P(AMPS-co-BMA)水凝胶的电场敏感性及电刺激响应机理

以离子型单体2-丙烯酰胺-2-甲基丙磺酸(AMPS)及非离子型单体甲基丙烯酸丁酯为原料, 偶氮二异丁腈为引发剂, N,N′-亚甲基双丙烯酰胺为交联剂, N,N-二甲基甲酰胺为溶剂, 通过自由基聚合合成了一系列聚离子浓度不同的聚(2-丙烯酰胺-2-甲基丙磺酸-co-甲基丙烯酸丁酯)电场敏感性水凝胶. 研究了其在去离子水及NaCl溶液中的溶胀行为. 结果表明, 该水凝胶在去离子水中的平衡溶胀度在236.4~298.5之间, 其溶胀速率随着AMPS用量的增加而增加; 并且随着凝胶内部聚离子浓度的增加, 凝胶在NaCl溶液中的消溶胀速率及消溶胀度逐渐减小. 凝胶的电刺激响应性能研究结果表明, 在电场存在下, 凝胶在NaCl溶液中的溶胀行为与凝胶内部聚离子浓度和溶液中NaCl浓度的相对大小有关, 当凝胶内部聚离子浓度大于溶液中NaCl浓度时, 凝胶溶胀, 反之则凝胶消溶胀; 而且, 凝胶在电场作用下的偏转行为同样与凝胶内部聚离子浓度和溶液中NaCl浓度的相对大小有关, 当凝胶内部聚离子浓度大于溶液中NaCl浓度时, 偏向阴极, 反之则凝胶偏向阳极. 另外, 在电场存在下, 凝胶在NaCl溶液中的电偏转速度与环境温度密切相关.     

PAMPS/SiO_2杂化水凝胶的合成及电场敏感性研究

以2-丙烯酰胺-2-甲基丙磺酸(AMPS)为有机原料,正硅酸乙酯(TEOS)为无机原料,过硫酸钾为引发剂,N,N'-亚甲基双丙烯酰胺为交联剂,通过原位-凝胶水溶液聚合法合成了一系列不同二氧化硅含量和不同聚离子浓度的聚(2-丙烯酰胺-2-甲基丙磺酸)/二氧化硅杂化电场敏感性水凝胶.通过扫描电子显微镜(SEM)表征凝胶的结构,研究水凝胶在去离子水以及氯化钠溶液中的溶胀和消溶胀行为.结果表明,系列凝胶的平衡溶胀度介于224.9至325.6之间,复合凝胶的溶胀速率随TEOS用量的增加而降低;除理想杂化凝胶外,随着聚离子浓度的升高,凝胶在氯化钠溶液中的消溶胀速率逐渐减小.对凝胶的电场敏感性研究表明,当聚离子浓度大于氯化钠溶液浓度时,凝胶进一步溶胀,反之则消溶胀,其中杂化凝胶的再溶胀性能减弱,而消溶胀行为变得更为明显.同时制得的理想杂化凝胶,较纯有机凝胶具有更为理想的力学性能,最大抗压缩强度可达23.4 MPa.     

有机-无机纳米复合水凝胶*

本文综述了近年来有机-无机纳米复合水凝胶领域的研究进展。针对无机成分的不同种类及复合形式,本文将目前已见报道的有机-无机纳米复合水凝胶划分为三类,分别为层状硅酸盐纳米插层复合水凝胶、粘土交联纳米复合水凝胶和二氧化硅纳米杂化复合水凝胶。阐述了三类纳米复合水凝胶的发展趋势,特别就它们的合成方法进行了详细归纳与总结。在此基础上,介绍了纳米无机成分对复合水凝胶的性能增强机理,并就三者之间的增强差异进行了说明。     

