表面水热碳层对磁性NiFe2O4八面体光催化活性的影响

采用葡萄糖水热碳化法合成了一系列碳层包覆的NiFe₂O₄核壳八面体(NiFe₂O₄@C). 通过调控葡萄糖的含量可以有效控制NiFe₂O₄表面包覆的碳层厚度. 利用X射线衍射(XRD)、 拉曼光谱(Roman)、 X射线光电子能谱(XPS)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)和紫外-可见漫反射光谱(UV-Vis DRS)等对NiFe₂O₄@C的组成、 结构、 形貌和光学性能进行了表征. 考察了表面水热碳层对NiFe₂O₄光催化降解亚甲基蓝(MB)性能的影响. 结果表明, NiFe₂O₄的光催化活性很大程度上依赖于在其表面包覆的碳层厚度, 碳层厚度为5.5 nm的NiFe₂O₄@C-3展现了最佳的光催化活性. 荧光光谱(PL)、 瞬态光电流和电化学阻抗谱(EIS)表征结果证明, NiFe₂O₄@C的光催化性能的提升归因于在NiFe₂O₄核和碳壳之间形成了异质结, 有效地促进了光生载流子的传输和分离效率. NiFe₂O₄@C复合材料展现了较好的稳定性和可回收性, 在污水处理方面有很大的应用潜力.     

磁性纳米TiO2/Fe3O4光催化复合材料的制备及性能

采用溶胶-凝胶法，在磁性Fe3O4表面包覆TiO2，制备了一种新型纳米TiO2/Fe3O4光催化复合材料．XRD，TEM对材料形态结构及包覆情况的分析，显示TiO2包覆在Fe3O4表面，形成平均尺寸为35～50nm的复合结构；UV-vis吸收曲线表明，复合材料对光的吸收出现红移，吸收强度增大；对染料废水光催化降解的模拟研究表明，该复合材料对活性艳红染料的脱色率达100％，是一种便于回收、可重复使用的高效光催化剂．     

磁性树脂基复合材料的研究进展

综合磁性树脂基复合材料的研究现状,着重介绍了磁性树脂基复合材料的三大类：粘结磁体、磁性高分子微球和磁性离子交换树脂的最新发展和研究状况。     

磁性AgBr/Ag3PO4/ZnFe2O4复合催化剂的制备及光催化性能

水热法结合原位沉淀法成功制备新型磁性溴化银/磷酸银/铁酸锌(AgBr/Ag₃PO₄/ZnFe₂O₄)复合催化剂,并通过X射线衍射、能量色散X射线、场发射扫描电子显微镜、透射电子显微镜和紫外-可见漫反射光谱对其晶相结构、组成、形貌及吸光性能进行了表征。在可见光照射下,所制备的AgBr/Ag₃PO₄/ZnFe₂O₄复合催化剂光催化降解罗丹明B (RhB)的活性优于Ag3PO4/ZnFe₂O₄、AgBr/ZnFe₂O₄和P25 TiO₂。在酸性和碱性溶液中,AgBr/Ag₃PO₄/ZnFe₂O₄光催化剂呈现出优良光催化性能。在AgBr/Ag₃PO₄/ZnFe₂O₄体系中,光催化降解RhB的速率随着反应体系温度的升高而增大,由阿伦尼乌斯方程计算获得反应体系活化能为31.9 kJ·mol^-1。AgBr/Ag₃PO₄/ZnFe₂O₄复合材料优异的可见光催化活性归因于光生电荷的有效分离,所产生的超氧自由基和空穴是RhB降解的主要活性物种。     

磁性纳米固体酸SO4^2ˉ-TiO2-Fe3O4催化剂的合成、表征及催化性能的研究

首先研究制备了Fe3O4和SO4^2ˉ-TiO2固体酸催化剂，在此基础上采用共沉淀和浸渍的方法制备了磁性和超细SO4^2ˉ-TiO2-Fe3O4固体酸催化剂。利用XRD，TEM和FT—IR等分析测试手段对催化剂的结构和性能进行了表征。测定结果证实该催化剂具有较小的粒度，较高的磁性表现。在乙酸丁酯合成反应中SO4^2ˉ-TiO2-Fe3O4展示了很高的催化活性（酯化率可达82．7％），而且利用Fe3O4的磁性可对催化剂进行分离和回收．     

