tetraphenylarsonium and tetraphenylphosphonium ion-association complexes is described....     

Spectrophotometric determination of zirconium with 5,7-dibromo-8-hydroxyquinoline in presence of thiocyanate

The characteristics of the ternary complex formed between zirconium(IV) and 5,7-dibromo-8-hydroxyquinoline in presence of thiocyanate have been studied with an analytical point of view. The resulting colored species is extractable into chloroform with absorption maximum at 416 nm, which leads to the determination of the trace amounts of the metal ion. The method obeys Beer’s law in the range 0.2–9.0 μg Zr/mL having molar absorbitivity and Sandell’s sensitivity values of 1.05 × 10⁴ L/mol cm and 0.0087 μg Zr/cm², respectively. The ratio of zirconium(IV), 5,7-dibromo-8-hydroxyquinoline and thiocyanate in the extracted species is found to be 1: 2: 2. A large number of foreign ions do not interfere in the proposed method. The applicability of the procedure is tested by carrying out satisfactorily the analysis of a wide variety of samples.