明胶凝胶表面润湿性的研究

本工作利用测定几种参照液体在明胶凝胶上的接触角,定量地估算了明胶凝胶的表面自由能。加入表面活性剂,尤其是非离子表面活性剂,能增加明胶凝胶的表面自由能(主要是其极性分量)并大大改善明胶凝胶的表面润湿性。在表面上分子的吸附与定向和明胶凝胶中非极性网状结构形成的基础上,解释了上述实验结果。     

Biomimetic Extreme-Temperature- and Environment-Adaptable Hydrogels

Recently, temperature-resistant hydrogels, hydrogels which are freezing- and dehydration-resistant, have garnered considerable attention in the scientific community as they extend the rage of application of hydrogels to arid and/or cold environments. Besides, these hydrogels exhibit tunable conductivity and mechanical performance while offering excellent biocompatibility and flexibility, making them interesting candidates for flexible and wearable electronics and (bio)sensors. Several biomimetic strategies were developed to fabricate anti-freezing and anti-dehydration hydrogels with a diversity of merits, such as high strain resistance and conductivity, even at sub-zero temperatures, and employed as (bio)sensors, electrodes, and energy-storage devices. This review summarizes the recent advances in the preparation and application of temperature-resistant hydrogels, indicates issues of the state-of-the-art hydrogels, and offers potential future research directions.     

烷氧磺酸盐功能化的聚乙撑二氧噻吩水凝胶

通过氧化偶联聚合方法成功地制备出一种基于烷氧磺酸盐功能化的聚乙撑二氧噻吩水凝胶, 揭示了零维单体胶束向二维纳米片层及三维水凝胶的转变过程, 发现通过改变反应温度或初始单体浓度, 可以诱导水凝胶网络结构单元的维度变化, 即由零维纳米粒子向二维纳米片层进行转化. 提出了一种导电高分子水凝胶的合成方法, 即采用一种氧化剂与一种多价金属盐的混合物作为引发剂, 其中前者用于诱导单体聚合, 后者则充当离子交联试剂, 并发现可以通过引入不同金属离子来改变凝胶的形貌. 此外, 导电高分子水凝胶具有良好的电化学电容, 并具有选择性吸附与可控脱附某些染料分子的特性.     

A Rapidly and Highly Self-Healing Poly(Sulfobetaine Methacrylate) Hydrogel with Stretching Properties,Adhesive Properties,and Biocompatibility

This study focuses on the preparation of stretchable zwitterionic poly(sulfobetaine methacrylate) (PSBMA) hydrogels. To address the weak mechanical properties of chemically crosslinked PSBMA hydrogels, a physical crosslinking method utilizing hydrophobic interactions to crosslink hydrogels to approach tough properties is developed. Here, sodium dodecyl sulfate (SDS)-based micelle is used as a physical crosslinker to prepare physically crosslinked PSBMA (PSBMA_phy) hydrogels, and ethylene glycol dimethylacrylate (EGDMA) is used to prepare a control group of chemically crosslinked PSBMA (PSBMA_chem) hydrogels. The mechanical properties of the two hydrogels are compared, and PSBMA_phy hydrogels exhibit greater flexibility than the PSBMA_chem hydrogels. When the PSBMA_phy hydrogels are subjected to external forces, the micelles act as dynamic crosslinking sites, allowing the stress to disperse and prevent the hydrogel from breaking. In addition, the PSBMA_phy hydrogels have nearly 100% self-healing properties within 2.5 min. The PSBMA_phy hydrogels exhibit usable adhesive properties to porcine skin and subcutis. MTT and hemolysis tests show that the PSBMA_phy hydrogels have excellent biocompatibility and hemocompatibility. This study proposes that the multifunctional PSBMA_phy hydrogels with micelles will be potential to carry drugs for use in drug delivery systems in the future.     

