导电凝胶型全固态Ag/AgCl参比电极的制备及性能

研制出以固态AgCl~-KCl~-聚乙烯醇-琼脂混合物为导电凝胶的全固态Ag/AgCl参比电极(AllState-Referencr Electrode,简写为ASRE)。将ASRE与pH玻璃电极组成电极组,直接电位法测定pH2.00~12.00磷酸盐缓冲溶液的pH值,与以饱和甘汞电极为参比电极(SCE)的测定结果比较,相对误差为-0.8%~+0.8%;与氯离子选择电极组合测定1.00×10~(-1)~1.00×10~(-4) mol/L NaCl的电池电动势ΔE,-lgc(Cl~-)与ΔE呈良好的线性关系,斜率为-49.3,与以双盐桥SCE为参比电极时的斜率(-49.9)基本一致,表明ASRE能够代替双盐桥SCE运用于Cl~-浓度的测定。在10~80℃范围内,以KNO_3溶液(1.000 mol/L)为模型,测定ASRE相对于SCE的ΔE,ΔE与T呈线性关系,温度系数为0.123mV/℃。ASRE有望代替传统参比电极,应用于离线或在线电化学测定中。     

新型高温、长寿命氯化物熔盐参比电极的制备与研究

本文介绍一种全固态离子导电玻璃盐桥制备方法,并以此设计新型的Ag/AgCl高温参比电极.该电极制作简单, 具有电位稳定,重现性好,使用寿命长,不污染研究体系等特点.可在多种氯化物熔盐体系中反复使用,适用温度范围 400~900℃.     

宁东煤灰层/熔渣界面煤焦气化反应特性原位研究

以典型宁东煤-羊场湾煤为气化原料,采用热重分析仪和高温热台显微镜原位研究了1100、1200、1300℃下煤焦颗粒及其在灰层界面和熔渣界面的气化反应。结果表明,不同气化温度下灰层界面和熔渣界面的形态变化是影响煤焦颗粒气化反应性的主要因素。气化温度为1100℃,灰层在高温下收缩并包裹在煤焦颗粒表面,阻碍气化剂与煤焦颗粒的接触,使煤焦颗粒气化反应速率降低,而熔渣界面未发生明显变化,其界面处煤焦气化反应速率不变。气化温度为1300℃,灰层界面与熔渣界面均转变为液态,在表面张力作用下煤焦颗粒破碎,有效反应面积变大,传热速率增大,进而提高了煤焦的气化反应速率。     

液晶共聚物与PSF原位复合的界面研究

合成了两种热致性液晶共聚酯ＢＰ—ＬＣＰ和ＳＤＰ—ＬＣＰ，对其熔融指数、取向性作了考察。选用基体聚砜（ＰＳＦ）与液晶共聚酯进行熔融共混，得原位复合材料。ＳＥＭ断口形态显示了两种液晶在基体中不同的成纤性，并显示出两相的不相容性。采用ＦＴ—ＩＲ方法分析了液晶共聚酯与ＰＳＦ界面间的分子相互作用。进一步研究发现在ＰＳＦ／ＢＰ－ＬＣＰ原位复合体系中加入含ＰＳＦ和ＢＰ－ＬＣＰ的嵌段共聚物，其相容性得以改善     

全固态酸度微电极组的设计与应用

以木犀草素为pH特性敏感物,碳纤维为导电基质,固体石蜡为粘合剂制成了木犀草素碳纤维酸度微电极,将该电极与自制导电凝胶型全固态微型Ag/AgCl电极和铂丝微电极联用,构成全固态酸度微电极组。 采用循环伏安法研究了该电极组对pH值为2.00~10.00的磷酸盐缓冲溶液有效酸度的响应,结果表明,循环伏安曲线上有一对可逆氧化还原峰,两峰的峰电势均随pH值呈线性变化,据此建立了方波伏安法测定溶液酸度的方法,氧化峰的峰电势(E_pa)与pH的线性回归方程为:E_pa(V)=-0.0567pH+0.603(r=0.999),体液中常见离子及蛋白质等不干扰测定。 该电极组微型、无毒、抗干扰能力强,应用于微量体表唾液和汗液酸度的测定,取得了令人满意的结果,为微量体液的实时、在体、现场检测提供了技术基础。     

