偶氮苯聚合物全息光栅衍射效率和偏振特性研究

研究了不同偏振全息模式下基于交联偶氮苯聚合物薄膜的相位光栅的形成机理、衍射效率和偏振特性.利用琼斯矢量表征了正交线偏振(SP)和半行线偏振(SS)干涉模式下的偏振干涉场.基于SP和SS两种模式,制作了无明显表成起伏的纯折射率光栅和有表面起伏的浮雕光栅.偏光显微镜(POM)观测说明纯折射率光栅具有周期性的折射率分布;近场光学显微镜(SNOM)探测说明纯折射率光栅和浮雕光栅的表而起伏在5 nm以下和 85.23 nm.实验表明.当探测光为水平偏振时,纯折射率光栅的衍射效率达到22.2%.浮雕光栅只能达到1.65%.纯折射率光栅的0、 1级衍射光分别为水平和竖直线偏振光,偏振度达到0.9969和0.9963;浮雕光栅的0, 1级衍射光均为水平线偏振光.     

Poled polymer thin-film gratings studied with far-field optical diffraction and second-harmonic near-field microscopy

Electrical poling induces polar ordering of molecules in a grating that has been holographically inscribed on a thin film of polymer with azobenzene side chains. The resulting chi2 grating, seen by second-harmonic-generation (SHG) near-field scanning optical microscopy, can have a periodic structure that is significantly different from the topographical image. The far-field linear and SHG diffration patterns correlate well with the grating structures. Poling of the thin-film grating, which presumably has photodriven nonuniform material properties within each period, leads to the more complex structure of the chi2 grating.     

Experimental study of liquid-crystal alignment on a surface relief grating

In this experimental work, photofabrication of a surface relief grating (SRG) on poly[(methyl-methacrylate)-co-(DR1 methacrylate)] copolymer was used align liquid-crystal molecules in parallel. The interference pattern of circularly polarized Ar⁺ laser beams was used for this purpose, and the dynamic diffraction efficiency of the grating was measured at the same time. Then, the polymeric layers aligned by SRG were used to fabricate a homogeneous aligned liquid-crystal cell. The SRG-induced optical anisotropy of the empty cell and the cell filled with the well-known 5CB nematic liquid crystal was investigated by polarizing microscopy. In addition, the SRG-induced dichroism was studied by polarized UV-Vis spectrophotometry. Finally, the SRG-induced dichroism and optical anisotropy were compared for four different incidence angles. This alignment technique could have useful applications in in-plane switching LC displays.     

Feasibility analysis of solid immersion lens-based dual-layer near-field recording optics with a numerical aperture of 1.84

A dual-layer near-field recording (NFR) optical system with a high numerical aperture (NA) of 1.84 was designed by appropriate cover and spacing layer selection, using layers with refractive indices of 2.0. The designed aplanatic imaging optics exhibited additional aberrations in the multi-layered stack, mainly due to the air-gap and spacer layer. Given optics designed only to compensate for aberrations caused by a 2-μm-thick cover-layer, a 3-μm-thick spacer layer induces 96.2 mλ_rms and 6.5 mλ_rms of spherical aberration and defocus, respectively. A complete electric field calculation analysis for the inside of the multi-layer stack verified that diffraction-limited spot quality can be ensured on the recording layer with phase-only correction. As the aberration caused by the multi-layered stack cannot be corrected perfectly, due to the high oscillation of the aberration function along the radial direction in the exit pupil, three different types of liquid crystal (LC) electrodes were considered for practical implementation. Of the three phase-correction methods, the approximate linear phase-correction method was the most tolerant of axis decenter from the optical axis, providing acceptable diffraction-limited correction performance.     

Artificial control of 2D ZnO patterns using interference patterning of photodynamic polymer

A facile and economic approach was demonstrated for the artificial control of the grating period in 2D ZnO nanostructures. Highly-ordered ZnO nanostructures with various periodicities (e.g., 0.5, 1.0, 1.5, and 2.0 μm) were prepared through a combination of a controlled Ar⁺ laser interference process on a PDO3 film and spin-coating technique utilizing aqueous zinc acetate/polyvinyl alcohol (PVA) solution, which obviate the need for costly and complex processes such as a chemical etching step. The grating periods of the resulting 2D ZnO arrays are well matched with those of the photodynamically manipulated 2D surface relief grating (SRG) structure of the polymeric templates. The optical properties of 2D ZnO nanostructures with various widths and spatial densities were explored.     