新型磁性荧光Fe3O4-CdSe纳米复合材料的制备

以1-十八烯作为高沸点溶剂, 在磁性粒子表面沉积量子点获得新型的磁性荧光Fe₃O₄-CdSe 纳米异质结构. 首先以乙酰丙酮铁(Fe(acac)₃)为前驱体, 二苯醚为溶剂, 油酸为表面活性剂和油胺(OAm)为表面活性剂兼还原剂, 通过溶剂热法制备单分散性的Fe₃O₄ 纳米粒子. 然后以1-十八烯为高沸点溶剂, CdO 为镉源,TOP-Se为硒源, 十六胺为表面活性剂以及硬脂酸为生长促进剂和成核剂制备得到新型的Fe₃O₄-CdSe纳米异质结构. 通过透射电镜(TEM), 傅里叶变换红外(FTIR)光谱, X射线衍射(XRD)谱, X射线光电子能谱(XPS)分析仪, 振动样品磁强计(VSM), 紫外-可见(UV-Vis)光谱和光致发光(PL)等手段对Fe₃O₄-CdSe 纳米复合材料的结构和性能进行表征. 结果表明, CdSe纳米粒子成功地吸附在Fe₃O₄纳米粒子表面, 并沿着c轴生长, 形成了宽3.6 nm, 长分别为14.5 和32.5 nm的新型枣核状和钉子状的异质结构体. 这种新型的Fe₃O₄-CdSe纳米复合材料是由磁铁矿Fe₃O₄和六方形的CdSe棒状结构组成, 具有较好的荧光性能和超顺磁性. 随着CdSe棒长度的增加, 荧光吸收峰向长波方向移动. Fe₃O₄纳米粒子, 枣核状和钉子状的Fe₃O₄-CdSe纳米复合材料的饱和磁化强度分别是57.80, 40.76和31.10 emu·g^-1.     

磁性TiO2/CoFe2O4纳米复合光催化材料的制备

以磁性CoFe2O4为核,采用改进的溶胶-凝胶法,制备了磁性TiO2/CoFe2O4纳米复合光催化材料.利用VSM(振动样品磁强计)技术对其磁性能进行了研究,结果表明:由该法所得的TiO2/CoFe2O4纳米复合光催化材料的饱和磁化强度虽稍弱于纯CoFe2O4纳米材料,但其矫顽力则优于CoFe2O4.TEM、XRD、UV-Vis等的结果表明,该纳米复合材料中的TiO2为锐钛矿结构;与TiO2相比,纳米复合材料对光的吸收拓展到了整个紫外-可见区,且吸收强度大大增强.对染料废水光催化降解的模拟研究表明,该复合材料在紫外光下,6 h可以使亚甲基蓝染料溶液的脱色率达95%,且重复使用3次时染料溶液的脱色率仍能保持在90%,明显优于纯TiO2.     

Ho3+掺杂铁酸铋的制备及光催化性

为提高铁酸铋磁性和光催化性能,通过低温热分解前驱体快速制备出可磁分离回收的Ho³⁺掺杂铁酸铋复合物Bi_0.95Ho_0.05FeO₃纳米颗粒,并用X粉末衍射仪(XRD)、傅里叶红外变换光谱仪(FT-IR)、紫外可见漫反射光谱仪(DRS),磁强计(VSM)和Zeta电位仪等多种手段对物相和性质进行表征,同时以甲基橙(MO)为降解模型,考察溶液的酸碱性和常见无机阴离子共存下其光催化性能。 结果显示,产物以R3c相铁酸铋为主,带隙为1.90 eV,Ho³⁺掺杂后使铁酸铋的磁性增强了4倍,催化性能提高30%。 而该催化剂的催化性能受降解溶液本身酸碱性以及共存阴离子的氧化性与酸碱性的影响。 另外,对该催化剂的回收也进行了研究。 结果表明,所得催化剂可通过磁分离回收,从而反复利用。     