BBDMS-PPV/ITO界面结构ADXPS研究

聚合物电致发光器件（Polymer Electroluminescent Device,PLED)已显示出广阔的应用前景^[1-6]。已往人们比较重视阴极材料的选择及相关金属与有机界面的研究^[7],而有关发光层或空穴传输层与阳极ITO膜之间的界面结构及化学问题则少见报道。事实上,ITO膜与有机层之间的作用对器件的可靠性及寿命具有更为严重的影响^[8,9]。由于异质界面的过渡层结构复杂,以纳米尺度上化学组成是非计量比的,因此对这种极薄的埋藏界面的研究方法还需进一步探索。本文通过模型试样制备和变角X射线光电子谱（ADXPS）技术,对PLED中共轭导电聚合物聚2,5－二（二甲基正丁基硅基）对苯乙烯撑（BBDMS－PPV）与阳极ITO膜所形成的界面结构进行了初步研究。     

Ag/AgCl/铁-海泡石异相可见光Fenton催化降解双酚A

光-Fenton技术是高级氧化技术中的一种,常用于难降解废水处理,由于其反应速度快、毒性低、反应条件温和而受到广泛关注.然而,传统的光-Fenton体系具有可见光利用率低、回收困难等缺点.为了解决这些问题,本文采用廉价易得、无污染、吸附能力强的天然矿物海泡石作为催化剂载体,并利用Ag/AgCl能够吸收可见光的表面等离子响应这一光学性质,合成了一种有潜力的非均相等离子体光催化剂Ag/AgCl/铁-海泡石催化剂(Ag/AgCl/Fe-S),并对该催化剂的形貌结构、性能和机理等进行了系统研究.通过XRD,SEM,XPS,BET,UV-vis等表征手段对催化剂形貌、结构和可见光性能进行了分析.其中,XRD和SEM结果显示,Ag/AgCl粒子已经成功负载在Fe-海泡石上;XPS结果显示,铁氧化物的组成主要为FeOOH和Fe2O3;UV-vis结果显示,催化剂有较好的可见光吸收性能.以双酚A为目标污染物,分别考察了Ag/AgCl/Fe-S,Ag/AgCl和Fe-海泡石的光-Fenton催化性能.结果显示,Ag/AgCl/Fe-S降解双酚A的效果明显优于另外两种催化剂,在H2O2浓度为6mmol/L,pH为4,光照强度500W,Ag/AgCl/Fe-S催化剂量为1.0 g/L,双酚A初始浓度为10 mg/L的条件下,1 h时,双酚A基本被完全降解,且3 h时,其矿化率达到61.2%;而Ag/AgCl和Fe-海泡石催化剂在同样的条件下完全降解双酚A至少要3 h,且其矿化率分别只有46.61%和28.85%.另外,还分别探讨了H2O2浓度、pH值、光照强度和催化剂剂量对双酚A降解的影响.最后,通过活性物种捕获、ESR、电化学和PL实验对该体系的反应机理进行了探讨.活性物种捕获实验和ESR实验结果表明,羟基自由基(?OH)和空穴(h+)是该体系中的主要活性物种,且Ag/AgCl/Fe-S+H2O2+vis体系产生的?OH明显多于Fe-S+H2O2+vis体系.为了探讨?OH增多的原因,我们进行了电化学实验和PL实验.电化学实验结果显示,Ag/AgCl/Fe-S催化剂具有更低的阻抗,因此有利于电子-空穴分离.PL结果显示,Ag/AgCl/Fe-S催化剂的电子-空穴复合率更低.结合以上实验,我们提出了Ag/AgCl/Fe-S+H2O2+vis体系对双酚A的降解机理,即一方面催化剂能够发生Fenton反应而产生?OH,另一方面,催化剂中的Ag/AgCl在可见光下由于表面等离子响应而产生电子-空穴,空穴本身可作为活性物种降解双酚A.同时,产生的电子被体系中的Fe3+捕获生成Fe2+,从而促进了铁循环,有利于体系中产生更多的?OH.最后,空穴和羟基自由基发生协同作用共同促进污染物降解.     