Preparation and Characterization of Attractive Poly(amino acid)Hydrogels Based on 2-Ureido-4[1H]-pyrimidinone

Self-healing hydrogels with the shear-thinning property are novel injectable materials and are superior to traditional injectable hydrogels.The self-healing hydrogels based on 2-ureido-4[1 H]-pyrimidinone(UPy)have recently received extensive attention due to their dynamic reversibility of UPy dimerization.However,generally,UPy-based self-healing hydrogels exhibit poor stability,cannot degrade in vivo and can hardly be excreted from the body,which considerably limit their bio-application.Here,using poly(l-glutamic acid)(PLGA)as biodegradable matrix,branchingα-hydroxy-ω-amino poly(ethylene oxide)(HAPEO)as bridging molecule to introduce UPy,and ethyl acrylate polyethylene glycol(MAPEG)to introduce double bond,the hydrogel precursors(PMHU)are prepared.A library of the self-healing hydrogels has been achieved with well self-healable and shear-thinning properties.With the increase of MAPEG grafting ratio,the storage modulus of the self-healing hydrogels decreases.The self-healing hydrogels are stable in solution only for 6 h,hard to meet the requirements of tissue regeneration.Consequently,ultraviolet(UV)photo-crosslinking is involved to obtain the dual crosslinking hydrogels with enhanced mechanical properties and stability.When MAPEG grafting ratio is 35.5%,the dual crosslinking hydrogels can maintain the shape in phosphate-buffered saline solution(PBS)for at least 8 days.Loading with adipose-derived stem cell spheroids,the self-healing hydrogels are injected and self-heal to a whole,and then they are crosslinked in situ via UV-irradiation,obtaining the dual crosslinking hydrogels/cell spheroids complex with cell viability of 86.7%±6.0%,which demonstrates excellent injectability,subcutaneous gelatinization,and biocompatibility of hydrogels as cell carriers.The novel PMHU hydrogels crosslinked by quadruple hydrogen bonding and then dual photo-crosslinking of double bond are expected to be applied for minimal invasive surgery or therapies in tissue engineering.     

快速响应温敏水凝胶研究进展

温敏水凝胶是一类具有广泛应用前景的高分子材料,但是由于传统方法合成的水凝胶响应速率较慢因而限制了其应用,因此近年来围绕提高传统水凝胶的响应速率做了大量研究工作。本文从几个方面综述了近年来快速响应的温敏水凝胶的研究进展,并对有关现象进行了解释和说明。     

Current research progress of photopolymerized hydrogels in tissue engineering

Owing to the special fo rmation of photopolymerized hydrogels,they can effectively control the formation of hydrogels in space and time.Moreover,the photopolymerized hydrogels have mild formation conditions and biocompatibility;therefore,they can be widely used in tissue engineering.With the development and application of manufacturing technology,photopolymerized hydrogels can be widely used in cell encapsulation,scaffold materials,and other tissue engineering fields through more elaborate manufacturing methods.This review covers the types of photoinitiators,manu facturing technologies for photopolymerized hydrogels as well as the materials used,and a summary of the applications of photopolymerized hydrogels in tissue engineering.     

Rapidly in situ forming biodegradable robust hydrogels by combining stereocomplexation and photopolymerization