新型聚偶氮苯取向增强光折变效应及全息存储

合成了新型偶氮分子偶氮二苯胺ADPA(Azo-diphenylamine),将其掺入聚乙烯咔唑Poly(N-Vinylcarba-zole)(PVK)和聚丙烯丁酯(Poly-butylacrylate)(PBA)的聚合物(PVK-PBA)以及三硝基芴酮2,4,7-trinitro-9-flu-orenone(TNF)聚合制成薄膜器件。结果表明掺杂偶氮苯聚合物薄膜在非共振吸收下具有强的光致取向增强光折变效应。光致折射率变化值Δn达到1.3×10-3以上。样品在两相干光束作用下,可建立光折射率光栅,其衍射效率可超过30%,实现了光全息存储。讨论了影响折射率光栅的因素,并对全息存储相关结果形成的机制进行了分析。     

Optical Storage Media with Dye-Doped Minute Spheres on Polymer Films

We have fabricated a new optical storage media using minute spheres arranged on a surface relief grating (SRG). Using minute spheres as recording bits, we can limit recordable regions by sphere size, and can realize high resolution reproduction in the plane direction. Surface relief structures were made on a polymer thin film on which we performed diffusion arrangement and adsorptive fixation of minute spheres. The stability of the arranged spheres was confirmed for heating and washing. Furthermore, we used a dipping method for a more simple arrangement of minute spheres on a large area of the substrate and made a monolayer sample of the spheres. We were able to realize a highly sensitive reconstruction of the medium using a confocal optical system as a record and readout system.     

UV beam-assisted efficient formation of surface relief grating on azobenzene polymers

An efficient method is demonstrated to improve the formation of a surface relief grating (SRG) with a high amplitude. The SRG is realized by a two-beam interference technique (λ=532 nm) in an azobenzene side-chain copolymer. An UV laser beam (λ=355 nm), called assisting beam, was used to accelerate the photoisomerization process from cis-form to trans-form, resulting in a rapid cis-form ? trans-form cycle. This UV beam-assisted method allowed to increase the diffraction efficiency of the formed SRG as well as its depth. Stable gratings with modulation depth as high as 410 nm were obtained at room temperature with moderate laser power.     

Diffraction efficiency increase by corona discharge in photoinduced surface-relief gratings on an azo polymer film

The diffraction efficiency of a surface-relief grating (SRG) was dramatically increased by corona discharge. We fabricated this SRG by applying surface modulation to azo polymer films, using laser interference fringes. The electric charge was deposited upon the SRG by a corona discharge in an oven. The first-order diffraction efficiency measured before and after corona discharge above the glass-transition temperature increased from ~2% to ~40% in a SRG written with a circularly polarized beam. The relief depth of the SRG as measured with an atomic-force microscope also increased, from ~130 nm to ~450 nm. The increase in diffraction efficiency was independent of the writing polarization.     

偶氮液晶聚合物薄膜的二维偏振全息记录

利用偏振全息记录的方法在一种含偶氮侧链的液晶聚合物薄膜中写入了二维偏振光栅.实验采用两束正交偏振的532 nm线偏光作为写入光,在样品同一点上分别记录了相互垂直的两个一维偏振光栅,继而对所构成的二维偏振光栅的特性进行了研究.实验结果表明：二维光栅的衍射效率比一维光栅低,其偏振特性是两个一维光栅元特性的叠加;二维光栅衍射效率对入射光偏振态的依赖性和光栅的偏振转换性质来源于材料中线双折射和圆双折射的共同作用. 关键词： 偏振全息 二维光栅 偶氮液晶聚合物     

Enhanced broadband optical transmission in metallized woodpiles

We present an optimized isotropic metal deposition technique used for covering three-dimensional polymer structures with a 50 nm smooth silver layer. The technology allows fast and isotropic coating of complex 3D dielectric structures with thin silver layers. Transmission measurements of 3D metallized woodpiles reveal a new phenomenon of enhanced optical transmission in broadband range (up to 300 nm) in the near IR.     

Effective optical constants and effective optical properties of ultrathin trilayer structures

This work presents an extension of the characteristic effective medium approximation (CEMA) to ultrathin trilayer systems. The extension has been carried out analytically and is supported by corresponding calculations of the effective optical constants of Cu-Au-Cu and Ag-SiO-Ag trilayer systems using the CEMA approximation. This work is in essence a generalization of the characteristic effective medium approximation introduced earlier for ultrathin bilayer structures. This method is used to derive the effective optical constants of a trilayer system, consisting of three thin layers with each constituent layer of thickness much less than the wavelength of the incident radiation. Within this regime a trilayer system is viewed as one effective layer referred to as an effective stack (ES) with well defined effective optical constants, which can be used to calculate the optical properties of the trilayer stack within a specified wavelength range. The CEMA based calculations of the effective optical constants are applied to two trilayer systems with a total of five stacks. Three are Cu-Au-Cu and two are Ag-SiO-Ag stacks. The thicknesses of the parent layers in the Cu-Au-Cu stack range from 3 to 30 nm for Cu and 4 to 40 nm for Au; in the Ag-SiO-Ag stack the constituent layers are 6 nm for Ag, but range from 5 to 10 nm for SiO. This study is for normal or near normal incidence spectroscopy in a wavelength range that extends from visible to near infrared. The agreement between CEMA based ES stack results and those of the standard CMT technique is very satisfactory.     