微波原位合成Ag NPs/MoS2复合材料及其电化学性能

二硫化钼纳米片(MoS₂)受到带电杂质、结构缺陷和易聚集等因素的影响,导致其电子转移性能下降,使其应用受限。将银纳米颗粒(Ag NPs)与少层MoS₂纳米片复合,可提升MoS₂纳米片的电化学性能。本研究创新性地采用微波还原法,使Ag NPs原位沉积于MoS₂,得到Ag NPs/MoS₂复合材料。结果表明,将Ag NPs/MoS₂复合材料修饰于丝网印刷电极(screen printed electrodes,SPE)后,测得的循环伏安(cyclic voltammetry,CV)曲线峰电流值为同浓度单一MoS₂修饰电极的1.8倍,方波伏安(square wave voltammetry,SWV)曲线峰电流值为单一MoS₂修饰电极的3.4倍,电化学阻抗谱(electrochemical impedance spectroscopy,EIS)的电子转移阻抗值(Ret)仅为167Ω,相比MoS₂/S...     

可见光响应光催化剂Ag/AgCl@NH2-UiO-66的制备及其光催化性能

采用气相扩散-沉积-光还原法制备了可见光响应复合光催化剂Ag/AgCl@NH_2-UiO-66。通过X射线衍射(XRD)、电子扫描显微镜(SEM)、X射线能谱(EDS)、紫外可见漫反射光谱及X射线光电子能谱(XPS)等对催化剂的结构进行了表征。结果表明Ag/AgCl@NH_2-UiO-66具有优良的光催化活性,可见光条件下(λ≥420nm)对20mg·L~(-1)罗丹明的降解效率14min即可达到98%。     

液/液界面电分析化学研究进展

本文对液/液界面电分析化学近年来的进展进行了综述,特别是结合我们自己的工作,对探讨液/液界面微观结构和构筑新型液/液界面方面的进展进行了重点介绍.目前通过理论模拟和各种实验技术的应用,液/液界面微观结构已初具轮廓;可供选择的有机相也得到了一定的拓展.这些进展为该领域今后的发展打下了基础并指明了方向.     

电极/溶液界面pH值的现场测量

一般认为阴极表面功能陶瓷电沉积层的形成是由于基底 /溶液界面化学环境变化造成的 [1,2 ] ,但目前还没有直接的实验数据加以证明 .原位测量电极 /溶液界面 p H的变化存在两方面的困难 :(1 )传统方法是采用玻璃 p H计 ,由于其体积较大、强度脆弱等原因 ,使其在测量固 /液界面化学环境变化的应用方面受到一定限制 [3 ] ;(2 )将 p H微探针置于电极表面 ,将会影响功能陶瓷在电极表面的沉积 ,从而使测定的界面 p H值不能真实反映电沉积过程中固 /液界面化学环境的变化 .本文基于功能陶瓷电沉积过程不受影响的情况下现场直接测量电极 /溶液界面…     

Electrochemistry Investigation on the Graphene/Electrolyte Interface

In this study, the graphene/electrolyte interface was investigated in detail by the electrochemical method. The total interface capacitance was calculated from the electrochemical impedance spectroscopy (EIS) results, and its responses to different concentrations and pHs were also investigated. The minimum point of the capacitance was found to shift to right (vs. Ag/AgCl) as the concentration increased, and to left with increasing pH. As a comparison, gold/electrolyte interface was investigated in the same way, but didn’t show the similar behavior. To further explore the interface capacitance, proper models were proposed to fit the EIS results. Two constant‐phase elements (CPE) were used in the graphene‐electrolyte interface model to represent the double‐layer capacitance (CPE_dl) and the quantum capacitance (CPE_q), respectively. The CPE_q exhibited its sensitivity to concentration and pH, while CPE_dl did not. This study gives a new aspect to detect concentration and pH, and may provide a reference for the graphene‐based supercapacitor research.     

Electrochemical Immunosensing Chip Using Selective Surface Modification,Capillary‐Driven Microfluidic Control,and Signal Amplification by Redox Cycling

A sensitive electrochemical immunosensing chip is presented by employing (i) selective modification of protein‐resistant surfaces; (ii) fabrication of a stable Ag/AgCl reference electrode; (iii) capillary‐driven microfluidic control; (iv) signal amplification by redox cycling along with enzymatic reaction. Purely capillary‐driven microfluidic control is combined with electrochemical sandwich‐type immunosensing procedure. Selective modification of the surfaces is achieved by chemical reactivity‐controlled patterning and electrochemical deposition. Fluidic control of the immunosensing chip is achieved by spontaneous capillary‐driven flows and passive washing. The detection limit for mouse IgG in the immunosensing chip is 10 pg/mL.     