Our previous studies have shown that stereocomplexed hydrogels can be rapidly formed in vitro as well as in vivo upon mixing aqueous solutions of eight-arm poly(ethylene glycol)-poly(l-lactide) (PEG-PLLA) and poly(ethylene glycol)-poly(d-lactide) (PEG-PDLA) star block copolymers. In this study, stereocomplexation and photopolymerization are combined to yield rapidly in situ forming robust hydrogels. Two types of methacrylate-functionalized PEG-PLLA and PEG-PDLA star block copolymers, PEG-PLLA-MA and PEG-PDLA-MA, which have methacrylate groups at the PLA chain ends and PEG-MA/PLLA and PEG-MA/PDLA, which have methacrylate groups at the PEG chain ends, were designed and prepared. Results showed that stereocomplexed hydrogels could be rapidly formed (within 1-2 min) in a polymer concentration range of 12.5-17.5% (w/v), in which the methacrylate group hardly interfered with the stereocomplexation. When subsequently photopolymerized, these hydrogels showed largely increased storage moduli as compared to the corresponding hydrogels that were cross-linked by stereocomplexation or photopolymerization only. Interestingly, the storage modulus of stereocomplexed-photopolymerized PEG-PLA-MA hydrogels increased linearly with increasing stereocomplexation equilibration time prior to photopolymerization (from ca. 6 to 32 kPa), indicating that stereocomplexation aids in photopolymerization. Importantly, photopolymerization of stereocomplexed hydrogels could take place at very low initiator concentrations (0.003 wt %). Swelling/degradation studies showed that combining stereocomplexation and photopolymerization yielded hydrogels with prolonged degradation times as compared to corresponding hydrogels cross-linked by photopolymerization only (3 vs 1.5 weeks). Stereocomplexed-photopolymerized PEG-MA/PLA hydrogels degraded much slower than corresponding PEG-PLA-MA hydrogels, with degradation times ranging from 7 to more than 16 weeks. Therefore, combining stereocomplexation and photopolymerization is a novel approach to obtain rapidly in situ forming robust hydrogels.     

Preparation of Injectable Composite Hydrogels by Blending Poloxamers with Calcium Carbonate-Crosslinked Sodium Alginate

The effects of calcium carbonate-crosslinked sodium alginate on poloxamer hydrogels have been investigated. The mechanical strength, degradability, and thermal stability of hydrogels were characterized. The chemical and physical crosslinking in the composite hydrogels has resulted in an improvement of the compressive strength and elasticity of the hydrogels. These mixed hydrogels showed improved mechanical properties, elasticity, and stability as well as environmental responsiveness and injectability.     

Hybrid Hydrogels Toughened by Chemical Covalent Bonding and Physical Electrostatic Interactions

Polystyrene nanoparticles with negative charges(n-PSs) were synthesized using styrene(St) and sodium styrene sulfonate(NaSS) as initial materials by surfactant-free emulsion polymerization. Subsequently, a hybrid hydrogel was prepared using acrylamide(AAm) and methacryloyloxyethyltrimethyl ammonium chloride(DMC) as co-monomers with N,N'-methylenebisacrylamide(MBA) as a chemical crosslinker and n-PSs as a physical electro-static interaction agent. The resulting hybrid hydrogels exhibited excellent tensile strength and elongation at break. The tensile stress of hybrid hydrogels was seven times greater than that of hydrogels without n-PSs. The elongation at break of hydrogels reached 700%, which was much higher compared to those of the hydrogels without n-PSs. Furthermore, swelling measurements of the hydrogels indicate that there is an overshoot in the swelling process and the extent of overshoot decreases with the increasing n-PSs. Therefore, the work presented here provides a method for improving the mechanical properties of hydrogels via the introduction of polymeric nanoparticles.     

Characterization and evaluation of silk protein hydrogels for drug delivery

The objective of this study was to characterize and evaluate the physicochemical properties and drug release profiles of hydrogels composed of silk protein (SP) polymers. SPs with a low MW (SPL, ca. 18 kDa) and a high MW (SPH, ca. 76 kDa) were used for preparing hydrogels. Both the random coil form and beta-sheet conformation simultaneously existed in the hydrogels according to Fourier-transformed IR determination. Morphologically, the hydrogels showed a sponge-like cross-linked structure produced by physical entanglement as well as chemical hydrogen and covalent bindings. The in vitro buprenorphine delivery from SPH hydrogels showed a slow-release effect, and a zero-order rate was obtained for all preparations. Drug release could be controlled by varying the SPH concentrations or incorporation of SPL into the systems. SP hydrogels showed a stronger barrier property for hydrophilic solutes than for hydrophobic solutes. The incorporation of SPH into Pluronic F-127 (PF-127) hydrogels changed the gel structure from amorphous micelles to a regularly interconnected texture with pores. Furthermore, SPH as an adjuvant polymer in PF-127 and chitosan hydrogels lowered and controlled the amount of drug released from those systems.     