在聚合物表面刻写方格子的新方法及理论研究

为了提高制作偶氮苯微结构的实验技术,在偶氮苯聚合物的光致异构和光致取向特性的基础上,利用两激光束的新实验方案,运用比较简便的分步制作的方法,成功的在偶氮苯功能化聚合物薄膜表面“刻写”出二维的正方格子结构。提出了一个新的光异构取向场理论：在两束偏振方向互相垂直的偏振光照射下,偶氮苯聚合物表面光栅的形成是光异构取向场的干涉的结果,并对实验现象进行了解释。用计算机对实验结果进行了模拟,将模拟结果与实验结果进行了比较,结果表明计算机模拟将会更加有利于偶氮苯聚合物微结构的设计和制作。     

Fabrication of optical devices in poly(dimethylsiloxane) by proton microbeam

Optical diffraction grating and micro Fresnel zone plate type structures were fabricated in relatively thin poly(dimethylsiloxane) (PDMS) layers using proton beam writing technique and the performance of these optical devices was tested. PDMS is a commonly used silicon-based organic polymer, optically clear, generally considered to be inert, non-toxic and biocompatible. PDMS has been used as a resist material for direct-write techniques only in very few cases. In this work, PDMS was used as a resist material; the structures were irradiated directly into the polymer. We were looking for a biocompatible, micropatternable polymer in which the chemical structure changes significantly due to proton beam exposure making the polymer capable of proton beam writing. We demonstrated that the change in the structure of the polymer is so significant that there is no need to perform any development processes. The proton irradiation causes refractive index change in the polymer, so diffraction gratings and other optical devices like Fresnel zone plates can be fabricated in this way. The observed high order diffraction patterns prove the high quality of the created optical devices.     

Spatial light modulation with an azobenzene-doped polymer by use of biphotonic holography

Spatial light modulation by use of a biphotonic holographic grating has been demonstrated in an azobenzene-doped polymer film. The mechanism of incoherent-to-coherent optical conversion originates from the photoinduced trans <--> cis isomerization of azobenzene molecules by two color lights. It is also found that when the intensity of the blue beam is varied the output replica of the input information changes sign.     

Broadband light emitting from multilayer-stacked InAs/GaAs quantum dots

We report the effect of the GaAs spacer layer thickness on the photoluminescence(PL) spectral bandwidth of InAs/GaAs self-assembled quantum dots(QDs).A PL spectral bandwidth of 158 nm is achieved with a five-layer stack of InAs QDs which has a 11-nm thick GaAs spacer layer.We investigate the optical and the structural properties of the multilayer-stacked InAs/GaAs QDs with different GaAs spacer layer thicknesses.The results show that the spacer thickness is a key parameter affecting the multi-stacked InAs/GaAs QDs for wide-spectrum emission.     

Volume structuring of high power LED encapsulates by femtosecond laser direct writing

We report on the micro-fabrication of diffractive optical elements (DOEs) such as 1D, 2D and concentric grating structures inside the volume of thin silicone films by femtosecond laser direct writing. In addition, we show that such structures can also be integrated into silicone films that act as encapsulation layers of high power light-emitting diodes. The latter strategy opens new possibilities to homogenize and to control the light emitted from such devices.     

Dipolar coupling effect in magnetic bilayer system

Equilibrium micromagnetic structures in a bilayer system composed of two thin cobalt films separated by a non magnetic spacer are systematically analysed. These 2D magnetization distributions are obtained by numerical computations according to different set of magnetic and geometric parameters. The coupling effect due to the dipolar long range interaction (or stray-field effect) between the two Co layers is studied through the evolution of the magnetic pattern in the stack with or without an applied field and compared to a continuous film of same thickness. Special attention is paid to the hysteresis process in a bilayer. Even though the general aspect of the magnetization distribution looks like a Landau-Lifshitz structure, the absence of any core in the vortex of the magnetic structure is analysed in relation to a possible disappearence of (topological) hysteresis. Received 12 December 2001     

Simultaneous process of embossing and poling at elevated temperatures: a simple technique for nonlinear grating formation in polymer films

A simple technique for fabrication of nonlinear gratings in polymer films, based on simultaneous embossing and poling, is proposed and demonstrated. A master grating consisting of a metal electrode with a dielectric die was fabricated and used for repeated embossing of the grating structures into nonlinear optical polymers at elevated temperatures. At the same time, we applied high voltage to the polymer films to induce second-order nonlinearity. The grating profile and the nonlinearity were estimated, as well as the mass productivity of nonlinear gratings.     

Optical properties of vertically aligned self-assembled InGaAs quantum dot layers on (311)A/B and (100) GaAs substrates

In this work, we present substrate orientation effects on optical properties in vertically stacked In_0.5Ga_0.5As layers grown by molecular beam epitaxy on (311)A/B and reference (100) GaAs substrates. Samples were grown for different GaAs spacer thicknesses. The spacer thickness variation shows the influence on PL spectra for all planes. The differences in peak shape, peak position, amplitude and integrated luminescence have been observed for all surfaces. These differences suggest that indium migration in spacer layers is caused by the strain fields induced by islands buried below, and is different at the three surfaces. Vertical electronic coupling between quantum dots is confirmed by photoluminescence temperature dependence.