层状纳米光催化复合材料H0.8Fe0.8Ti1.2O4/TiO2的合成及性质

用固相合成法制备出K0.8Fe0.8Ti1.2O4,并用离子交换反应制备出H0.8Fe0.8Ti1.2O4;通过C3H7NH2层间膨胀,TiO2粒子的插入和紫外光分解等反应,合成出一种新的层状光催化纳米复合材料-H0.8Fe0.8Ti1.2O4/TiO2.X射线衍射和漫反射等表征结果表明 该样品的层间高度为0.47nm,禁带能隙为2.18和2.88eV.用(>400 nm的光照射30 min,0.4 g样品可使甲基橙溶液(20 mg/L)的降解率达到22.1%.而同样条件下标准TiO2(P-25)仅为6.2%,表明所研制的层状纳米复合材料具有较高的光催化活性.     

不同形貌ZnS基纳米复合材料的制备及光催化性能

采用常规溶剂热合成方法,分别以正丁胺(CH3(CH2)3NH2),己二胺(NH2(CH2)6NH2)和二乙烯三胺(NH2-(CH2)2NH(CH2)2NH2)3种有机胺为模板合成了 3种 ZnS 基纳米复合物:(a)ZnS·(n-BA)x;(b)ZnS·(HMD)x;(c)ZnS·(DETA)x.用TEM、XRD、Uv...     

掺杂铬对NiFe2O4的磁性和结构稳定性影响

利用物理特性测试仪对共沉淀法制备的Cr3+掺杂NiFe2O4的磁性能进行测试,发现掺杂Cr3+并经350、 600℃焙烧的NiFe2O4样品,饱和磁化强度Ms和剩磁Mr随掺杂量的增加而下降,矫顽磁场强度Hc随掺杂量的增加而增加.XRD平均晶粒测试结果显示,样品的平均晶粒大小随掺杂量的增加而减小.在共沉淀过程掺杂的Cr3+经600℃热处理后已进入NiFe2O4晶格.晶格中的Cr3+对NiFe2O4分解CO2的H2/CO2循环反应性能产生很大影响,纯NiFe2O4循环反应15次失活,而掺4%Cr3+的NiFe2O4循环反应50次仍然具有活性.     

Effect of Magnetic Carrier NiFe2O4 Nanoparticles on Physicochemical and Catalytic Properties of Magnetically Separable Photocatalyst TiO2/NiFe2O4

A series of magnetically separable photocatalyst TiO₂/NiFe₂O₄(TN) with different mass ratios of NiFe₂O₄ to TiO₂ was prepared by sol-gel method. The X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS), transmission electron microscopy(TEM), ultraviolet-visible spectroscopy(UV-Vis), Brunauer-Emmett-Teller(BET) surface analysis and photoluminescence spectroscopy(PL) were used to characterize the photocatalyst TN. The XRD patterns of TN indicate that adulterating a smidgen of NiFe₂O₄ into TiO₂(about 0.1%, mass ratio) can promote the phase transformation of TiO₂, however, when the doped amount of NiFe₂O₄ surpasses 1%, the introduction of NiFe₂O₄ can inhibit the growth of TiO₂ crystal grain and reduce the size of TiO₂ crystal grain. The XPS results of TN indicate that some Fe³⁺ replace Ti⁴⁺ of the TiO₂ lattice forming Fe―O―Ti bonds. The PL analysis of TN shows that the NiFe₂O₄ nanoparticles in photocatalyst TN play the role of the effective recombination centre of the photogenerated electrons and holes, leading to the decrease in photocatalytic activity.     