水凝胶及其在药物控释体系上的应用

智能水凝胶作为药物载体有着良好的应用前景。人体环境中存在一些变化的因素，如温度、pH。因此，温度敏感性水凝胶和pH敏感性水凝胶可用于药物在人体中的控释体系。本文主要介绍水凝胶材料的种类以及智能水凝胶在药物控释体系上的应用。     

Curcumin-loaded PLGA-PEG-PLGA triblock copolymeric micelles: Preparation, pharmacokinetics and distribution in vivo

Rod-shaped cellulose nanocrystals (CNCs) were manufactured and used to reinforce polyacrylamide (PAM) hydrogels through in situ free-radical polymerization. The gelation process of the nanocomposite hydrogels was monitored on a rheometer using oscillatory shear. The chemical structure, morphology, swelling property, and compression strength of the formed gels were investigated. A possible mechanism for forming hydrogels was proposed. The results showed that CNCs accelerated the formation of hydrogels and increased the effective crosslink density of hydrogels. Thus CNCs were not only a reinforcing agent for hydrogel, but also acted as a multifunctional cross-linker for gelation. The shear storage modulus, compression strength and elastic modulus of the nanocomposite hydrogels were significantly improved because of good dispersion of CNCs in PAM as well as enhanced interfacial interaction between these two components. Among the CNC contents used, a loading of 6.7 w/w% led to the maximum mechanical properties for nanocomposite hydrogels.     

水凝胶流变学研究概况

水凝胶具有良好的生物相容性和生物可降解性,其结构呈三维网状结构,与细胞外基质相似,在药物释放和组织工程等领域具有广阔的应用前景,被广泛地用于生物制药、生物材料和医学等领域。流变学可以描述材料的流动特性和力学性能,水凝胶的粘弹响应对材料内部结构的变化也非常敏感,因此流变行为被视为研究水凝胶的一种重要方法。本文综述了流变学方法在水凝胶研究中的应用,介绍了水凝胶流变学的研究方法,讨论了影响水凝胶流变学特征的因素,并展望了水凝胶流变学的发展前景。     

原子转移自由基聚合在智能型水凝胶制备中的应用

分别对原子转移自由基聚合和智能型水凝胶两者进行了综述,分析总结了利用原子转移自由基聚合制备智能型水凝胶方面的应用情况,并对其前景作了一定的展望.     

Fluorescence resonance energy transfer by quencher adsorption into hydrogels containing fluorophores

We synthesized anionic hydrogels containing fluorophores and investigated the adsorption of a cationic quencher having an amino group into hydrogels by fluorescence resonance energy transfer (FRET). FRET from the fluorophore to the quencher in hydrogels was examined by fluorescence intensity and fluorescence decay using a fluorescence spectrophotometer and femtosecond laser spectroscopy. The fluorescence intensity of the fluorophore‐containing hydrogels decreased rapidly with increasing amounts of adsorbed cationic quencher. The fluorescence emission of the fluorophore in the quencher‐adsorbed hydrogels containing fluorophores decayed more rapidly than that of the original hydrogels. The aforementioned result indicates that the fluorescence of the fluorophore‐containing hydrogels is quenched due to FRET from the fluorophore to the quencher as the cationic quenchers can approach the fluorophores in hydrogels by electrostatic interactions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3245–3252, 2006     

Nanocomposite hydrogels based on carbon dots and polymers

Nanocomposite hydrogels based on carbon dots(CDs) and polymers have emerged as new materials with integrated properties of individual components,leading to their important applications in the field of soft nanomaterials.This perspective highlights recent advances in the development of nanocomposite hydrogels from CDs and polymers.We review the preparation methods of nanocomposite hydrogels based on CDs and polymers,and emerging applications of these nanocomposite hydrogels such as environmental remediation,energy storage,sensing,drug delivery and bioimaging.We conclude with the discussion of new research directions in the development of new type of nanocomposite hydrogels based on CDs and polymers.