纳米锐钛矿相变的原位XRD研究

钛氧化物具有3种物相：锐钛矿、板钛矿和金红石，其中，锐钛矿和板钛矿为室温稳定相．在温度较高的条件下会向热力学更稳定的金红石相转变。锐钛矿向金红石的相变是热力学亚稳定相向稳定相的转变，由于这种相变过程不存在平衡温度．分析研究其相变过程无论从理论方面还是从实际应用方面均具有重要的意义。     

In-situ pH Measurement at the Electrode/Solution Interface

ElectrochemicaldepositionoffunctionalceramiccoatingshasrecentlyattTactedconsiderableattention'-3becauseofavarietyofadvantagesofthemethodofthecoatingfabrication,suchasalowprocesstemPeratUre,theabilitytodepositonporousorcomplexshaPesofsubstrae,thesimPlecontrolofdepositthickness.Themechanismofelectrodepositionforfunctionalceramicsontothesubstr8tehasnotbeenfiJllyclarifiedatpresent.ltwasgenerallygUessed"'thattheelectrochemicalreactionsontheelectrodesurfacemaycauseapHchangeatthecathode/solutionint…     

Development of a micro-planar Ag/AgCl quasi-reference electrode with long-term stability for an amperometric glucose sensor

This paper reports a micro-planar Ag/AgCl quasi-reference electrode (QRE) with long-term stability which is characterized by both long-term potential stability and practical immunity to interference species, and which has been applied for use with an amperometric glucose sensor for plasma glucose. For fabrication, we coated a silver/silver chloride (Ag/AgCl) electrode first with γ-aminopropyltriethoxysilane (γ-APTES) and then with perfluorocarbon polymer (PFCP). Tests demonstrate the new electrode’s ability to remain stable over an 82-day period in 150 mM KCl, and also show its imperviousness to the effects of interference species (1 mM KI and 1 mM KBr), pH, and serum. Furthermore, in tests for glucose concentrations in plasma samples, a good correlation coefficient, 0.954 (n=30, Y=1.02X+0.20), was demonstrated between results obtained with a clinical analyzer and those obtained with an amperometric glucose sensor that used the developed Ag/AgCl QRE, showing that the Ag/AgCl QRE functions well as a reference electrode for plasma samples.     

负载型Cu/Al2O3和Cu/ZnO催化剂上CO2加氢的原位FTIR及准原位XPS/HS-LEIS研究

铜基催化剂是工业合成甲醇中常用的催化剂,其主要包含Cu,ZnO,Al2O3三种组分,研究各组分在催化合成甲醇过程中的本质作用及其相互间的协同作用不仅是一个催化基础科学问题,同时对于设计和合成新型高性能的铜基催化剂也有重要指导作用.以往的研究主要针对Cu和ZnO二元组分,关于Al2O3的作用很少有报道,主要观点认为Al2...     

An Arrayed Micro‐glutamate Sensor Probe Integrated with On‐probe Ag/AgCl Reference and Counter Electrodes

Complete all‐in‐one multi‐arrayed glutamate (Glut) sensors have been constructed on a silicon‐based micromachined probe composed of micro‐platinum (Pt) working electrodes, a micro‐silver/silver chloride (Ag/AgCl) reference electrode (RE), and a micro‐Pt counter electrode (CE). The OCP shift of the electrodeposited Ag/AgCl on‐probe micro‐reference electrode compared with a Ag/AgCl wire is <0.1 mV/h. The composition ratio of Ag, Cl, and Pt on the electrodeposited on‐probe micro‐reference electrode is observed to be 1.00 : 0.48 : 0.02 analyzed by EDS. The miniaturized amperometric Glut biosensors were constructed on working electrode sites (electrode area: ∼8.5×10⁻⁵ cm²) of the microprobe modified with glutamate oxidase (GlutOx) enzyme layers for the selective, fast, and continuous detection of L‐glutamate. The sensor selectivity towards common electroactive interferents has been improved significantly by coating the electrode surface with perm‐selective polymer layers, overoxidized polypyrrole (PPY) and Nafion®. The sensitivity, detection range, and response time of the proposed all‐in‐one Glut biosensors are 204.7±5.8 nA μM⁻¹ cm⁻² (N=5), 4.99–109 μM, and 2.7±0.3 sec, respectively and no interferent signals of AA and DA were observed. The sensor can be reused over 19 times of continuous repetitive operation (total measurement time: ∼4 hours) and the sensor sensitivity can retain up to four weeks of storage.