Preparation of CoFe2O4/sawdust and NiFe2O4/sawdust magnetic nanocomposites for removal of oil from the water surface

In this study, CoFe₂O₄/Sawdust and NiFe₂O₄/Sawdust magnetic nanocomposites were synthesized using a hydrothermal method, and then characterized using X-ray powder diffraction, Infrared, scanning electron microscopy, Brunauer–Emmett–Teller/Barrett–Joyner–Halenda, and vibrating-sample magnetometer techniques. In this study, unmodified sawdust (US), modified sawdust (MS), unmodified CoFe₂O₄/sawdust (UCS), modified CoFe₂O₄/sawdust (MCS), unmodified NiFe₂O₄/sawdust (UNS), and modified NiFe₂O₄/Sawdust (MNS) magnetic nanocomposites, which are inexpensive, economical, environmentally friendly absorbents, and have a high selective hydrophobic, were used for the removal of oil from the water surface. The results show that the UCS, MCS, UNS, and MNS magnetic nanocomposites can selectively absorb the oil spreading on the water surface, due to its superhydrophobicity and superoleophilicity, and can be easily collected from water under the influence of a magnetic field. In addition, the results showed that the absorbents reach their equilibrium at the 30-min mark. Among all the absorbents, the MNS magnetic nanocomposite showed the maximum absorption capacity (18.172 g/g) at the 40-min mark. The results of the kinetic studies showed that the second-order kinetic equation with the highest correlation coefficient had the best fit with the experimental results.     

复合电沉积制备Ni/NiFe2O4电极及其电催化析氧性能

采用共沉淀法制备尖晶石型NiFe2O4粉体,然后将其加入瓦特镀镍液中,采用复合电沉积制备Ni/NiFe2O4复合电极。通过改变镀液的pH值、阴极电流密度jk等条件,探索最佳工艺条件。运用扫描电子显微镜(SEM)、能谱分析(EDS)和X射线衍射仪(XRD)表征粉体以及复合电极的组成和结构。结果表明,在镀液pH值为5.8～6.0、jk为40×10-3～60×10-3A/cm2条件下,所得复合电极中NiFe2O4的质量分数最高可达55.15%。采用循环伏安、稳态极化以及恒电势阶跃,研究了电极在5 mol/L KOH溶液中的电催化析氧性能。与Ni电极对比,Ni/NiFe2O4复合电极的电催化析氧性能更好,比表面积是镍电极的23.02倍,表观活化能降低了62.07 kJ/mol。恒电势长时间电解析氧实验表明,Ni/NiFe2O4复合电极在碱性介质中具有较高的析氧稳定性。     

聚吡咯/铁酸镍纳米复合材料制备和应用研究

以FeCl_3为氧化剂和掺杂剂经原位氧化聚合制备了聚吡咯/铁酸镍纳米复合材料,用以吸附处理废液中高浓度的铬(Ⅵ)。分别采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和振动样品磁强计(VSM)对产物的结构、形貌与磁性能进行了表征。结果表明,复合吸附材料由20~30nm大小的NiFe_2O_4多晶球簇内核及外层聚吡咯包覆而成,其饱和磁化强度为7.89emu/g。对含铬(Ⅵ)污水吸附研究表明,该吸附剂在60min内即可达到吸附平衡,吸附效果优异,同时考察了NiFe_2O_4掺杂比例、吸附时间、pH、铬(Ⅵ)初始浓度对吸附效果的影响。在pH=5的条件下,聚吡咯/铁酸镍复合材料在30min内对铬(Ⅵ)的最大吸附量为49.81mg/g。     

Preparation and Electromagnetic Properties of Composites of Hollow Glass Microspheres Coated with NiFe2O4 Nanoparticles

"The composites of hollow glass microspheres coated with NiFe2O4 nanoparticles were prepared using polyacrylamide gel method. The structural characteristics, morphology and electromagnetic properties of the composite powders with different weight percent of glass microspheres (15%, 40%, and 65%) were obtained by X-ray diffraction, scanning electron microscope, infrared spectroscopy and HP8510 network analyzer. The results indicated that the phase structure of composite powders was the mixtures of nickel ferrite, quartz, and mullite. The peak intensity for nickel ferrite decreased rapidly and for mullite increased remarkably with the increasing amount of microspheres. A pure spinel structure of NiFe2O4 formed on the glass microspheres at 600 oC. A uniform and continuous NiFe2O4-coating was obtained when the content of microspheres was 40%. A great amount of NiFe2O4 particle size is less than 80 nm. The composite with a content of 40% microspheres exhibits better dielectric and magnetic loss properties which are useful to absorb more electromagnetic wave. It can be a kind of good and light electromagnetic wave absorbing material in the X-band."     

Hydrothermal Synthesis of g‐C3N4/NiFe2O4 Nanocomposite and Its Enhanced Photocatalytic Activity

Herein, for the first time, a direct Z‐scheme g‐C₃N₄/NiFe₂O₄ nanocomposite photocatalyst was prepared using facile one‐pot hydrothermal method and characterized using XRD, FT‐IR, DRS, PL, SEM, EDS, TEM, HRTEM, XPS, BET and VSM characterized techniques. The result reveals that the NiFe₂O₄ nanoparticles are loaded on the g‐C₃N₄ sheets successfully. The photocatalytic activities of the as‐prepared photocatalysts were evaluated for the degradation of methyl orange (MO) under visible light irradiation. It was shown that the photocatalytic activity of the g‐C₃N₄/NiFe₂O₄ nanocomposite is about 4.4 and 3 times higher than those of the pristine NiFe₂O₄ and g‐C₃N₄ respectively. The enhanced photocatalytic activity could be ascribed to the formation of g‐C₃N₄/NiFe₂O₄ direct Z‐scheme photocatalyst, which results in efficient space separation of photogenerated charge carriers. More importantly, the as‐prepared Z‐scheme photocatalyst can be recoverable easily from the solution by an external magnetic field and it shows almost the same activity for three consecutive cycles. Considering the simplicity of preparation method, this work will provide new insights into the design of high‐performance magnetic Z‐scheme photocatalysts for organic contaminate removal.     

Magnetic NiFe2O4 nanoparticles: efficient,heterogeneous and reusable catalyst for synthesis of acetylferrocene chalcones and their anti‐tumour activity

A robust synthesis of magnetic NiFe₂O₄ nanoparticles via a hydrothermal technique was investigated. The prepared magnetic NiFe₂O₄ nanoparticles were characterized using powder X‐ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy (TEM), high‐resolution TEM, energy‐dispersive X‐ray spectroscopy, thermogravimetric analysis, infrared spectroscopy and vibrating sample magnetometry. XRD and TEM analyses confirmed the formation of single‐phase ultrafine nickel ferrite nanoparticles with highly homogeneous cubic shape and elemental composition. Moreover, the prepared magnetic NiFe₂O₄ nanoparticles were used as an efficient, cheap and eco‐friendly catalyst for the Claisen–Schmidt condensation reaction between acetylferrocene and various aldehydes (aromatic and/or heterocyclic) yielding acetylferrocene chalcones in excellent yields, with easy work‐up and reduced reaction time. The products were purified via crystallization. The structures of the produced compounds were elucidated using various spectroscopic analyses (¹H NMR, ¹³C NMR, GC–MS). The catalyst is readily recovered by simple magnetic decantation and can be recycled several times with no discernible loss of catalytic activity. Furthermore, the prepared chalcone derivatives were evaluated for their anti‐tumour activity against three human tumour cell lines, namely HCT116 (colon cancer), MCF7 (breast cancer) and HEPG2 (liver cancer), and showed a good activity against colon cancer. Copyright © 2016 John Wiley & Sons, Ltd.     

红外光谱技术在纳米NiFe2O4制备过程中的应用

采用溶胶-凝胶法制备NiFe2O4纳米粉末,并经不同温度热处理.测定了制备过程中各阶段的红外吸收光谱和不同温度处理样品的红外漫反射光谱.结果表明,红外吸收光谱较好地反映了溶胶-凝胶法制备NiFe2O4纳米粉末过程中结构的变化,为确定热处理温度提供了实验依据,彻底消除有机物,热处理需在400℃以上;红外漫反射谱可以较好地反映粉末的尺寸效应和形态效应,粉末粒径越小,漫反射函数(K-M)值越大;当粒径达到一定尺寸时,红外漫反射的尺寸效应消失.